Search Documents

By J. N. Van der Merwe

The results of over 900 coal strength tests done during the period 1993?1994 for the SIMRAC project COL021A were re-analysed with a view to find a method to delineate areas or seams that can be grouped together for analyses of coal strength and strength decay characteristics. It was confirmed that the strength of a coal specimen increases linearly with increasing diameter-to-length ratio and decreases exponentially with increasing size of specimen. However, by extrapolation of the data, it was shown that beyond a diameter of approximately 2 m, the size effect is insignificant. For larger specimens, the diameter-to-length ratio (referred to as the width-to-height ratio for full scale mine pillars) alone continues to influence the strength. The slope of the linear strength vs. diameter-to-length ratio relationship is independent of the size of the specimen and is not unique for coals from different mines. However, the intercept of that relationship is unique and is a function of specimen size. This offers a previously unknown method to distinguish between the coals from different mining areas and coal seams. Ranked from weakest to strongest, the samples tested from the different mines are in the order shown below, which roughly corresponds to the judgement of practising rock engineers in the field: ?Sigma ?ZAC ?Goedehoop ?Kriel ?Bank ?Blinkpan ?Secunda ?Greenside Arnot ?Khutala ?Delmas

Jan 1, 2003

By Eric Dussell

Commercial or industrial explosives are mechanically-mixed, fuel-oxidizer composites which exhibit varying degrees of non-ideal behavior. Non-ideality results from a relatively slow and state-insensitive reaction rate (Lee, 1990) and is characterized by C-J pressures, velocities or expansion isentropes significantly lower than those expected from equilibrium, steady-state calculations such as Tiger or BKW (Mader, 1979). This departure results from significant amounts of explosive material which remain unreacted at the sonic point. Energy released by continued combustion within the emergent supersonic region downstream of the sonic point, constrained by local sound speed, cannot flow to the shock front and do work on it. The significant amount of this ‘late energy” and its slow time rate of release must be considered in any blast performance model.

Jan 1, 1997

By Alten F. Grandt

What is prime farmland? Can such land, once it has been surface mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on surface mined land in St. Clair County (Grandt, 1949). This research was done almost thirty years before requirements of Public Law 95-87 were passed by the US Congress and signed August 3, 1977.

Jan 1, 1982

By D. S. Nilsson

Small-scale mines are today expected to provide much of the increased production of metals and coal this county demands. But in fact the category of larger mines tends to grow in number and size faster than the category of smaller mines. Larger mines show the highest productivity, the lowest injury frequency, and the lowest costs. Lower cutoff grades can be wed in larger mines. The paper describes how the production level affects the choice between different types of loading, haulage, and hoisting equipment; how the increased production level in a mine results in lower production costs per ton; and how this affects the profitability of mining deposits with various ore grades. The future trend is expected to favor larger and larger operations.

Jan 1, 1983

By R. M. Schuster, F. M. Benavides

A plan is prepared to develop and operate a four mine complex over a 30-year period. The mining complex is in the vicinity of two existing processing plants and the most economical means of transporting the raw minerals to either or both of these processing plants is sought. The mines and processing plants are all within a radius of 5.6 km (3.5 miles). Existing transportation facilities consist of county and state roads and federal highways as well as haul roads in some areas. A navigable river meanders through the area under study and there are two railroad systems servicing the area. The analysis shows the economic and operational feasibility of using an overland conveyor in lieu of other means of transportation.

Jan 1, 1983

By J. L. Broadhurst, S. Rumjeet, S. T. L Harrison, T. Chimbganda

Post-mining land use for the production of industrial crops has the potential to mitigate environmental and socio-economic impacts of mine closure and stimulate post-mining economic growth. Fibre-rich plants are of particular interest due to their multi-product potential. In the South African context, where there are many abandoned and end-of-life mines near human settlements, an opportunity presents to assess the feasibility of transforming post-mining land into productive land and building resilient communities through the development of multi-product value chains from fibre-rich plants such as kenaf, hemp or bamboo. This paper provides an overview of the plant selection criteria, phytoremediation potential and the downstream options for the recovery of products and value from bast fibre plants (hemp and kenaf) and bamboo. Based on findings from a comprehensive review of the published literature, as well as interviews with relevant experts within South Africa, it appears that bast fibre plants are the best downstream option for producing ‘green’ textiles and high-end niche products, whereas bamboo is more suitable as a replacement for conventional timber. Although fibre plants have the potential to extract metals from soils, high concentrations may inhibit plant growth and affect the quality of the final fibre product. Further site-specific studies would thus be required to select the best route for both land remediation and optimal product recovery. Keywords: Bioremediation, bamboo, kenaf, hemp, multi-product value chains, sustainable postmining land use

Jan 1, 2020

By John W. Brauns, David H. Orr

9.1-1. Description and Basic Function. A conventional railroad haulage system for a surface mine performs the function of transporting the ore and/or waste out of the pit to a crushing plant or dump. Trains consisting of a locomotive and gondola or side-dump care suitable for loading by power shovels are used. Gondola cars are restricted to hauling ore as a rotary dumper is required to unload them. Side-dump cars are more versa- tile, being satisfactory for carrying both ore and waste; but because of their additional dumping mechanism they are likely to be more expensive to maintain (12). Also they weigh up to two times as much as a flat-bottom car of the same capacity, and, therefore, fewer cars can be hauled per train. Standard-gauge track is most commonly used. Track systems incorporate temporary track of low quality in areas where moves are frequent and permanent track of high quality on main lines. Rail haulage enabled open pit mining to establish its reputation, for efficiency. Prior to World War II it was the principal type of transportation used in large pits. Other successful surface mine haulage methods have been developed since that time. These have served to supplement railroad transportation, permitting selection of a method that is best adapted to the peculiar requirements of each mining project. 9.1-2. General Applicability and Controlling Physical Conditions. For handling rough rock, the shovel-train system is unexcelled (6). The ideal application is in a physically large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transported than will any other haulage method. Relatively gentle

Jan 1, 1968

The Geograph is a revolutionary seismic system involving special techniques in combining the use of FIT magnetic tape with shock wave echoes created by a weight dropping system.The idea of- weight dropping as a- source of seismic energy is not a new,.,oxie. Records 'indicate òa pos'sihle use of falling weights as early as .1929. 'Dr. Burton McCollum began his experiments in 1938, but it wasn't until 1951 that the method was first proven useful.The first weight dropping crew began commercial operations in Edwards and Sutton .Counties of West Texas in 1953. By 1962, more than '40 weight drop-ping.crews have come into existence with operations in the United States, Canada, Algeria, Iraq, Argent na,òSpanish West Africa, Tunisia, Qatar, Niger Morocco and Libya by most major oil companies and larger independent oil companies. .

Jan 1, 1962

By Richard E. Lounsbury

Coal mine refuse handling traditionally has been the redheaded stepchild of the industry-a problem to be ignored as much as possible. During the past few years, however, mining companies have become more aware of the potential water pollution problem associated with refuse handling and storage. Planning for refuse disposal involves environmental protection and the economics of refuse handling. For over two years, Monterey Coal Co. has operated a non-polluting refuse disposal system at its No. 1 Mine located in Brushy Mound Township of Macoupin County 6 miles south of Carlinville, Illinois. Drainage goes to Spanish Needle Creek and eventually to the Illinois River. The mine produced 3.5 million tons of clean coal during its first two and one-half years of operation and is designed to produce 3 million tpy of clean coal at capacity.

Jan 6, 1973

By Mark A. White

Surface mining of multiple seams by mountaintop removal and contour mining is complex in Appalachia. Arch of West Virginia, a division of Apogee Coal, has made its operations state-of-the-art to cope with this challenge. Arch of West Virginia moved into the heart of coal mining in Appalachia when Arch Mineral acquired coal reserves and coal operations in the southern West Virginia counties of Logan and Wyoming. These reserves were initially developed at the turn of the century as underground operations. Today, though, they are mined using mountaintop removal and contour mining. The steep slopes in the mountains of Appalachia generated a method of mining referred to as contour mining. During the late 1960s and early 1970s, contour mining was introduced at these operations using front-end loaders with bucket capacities of more than 7 m3 (10 cu yd) that could load 45-t (50-ton) end-dump trucks.

Jan 1, 1995

Manganese ore from the Black Rock, Kramer, and Black Jack mines in Tooele and Jaub Counties, Utah, are of acceptable grade, the U. S. Bureau of Mines has announced. Payment of a premium price of 252¢ per lb to the Copper Range Co., of Michigan for the output of its White Pine mine, has been agreed to by the DMPA. The contract will be limited to $28.6 million worth of copper. The agreement follows an RFC loan grant of $57 million to bring the White Pine property into production within three years. Increases of 5 to 6 cents over the Lake copper ceilings have been granted to the Calumet & Helca Consolidated Copper Co., for operation of "high cost" deposits, according to Jess Larson, DMPA administrator. Mr. Larson expects the move to add about one million lb of copper per month to the supply. The agreement can be cancelled on 60 days notice and is terminated automatically in the event copper ceilings are removed.

Jan 1, 1952

By Tom Szaraz, Steve Skelhorn

Part of a major sewer expansion for the City of Columbus, Ohio. The Big Walnut Outfall Augmentation Sewer (BWOAS) consists of 4,000m (13,200 ft) of 3.66m (12 ft)diameter tunnel passing mainly through glacial deposits with a water head of up to 2 bar. The project involves many new innovations, including: Slurry wall work shaft with excavation below the water table; Hybrid universal rings combining traditional steel reinforcement with fibers; New, full EPB Lovat TBM; Two component grout system pumped to the TBM from the surface; and, Linabond corrosion protection liner. The paper looks at the planning approach adopted to meet the various challenges presented, combined with an overview of progress to date.

Jan 1, 2007

By Charles W. Goodale, William A. Akers

The treatment of silver-ores of too low a grade to justify either smelting or preliminary roasting, and yet not " free" enough to permit of raw amalgamation, has ever been a serious problem. As bearing upon it, the operations of the Combination Mining and Milling Company of Black Pine, Deer Lodge county, Montana, during the past year may not be without interest. It is not claimed that the process to be described is not susceptible of great improvement, nor is any claim of originality made for it; but its use is, as yet, not very general, and it seems to offer a means of profitably working the large class of partially-decomposed argentiferous ores which, by reason

Jan 1, 1890

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground nine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.8 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated. Rock dust was employed chiefly in the larger mines, which numbered only 431 out of 6,016 underground mines in operation in 1935, according to reports from mining companies. The mines in which rock dust was used had an average of 288 underground employees per mine, whereas mines in which rock dust was not used averaged only 62 underground employees per mine.

Jan 1, 1940

By W. W. Adams

Rock dust, as a preventive or limiting factor in explosions of gas and coal dust in bituminous-coal mines, was used in larger quantities in 1939 than in any other year except 1937 since annual figures first became available in 1930, Reports from mining companies to the Bureau of Mines revealed that 144,430,000 pounds of rock dust was applied to underground mine workings in mines that produced 126,635,677 short tons of coal during the year. This quantity of rock dust applied averaged 1.14 pounds for each ton of coal produced. Rock dusted mines were the source of 39.7 percent of the total production of bituminous coal from underground mines; 33.2 percent of the total number of underground workers were employed at rock-dusted mines, and 35.9 percent of the total number of man-hours worked underground at all bituminous-coal mines in the United States during 19719 can be accredited to mines so treated.

Jan 1, 1940

By Paolo Cavalcoli, Marco Ziller

"ABSTRACT: In the year 2010 the State of Denmark together with the Municipality of Copenhagen, launched a very important and complex Project : the complete construction of a new double Subway Line :the CITYRINGEN.Copenhagen is the capital with a metropolitan population of 1,9 million.This line is like a ring placed in the very town center which includes all the most historical and monumental buildings and churches, with a total length of 17 km, and the presence of 17 stations plus 4 service shafts.The buildings have been built in the last centuries in an area where the groundwater is near to the surface and there are lakes and channels: the techniques adopted were advanced for those times, but limited as far as regards settlements and resistance to horizontal movements.The soil consists in 2 main groups.1.Upper sediments of the glacial ages : thickness total = 5-20 m composed by clay- silt-sand-gravelcobbles- granite boulders and flint in blocs and in layers : frequency and size of these obstacles wherenot determined.2.Limestone layers : 2a. upper limestone : highly fractured ,highly permeable2b.Itermediate limestone : less fractured, medium permeability.2c. Lower limestone : almost not fractured, low permeability.2d Bryozoan limestone : composed by fossils with microscopic dimensionsIn all the limestone formations there are important layers of flint , having thickness variable up to 3 m and important extensions. Water : in a part of the areas of the Cityringen the water is drinkable and utilized in the public waternet.Pollution: there are polluted zones due to previous industrial activities. Benzene areas have been identified, and for those areas special protections against pollution have been implemented.METROSELSKABET ,the public owner of the Cityringen,has set as priority to operate for the construction of the Cityringen the full protection of the environment and the respect of all the stakeholders :Very strong limits for the exhausted gas emissions have been introduced, by far stronger than those applied from the State of Denmark, very strong limits for the acceptable noise emission. And last but not least very important safety measures and procedure to avoid any accident on site."

Jan 1, 2014

By Valentín Pamo Caytano

La electrorefinación en un electrolito de CuSO4 - H2SO4 es usado universalmente para producir cobre de alta pureza a partir de los ánodos impuros. Aunque una parte de las impurezas se disuelve durante la electrorrefinación y se concentra en el electrolito, otros elementos son insolubles y se acumulan como lodos anódicos en las celdas de refinación. Las impurezas deben ser removidas del cobre para cumplir las especificaciones del mercado sobre la ductibilidad y conductividad y para recuperar los sub-productos valiosos como el oro y la plata. En ese sentido, el presente trabajo describe los equipos y procesos que permiten la recuperación del oro refinado en la planta de metales preciosos de la Refinaría de cobre de Ilo.

Sep 12, 2011

By Kay E. Goldberg

The Bureau of Mines conducted a study to develop and evaluate a training workshop for mine safety training personnel. The workshop was based on the Instructional Development Institute (IDI) which has been used for nearly ten years to train educators and administrators in the application of a nine-step model for defining, developing, and evaluating instruction. The Mining Instructional Development Institute (MIDI) was developed by investigators at the University of Southern California as a two-phase project. Phase I involved the modification of the six-day IDI program (including audiovisual presentations, workbooks, games, and exercises) for use by mine safety trainers as a workshop lasting three and one-half days. Phase II involved the evaluation and validation of the prototype MIDI workshop by means of a two-stage jury of experts and a prototype field trial. On the basis of data collected in the validation process it was determined that the institute provided an effective and useful method of instruction in mine safety training and that the institute would be especially valuable for mine safety training administrators and supervisors.

Jan 1, 1980

By Tell Ertl

TODAY'S mining industry is witnessing a transition in labor utilization. The drill-jumbo operator, the mucking-machine operator, the blasting crew, the scaling and timbering crew are all specialists. The all-around miner is rapidly disappearing. As mechanization has resulted in a higher order of underground skills; specialization of labor has been a natural consequence, as has the need for more supervision and engineering. Mines now are cleaner, neater, safer, and have a greater productivity per man-shift than ever before. Nothing spectacular like the continuous miner has yet come to the underground metal mines, but t a gradual improvement in methods, equipment, and technical knowledge is achieving the increased efficiency. With the exhaustion of the rich ores and large profits and who-cares-about-the-costs, mining has become a business; that of producing low value ores at costs below selling price. Charles A. Chase, patriarch of Colorado mountain mining men, manager of the Shenandoah-Dives, was one of the first to preach and prove his preachings that mining is a business. He has been mining a lead-copper-zinc-gold-silver ore, much from elevations above 1.3,000 ft, for a quarter century without a shutdown.-The ore is of such low value that most engineers and investors still would consider it foolhardy. Yet he has kept Silverton, Colo., alive, has paid wages without a lapse, has produced $25 million of new wealth and maintained a steady return to the investors. This type of responsibility is increasingly apparent in the mining business and is one feather that can be worn proudly. .Much emphasis is being placed on improving, the productive mining operations-breaking, loading and transportation. Breaking in underground metal mining is done by drilling and blasting. To the writer's knowledge, no chain or rotary-type machine has been developed for mining strong, abrasive rock. Drilling Percussion drills are still the standard drilling machines underground. Diamond drills, that: were the rage a decade ago for drilling long holes, are being superseded by the rock drill. The development of the hard abrasion-resistant carbide bit permits full-gage long holes to be drilled by percussion drills at a lower cost than diamonds. The change in the use of percussion drills is chiefly in the method of mounting. The column and arm are disappearing and the jackleg and rubber-tired or track-layer jumbo mountings are taking its place. At the Homestake mine .lightweight jackhammers mounted• on pneumatic legs using 7/8-in. hexagonal drill. rods and 1 1/2-in, tungsten-carbide detachable bits have been found more portable and maneuverable. They have less air consumption, lowered, dynamite consumption, and more footage and tonnage per man-shift than with 3 1/2-in. drifters on a column mounting. Drills now are mounted on longer feed carriages, drilling up to 20 ft without changing steel. These mountings result in great savings because the driller can set up quickly, drill the entire depth of the hole without changing the drill rod or bit using carbide and one-use bits, and can move his machine quickly to the next hole. One man to the machine is becoming general practice. The result is longer rounds rounds drilled at a lower cost than the previously used short rounds. A jumbo developed in the Tri-State can be extended to mine ore left in the roof up to 65 ft above the floor. Drill-rod life was formerly considered to be about 250 min of actual use. The increase in the drilling time per rod per day has gone up considerably with the development of the jumbo and the long-feed carriage, resulting in which is apparently more rod breakage., Consequently, a great deal of research is being done in the attempt to develop an alloy-steel rod with longer service life to offset the greater cost. Some reports indicate that alloy steel or Swedish steel results in cheaper drilling than conventional drill rod. However, several tests have shown only slightly increased life for alloy drill rod. Undoubtedly, the blow of the rock drill, the length of the drill rod, and the resiliency of the rock being drilled are important factors in the life of drill rod, so it follows that alloy steel might work well in some mines and result in no savings in others. The bit forged on the drill rod is seldom encountered and steel detachable bits are not as common as in the recent past. The one-use bit is gaining popularity because of. the difficulty in rehardening reconditioned steel bits satisfactorily. It is thought that the, carbie-insert bit is most applicable to drilling hard 'rock' where the steel bit is unable to drill out a full change, for instance, in extremely abrasive

Jan 1, 1952

Polyacrylamide flocculating agent has been used in the Leaching Division 'of the Risdon Works of the Electrolytic Zinc Company of Australasia Limited since October, 1960. The number of thickeners in the continuous thickening stage was thereby reduced from eight to three. There has been an increase of 25 per cent in throughput and a reduction of solids in thickener over-flow from 3-4 g/l. solids to 0·5 g Ir. solids. Reagent addition has been at the rate of 0·25 lb Separan NP10 per ton solids.Additionally there has been a gain of 3 per cent in current efficiency as the direct result of the addition of Separan NP10 to purified cadmium sulphate solution priOl; to electrolysis for cadmium metal. A smoother deposit has resulted and it has been possible to increase deposition time between strippings from 47 to 71 hr. However, there has been a slight increase in the lead content of the cadmium metal produced.The use of Separan NP10 to settle copper bearing residue in a batch process stage has resulted in a five-fold increase in settlement rate and a reduction in purification cycle time.INTRODUCTIONThe Electrolytic Zinc Company of Australasia Limited, Risdon, Tasmania, produces zinc by electrolysis of purified zinc sulphate solution, the raw material being zinc sulphide concentrate. In the Risdon process (Van Arsdale, 1953; J ohnstone, 1953; Ross, 1949) the compound zinc ferrite (ZnO.Fe203) is formed during the concentrate roasting stage. When the roasted material is leached in dilute sulphuric acid the zinc ferrite is not attacked, and it remains as part of the insoluble leach residue, of which it may form as much as two-thirds of the whole. The remainder is mainly unroasted zinc sulphide, unleached zinc oxide, lead sulphate, gypsum, silver compounds etc. The zinc in the residue may be 10 per cent of that in the original concentrate.Continuous thickeners are used to recover the valuable residue from the impure zinc sulphate solution and the...

Jan 1, 1963