Search Documents

By Jay P. Tobin

This paper will address the legal standards applicable to construction blasting lawsuits and offer best practices suggestions for pre-blast inspections, documenting the construction blasting work, recordkeeping, and effectively participating and partnering in the defense of a construction blasting lawsuit.

Jan 1, 2015

By Kfw Eick

The paper describes the use of the Nonel millisecond delay blasting system in narrow, deep, tabular ore bodies and briefly describes the standard stoping method as used on Harmony Gold Mine and compares this with the new Nonel short panel system.

Jan 1, 1990

By A. D. Mah

Thermodynamic data on compounds of arsenic and sulfur were critically evaluated by the Bureau of Mines. Changes of standard enthalpy and Gibbs energy, and logarithms of the equilibrium constants were tabulated as a function of temperature for reactions involving these compounds.

Jan 1, 1982

By Howard M. Stainer

Published X-ray mass absorption coefficients were compiled and tabulated. These coefficients are required for various X-ray analytical techniques. Values obtained from 28 authors are listed for 87 elements with both experimental and calculated points included; the wavelengths range from ~0.01 to 68 A. Representative graphs are presented for six elements (lithium, nitrogen, iron, silver, holmium, and uranium. A 37-item supplementary bibliography is also included.

Jan 1, 1963

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

By Robert Rother

El presente texto señala el proceso de exploración y preparación que anteceden la etapa de la producción de mina. Para ello, es necesario ubicar un depósito mineral donde se clasifican en vetas, zonas de cizallamiento, contactos, substituciones y diseminaciones, que se distinguen por la forma de la zona débil en la costra terrestre. Asimismo, es necesario anotar datos como: ubicación, acceso, altura sobre el mar, características de la región, labores, posición del cuerpo mineralizado, sobrecarga, caja y ganga, tectónica y todo lo que se puede ver efectivamente. Posteriormente se evalúa el título de las propiedades, mapeo topográrico y geológico del yacimiento, sistema y costo del muestreo planeado, estudio de las vías de acceso y transportes, reservas de mineral, así como considerar el programa de producción (abastecimiento de agua, mano de obra, escala de operación, tratamiento metalúrgico, valor de la producción, costos de operación, utilidad de operación).

Jan 1, 1964

By K. Osseo-Asare

"The molecular structural and solution chemical characteristics that underlie the surface activity of solvent extraction reagents are highlighted, with particular emphasis on the tendency towards reverse micelle and microemulsion formation. The physicochemical factors that lead to microemulsion-enhanced solvent extraction with chelating extractants are elucidated. Membrane-based contactor systems are described which are uniquely suited for enhanced solvent extraction with microemulsions. The possibility of combining solvent extraction with microemulsion-mediated materials synthesis is discussed. IntroductionThe discovery of new selective extractants has resulted in major breakthroughs which have helped to establish solvent extraction as a versatile separation technology (1-3). A complementary strategy towards new process development is to seek new ways of using the available reagents. This paper explores this second approach. From a molecular structural standpoint, an extractant may be viewed in terms of two components: a polar functional group and a hydrocarbon radical. In the conventional view of solvent extraction, this molecular structure serves two main purposes: The polar functional group provides the binding sites for complexation of metal ions, while the organic group is needed to render the resulting metal-extractant complex organic-soluble. But are these the only properties of the organic and the polar groups that are relevant to the solvent extraction process?In this paper, attention is directed to the fact that solvent extraction reagents possess the molecular structures of amphiphiIes; that is, they are characterized by the presence of spatially separated hydrophilic and hydrophobic groups on the same molecule. A case is made for the view that this amphiphilicity offers interesting opportunities to develop new separation processes which collectively may be described as enhanced solvent extraction (4-6)."

Jan 1, 1996

By Y. M. Zhao

Reutilization of waste printed circuit boards (PCB) can not only prevent potential environmental pollution, but also achieve recycling of secondary resources. Study on recycling of discarded PCB belongs to the front edge of environmental pollution prevention and resource recycling. In order to effectively crushing waste PCB, and solve the problem of secondary pollution of fugitive odor and dust during the crushing process, a wet impacting crusher was adopted to achieve comminution liberation of PCB in water medium. 96.79% of the crushed yield was distributed in ?2mm, and metal took 97.18% in this grade of production. Size distribution of PCB particles was characterized double peaks at the sizes of ?1+0.5mm and ?0.074mm. A double Rosin-Rammler function, is called DRR function, is put forward to describe the size distribution of PCB particles. The DRR function of cumulative weight percentage oversize of PCB was non-liner fitted by self-defining DRR function of the Origin 7.0. The evaluation indexes of the fitting results are the correlation coefficients R2 of 0.9994 and residual E of 0.18671, those show that DRR function is perfectly accurate. Based on the research the mechanical separation and material properties of PCB, a wet process of reclaiming metals from PCB using a new style separator ? tapered diameter separation bed (TDSB) in water medium was designed, and the related separation mechanism was studied. The fluid field of the tapered diameter separation equipment was simulated by the Ansys Flotran software, the variation laws of the velocity in each position in the fluid field as well as the equation of axial distribution sectional max velocity were analysed according to the simulation result, the stress change and motion trajectory of the pellet in the certain fluid field were analysed. The results show that the expanding tubular structure of the varied diameter separation bed indicates gradually decreasing velocity of water flow along the axis, assuming a certain angle in the bed, as a result of the gravity?s influence, and there was corresponding change to the distribution of the flow velocity, thus the whole formed a special fluid field where velocity variations exist in different positions. When the material passed through the fluid field along with the water flow, as a result of the difference to the particle density, the granularity and the shape, there would appear the difference to the motion trajectory as well as the movement distance under the action of the fluid: The lower density materials discharge along with water flow, but the higher density materials would be kept in bottom of the bed and discharge through material mouth. Therefore, light and heavy products were separated effectively according to the density. Using tapered diameter separation bed to process the ?1mm size crushed material of waste printed circuit boards, with the discharge of water 5.5m3/h, feed-rate of the material 250g/min and with an obliquity 35°, product with 93.92% in integration efficiency and 93.73% in recovery ratio of the metal were obtained by the primary separation. Compared with other mechanical methods, the range of particle size was broaden using the TDSB to recovery metals from PCB, and lower limit size of separation almost approach to 0. An innovative process of ?wet impact crushing+ classifying+ tapered diameter separation? recycling metals from waste PCB was developed.

Jan 1, 2014

By G. F. Round

In order to obtain values of angle of shearing resistance and initial resistance for McMurray oil sand for use in general design calculations, the shear strength of this oil sand was measured in a controlled strain type tester, modified so that the rate of deformation could be varied between 0.01725 and 0.1869 inches per minute. Effect of temperature was investigated by adapting the equipment to operate at both 71 ° and 185 °F. The data are reported in terms of angle of shearing resistance and initial resistance for varying rates of deformation, composition and temperature. While the main sets of results reported here were obtained at a bulk density range of 108.7- 109.5 lb. / cu. ft., some results were obtained at a bulk density range of 101-102 lb. / cu. ft. Analysis of varance tables have been drawn up from the results obtained from least squares correlations and significance tests applied. It was concluded that oil content and temperature were significant variables for the degree of shear strength developed by the oil sand; increase of oil content and decrease of temperature each cause an increase in shear strength. The bulk density range 108.7 to 109.5 lb./cu. ft. gave angles of shearing resistance from 30° to 40° and initial resistance values of 0.37 p.s.i. to 0.85 p.s.i. For the bulk density range 101 to 102 lb. / cu. ft., lower values of shear strength were obtained, indicating that compaction density was also of importance

Jan 1, 1960

By A. Azizi, P. Blatter, A. Bouajila

ABSTRACT In-situ monitoring of gold dissolution by means of a rotating electrochemical quartzcrystal microbalance unveiled dramatic decreases in gold leaching from sulphide-rich ore after 360 minutes in an actual cyanidation circuit. Pre-oxidation was effective in enhancing gold extraction by preventing a passive film from forming on gold surfaces. This work aims to highlight efforts undertaken to determine (1) how gold cyanidation is limited by passivation, (2) what reactions and mechanisms are involved during sulphide-rich ore cyanidation, and (3) how peroxidation efficiency of an industrial sulphide ore is controlled by galvanic associations between its sulphide constituents.

Jan 1, 2013

By A. Khoshnevisan

Molybdenum resources around the world are mainly associated with porphyry copper ores. Molybdenite (MoS2) is the main Mo mineral that has rhenium in its crystal lattice. This paper investigates the recovery of rhenium and molybdenum from a molybdenite concentrate using a hydrometallurgical treatment method. The molybdenite concentrate is leached with nitric acid and subjected to solvent extraction to recover and separate rhenium and molybdenum from the leached liquor. The effects of pH and the chemicals? concentration on extraction characteristics of Mo and Re are investigated to define the best condition for selective extraction of these metals. The tested leached liquor contained of 8.2 g/L Mo, 1.5 g/L Fe, 0.5 g/L Cu and 60 ppm Re. A good extraction efficiency, up to 94%, was achieved for Re from the leached liquor, where the extraction of other metals, such as Fe and Cu, was negligible. In particular, at very low pH, rhenium is extracted selectively from solution, while the extraction of molybdenum is less than 10%. After removing rhenium, molybdenum was extracted with LIX984N. The selectivity of molybdenum extraction over other metals in solution was significant. Nearly 94% of molybdenum can be extracted from the solution at a pH value of -0.12, without any interference from other metal ions such as copper and iron.

By P. K. Chatterjee

Computer aided design and inter active graphics have been well established in the electronics, automotive and mechanical engineering industries. The use of such aids in underground mine design and planning, however, has been noticeably absent. The large expense involved in the research and development of CAD and graphics systems and their highly specialized techniques have rendered investment in these areas difficult to justify. Optimum mine planning involves an interactive procedure of evaluation of several alternative plans. Generally the development of each mine plan of a given operation can take many man-months. This time constraint on planning precludes any comparative analysis and evaluation of alternatives, thereby introducing the possibility of unrealized gains. This paper outlines the development of a computer aided mine design program utilizing interactive graphics for the design, simulation and scheduling of underground coal mines. The program developed examines exploratory borehole information and produces a structured database of the sampled data. This database is utilized to generate seam sections and different mine layouts. A simulation of mine extraction and production levels and a schedule of proposed alternatives are then performed.

Jan 1, 1984

By Charles D. Clarke

Para mantener el drenaje de las instalaciones de las bombas en Cerro de Pasco se necesita un aproximado de 3700 galones por minuto. Empero del total de los 3700 galones por minuto, 2500 es agua ácida y el restante; 1200, es agua dulce. Por tal motivo, el objetivo del siguiente trabajo es revisar los problemas de mantenimiento de las bombas -en tanto represente la consecuencia del agua ácida de las minas-,para reducir los costos y las causas de deterioro, asimismo reparar en las corrientes extraviadas como causas corrosivas serias, que necesitan ser adecuadamente protegidas desde el momento de su instalación y supervisadas periódicamente, Por último, aislar adecuadamente las bombas de las corrientes extraviadas, reduciendo la posiblidad de la acción galvánica de los equipos eléctricos instalados a proximidad.

Jul 20, 1955

By R. W. Huber

While conducting an investigation on electrolytic reduction of magnesium oxide in 1943, it became necessary to obtain accurate data on the conductivity and density of various mixtures of fused chlorides. AZ the required information was not available in the technical literature, or there were inconsistencies in the data from several investigators, an independent study was made at the Bureau of. Mines laboratory at Salt Lake City on the conductivity and density of the molten chlorides MgCl2, CaCl2, BaCl2, KCl, and NaCl and the binary mixtures of MgCl2 with the other four chlorides. Studies were also made on the binary system KCl-CaCl2 and on certain portions of several ternary systems. Measurements covered a temperature range from the melting point to 1,000° C. The results of this study were reported in an intra-Bureau report prepared early in 1944. Since then the Bureau of Mines has received several requests for data on fused chlorides; the results of the previous study, therefore, are being published to make the data available.

Jan 1, 1952

By Paul M. Tyler

THE farmer pays the phosphate miner! Phosphorus is used in fireworks; goes to battle in military smoke screens, incendiary shells, and tracer bullets; and, in vermin destroying pastes, does its part in the war against insects. A lemon phosphate can be had for a nickel at most soda fountains, and tens of thousands of tons of phosphate rock are mined annually for use in the food industries, chiefly for making monocaleium phosphate baking powder. Sodium phosphate cleaning, washing, and scouring compounds consume substantial quantities: the iron and steel industries buy a few thousand tons yearly to make ferrophosphorus and to balance foundry-iron furnace charges; and even nonferrous metallurgists use a little for phosphor bronze and other alloys. Phosphoric acid, its salts, and diverse other derivatives of this versatile element have countless applications, and industrial outlets are increasing rapidly, especially in the United States. Nevertheless, in this country nearly 90 per cent and in the whole world fully 95 per cent of the phosphate rock consumed is absorbed ultimately in agriculture.

Jan 1, 1938

By Antonio Adel dos Santos

Visando elucidar o comportamento da carepa terciária durante a laminação de tiras a quente, em um aço produzido como laminado a quente e com rigorosa exigência de qualidade superficial, foi realizada uma parada forçada do laminador, impondo-se, imediatamente, um resfriamento rápido da superfície da tira. Amostras coletadas na região do arco de contato mostraram que a carepa possui espessura na faixa de 10 ?m a 14 ?m na entrada das cadeiras, sendo reduzida para 7 ?m com a deformação, sem ocorrência de ruptura. Tais características indicam que, do ponto de vista do comportamento no trem acabador, a carepa apresenta espessura e plasticidade adequadas para evitar defeitos nos produtos laminados. A carepa foi constituída predominantemente por Fe3O4, óxido plástico na temperatura de laminação. Foi desenvolvido e aplicado um modelo de crescimento da carepa, que forneceu valores de espessura muito próximos dos medidos, se tornando uma ferramenta útil para análise da influência de condições de processo na carepa.

Oct 30, 2017

By T Suwa, S Ishida, J Xue, S Fuchida, H Shimada, Y Aoki, C Tokoro

Pyrite depression with prolonged pre-conditioning treatment in high salinity water has attracted much of researchers’ interest in recent years considering the increased utilisation of multiple stage flotation, closed water circuits, clay minerals, and sea water in flotation plants. In this study, the role of calcium (Ca)/magnesium (Mg) precipitates in stabilising the dissociative ferric hydroxy-xanthate (FHX), and its effect on modifying the balance of hydrophobic/hydrophilic species on the pyrite surface were primarily investigated. The total amount of extractable Fe-bearing species on pyrite concentrates and tailings after floatability test was quantitively determined using ethylenediaminetetraacetic acid (EDTA) extraction tests combined with inductively coupled plasma optical emission spectroscopy (ICP-OES). A more evident accumulation of extracted-Fe in pyrite concentrates rather than it in pyrite tailings was observed at both pH 9 and 10.5 when pyrite was pre-conditioned in Ca/Mg-bearing solutions for 360 min. Fourier transform infrared (FTIR) spectroscopy showed the main xanthate derivatives changed from di-xanthogen (1155 cm-1 ) to FHX (1167 cm-1 ) on the oxidised pyrite samples that were preconditioned in Ca/Mg-bearing solutions. Scanning electron microscopy-energy dispersive spectrometry (SEM-EDS) suggested the preferential accumulation of FHX upon secondary Ca/Mg-bearing precipitates as reflected by the higher Fe/S ratio together with the decrease of O element herein after xanthate conditioning. Although the hydrophilic secondary Ca/Mg/Fe-bearing minerals on the pyrite surface generally deteriorate pyrite’s floatability, the upper section of these secondary hydrophilic aggregates is partially covered by FHX alongside with further multilayer-adsorbed di-xanthogen. The precipitated Ca/Mg-bearing precipitates promotes the immobilisation of dissociated FHX derived from the reaction among iron oxyhydroxides and xanthate anions upon the localised secondary Ca/Mg/Fe-bearing minerals via acid–base complexation. Therefore, this phenomenon alleviates the hydrophilic modification of secondary Ca/Mg/Fe-bearing minerals to pyrite considering the immobilised FHX upon localised precipitates shows a slight hydrophobicity, and meanwhile, the upper FHX benefits the multilayer adsorption of di-xanthogen via the interaction among their inner hydrophobic alkyl chains.

Aug 24, 2022

By W. H. Tomlinson

The fourteenth National First-Aid and Mine Rescue Contest we;; held at the State fairgrounds, Columbus, Ohio, October 2, 3, and 4, 1951. The meet, the first such event in 21 years, was under the auspices of the Bureau of Mines, United States Department of the Interior, and the Joseph A Holmes Safety Association and was sponsored by the National Coal Association, the United Mine Workers of America, and various State mine-inspection departments. The cooperating agencies that contributed to make the meet a success, in addition to the National Coal Association and the United Mine Workers of America, were the Kentucky Department of Mines and Minerals, Ohio Division of Mines, West Virginia Department of Mines, Pennsylvania Department of Mines, and the Columbus Convention Bureau. SUMMARY Fourteen teams from 6 States participated in the mine rescue contest, and 55 teams from 9 States competed in the first-aid contest. Only one of these teams entered as a combination team, that is, participating in both the mine rescue and first-aid contests. The States represented and the number of teams from each State are listed in table 1.

Jan 1, 1953

By John R. Bartels

This Bureau of Mines report describes the development of a preliminary design for a novel, protected, cab-shuttle car for use in working seam heights down to 40 in. Because of the severe restrictions imposed by low-coal operation, Mine Safety and Health Administration (MSHA) regulations only require canopy protection on shuttle cars operating in seam heights of 42 in or greater. MSHA routinely grants variances for canopy use in seams 48 in high or less. The design was generated by giving the operator needs equal priority as related to machine performance parameters. Cab-shuttle car concepts that led to the recommended design are described, along with criteria and testing used to evaluate their potential effectiveness.

Jan 1, 1988

By Joe M. Short

More than eighty years ago, in what we generally consider a more leisurely age, workers and engineers began the construction of the longest railroad tunnel in the world. When completed, the Simplon Tunnel ran more than twelve miles through the alps to connect Switzerland and Italy. Work began in 1898 and the tunnel was completed in 1905. In all it took about seven years to build one of the world's great tunnels. More than seven years ago, in what was hoped to be a rapid and constructive to the deaths of 38 workers in two spectacular tunnel disasters in 1971, the secretary of Labor's Construction Advisory Committee on Safety and Health began in January 1972 a search for an effective standard on tunnel safety. Much hard and useful work has been done, especially by the construction advisory committee' but more than seven years later, we still don't have a tunnel standard. We may speculate that, when the Simplon Tunnel was completed, workers and their bosses assembled to celebrate their achievement and to count their casualities. We have no need to speculate on the lack of achievement up to this time. An so far as I know, the bureaucrats have suffered no casualities except perhaps some unreported cases of ring-around-the-color. The only moral I can draw from all this is thai it is easier to penetrate solid rock than it is to get through bureaucratic fog. We can only hope that OSHA will finally take advantage of the work which was finished years ago and complete the actions necessary to give us a tunnel standard. Having made my point, I could stop my remarks right now; but

Jan 1, 1979