Search Documents

By L. C. IlsLey

"According to accident statistics, issued from time to time by the Department of the Interior, Bureau of Mines covering fatalities in coal mines, between the years 1870 and 1921 there were 4,897 deaths caused by explosives. The legislatures and safety commissions of the various mining States have Elected and formulated many excellent regulations in regard to the handling and use of explosives in an endeavor to keep this class of accidents as low as possible. An analysis or comparison of the explosive, regulations issued by over thirty States would make a very long paper, however, by subdividing according to phases and issuing several papers it is believed that the material will be more readily available. The first phase was treated in Serial No. 2405 of the Bureau of Mines (""State and Federal Electrical Shot-Firing Regulations,"" issued in October 1922) which gave a compilation of such regulations as apply strictly to electric shot-firing. The second phase under consideration is ""Who may set off blasts in coal mines.""In some States, the person who does the firing must be an ""authorized shotfirer,"" while in other States he must have proved his ability to do this work, and again in other States he is ""any person."" The present paper covers rules and regulations relating to this phase of shotfiring, and those States having similar regulations have been grouped as follows."

Jun 1, 1923

By Paul K. Edwards

The forces of nature have concentrated sand at various geographical locations that are being mined and processed for a large variety of industrial uses. While most operations serve a number of industries, this paper deals only with the foundry requirements. The forces that have decomposed a source rock, transported this material and redeposited it, have created two general types of sand. These types are classified as the (1) Lake and Bank Sands and (2) Silica Sands. The Lake and Bank sands will contain 92 to 94% Sio2 while silica sands are in excess of 98.5% Si02 and most of the producers wash these sands to up grade their products to 99.5% or better. Included in the Lake and Bank sand would be the river sands that are used primarily for construction purposes. The Foundry Industry is broken down into three types of castings : 1. Grey Iron Foundries The grey iron castings largest market is the automotive industry in Ohio, Northern Kentucky, Indiana, Illinois and Michigan. These castings are poured at temperatures ranging from 2400° to 2700°F. The Silica Sands or the Lake and Bank Sands will satisfy the requirements of the grey iron castings. There are 2 ½ to three million tons per year shipped from the state of Michigan far grey iron castings by the Lake and Bank Sand Producers.

Jan 1, 1974

By Richard Addison

Rosario Dominicana, S. A. operates an 8,500 tonne per dayopen pit gold/silver mine in the Dominican Republic on the Caribbean island of Hispaniola. The mine is located in an agricultural area which is also an earthquake and heavy rainfall zone. In the 64 years from 1910 to 1974 there were 19 earthquakes within 300 km of the mine in the range of 6 to 8 on the Richter scale and the most recent earthquake in this range occurred in March, 1979. Average annual rainfall in the area is 1.7 m and is distributed throughout the year. Safe and environmentally sound tailings disposal in such conditIons has demanded the buiIding of an extremely strong dam wall and use of a fail-safe system of tailings disposal and solution reclaim. The type of dam, the system of tailings disposal and solution reclaim comprise an interesting example of the manner of handling tailings for a medium tonnage mine. The system is relatively costly but does assure a long-term, safe and trouble free structure and operating system. General views of the dam wall and tailings pond are shown in Figures l through 4.

Jan 1, 1980

By S. Lähteenmäki, P. Koivistoinen, J. Levanaho

Semi Autogenous Grinding (SAG) circuit is the most common grinding circuit to day. In Europe and South Africa fully autogenous (AG) circuits are also popular. SAG circuit has a lower capital cost and simple operation. SAG circuit requires the use of grinding balls, which increases operating costs and decreases availability. An AG circuit may produce a higher Net Present Value to the investment. The AG circuit is more complex to design and operate. However, operating experience from AG circuits illustrates that an AG circuit can be as trouble free as a SAG circuit with the benefit of lower operating cost.

Jan 1, 2001

By N J. Welham

This paper reports on an innovative professional development program for school science teachers run collaboratively between the Centre for Sustainable Resource Processing and Murdoch University. Ultimately the initiative aims at increasing the pool of school students with strong science and mathematics backgrounds while highlighting the challenging careers available in the mineral resource sector including the gold industry. The program is unique in that it seeks to develop a network of science teachers who may participate in a series of workshops, short courses and tours over several years. The objective is to raise secondary school studentsÆ awareness of potential careers within the minerals sector by exposing teachers to a real life, hands-on look into the mining and minerals resource industry. Though the program includes the breadth of the resource processing sector, the potential value to gold processing is in developing a greater pool of potential employees. The initiative allows teachers to develop a better insight into the practical applications of the theoretical sciences they are required to teach. The evolution of the program from the first trials with Western Australian teachers to the introduction of the initiative to Queensland teachers are reported on. Additionally, the results of a pilot study involving 40 participating teachers are described. This study used a questionnaire and follow-up interviews to gain quantitative and qualitative feedback from teachers. There is evidence that the professional development program has resulted in teachers acquiring a new found appreciation for the application of the fundamental chemistry and physics they teach within the school curriculum. Also reported are associations between teacher participation in this professional development program and changing attitudes towards the industry in a positive way. Finally, there is some indication that these positive teacher attitudes may result in their students developing a better understanding of the diversity and availability of career paths within this industry.

Jan 1, 2007

By al et, Renzo Yaringaño, Nicolli Duarte, Raul Arquaz

El Proyecto de Au-Ag-Cu de Chanape se ubica en la prolífica franja metalogénica del Mioceno. En Chanape afloran rocas intrusivas (p.ej., cuarzo diorita porfirítica, pórfido de cuarzo-monzodiorita, etc) que cortan las formaciones Millotingo y Pacococha, de edad terciaria. Estas formaciones alojan “pipes” de brecha de turmalina con contenido de Au-Ag-Cu, vetas polimetálicas de Ag-Au-(Zn-Pb-Cu), mantos de reemplazamiento y brechas freáticas y freato-magmáticas mineralizadas. En las brechas de cuarzo-turmalina se ha reconocido un clásico zonamiento vertical incluyendo Cu-Ag-Mo-Au en la base, una porción intermedia de Au-Ag-Cu-Mo y una parte alta de Au-Ag-Cu-Zn-Pb.

May 10, 2023

By Michael Mccorkle

The Turnkey Project contracting approach is a very viable project delivery system for many mine and mill owners. Generally speaking, the Turnkey Project approach makes sense when the owner knows what it wants, is willing to accept the contractors judgement on process elements and maintenance standards, and early construction completion/facility stmt-up are of primmy importance. Projects with unclear process and project objectives make poor candidates for true Turnkey applications. If the objectives are unclear, under development or significant refinement, the owner's effort should go into a good schedule "A" package allowing Engineering, Procurement, and Construction (EPC) contractors to develop cost and schedule proposals for the final design ( engi­neering), procurement and construction of the facility. Figure 1 and 2 graphically depict (in general terms) the stan­dard Design-Bid-Build, Construction Management (CM) Fasttrack, EPC, and Turnkey Approach.

Jan 1, 1998

By Robinson J

A stibnite flotation concentrate from Costerfield in Victoria was found to contain 63.3 g/t An while its sizing distribution indicated that 81.6 per cent of the material was less than 38 ¦m. A 24 hour cyanidation test by a standard bottle roll method recovered 15 per cent of this gold. Pressure cyanidation under conditions of ambient temperature, 40 per cent pulp density, an oxygen pressure of 1000 - 2000 kPa and an initial NaCN concentration of 15 kg/t, resulted in a recovery of 65 pe cent of the gold after only two hours of leaching. Aqueous pressure preoxidation of the concentrate followed by the standard bottle roll cyanidation realised gold recoveries as high as 96 per cent. Conditions of 220¦C, an oxygen pressure of 1000 - 2000 kPa, 16.7

Jan 1, 1991

By Grainger A, Dawkins G, Lysaght A, Kennedy R

Maintenance management improvement projects were undertaken at several BHP Collieries Division mines pursuing.the objective of achieving better structured maintenance procedures. Efficiently structured maintenance and optimum asset use are interdependent and productivity and computer models assist towards that objective. Definition of aspects of maintenance and analysis of the nature of equipment and materials, workloads and tasks, lead to more effective planning and scheduling of maintenance. The quality, standards and procedures of records must be suitable and adequate for storage and future retrieval. Total Quality Control initiatives and improvement projects even extend into spheres of customer/supplier relationships and problem solving teams as well as the more recognisable standards of management and performance factors in maintenance. All such factors contribute to a Maintenance Management Matrix to provide a better structured approach to economic maintenance management in the capital intensive coal mining industry.

Jan 1, 1991

By T. Krumins, L. Zunti, R. Frischmuth

Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals, in high-temperature operations. In a vent application, titanium ignition risk is reduced by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature conditions and therefore titanium ignition risk is dependent on standard operating procedures, and process control interlocks and permissive conditions. It is not uncommon for standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions.

Jan 1, 2014

By Donald F. Saunders

Means and relative standard deviations were calculated for eU, eTh, K, and their ratios for aerial gamma-ray spectral data in 29 quadrangles at 1:250,000 scale. Known or suspected uraniferous provinces were characterized by: 1) Higher eU, eTh, and K means (due to generally higher radioelement concentrations); 2) Higher relative standard deviations for eU, eU/eTh, and eU/K (reflecting the presence of local uranium enrichments); and lower mean eU/eTh and eU/K values (showing uranium loss from "average" rocks to form local enrichments). "Uranium favorability indexes," i.e., combinations of the sensitive variables, show an excellent qualitative relationship to known occurences and geologic favorability. Results appear to confirm the existence of long-term crustal uranium provinces formed at the time of emplacement of the oldest known rocks.

Jan 1, 1980

The richer, shallower sapphire deposits of the New England region of New South Wales which have been traditionally mined by the small miner are almost worked out. Larger mining and exploration companies are replacing the small miner and exploring for the primary source of sapphire or lower grade alluvial deposits.   Although in recent years considerable exploration effort has been directed at locating the primary source, commercial exploitation of sapphire is still restricted to the working of alluvial deposits.   If the Australian industry is to compete against Asian and African producers it must use cost effective exploration, mining) processing and marketing methods.

Jan 1, 1990

Coal is of tremendous importance for the Czechoslovak econ- omy. The current annual primary energy demand being about 109 million tons of standard fuel (1 ton of standard fuel - 7,000 coal = 29,308 GJ), coal satisfies almost two thirds of our fuel consumption. If compared with the distribution of resources in the world's fuel and energy pattern, the situation in Czechos- lovakia is significantly different, as shown in Fig. I. One of the causes behind the difference is that the Czechoslo- vak oil and natural gas reserves and, hence, their production are insignificant, so that it is necessary to import them. Brown coal will continue to play an important role as a prin- cipal domestic source of primary energy even in the future. While the share of nuclear power is increasing, brown coal represents strategic reserves in the fuel and energy balance.

Jan 1, 1989

By Quast K

A series of laboratory flotation tests were conducted to evaluate the effectiveness of various depressants as arsenic (and zinc) depressants in the lead cleaner stage of the NBHC mill at Broken Hill. The depressants used included potassium cyanide, ferrous sulphate, sodium hypochlorite, potassium ferricyanide and two Cyanamid commerical depressants, Aerodepressants 610 and 633. A standard roughing stage was completed before the addition of the reagents in the cleaning stage. All reagents tested produced significant arsenic depression, with the best results being obtained with the addition of potassium cyanide and sodium hypochlorite. Some of the depressants activated the zinc in the process of arsenic depression. The best result was obtained with the addition of 90 g/t potassium cyanide at a pH of 10 when arsenic recovery was only 1/4 that of the value obtained for the standard test.

Jan 1, 1991

The morning session opened at 9:00 a.m. and was presided over by Mr. George A. Nugent, Manager Mining Division, Peter Kiewit Sons' Company, Sheridan, Wyoming. The first speaker was Mr. Jack Huebler, Vice President Research, Institute of Gas Technology, Chicago, Illinois. Mr. Huebler joined IGT in 1961 as Director of IGT's contract research program, a major part of which is IGT's extensive coal gasification work. He is also an adjunct associate professor at Illinois Institute of Technology, teaching gas utilization. Before joining IGT, Mr. Huebler spent 20 years with Surface Combustion Corporation where he was chief research engineer. He developed, designed, and constructed a wide variety of heat processing equipment and the associated chemical processes and was involved in applied research in heat treating, gas chemistry, and gas-solids reactions. He has carried out extensive research on the heat treating of ferrous metals, oil gasification and gas combustion, and has made major contributions to the development, construction, and operation of large-scale industrial furnace equipment. He received B.S. degrees in 10th chemical engineering and mathematics from the University of Michigan in 1941. He has 60 publications including 15 patents. He is also a world traveler in the field of engineering. Mr. Huebler's subject "Gasification of Western Coals." (See Index for printed text of Mr. Huebler's paper.)

Jan 1, 1972

By Thomas M. Drown

ZING is, as is well known, very brittle at a temperature of about 210' C. (410' F.), and may then be readily pulverized in a mortar. By sifting it may be obtained of uniform grain. I have been accustomed to prepare products passing through 40, 60, and 80-mesh sieves, and also by bolting through a fine handkerchief. The principal analytical uses to which I have hitherto applied this material are to the reduction of iron directly from the ore by heating it with the pulverized zinc, and the reduction of ferric to ferrous compounds in solution. In the first case the pulverized ore, 0.5 gram or less, is intimately mixed with about ten times its weight of the pulverized zinc (the finer the zinc the better), in a porcelain crucible, and this mixture is covered with about the same amount of zinc. The crncible is then heated at the top of the flame of a Bunsen bhrner, at a dull red heat, for about ten minutes. The crucible should not be covered. When cool, the crucible, with its contents, is placed in a flask treated with hot dilute sulphuric acid, and brought quickly to a boil. The zinc and reduced iron are dissolved in a few minutes and the flask is then tightly corked and allowed to cool. When cool, the iron is directly titrated by potassium permanganate.

Jan 1, 1879

By A. G. Metcalfe

THE failure to detect any change in the thermal properties of cobalt at the Curie point would appear to indicate that the apparatus may have a limited sensitivity. The Curie temperature has been determined by direct methods to be 1121+3°CP and 1131°C.3 The specific heat has been determined many times'.' and weighted values are given in Table I. The allotropic transformations in iron and titanium, used by the authors to test the experiment method, involved a volume change of the order of 3 pct on going from the close-packed to the body-centered-cubic lattice. These energy changes are likely to be much larger than those involved in a diffusionless transformation from a hexagonal to a cubic-close-packed lattice. However, it has been pointed out that thermal observations are unreliable in the detection of phase changes when these are near a Curie point.' James 0. McCaldin and Pol Duwez (authors' reply)—The sensitivity of the present technique is limited to first-order transformations, so that gradual changes in specific heat, e.g., in the vicinity of Curie points, are not detected. Furthermore, the existence of first-order transformations with latent heats much smaller than those occurring in the known allotropic transformations of iron and titanium is, we agree, still pending.

Jan 1, 1956

By H. O. Hoffman, C. D. Demond

There are two methods of determining the fusibility or refractoriness of fire-clays, the theoretical and the experimental. In the former, conclusions are drawn from the chemical composition; in the latter, from the changes which the clay undergoes when subjeoted to intense heat. It is well to use both methods, beginning with the actual heat-test and explaining the results obtained from this by the help of the chemical analysis. In discussing the subject, however, it is better to reverse this order. I. The Theoretical Method.* Leaving out the hygroscopic and combined waters and any organic matter, as not directly affecting the fire-resisting property, the refractory constituents of fire-clay are alumina and silica, and the fluxing constituents magnesia, lime, soda, potash and ferric oxide. According to Bischof,† alumina is the least fusible component, and silica follows close upon it. If, however, a mixture of the two be heated, it will be found that its melting-point is much lower than that of alumina, as a silicate will then have been formed. The way in which silica affects the refractoriness of alumina has been strikingly presented by Seger 1 in a diagram reproduced in Fig. 1. The abscissæ represent the melting-points of Seger cones Nos. 26 to 36 (see p. 55); the ordinates, the relative amounts of alumina and

Jan 1, 1895

By Henry J. Miller, Marcella Linderman

During some experiments made by Henry J. Miller, partly in Germany and partly in the United States, in which it was found necessary to melt metals in quantities up to 60 kg. in a vacuum or under low pressures of hydrogen, molybdenum was tried as the resistor in the electric melting furnaces. Molybdenum ribbons 16 by 0.55 mm. and 18 by 0.45 mm. were used as resistors. The furnaces were of the type shown in Fig. 1. About the heating tube, Y, are wound parallel resistors of molybdenum ribbon from the water-cooled electrodes, El, Ez. The whole is within a copper container having outlets for the removal or introduction of gases and a window, W, for observation, the space about the heating tube and electrodes being filled with insulating material. The life of the molybdenum used as the resistor was found to depend very much on the manner of using it, its failure being due in some cases to thinning by evaporation or chemical reaction and in others to hardening, which prevented it from following the expansions and shrinking of the heating tubing without cracking. As such failures are often rather expensive in commercial work, it was thought worth while to determine the causes. The factors influencing the behavior of molybdenum resistors used in this manner may be briefly stated as follows:

By H. L. Willett

The self heating of coal, or spontaneous combustion, has been a problem for centuries. This symposium addresses the issue.

May 23, 1905