Search Documents

Discussion of the paper of Norman B. Braly, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1881 to 1906. GEORGE A. PACKARD, Butte, Mont.:-I would like to ask Mr. Braly if he has any information as to the relative efficiency of the sinking pump, using it as he refers to it, discharging the exhaust into the water column or otherwise. MR. BRALY :-I have never gathered any information on that point. It is a question of getting the work done. In driving the shaft, using that method, we find it easier on the men and everything else. In the bottom of the shaft, if you exhaust back into your column, it is a quiet. shaft. Another thing is the freezing: if you are sinking with air in your pump, you will find it is liable to freeze, and in that case as the air is still under compression it will not freeze the pump. The difference is very small if there is any. But, as might be expected, the pump is a little less efficient when exhausting the air into the column. MR. PACKARD :-I suppose all of us know what a pump in the bottom of the shaft is. My experience has been, although I have no figures, that the capacity of a pump is quite considerably decreased if you are pumping, say, from a depth of 200 ft. through a No. 7 Knowles pump, when you exhaust the air into a column, but, on the other hand, it is also my impression that we can raise the water to a little greater distance. I would like to get some figures from somebody who has made actual tests.

Jan 11, 1913

By M. E. Bell

The term "operational research" was probably first used to describe work started under E. C. Williams, now Director, SHAPE Air Defense Technical Center, late in 1937 or 1938, at the Bawdsey Research Station of the British Air Ministry, a laboratory center concerned with the development of radar equipment. After the practicability of the early techniques had been demonstrated, a large (for those days) program of development and installation was authorized. It was very soon realized, both by the Royal Air Force and by the scientists that almost as important as the gear itself was the way in which it should be used. Accordingly, it was decided that some scientists should cooperate to study the way in which the equipment should be deployed and operated in conjunction with the Royal Air Force. To distinguish this work from the normal work of a research and development establishment, the term "operational research" was coined. It merely meant at this time that this particular section of scientists was to be concerned with the use of the gear rather than with its technical development and it seemed natural to those concerned to adopt the word "operations" which has a specific connotation in the armed forces.' This method was later extended to peacetime business enterprise, government operations and other human activities. Operations research appears to have penetrated the extractive industries more slowly and less completely than other industries, the military, or the government. This may be due (1) to a difference in the attitude of management towards operations research, or towards research of any kind, for that matter; (2) to unsuitability of the extractive industries for application of the operations research method; (3) to inaccessibility of the data; (4) or to a lack of trained personnel who are interested in applying operations research to the mineral industries.

Jan 8, 1963

By K. L. Williamson, P. W. Dugan

INTRODUCTION In recent years there has been increased social awareness and government attention directed toward the mining industry. The growing influence of the Occupational Safety and Health Administration (OSHA), the Mine Safety and Health Administration (MSHA), and the Environmental Protection Agency (EPA) has resulted in volumes of regulations governing a multitude of health and safety aspects of mining and milling. These regulations naturally have had an impact on new plant design and in some cases have necessitated retrofitting of existing plants. This paper will not examine the regulations governing the industry, since they are a matter of public record, but rather will address two specific health considerations, dust and noise, and their influence on the design of crushing and screening plants. DUST AND NOISE CONCEPTS Dust is generally defined as finely divided solids which may become airborne without any physical or chemical change except fracture. Since the purpose of comminution circuits is to reduce the size of solids by fracture, a percentage of the material is normally reduced in size to a point where it can easily become airborne. The major cause of dust becoming airborne is the air induced by falling material. When granular material falls through a distance, the induced (or entrapped) air rushes out available openings, carrying with it the fine particles that have become suspended. For this reason, the major points of dust generation are the points where the material is falling: chutes, transfer points, screens and equipment feed and discharge points. The expected dust concentration in an area is a function of the degree of size reduction (i.e., finer particles are more readily carried by air currents than heavier particles) and the volume of air that is induced. The measured dust concentration values for various operations agree with this

Jan 1, 1982

By J. Linhart

In vertical airways, falling material - solids-or water - may cause undesirable disturbances in the ventilation in the airway itself and also in neig¬bouring airways unless precautions are taken to stabilize the air flow. Such cases can occur, for example, - in shaft sinking by drilling from a pilot hole, - during the filling up of shafts, and - during the introduction of water into shafts in the case of mine fires. In an airway with upward ventilation the falling material will reduce the air flow and may even re¬verse its direction. In an airway with downward ventilation the air flow can only increase, but a reversal of the direction of ventilation may result in a parallel airway. These disturbances in the normal ventilation are undesirable as it must be the aim to have ventilation that is stable in quantity and direction throughout a mine. In order to be able to prepare suitable stabilization measures one must know the pressure generated by the falling material; this pressure will henceforth be called "aeromotive" pressure. The main factors determining the influence of falling material on the ventilation are - the amount of falling material and its height of fall, - the cross sectional area of the airway, - the pressure. difference prevailing in it, - the-position of the. airway in the ventilation. network, - the air velocity, and - other parameters, e. g. the density and grain size of the falling material. To determine the aeromotive pressure-measurements have been made underground during the sinking and filling of shafts and systematic studies have been carried out during the supply of water into a staple shaft. The present paper deals first with some fundamental theoretical considerations and then describes the measuring arrangements and the results of the series of experiments that have been carried out.

Jan 1, 1980

By T. B. Crowe

MucH has been written upon the precipitation of metals from cyanide Solution by zinc. We often read of the many factors that influence precipitation, such as zinc surface, purity of zinc, percentage of lead, temperature of solutions, strength of solutions in cyanide or alkali, etc. -Little do, we hear, however, of the part that oxygen plays in precipitation. Caldecottl says: "As the dissolving of gold is essentially an oxidation process, so its precipitation is one of reduction." All who have studied or worked with cyanide solutions will agree that Caldecott's statement is true.' . In the cyanide work in the mills of the Portland Gold Mining Co., we have always found oxygen to be the greatest enemy to precipitation. Oxygen Antagonistic to Good Precipitation A few years ago, while making some experiments on the effect of pressure upon the dissolving rate of gold from our ores, to prove a point, I made some bottle tests under vacuum. The results were surprising, and showed that under vacuum practically no gold dissolved, which confirmed my belief that Elsner's equation was true and also led me to investigate the amount of dissolved air carried by solutions at atmospheric pressure. The experiment consisted in partly filling an acid-bottle with mill-solution and connecting it by a rubber hose to a vacuum pump. When the vacuum was suddenly applied, a cloud composed of thousands of small air bubbles rose out of the solution, showing qualitatvcily' the amount of dissolved air that was contained in the solution, and also proving that the relief of atmospheric pressure on the solution permitted this dissolved air to escape. In studying literature on the subject, we find Henry's law—"The amount of gas dissolved by a liquid is proportional to the pressure to which the gas is subjected."

Jan 1, 1919

By A. S. Richardson

Ventilation of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase* in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently. Facilitating Flow of Am As a basic requirement for the safety of the mcn, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft; is available as a base

Jan 1, 1940

To develop a quick, safe, and effective method that allows workers at mineral processing operations to clean their dust-soiled clothing periodically throughout the workday. Background Reducing workers' respirable dust exposure to silica and other harmful dusts and contaminants is an ongoing goal in the U.S. mining industry. One area of known worker exposure is from contaminated work clothes. A U.S. Bureau of Mines report documented a number of cases where a tenfold increase in a worker's dust exposure was measured from contaminated work clothes. In these cases, the dust emitted from clothing caused the worker's dust exposure to exceed the permissible exposure limit in less than 2 hours. The most effective way to eliminate this dust source is to have workers clean or change their work clothes. There are two federal regulations that impact the clothes-cleaning process. The first states that at no time shall compressed air be directed toward a person, but that when compressed air is used, then all necessary precautions shall be taken to protect persons from injury. The second regulation states that compressed air should only be used for cleaning purposes when it is less than 30 psi and used along with personal protective equipment. For the mining industry, by default, the only approved method to perform clothes cleaning is to have workers vacuum their clothes using a HEPA filter system. This is very difficult and time-consuming and, in most instances, not very effective. Most workers would prefer to use a single compressed air hose to blow dust from their work clothes. However, not only is this method prohibited by law, it usually creates a significant dust cloud in the work environment and contaminates coworkers.

May 1, 2005

By A. S. Richardson

Ventilation of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase* in mining depth, higher rock temperatures have been encountered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together with dust sampling and related microscopic work for the quantitation of the dust samples and determination of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently. Facilitating Flow of Am As a basic requirement for the safety of the mcn, all ventilation plans are subject to a ruling that the main operating shafts must be maintained as inlet air courses. Under this condition, a safe, fresh-air escapeway is assured if a fire occurs within the mine, and the shaft; is available as a base

Jan 1, 1940

By E. Posnjak

IT is rather the general belief that acidified, solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as. cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by passing air for 3 hr.. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will bee proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2 His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 12, 1926

By E. D. Gardener, Byron O. Pichard

"Methane, frequently called fire damp or marsh gas, is very well known to coal miners but to thy average gold miner it means nothing, as it is not associated generally with the rock formations in which gold is found.We have recently been conducting a study of mine air in typical gold mines on the Pacific Coast, and out of five California mines in which the air was sampled, three showed methane. Each of these three mines, referred to below as mines A, B, and C, have had accumulations great enough to be ignited. An authentic report from another California, gold mine, which has not yet been sampled, states that recently the superintendent was seriously burned by the ignition of a pocket of gas. This mine is later mentioned as mine D.Mine A is an old mine which had been abandoned for several years and permitted to fill with water. It has been unwaterad recently, and is now being developed at greater depths. During the unwatering, gas bubbles formed on the water and upon being ignited burned freely. It is reported that two men were seriously burned from accidentally igniting the gas. Samples of the bubbles on analysis showed high percentages of methane. Since the mine has been unwatered, no trouble has been experienced through gas being ignited. However, out of a total of six air samples which we took recently in scattered working places, all showed small amounts of methane, the methane content being 0.06, 0.04, 0.05, 0.04, 0.04 and 0.07 per cent, respectively. When these samples were taken methane was not suspected, but its general presence in the mine air indicates that it is being given off constantly."

Dec 1, 1921

By E. Posnjak

IT is rather the general belief that acidified solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no. oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by, passing air for 3 hr. through solutions of Mohr's salt acidified with sulfuric acid." While this statement will be proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2. His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 1, 1927

By N. V. Melnikov, L. N. Marchenko

The latest theoretical and experimental study of physical processes initiated by explosions in solid media have made it possible to obtain a deeper insight into the mechanism of the energy transfer to ambient rock from char es of explosives interspersed with various air gaps. As shown in (17, high explosive action causes excessive fragmentation of medium in the vicinity of the charge, while expansion of the process into the massif is negligible. A theoretical outline of a more rational application of explosion energy was given with a view of obtaining more uniform fragmentation of rock convenient for loading and transportation. The proposed idea proven by experimental study consisted of the possibility of explosion control based on redistribution of explosion energy. Practical realization of the above idea was proposed (1) involving charges with air gaps for rock fragmentation. Since the Rolla Symposium on Mining Research (USA, 1961) (2), borehole charges with air gaps have become common practice. This method of rock blasting is applied in open cast and underground mines working the hardest and viscous, hard, medium hard and soft rocks (ore, quartzites, granites, 1 imes tones, sandstones, coals, etc.) as well as at enterprises for extraction of building materials and raw chemical minerals of any strength. Application of charges with air gaps results in an increase of the degree and uniformity of fragmentation (up to 94 percent of the blasted rock mass consists of fragments not exceeding 400 mm), the average fragment size decreases by 1.5-2 times and the amount of lumps is reduced by 2-10 times (in some cases there are no lumps at all ). Besides, the amount of operation for filling boreholes with tamping material is reduced, the specific consumption of explosives

Jan 1, 1971

By W. P. Sykes

IN CONNECTION with a study of tungsten steels, Honda and Murakami1 reported an investigation of the system iron-tungsten. This report included a tentative equilibrium diagram, photomicrographs of various alloys in the series, and qualitative measurements of hardness and magnetic properties. The present investigation originally had as its object the study of the hardness and tensile properties of a series of carbon-free iron-tungsten alloys. But, as the work progressed it became evident that the system possessed other features of interest, so the scope of the investigation was enlarged. MATERIALS The iron powder used in preparing the alloys was obtained as follows: Iron oxalate was precipitated from a ferrous-sulfate solution by the addition of a solution of oxalic acid. This oxalate, after thorough washing, was ignited to iron oxide, which after reduction in hydrogen at about 1000° C. yielded iron powder containing but about 0.2 per cent. iron oxide and about 0.005 percent. carbon. Tungsten metal in the form of powder, such as is used in the manufacture of filaments for incandescent lamps, was the other constituent. This material analyzed 99.8 per cent. tungsten and contained no carbon, The metal powders, in the desired proportions, were mixed by tumbling and formed, under pressure of 20 tons per sq. in., into rods 3/8 by 3/8 by 10 in. To form the alloys without contamination, sections of the pressed rods were placed on alundum slabs and heated in an alundum tube wound with a tungsten resistor and packed in heat-insulating material. While the resistor was heated, a stream of hydrogen was continually passed through both the tube and the case containing it. The tungsten winding on the tube, as well as the material heated within the tube, was thus protected from oxidation. Such a furnace will operate constantly

Jan 2, 1926

By C. -M. Katsari, G. N. Anastassakis

"Copper is considered one of the most important industrial metals because of its properties (conductivity, malleability) and variety of uses. Approximately 70% of the global copper is used for various electrical applications, with a significant part of copper originating from recycling, since copper can be recycled and re-used countless times, without any loss of performance and difference in the quality of recycled copper in comparison to that from ore. Copper recycling significantly contributes to natural resources conservation, waste minimization, energy saving, and overall cost reduction. Approximately, 35% of the globally produced copper originates from recycled copper.The objective of the current work is to investigate the recovery of copper from electric wire scraps using wet shaking table as an alternative to air separation methods that prevail over the wet ones in recycling processes. The tests were carried out using feed of correspondingly high- and low-grade in copper. In the first case, the wire scraps had been subjected to shredding only, prior to tabling separation; in the later, the low-content tailing of prior air separation was used as feed ?n table separation.In regard to testing, the following factors were examined: table tilt, water flow-rate, and reciprocating speed. The results of the tests clearly denote that copper wire separation from plastic polymer is feasible, as in most cases, table separation resulted in heavy products of high purity in copper and high recovery, and tailings of very low copper grade. The results of the current work clearly denote that wet tabling can be applied efficiently for the separation of recycled copper wire from plastic, as an alternative to air separation methods, as well as for the recovery of copper from the low-grade tailings derived from air separation methods."

Jan 1, 2016

By G. D. Bengough

CORROSION tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply f oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case f salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion f the metal was shown in some experiments due to Friend .2 He tested the corrosion f mild steel plates immersed in water in glass jars, a steady stream f air being drawn over the surface of the water in the jars. The air passing through half the number f jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor."

Jan 1, 1929

Deciding on plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g/t of fresh feed has been assumed a reasonable starting point with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2012

By A. M. Gaudin

A GREAT number of hypotheses has been advanced to explain the complex phenomena that are encountered in flotation. In the days of bulk-oil flotation, when a large quantity of oil was employed, it was observed that the oil-mineral aggregate floated above the ore-pulp because of its lesser density. With the advent of froth-flotation this phase of the theory had to be modified to take into-account the presence of air bubbles.. The reason why the mineral-bearing froth of today rises to the top of flotation cells is, of course, because the air-mineral aggregate, with whatever reagent may be associated with it, is lighter than the pulp. In an attempt to explain froth-flotation the fact has been emphasized that certain minerals are wetted and therefore remain in water; while others are not wetted and therefore become associated in preference with air. Such an "explanation" does not explain facts, it merely states them; for instance, it does not explain why minerals are wetted under some circumstances and not wetted under others. Going somewhat further, the wetting or nonwetting of minerals by water has been ascribed' to differences in the angles of contact between oil droplets and mineral surface at the surface of the minerals. This explanation, however, was abandoned when soluble flotation reagents came to replace the so-called "insoluble" reagents. Another theory, sponsored about 10 years ago by Ralston,2 involves the effects of electric charges at the surface of the mineral particles and air bubbles. This theory, unfortunately, was not developed as fully as it seems desirable. The belief that adsorption phenomena might play a preponderant role in flotation3 has been rather widespread for the last 10 years. Unfor-

Jan 1, 1928

By A. M. Gaudin

A great number of hypotheses has been advanced to explain the complex phenomena that are encountered in flotation. In the days of bulk-oil flotation, when a large quantity of oil was employed, it was observed that the oil-mineral aggregate floated above the ore-pulp because of its lesser density. With the advent of froth-flotation this phase of the theory had to be modified to take into account the presence of air bubbles. The reason why the mineral-bearing froth of today rises to the top of flotation cells is, of course, because the air-mineral aggregate, with whatever reagent may be associated with it, is lighter than the pulp. In an attempt to explain froth-flotation the fact has been emphasized that certain minerals are wetted and therefore remain in water; while others are not wetted and therefore become associated in preference with air. Such an "explanation" does not explain facts, it merely states them; for instance, it does not explain why minerals are wetted under some circumstances and not wetted under others. Going somewhat further, the wetting or nonwetting of minerals by water has been ascribed' to differences in the angles of contact between oil droplets and mineral surface at the surface of the minerals. This explanation, however, was abandoned when soluble flotation reagents came to replace the so-called "insoluble" reagents. Another theory, sponsored about 10 years ago by Ralston,² involves the effects of electric charges at the surface of the mineral particles and air bubbles. This theory, unfortunately, was not developed as fully as it seems desirable. The belief that adsorption phenomena might play a preponderant role in flotation3 has been rather widespread for the last 10 years. Unfor-

Jan 1, 1928

By T. H. Troller

FOR a long time propeller-type fans have been considered a very adequate means to move great quantities of air against small static pres-sures. They have been in use for this purpose in mines, as well as in other installations. For static pressures of over 2 or 3 in. of water, the centrifugal blower almost ruled the field until very recently. Some attempts were made to use a number of propellers in line. Such arrange-ments made it possible to obtain pressures higher than 2 in. of water, but they complicated the construction and increased its expense, and the efficiencies were not improved. The more recent development of propeller-type fans has been decidedly influenced by the intensive aerodynamic research in connection with aeronautical development, which has taught us, in particular, how to use airfoils properly. The characteristic that makes an airfoil so valuable is the fact that when it moves through the air a high force component, the "lift," acts on it vertical to the motion, while the "drag" in the direction of the flow is small. The ratio of lift to drag is approximately 20 to 1 at the angles at which the profile is used in practice. An element of the turning blade, the movement of which, relative to the air, is mainly in the direction of the plane of rotation, thus experiences only a small "drag" FIG. 1.-DIAGRAM OF FORCES ON WING SECTION. opposing its rotation, and for this reason a relatively small torque is required at the driving shaft. At the same time there is a strong force component at 90° to the plane of rotation. This force is parallel to the propeller axis in the direction opposite to that of the flow of air, with a correspondingly high pressure increase.

Jan 1, 1936

By John Parker

During 1965, a new stoping method was developed at the Bunker Hill Mine at Kellogg, Idaho to enable the profitable mining of a large low-grade zinc orebody. This method, called the Bunker Hill pillar system, incorporates the use of the air-powered Atlas Copco T2GH or CAVO 310 as the prime production component. The method and equipment proved highly successful and was the first step in mechanizing what had been a classic example of a square-set and horizontal cut-and-fill operation. Since that time there has been a realization that the small rubber-tired type of loader could be effectively used to advantage in increasing productivity and decreasing costs in many different stoping and development applications throughout the mine. The net result since 1967 has been that a large and increasing portion of the mine production and an increasing share of the development is being done with small rubber-tired loaders. Presently, ten Atlas Copco T2GH and six CAVO 310 air-operated loaders are in use, having replaced the time-honored slusher which was first introduced into the Bunker Hill Mine in about 1898 in the form of a slip scraper. The recent advent of diesel powered loaders in the one yard size range has in 1970 further accelerated the trend toward rubber-tired mobile equipment at the Bunker Hill Mine. Although The Bunker Hill Company is using small diesel loaders of several different types and manufactures for inclines, declines and level development and will undoubtedly find stoping applications for this equipment, .the bulk of this paper will be confined to the use of the air-operated loader, leaving the diesel equipment to a future presentation. It is sufficient to say that we feel at this time that the Autoloader type air-powered equipment and the small diesel front end-loader

Jan 1, 1970