Search Documents

By F. A. Rutledge

The Millet copper deposit is on the north shore of Iliamna Lake in southwestern Alaska. Copper mineralization occurs in a zone of altered limestone .adjacent to and intruded by a diorite porphyry with some diabase facies. During 1949 and 1950, the Bureau of Mines investigated this prospect as a part of the U. S. Department of the Interior program in Alaska for the development of critical and strategic minerals. Field work was begun August 8, 1949; it was recessed November 28, 1949, because of inclement weather. The work was resumed Nay 28, 1950, and completed July 3, 1950. The program of investigation by the Bureau of Nines included topographic surveying, machine and hand trenching, diamond drilling, and sampling the zones of mineralization. This report outlines the general geology of the area, gives a description of the deposit, and contains the factual data resulting from work by the Bureau of Mines.

Jan 1, 1952

By R. A. Marriot

The steam-generating plant at the Garfield smelter of The American Smelting and Refining Co. consists of two divisions in which the boilers are classed as direct-fired or waste-heat. The direct-fired boiler plant consists of eight 330-boiler hp. type K-19 and S-I 7 Stirling boilers located in the boiler room adjacent to the power house, and two 330-boiler hp. Stirling type K-19 boilers in the reverberatory building, which formerly were connected to a reverberatory furnace but now are arranged for direct firing. All direct-fired boilers are now fired with natural gas. The waste-heat boiler plant consists of all units connected to reverberatory furnaces, and receiving heat from the exit gases therefrom. In this classification there are two 490-boiler hp. Erie City vertical water-tube boilers, and six 330-boiler hp. type K-19 Stirling water-tube waste-heat boilers. Each furnace has boilers arranged in battery setting. The boilers are directly in front of the furnace and connection is made through a short uptake and flue (Fig. 1). The Stirling boiler settings rest on concrete foundations at ground level, with the furnace uptake and flue at a low elevation. The Erie boilers are carried on steelwork some 15 ft. above ground level, and stand against the face of the uptake with no connecting flue. The constructional requirements of a larger furnace dictated this type of setting.

Jan 1, 1934

By Robert E. Green, T. Hinton

The velocities of the three possible modes of elastic-wave Propagation have been calculated for single-crystal aluminum at 1-deg intervals throughout the standard steveographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy propagation and specirzen axes are presented as arrows drawn within the standard triangle. The orientation factors associated with dislocation nzotion on the primary slip system only and also on all twelve slip systenzs have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing--7aue resonant specivnen hazle also been calculated. The relevance of these results to ultrasonic attenuation measurements is discussed. DUE to the widespread use of ultrasonics in the investigation of the properties of solids a number of authors15 have discussed in detail the theory of elastic-wave propagation in solids. In this paper the modes of wave propagation are evaluated according to the procedure suggested by reeen' for the case of single-crystal aluminum at 1-deg intervals throughout the standard stereographic triangle. The wave speeds are presented in the form of contour diagrams within the standard triangle. The deviations between the direction of maximum energy propagation and the normals to the wave fronts are presented as arrows drawn within the standard triangle. The orientation-de pendent factors (orientation factors) associated with dislocation damping as derived in the preceding paper6 have been calculated for the case of aluminum at 1-deg intervals throughout the standard triangle. The orientation factors for dislocation motion on the primary slip system only and on all twelve slip systems are presented in the form of contour diagrams, for both the traveling- and the standing-wave conditions. The relevance of these results to ultrasonic attenuation measurements is discussed. ELASTIC-WAVE PROPAGATION Three waves can be propagated in a linear elastic homogeneous anisotropic medium. The velocity of propagation v of each of these waves in a medium of density p can be obtained from the determination of the eigenvalues and eigenvectors of the matrix equa- The A's are a series of moduli which are functions of the elastic constants cij and the direction cosines 1, m, and n of the specimen axis. In the case of cubic single crystals where there are only three nonzero elastic constants cll, c12, and C, the A's are, The solution of Eq. [I] will give the wave speeds (eigenvalues) and the direction cosines a, 0, and y of the particle displacements (eigenvectors). To obtain the direction of maximum energy flux requires the calculation of the energy-flux vector ET with com- w is the angular frequency, A, the amplitude, and v the velocity of the wave. The direction cosines a, b, and c of the energy flux vector are then given by

Jan 1, 1967

By Maurice B. Dusseault, Edo Nyland

Numerous consistent seismic signals are being generated in a pilot fireflood in a 750 m deep high permeability unconsolidated channel sand in Eastern Alberta. The pilot has a central air injection well, eight production wells on artificial lift, and two internally placed observation wells. Surface seismometers and a 12-hydrophone downhole string were deployed to detect seismics signals. Date were collected for 22 hours employing signal-triggered event detectors recording on cassette tapes. Monitoring during twelve hours of steady air injection at 625m3/s yielded a clear event frequency of about 50 events/h. The events were mostly clear compressional wave arrivals originating in the vicinity of the firefront. Stopping air injection caused a gradual drop in event frequency, and the rate was reestablished when air injection was reinitiated. Spectral frequency analysis and knowledge of material properties indicate that the events are shears of a stick-slip nature associated with the strain-weakening behavior of the over-compacted reservoir sands. The event amplitude indicates small-scale shearing, and different amplitudes suggest that planes re-shear with lower energy release levels. The triggering mechanism for shear rupture is high shear stress created by thermal expansion in the area of highest ther- mal gradient. Other enhanced recovery techniques may also produce useful signals for process control. In particular, steam flooding, hydraulic fracturing, and high-pressure injection operations likely generate mappable microseismic events which can be applied directly to production/ injection strategy.

Jan 1, 1982

By Richard Stoltz, Gary Smith

This paper presents the findings of a face ventilation investigation, conducted by the Ventilation Division, Pittsburgh Health Technology Center, at a underground coal mine operating in the Illinois No. 5 coal seam. The purpose of the investigation was to evaluate the effectiveness of a blowing face ventilation system in controlling methane liberation in the face area while mining with brattice distances up to a maximum of 40 feet from the face (extended cut). The continuous miner on this section was remotely controlled and equipped with a machine mounted dust collector. Data collected during this investigation included methane concentrations, intake and return air quantities in the face area, and scrubber air quantities. In addition, a time study was conducted to correlate the methane peaks to activities in the face area. In conjunction with the face study on Section A, separate methane liberation studies were conducted on three additional sections: B, C, and D. This was done in order to compare intake methane concentrations and methane liberations from other sections in the mine to the test section. Calculations indicated that the minimum intake air quantity necessary at the inby end of the line brattice for the section investigated was 7,000 cfm. Due to the higher intake methane concentrations and average methane face liberations measured on three other sections, the minimum air quantities necessary at the inby end of the line brattice were determined to be 13,900 cfm, 11,100 cfm, and 15,000 cfm, respectively.

Jan 1, 1991

By T. R. Cass, M. R. Achter

A technique for measuring the creep and rupture strength of nickel specimens bonded by sintered oxide layers has been developed for the investigation of the role of grain-boundary oxide in the oxidation strengthening of nickel during creep at 817 °C. Prom the inverse dependence of the rate of bonding on the thickness of the starting oxide, it is suggested that the rate of diffusion of Ni++ through NiO is the controlling process at the start of sintering. Cornparisons of the creep and rupture strength and of the microstructure of sintered couples with conventionul creep specimens suggest rupture in nickel is prevented by load-bearikzg, ikltergranular layers of oxide. A number of recent investigations have shown that at high temperature and low stress the creep-rupture strength of nickel and nickel-base alloys may be much greater in air than in an inert gas or vacuum.'-7 For example, at 817°C and 2500 psi, nickep failed in vacuum in 48 hr but not in air after 4000 hr, and a Ni-Cr-A1 alloy5 at 1038°C and 3000 psi failed in vacuum in 4 hr but not in air after 731 hr. Fig. 1 is a typical creep curve in air for materials experiencing this pronounced environmental strengthening. A common feature of these curves is the entry into a third stage of accelerating creep, concurrent with the for-

Jan 1, 1962

By R. V. Ramani, S. Skankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken: •a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; •a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and •the mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies, it was observed that increasing the air velocity increased the rate of re-entrainment (Shankar and Ramani, 1994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1996

By W. R. Reed, J. A. Organiscak

Surface mining operations use large off-road haul trucks extensively to move material at mining properties. Past research, using the United States Environmental Protection Agency’s (EPA) emissions factors for unpaved haul roads, has shown that haul trucks generate the majority of dust emissions from surface mining sites, accounting for approximately 78%-97% of total dust emissions. Observations of dust emissions from haul trucks show that if the dust emissions are uncontrolled, they can be a safety hazard by impairing the operator’s visibility. This increases the probability for haul truck accidents (See photos above). However, the greatest long-term health hazard of dust generated from hauling operations is due to inhalation of the respirable dust [median diameter <4 micrometers (µm)] and tho­racic dust, which is equivalent to the EPA’s definition of PM10 [particulate matter with a median diameter <10 µm]. Exposure to respirable dust has long been considered a health hazard at surface mining operations, especially if silica dust is present. There are two legislative acts that regulate the air quality for mining operations: the Federal Coal Mine Health and Safety Act of 1969 and the Clean Air Act of 1970. The Federal Coal Mine Health and Safety Act of 1969 established the limits for dust in the work place for health and safety pur­poses. The Clean Air Act of 1970 regulates air emissions from facilities from an envi­ronmental perspective.

By Christopher J. Hall

It has been known for a long time that summing pressure drops and rises due to friction, shock, fans and natural ventilation is incorrect. In fact, lost works and works should be summed. In spite of this, the traditional method of finding a fan/system operating position has been the H/Q Curve. This paper presents (lost) work/m curves, progressing from a single fan moved around the system to include natural ventilation work, and fans in a series, parallel and series/parallel. The solutions obtained graphically are substantiated by dry air thermodynamic solutions, and the traditional solutions are shown to be in error. This method of solving problems is particularly useful when moving fans around the system, and essential in series/parallel and series situations with substantially different fan densities. The dry air analysis is employed because of its simplicity. Real air, with evaporation and condensation, will react somewhat differently, and one should use real densities (i.e.[l + w +w]/va ) when using this method. One source of error when applying this method to real air, although probably not major, will be investigated in a subsequent paper. Friction and shock losses are proportional to the square of the mass rate of flow, leading to the typical parabolic system curve. However, the unbalanced water stuff potential energy term, on a unit mass basis, is substantially independent of the mass rate of flow. It is possible that this could be handled as a negative natural ventilation work.

Jan 1, 1987

By Thomas M. Dr. Drown

IN experimenting in connection with Mr. P. W. Shimer (now chemist of the Thomas Iron Company, Hokendauqua, Pa.) on methods for the determination of silicon in pig iron, in order to find one which should be accurate and yet give results in a few hours, I have adopted the following procedure, which, as far as my experience goes, leaves nothing to be desired. About one gram of pig iron or steel is treated in a platinum or porcelain dish with 25 cubic centimeters of nitric acid (sp. gr. 1, 2). When action has ceased, 25 to 30 cubic centimeters of dilute sulphuric acid (one of acid and three of water) are added, and heat applied until the nitric acid is nearly or quite driven off. The heat of a water-bath is sufficient, though the process may be hastened by heating higher on a sand-bath. Water is then cautiously added (as soon as the free sulphuric acid is sufficiently cool) and the contents of the dish heated until the crystals of ferric sulphate are completely dissolved. The solution is then filtered as hot as possible, the residue washed first with hot water, then with 25 to 30 cubic centimeters of hydrochloric acid (sp. gr. 1, 12), and finally with hot water. After drying and igniting, the silica will be found to be snow-white and granular. The following are some results obtained by this method compared

Jan 1, 1879

By Thomas M. Drown

In experimenting in connection with Mr. P. W. Shimer (now chemist of the Thomas Iron Company, Hokendauqua, Pa.) on methods for the determination of silicon in pig iron, in order to find one which should be accurate and yet give results in a few hours, I have adopted the following procedure, which, as far as my experience goes, leaves nothing to be desired. About one gram of pig iron or steel is treated in a platinum or porcelain dish with 25 cubic centimeters of nitric acid (sp. gr. 1, 2). When action has ceased, 25 to 30 cubic centimeters of dilute sulphuric acid (one of acid and three of water) are added, and heat applied until the nitric acid is nearly or quite driven off. The heat of a water-bath is sufficient, though the process may be hastened by heating higher on a sand-bath. Water is then cautiously added (as soon as the free sulphuric acid is sufficiently cool) and the contents of the dish heated until the crystals of ferric sulphate are completely dissolved. The solution is then filtered as hot as possible, the residue washed first with hot water, then with 25 to 30 cubic centimeters of hydrochloric acid (sp. gr. 1, 12), and finally with hot water. After drying and igniting, the silica will be found to be snow-white and granular. The following are some results obtained by this method compared

Jan 1, 1879

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

IN his paper on the calculation of hardenability from chemical composition, Grossmann1 discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability-arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium-and to extend the range of composition of some of the elements studied by , Grossmann-chromium, copper, manganese, molybdenum, nickel and silicon. EXPERIMENTAL METHODS To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the &apos; alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (2300°F.) , and forged into rounds of 1 ½ in. diameter. These bars were normalized twice from 840°C. (1550°F.) before machining into Jominy bars. The composition of the steels was deter- [ ] mined in most cases by samples taken from the end-quench hardenability specimen. As suggested by crafts,2acid-soluble

Jan 1, 1943

By Stewart L. Toleman, Robert H. Hafner, Irvin R. Kramer

In his paper on the calculation of harden-ability from chemical composition, Gross-mannl discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability—arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium—and to extend the range of composition of some of the elements studied by Grossmann—chromium, copper, manganese, molybdenum, nickel and silicon. Experimental Methods To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (23oo°F.) and forged into rounds of I½ -in. diameter. These bars were normalized twice from 840°C. (I55o°F.) before machining into Jominy bars. mined in most Cases by samples taken from the end-quench hardenability spedmen. AS suggested by Crafts,2 acid-soluble (8

Jan 1, 1944

By Robert H. Hafner, Irvin R. Kramer, Stewart L. Toleman

In his paper on the calculation of harden-ability from chemical composition, Gross-mannl discussed the effect of most of the alloying elements used commercially. The purpose of the work reported in this paper was to determine the effect of several other elements on hardenability—arsenic, antimony, beryllium, cobalt, columbium, germanium, tellurium, tin, aluminum, and titanium—and to extend the range of composition of some of the elements studied by Grossmann—chromium, copper, manganese, molybdenum, nickel and silicon. Experimental Methods To determine the effect on hardenability, suitable amounts of the alloying elements were added to experimental heats and the hardenability determined by means of end-quenched hardenability specimens. The steels were melted in a high-frequency induction furnace with a basic crucible, using ingot iron as a base for some of the heats and S.A.E. 1015 for others. The alloying additions were made as ferroalloys or as metal, depending on the alloying element. Hundred-pound heats were split and poured into square, tapered, cast-iron ingot molds with hot tops. Aluminum was not used as a deoxidizer in most of the heats. The ingots were homogenized for 12 hr. at 1260°C. (23oo°F.) and forged into rounds of I½ -in. diameter. These bars were normalized twice from 840°C. (I55o°F.) before machining into Jominy bars. mined in most Cases by samples taken from the end-quench hardenability spedmen. AS suggested by Crafts,2 acid-soluble (8

Jan 1, 1944

By Dale R. Ralston

This investigation was divided into two major phases. Phase I of the study was an examination of the occurrence and production of acid water within the Bunker Hill Mine in northern Idaho. The second phase of the project involved the study of water movement through an abandoned tailings pile. Mineralogy and hydrogeology were determined to be the two most important factors in the acid mine drainage problem. Low pH water was formed in the mine in areas of lead-zinc ore rich in pyrite. Water movement in the mine was important in the production of acid and the transportation of heavy metals. Areas of recharge to the mine were identified. A data collection network was installed to monitor water quality and quantity changes. The quantity of acid drainage from the mine was found to vary directly with surface runoff events. The study of the abandoned tailings pile was performed to determine the characteristics of water movement through the tailings material and the resultant impact on the hydrologic environment. The Page Tailings Pile, abandoned in 1969, was utilized as a study area. An extensive network of piezometers and meteorological data collection sites were installed in and near the pile. Data collected to date indicate the presence of a ground-water mound under the east half of the pile. Some transfer of ions from the tailings pile to the ground-water system has been detected.

Jan 1, 1973

By F. D. Rosi

IN the production of single crystals by the Bridg-man method of solidification from the melt in vacuum at a crucible lowering rate of 0.25 in. per hr, a cellular structure was frequently observed in copper and copper-base alloys at the terminal surface of the as-cast crystals (i.e., the surface representing the last portion of the crystal to solidify). The geometrical form of this structure varied from crystal to crystal, but, in general, could be classified as either hexagonal or quadrilateral. Fig. 1 shows examples of this cellular structure, which is similar to that reported by Buergerl and, more recently, by Pond and Kessler&apos; and Rutter and Chalmers. In the micrographs of Figs. lb and c, the cubic structure in the alloy crystals is obscured somewhat by excessive surface evaporation in the final stages of solidification. X-ray orientation studies indicate that the traces outlining the various geometrical forms correspond to octahedral planes, which are the planes of greatest reticular density in the face-centered cubic lattice. It would appear from this that the view first propounded by Bravais,4 that the surface energies and normal growth velocities of the different crystal planes are inversely proportional to their reticular densities, applies to this cellular structure, since those surviving are the planes of greatest atomic density. Thus, the observed variation in the geometrical form of this structure in crystals of different orientation is readily understandable from the distribution of the (111) planes in the standard {111}, (1101, and (1001 stereographic projections. Depending upon whether the crystal axis (i.e., the direction of crystallization) coincides with a <111>, <111>, or <100> direction, the cellular structure viewed from a surface perpendicular to the crystal axis will consist of a network of regular hexagons, skewed hexagons (with interfacial angles of 110" and 125"), or cubes, respectively. It follows, moreover, that off-orientations from these principal directions will yield modifications of these three basic geometric configurations. In this connection, it is interesting to note that the bounding planes of the hexagonal structure observed in tin by Rutter and Chalmers3 showed no preferred orientation.

Jan 1, 1954

By H. H. Otto

Fourteen years ago, J. B. Warriner presented before the Institute a paper on anthracite stripping,&apos; describing the progress of stripping in the Anthracite Region from its beginning with an old quarry stripping at Summit Hill, which was operated more than a century ago, through various types of strippings used in 1917. This paper will briefly review the status of anthracite stripping methods from 1917 to the present day and describe in detail the stripping operation of The Hudson Coal CO. at Clinton collicry. It is not intended as a review of the work in the district—that would require a much longer paper. History and Statistics Mr. Warriner said, in part: "The sizes of shovels have gradually increased until now 70 and 80-ton shovels are the rule and larger equipment is coming in." He also referred to a large electrically operated dragline which weighed about 225 tons and had an operating radius of 125 ft. In 1917, a number of strippings used shovels of various sizes, ranging up to the 60 Marion and Bucyrus 70-C railroad type. Material was hauled away in narrow-gage side dumpers, usually of 4 or 5 cu. yd. capacities. Star-type churn drills with 4-in. bits were generally used for drilling purposes. Since 1917 wages in the anthracite field; have increased, but the higher operating costs of strippings are now being successfully combated by continuous improvements in stripping equipment, such as the development of the caterpillar or crawler shovels, the use of larger cars, better drilling equipment, the introduction of shovels of increased capacity and the adoption, in a number of instances, of standard-gage equipment for transportation. In 1918 another large dragline was introduced in the southern fields, which had been in service in the Middle West and is in use today, dipping vertically about 180 ft. to raise coal out of a stripping. About 1918, small shovels with caterpillar traction were introduced. In 1922 the 6-in. well drills began replacing the 4-in. drills, with an attendant saving to the operators. About the same time A. E. Dick placed the first pair

Jan 1, 1931

By C. R. Austin

THE investigation described in this paper deals with the development of high-temperature alloys of the Konel series over a considerable period of time at the Research Laboratories of the Westinghouse Electric and Manufacturing Co. The word "Konel" has been coined to designate a class of alloys which are essentially nickel-cobalt-iron with other elements added, usually in small quantities. Most of these alloys contain titanium, usually about 2.5 percent. The main consideration related to strength at high temperatures but the thermionic characteristics of the alloys was also of considerable importance. It is, however, with the mechanical properties at elevated temperatures that we are herein concerned. Much attention has also been devoted to their age-hardening characteristics. There is little need to stress the utilitarian aspect of this subject, as it has been discussed frequently. Alloys exhibiting superior properties at normal or elevated temperatures rapidly find many suitable applications. There may be some question, however, as to what constitutes a "superior alloy, " or an alloy that may have good service possibilities at high temperatures. The problem is complex and various means have been employed to predict the useful life that may be expected of a material. In recent years the "creep limit" has been used as the best means of evaluation. Such tests necessarily are prolonged and hence collection of data is very slow. In a general survey of many alloys therefore the creep test is not desirable and recourse must be had to much shorter time tests in order more rapidly to select alloys which appear to show promise. For this reason the present survey has been made using the high-temperature tensile test and a bend&apos; test developed by Howard Scott.1 In the tensile test the conditions have been standardized for all tests, so that values obtained are at least comparable, one alloy with another, although the absolute values recorded merely indicate the mechanical properties at the given temperature under a definite rate of loading.

Jan 1, 1931

By Charles H. Behre

UNDER the caption "fault," geologists intend to include all mass movements of solid rocks over adjacent rock masses. When these are studied long after their origin, however, circumstances make it possible to recognize as "fault" only formations showing clear evidence of actual movement of one side with respect to the other. Necessarily the chief evidence consists of the offset of a vein, bed, or other key structure. Planes of movement parallel to the bedding, or nearly so, are recognized with difficulty or are overlooked and hence many important faults are wholly unrecorded. Indeed, among standard American references on structural geology, one alone emphasizes the importance of bedding-plane movements and that one only briefly1. For some time the writer, cognizant of this difficulty, has paid special attention to such movements, both as observed in the field and as recorded in the literature. It is believed that enough data are now at hand to justify a short discussion. Its purposes are fivefold. It is desired first to briefly classify and describe at least the more common kinds of bedding-plane faults, and second, to examine the causes and manner of their formation, at least in instances where the subject has not yet been well covered by other investigators. Third, certain by-products of bedding- lane movements are of such conspicuous importance to the economic geologist and mining engineer as to merit mention. Fourth, concrete illustrations should be placed before the reader in order to lend reality and to furnish a basis of comparison with his experience; such illustrations will necessarily be scattered through the text of this paper. They are only in part from the writer&apos;s own field observations. The fifth and prime objective of this paper is to direct attention to the great importance of movements on the bedding planes, in the hope that the recognition of such movements and their significance may simplify mining problems.

Jan 1, 1937

Tunnel damage from explosion and earthquake excitation is correlated with strain and particle motions. Critical strains and motions are then correlated with focal distance, which is so small that permanent strains are highly likely. The shaking process is then numerically modeled to investigate the effects of excitation frequency and joint orientation. The models confirm that near cavern blocks slide intermittently only at relatively high particle velocities during periods of low joint normal stress. Larger displacements occur with relatively small shear wave lengths or relatively high frequencies. Variation in joint orientation and rock mass dilation result in changes in displacement.

Jan 1, 1985