Search Documents

By Marcel Schlumberger

The electrical methods for surface-prospecting have been well developed in the last 20 years. The method involves, in the classic form, the sending of an electrical current into the soil, by means of two electrodes A and B, and studying the potential distribution at the surface, by measuring the difference of potential between pairs of points such as M and N. The points M and N are usually placed on a line between, and equidistant from, A and B. By increasing the distance AB, the current sent into the Earth, and likewise the distribution of surface-potentials, become influenced by regions of greater and greater depth below the surface. By varying the form and dimensions of the electrode-arrangements AMNB, called a "quadripole," one may make valuable deductions concerning the nature or thickness of beds, if one knows the electrical properties of these beds. On the other hand, if the form and dimensions of the electrodes AMNB remain fixed, the depth of penetration of currents in the Earth remains, so to speak, almost constant, although it tends to increase where the subsoil is more conductive, and conversely. Therefore, if one moves the constant-dimension quadripole over all the terrain to be Investigated, one achieves approximately a horizontal exploration. This permits a study of tilted beds or faulted horizon-tal beds. When the particular problem becomes deep, of the order of 2000 meters, or more, it is ne-cessary to Increase the distance between the current-sources AB to a length such that the work 'comes very troublesome, especially if the region is wooded. At the same time, the separation the points M and N must be likewise great (for example, one km) in order to obtain differences potential which are not too small; the measurement of potential differences across MN is then difficult because of the presence of parasitic potentials, due to a flow of telluric currents in fourth, and the order of greatness of these currents may exceed the quantities to be measured.

Jan 1, 1940

By Nils Heinke, Stephen M. Collinsorth

To anyone who is responsible for the production of blast holes, who is looked to on a daily basis for drill maintenance and performance, whose bottom line may depend on the survival of the mine itself.. How much awareness should one have on such things that truly impact production, maintenance and overall job cost? Do you know your drill’s maximum capacity?

Jan 1, 1998

By McKenzie P

The techniques of geological control developed by the Coal Geology Sections of the Broken Hill Proprietary Company Limited and Australian Iron and Steel Proprietary Limited in providing geological service in the coilieries operated by these associated companies cover the provision of geological control for both planning and production in each of which the significance of geology has in the past been only poorly appreciated by the coal mining industry.While the adoption of similar techniques is well within the capacity of major companies there is considerable scope for the development of government geological services providing specialized assistance of this nature for smaller scale producers.INTRODUCTIONThe coal mining industry in Australia can instance many notable mistakes caused by failure to obtain sufficient geological information or by incorrect interpretation of available geological evidence both before the commencement of mining and during the progress of operations. Substantial development undertaken in, areas with insufficient or inferior coal reserves, difficult mining conditions caused by failure to adjust operations to geological circumstances, and the irregular development of mine workings caused by unexpected geological features, all bear witness to the lack of geological foresight by the industry.Along with the more widespread general use of applied geology, an increasing acceptance has developed during the past ten years of the valuable contribution which can be made by this science to the exploitation of coalfields. In spite of the advances which have been made, there is still a wide scope for further detailed application of geology throughout the coal mining industry in Australia.

Jan 1, 1963

By Johnson G. D

The typical management systems used to address the issue of operating risk centre around technologies that identify, analyse and evaluate the risk factors. These logical systems such as HAZOPs, Fault Tree Analyses, etc rely heavily on technical considerations and process flow analysis. However, several research projects, across industries and countries have clearly shown that up to 80 per cent `operating risk' is determined by the actions of workers, supervisors and managers. Yet, most of the focus of risk management is on technical and procedural issues. This suggests that a significant imbalance exists in our management systems and that industries are unlikely to show significant improvement on current levels of safety performance. Effective risk management must include the intangible element of the organisation psychology towards risk. A practical and theoretically sound approach had been researched and developed in and for the mining industry. This paper describes the approach and methodologies applied at the Cosmo Howley Gold Mine in the Northern Territory, where an inclusive approach to managing financial and operating risk was followed. The Cosmo Howley Mine showed a dramatic reduction in lost time injuries and improvements in financial indices - providing conclusive evidence of the link between management effectiveness, safety and productivity. This `triangle' has often been the subject of speculation and theory. It is demonstrated in this paper how the management team of Cosmo Howley focused their practices and systems on the improvement of organisational dynamics, ensured tangible and clear focus on parameters of costs and safety and how the improvement process was managed. It is concluded that the improvement process did not require a `major re-engineering' of the organisation. The organisation culture changes that occurred were incremental, planned and effective. It entailed the implementation of sound risk management methodologies, and ensured that a significant emphasis was placed on an aspect that is defined as `organisational dynamics'.

Jan 1, 1994

By J Vann, S Dunham, M Job

Two-dimensional (2D) estimation approaches have significant advantages over three-dimensional (3D) approaches when dealing with a narrow vein- or layer-like geometry. The main motivation for 2D estimation is that bias due to non-additivity of grade is avoided. The various aspects of 2D estimation are illustrated by use of a case study from the 1A Shoot Nickel deposit at Leinster, Western Australia. The width of the 1A mineralisation is variable, and so are the angles of drilling intersection. Consequently, the variable of interest (in this case nickel grade) is not suitable for direct kriging because it is defined on non-uniform support. However, grade can also be defined as the ratio of two variables that are suitable for direct kriging: thickness and accumulation. In the 2D approach, tonnage equates to thickness and metal equates to the product of grade and thickness, also called æaccumulationÆ. In the simplest approach we can independently krige accumulation and thickness and derive the grade by the ratio of the two resultant estimates. The thickness and accumulation variables must be in a consistent projection orientation, for example a horizontal projection in the case of steeply inclined mineralisation like 1A. Because the density is not constant across the 1A (and most other) deposits, the issue of density weighting is also discussed. The impact of the correlation between grade and length, or grade and density are important issues in implementation of 2D estimation. The circumstances under which these correlations need to be taken into account (by co-kriging) are reviewed. Finally some comments are made on the final use of the resultant 2D estimate for mine planning purposes.

Jan 1, 2003

By E. V. Daveler

THE milling plant of the Alaska-Gastineau Mining Co. is located at the town of Thane, Alaska, on Gastineau Channel, 4 mi. south of Juneau and directly across the channel from the Ready Bullion mine of the Treadwell mines on Douglas Island. Previous to the organization of the Alaska-Gastineau Mining Co., in 1912, the milling was done at the stamp mill of the Alaska Perseverance Co. located at the mine in Silver Bow Basin. But the contemplated increase in production made it necessary to locate the mill on Gastineau Channel, as not enough water was available at the mine during the winter months, nor was there room for taking care of the large tonnage of tailings that would ultimately be discarded from the mill. CHARACTER OF ORE The gold and silver values occur in quartz lenses associated with pyrrhotite, galena, arsenical pyrites, and zinc blende. These lenses occur in large bodies of slate, schist, and metagabbro, which also carry some valuable metallic contents. With the essential low cost of mining, it was necessary to mine large bodies of low-grade material containing the high-grade streaks. Of the minerals, pyrrhotite, the magnetic sulfide of iron, is predominant, and galena is the next sulfide present in quantity. The gold occurs free and coarse and associated with the iron sulfide in its finer state. The silver occurs with the lead or is alloyed with the gold. A chemical analysis of the ore shows Silver 0.10 oz. Magnesia 0.4 per cent. Silica 59.7 per cent. Sulfur 1.2 per cent. Iron 5.2 per cent. Lead 0.1 per cent. Alumina 21.4 per cent. Zinc 0.2 per cent. Lime 5.0 per cent.

Jan 1, 1920

By Henry F. Cooper, Scott E. Blouin

Large jacking test procedures that have been applied to obtain static in-situ rock properties (Ref. 1) have shown that the in-situ rock modulus and strength can be considerably less than what would be obtained from laboratory tests on intact samples. This trend is also expected to be true for dynamic properties, but few dynamic in- situ rock property tests have been conducted. During the past several years, high explosive test procedures have been developed to simulate the airblast and direct induced ground motions (Ref. 2) produced by nuclear explosions . These test procedures load large volumes (up to 10 7 f t3) of the earth with stress levels sufficiently high to produc5 feet of particle displacement over surface areas up to l0 5 ft2. This paper discusses some of the data obtained, and the implications of these results for our understanding of the dynamic response of in-situ rock. DESCRIPTION OF TEST PROCEDURES As shown in Fig. 1, the High Explosive Simulation Technique (HEST) consists of a cavity of uniform height bounded on the sides by a soil berm, above by an overburden of uniform thickness, and below by the test bed on the earth's surface. Horizontal racks of detonating cord are placed in the cavity and detonated at one end of the test bed. This detonation produces an explosive wave that propagates across the test bed, loading the earth with an overpressure pulse that decays with time because of the compression and lifting of the overburden. Since 1964, there have been approximately 40 such tests on test bed areas ranging from a few hundred to l0 5 sq ft., simulating peak overpressure conditions between about 100 and 6000 psi and specific impulses between a few and over 100 psi-sec.

Jan 1, 1971

By C. K. Leith

MANGANESE is one of the minerals which is principally consumed in countries other than those of origin. Nearly 85 per cent of the pro-duction is used by the United States, England, Germany and France, and roughly a third of the total is used by the United States alone. On the other hand, over 85 per cent of the world production comes from Brazil, Russia, India, the Gold Coast of Africa, and the Sinai Peninsula. It follows from this fact that practically all manganese moves across international boundaries in raw or alloy form, and much the larger part of this movement is for considerable distances and is ocean borne. There is no indication that any one of the principal consuming countries can develop even approximately adequate supplies of its own. Under abnormal war conditions, with high prices and changes in metal-lurgical methods, only 35 per cent of the needs of the United States was met from local sources, and under our recent tariff only 11 per cent. There are thousands of manganese deposits scattered about the world, but only a very few which can figure largely in supplying requirements on a modern scale. The known reserves, together with highly probable extensions and explora-tions now under way, indicate no shortage from a world standpoint for many decades to come. The production and marketing of manganese is going steadily into fewer and stronger hands. The steel in-dustry uses over 90 per cent of all the manganese mined, and is acquiring control of a considerable part of the production in all of the principal fields-the Germans in Nikopol, the English in India and Gold Coast, the Americans in Georgia, India, Gold Coast and Brazil. Some of the controlling companies are of international scope. Concentration of commercial control is a notable tendency. A natural consequence is the growing un-easiness of smaller consumers the world over about their ultimate supplies and desire to know more definitely how and where manganese supplies will be controlled in the future. The sources of supply are few enough to warrant the belief that more or less monopolistic ele-ments of control are not impossible.

Jan 5, 1927

By Percy Hopkins

KIRKLAND LAKE, the second most important gold area in Ontario, is situated in the north¬eastern part of the Province, 392 miles north of Toronto by railway. It is reached by a five-mile macadam road from Swastika, a village on the Temiska-ming & Northern Ontario Railway, 63 miles north of Cobalt. Gold, was first found at Kirkland Lake in 1911 by W. H. Wright. on claim No. 1830, now a part of the Wright-Hargreaves mine. In January, 1912, the metal associated with various tellurides was found by Harry Oakes and George Tough on the Tough-Oakes property 3/4 mile east of the lake. The shipping of hand-sorted, extremely high-grade ore, valued at $350 to $450 in gold per ton, from this property created great interest and resulted in numerous other discoveries. The early developments of the area, however, were much retarded on account of war conditions, labor troubles, and owing to the ore zone being largely under the bed of Kirkland Lake or in drift-covered depressions. It was not until early in 1918, when the Lake Shore Co. found its rich orebody under the bottom of Kirkland Lake, that the various ore deposits were believed to be more or less continuous along one main vein system. From that time most of the work in the area has been done along the "main vein" with gratifying results. Production began late in 1912, and up to the end of March, 1923, the five producing mines have yielded gold, with some silver, valued at $8,379,403. The production in 1922 was $2,162,548; that of 1923 should be over $3,000,000. The same general assemblage of rocks which occurs at. Kirkland Lake extends easterly for many miles to Larder Lake and beyond; hence there is a large area containing formations favorable for gold prospecting. In this general area numerous prospects are being operated, and among the most promising ones, may be mentioned the Argonaut, Crown Reserve and Asso-ciated Goldfields near Larder Lake. A 25-mile branch railway is now being constructed across the mineral area from Swastika to Larder Lake, passing through Kirkland Lake.

Jan 8, 1923

A low grade, refractory ore gold mine with high striping ratio such as at Macraes is always challenged in ways to improve margins. Common practice approaches used at OceanaGold Ltd Macraes are to maximise grade delivery, optimise recovery and reduce unit costs, as well as take any opportunities to incorporate new technologies and implement enhanced commercial strategies.   The Business Improvement (BI) programme was implemented across the Macraes operations in late 2003 and is being rolled-out to all other parts of the business. The core focus of BI at OGL is to: +        increase revenue, +        reduce cost, and +        improve processes.   A dedicated BI team comprising of a manager, team leaders and business analysts were engaged to identify and manage a series of opportunities to reduce operating expenses, optimise capital outlays and generate extra revenue. The Business Improvement Programme, though in its formative phase, has begun a cultural change within the organisation. Many people are starting to challenge the way they do things and are looking for ways to continually improve business performance.   The BI team encompasses individuals from different departments who can offer the diverse skill set necessary to produce intended results. The current team is made up of a BI manager, BI Team Leaders in Mining and Processing and analysts from Mining, Processing, Commercial and Plant Maintenance workgroups. A team member has recently been formally trained as a Six Sigma Black Belt. ] The BIÆs team role is to assist in the establishment of project management processes for each improvement idea. In addition the team will assist in tracking implementation, identifying and unblocking restrictions and limitations as well as setting up metrics to quantify the level of benefit returned and sustained.   From a more strategic point of view, the BI team is advancing the Business Improvement capability of the company by developing long term Communication and Training strategies. These strategies will set the direction of BI initiatives in the years to come to: +        educate the OGL workforce in basic BI techniques, +        assist the OGL workforce in applying basic BI techniques, +        communication the direction of BI in OGL, and +        close the information feedback loop to facilitate transparent communication between the OGL workforce and the BI team.

Jan 1, 2004

IF you wish to make the acid that is vulgarly called common aqua fortis,* for parting gold from silver, you must first provide as many cucurbits and alembics, receivers, and materials as you wish, and then make a furnace that is long and conveniently wide for holding three or four pairs of cucurbits or as many as you wish. If you have to make this by art in order to work a large quantity, you could make several small furnaces for it seems that not more than three or four pairs are suitable for one. Prepare the places where the cucurbits are to stand with bottoms or covers made of potter's clay or tiles that are half round like the bottoms of the cucurbits and have a little rim around the top so that they can be built in. Proceed to build these in in pairs, one by the other with convenient spaces between, placing an iron support across to make this place stronger and more secure. In every corner and also in the middle a hole must be made as a vent for the smoke, as is done in all furnaces. You will see the form of this somewhat roughly drawn here. [Figure 25] Near this prepare a number of cucurbits which are made of glass, as clear and uniform as possible and very well formed. There must be no bubbles or other indentations in these, for they would be dangerous and uncertain for your work. Lute these with lutum sapientiae up to within three dita or less from where the neck narrows. This lute must be spread out well all over to the thickness of two threads or a little more. Then cover and make them strong with this well-made plaster, and finally dry it, taking care that there are no clefts or cracks such as clays are often prone to make even though they be well prepared. For greater security choose among these [64v] a clay that is lean and then mix it with at least a fourth part or more of wool-clloth clippings and about an eighth part of wash

Jan 1, 1942

By J. Campbell

Long freezing range casting alloys are particularly susceptible to a type of porosity which is observed to form in layers parallel to the supposed position of the isotherms in the solidifying casting. Under favorable conditions (which appear to be typified by low-temperature gradients in the casting giving rise to a wide and more or less uniform pasty zone, and which arise from several factors, particularly: a) wide freezing range alloy, b) high thermal conductivity of metal, c) low thermal conductivity of mold, and d) high mold temperature3) layer porosity has been observed in many different casting alloys: copper,' aluminum, magnesium,' steels, and high-temperature alloys.3 Baker4,5 and later cibula6 argue that layer porosity occurs because of thermal contraction, in a manner analogous to hot tearing. In outline, the theory consists of the establishment of a coherent dendrite network by the impinging of dendrite tips. Subsequent shrinkage imposes tensile stresses on the network which tears perpendicularly to the stress, i.e., parallel to the isotherms. If these tears are not filled by the inflow of residual liquid then layers of porosity result. Baker7 attempted to test whether the porosity was the result of thermal contraction by casting test pieces in a mold designed to accentuate hot tearing. However, no significant increase in porosity was observed. This negative result of Baker's critical experiment appears to be substantiated by numerous observations, particularly the experiments by Lagowski and Meier8 on Mg-Zn alloys covering the range of zinc contents up to 30 pct Zn. These clearly reveal that the maxima for the incidence of hot tearing and layer porosity are well-separated, occurring at 1 and 6 pct Zn, respectively. Furthermore, the thermal contraction maximum occurred at 1 pct Zn, indicating that hot tearing is associated with contraction in the solid state, and not with porosity. These observations are further substantiated by the elementary consideration that the thermal contraction of the casting is likely to produce (if anything, since the temperature difference across casting of high thermal conductivity, such as aluminum and copper, is likely to be negligible) a compressive stress on the

Jan 1, 1969

By J. F. Wolff

The iron formation of the Gogebic Range in northeastern Wisconsin and the northwestern part of the Upper Peninsula of Michigan, resembles that of the Mesabi Range in Minnesota very closely in lithologic character and the subdivisions and horizons that can be recognized. It contains numerous interbedded slaty layers and considerable intraformational conglomerate in certain horizons. In contrast to the flat dip of the Mesabi formation, the Gogebic dips steeply to the northwest at an average angle of about 70". It has a quartzite and siliceous slate foot wall and a hanging wall of conglomerate, graywacke and slate. The black and gray Tyler slate has been designated the hanging wall of the Gogebic iron formation in U. S. Geologicial Survey monographs, but between the true Tyler slate and the commercially important Gogebic iron formation, and apparently unconformably upon the latter, is a series 600 ft. or more thick of conglomerate, slate, graywacke, and cherty iron formation, the latter being of no commercial importance on the Gogebic Range as far as now known. This series is probably that described as the "Capps" on the eastern Gogebic by the Michigan Geological Survey. The Gogebic iron formation proper can be subdivided into three main horizons, a lower cherty and an upper cherty with a banded or slaty horizon between them, corresponding to the three lower horizons of the Mesabi. Several minor subdivisions can be made of these major ones. Orebodies occur in all three horizons of the Gogebic series and in some places ore is developed across practically the entire series. Dikes and Sills The Gogebic iron formation has been intruded most intricately by basic dikes and sills, most of the former pitching east but some pitching west. One very extensive sill is intruded near the base of the lower slaty or banded horizon, in the formation known locally as the Yale slates. One extensive bedding or strike fault is associated with this sill and a great many transverse faults occur at different places along the Range. The combination, or association, of steep dip, faults, dikes and sills has produced conditions very favorable for the development of orebodies through the leaching, oxidation, and consequent concentration effected

Jan 1, 1925

By R. A. Vandermeer

It is usually assumed that the rate-determining step in the migration of a grain boundary involves the thermally activated transfer of single atoms across the interface. Chemical reaction rate theory then gives a migration rate which is proportional to the driving force when this is small compared to kT.1 In their recrystallization studies on aluminum, Gordon and vandermeer2 obtained data which was capable of providing the first experimental test of this proportionality. They correlated stored energy (driving force) release measurements determined calorimetrically with fraction recrystal-lized kinetic (growth rate) data acquired metallo-graphically at a temperature where a significant amount of recovery takes place concurrently with recrystallization. Within experimental error, the results of Gordon and Vandermeer confirmed experimentally, at least over a limited range, the linear dependence of boundary migration (growth) rate on driving force in accordance with theory. In obtaining these results, however, an incorrect, implicit assumption was made in relating the average instantaneous growth rate of the recrystallized grains to the measured fraction recrystallized kinetic data. The purpose of this present note is to point out and correct this assumption. An alternate approach, whereby a more proper average growth rate can be calculated from the recrystallization kinetic data, is presented. The earlier data, reevaluated in terms of this new approach, show the same general trend as before so that the original conclusion of Gordon and vandermeer2 is still valid. As was shown in a detailed study3 of the geometrical features of recrystallization in aluminum, the colonies of recrystallized grains can be regarded as uniform cylinders embedded in a three-dimensional matrix, the number of such colonies being constant. Thus during the early stages of recrystallization the volume fraction recrystallized, Xv, can be written as Xv=ynvlr2 [l] where y is a shape factor and i and r are defined as the average length and radius of a recrystallized colony and are spatial averages over the specimen. -nv, is the number of such colonies in a unit of volume. The erroneous assumption made in the earlier paper2 was that r in Eq. [I] could be replaced by

Jan 1, 1965

By M Stewart, J Vann, S Dunham

Geometallurgy is an emerging, cross-disciplinary field that integrates spatial models of rock properties with time-based outcomes of mining and treatment processes. Geometallurgical variables include any rock property that has a positive or negative effect on the business. Some of the more critical geometallurgical variables include recovery, grindability, throughput, power consumption, mineralogy and content of deleterious materials. These variables drive project costs and revenues in a fundamental way and thus geometallurgy has potential to positively impact on the value of strategic and tactical decisions across many mining organisations. Geometallurgical models, like traditional grade-only models are based on samples collected from the mineralised and non-mineralised regions of the deposit. The nature of some non-grade variables, particularly those that are dependent on the ore treatment processes, requires special consideration during sampling and subsequent spatial modelling. Failing to objectively consider the characteristics of variables may seriously compromise the validity of the sample selection, sample treatment, data models and the subsequent decisions. In addition to addressing the vexed question of collecting an æunbiased and representativeÆ sample, the sampling and modelling approach must consider issues of scale, both geostatistical support and also the relationship between bench-scale data and operational-scale mineral processing performance. This paper proposes a framework (the Primary-Response framework) for the classification of geometallurgical variables. This framework is designed to assist with developing sampling approaches and identifying the most appropriate spatial modelling approach. The proposed framework can also help identify the risks associated with designing, sampling and modelling of both types of geometallurgical variables. The Primary-Response framework divides variables into two categories; primary variables and response variables. How a variable is classified in this framework depends on the degree to which the variable reflects either an intrinsic attribute of the rock (æprimaryÆ) or its response to measurement processes (æresponseÆ). Depending on the classification in this framework, appropriate sampling and modelling decisions can be made to minimise the risk associated with the incorrect treatment of the variable. In particular, the authors argue that for response variables, the approach taken to building spatial models may need to be different to conventional linear averaging approaches (for example kriging).

Jan 1, 2009

By George Smith

The Australian Broken Hill Consols mine is situated within a third of a mile eastwards of the famous Broken Rill Proprietory mine; but, so far as has yet been proved, the respective lodes have no connection whatever. The Proprietory line of lode, striking N.E. and S.W., is coincident with the bedding-planes of the inclosing gneiss, and, according to Mr. E. F. Pittman, A.R.S.M., government geologist, is undonbtedly a saddle-formation. This opinion, which met with much opposition at the time it was advanced, is now, I understand, being generally confirmed as the work of development opens out fresh areas for observation along the line of lode. The lode is of immense thickness—in places over 300 feet and though it has been found to contain sufficient quantities of secondary silver compounds to yield phenomenal outputs of silver, its principal constituents are various lead and other ores, and it would appear more correct to regard it as an argentiferous lead-deposit than as a silver-lode proper. The Consols lode differs from its gigantic neighbor in every respect. With an average thickness of not more than 18 inches, it has been worked along its course for upwards of 1300 feet, and at every point yet explored has been found remarkably well-defined and persistent. With a strike E. and W., it cuts obliquely across the bedding of gneiss and schist, continuing uninterruptedly through various bands of eruptive amphibolite. The dip, which is to the south, ranges from 24 near the surface to nearly vertical in the lower levels; but the alteration is not regular, as in places the lode is almost flat, and this at a vertical depth of over 300 feet. These changes of inclination have had no effect on the ore-deposits, which, as I shall endeavor to show, have been governed entirely by " cross-

Jan 1, 1897

By C. P. Melloy

INTRODUCTION Ventilation practice at Isa Mine has been evolving since underground mining began in 1931. Much fundamental work has been conducted and reported regarding the primary ventilation system [Mathews K.E. et a1 (1967) and Brown J.R., Fisher T.H., Gibson K.L. (1979) 1. However, ventilation networks for subsystems such as open stopes, have evolved with experience. This paper outlines current ventilation practice for open stoping. Mount Isa Mine The mine is located in semi-arid North-West Queensland, Australia, and currently produces 20 000 tonnes of copper ore and 10 000 tonnes of silver-lead-zinc ore daily in each five day working week. Mining extends over a north-south strike length of 3.5 km with a maximum width across dip approaching 1 km, and is to a depth of 960 m (Figure 1). At present approximately 90% of the mine's copper production is from the 1100 Orebody, which contains ore reserves of 121 million tonnes of 3.2% copper. Open stoping is currently the mining method employed, and is used for primary stoping and pillar recovery adjacent to cement fill walls. The development of stoping methods in the 1100 Orebody has been documented by Kirkby R.W., Blair J.R., and Hutton R.C. (19781, Hornsby B. and Sullivan B.J. (1978), and Alexander E.G. and Fabjanczyk M.W (1981). As many as thirteen open stopes may be producing concurrently in the Orebody (Figure 2). The multiple silver-lead-zinc orebodies containing reserves of 54 million tonnes of 150 g/t silver, 6.4% lead and 6.5% zinc, are mined by open stoping, and cut and fill techniques. These methods have been documented by Goddard I.A. and Bridges M.C. (1977 1, and Goddard I. A. (1981 1. Only the ventilation of the 1100 Orebody open stopes will be discussed. However, the same ventilation philosophy is employed in open stope design in the lead orebodies.

Jan 1, 1981

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

By T. McCallum

Crud is a common concern in SX processes and is formed as a complex solid stabilized emulsion of aqueous and organic.1,3 Crud formation is highly dependent on the amount of solids entering the circuit and is influenced by a number of other operational factors. A common practice for crud processing is interfacial pumping, wherein crud, organic, and aqueous are pumped from the settlers for treatment and utilizes a variety of equipment. These mechanical means of crud processing are effective, however, require significant processing time and require oversight to prevent the return of contaminated organic. Cytec has developed a unique crud treatment process utilizing both chemical and mechanical means to enhance the solid/liquid separation. The use of ACORGA CB? 1000 crud busting reagent allows a rapid separation of solids from the organic phase and provides similar volume recovery to current practices. The process allows operations to return clean organic back to the plant more efficiently and may enable operations to process more crud. In addition, the organic quality of the recovered organic is higher than that recovered by typical means, which can lead to operational cost savings.

Feb 27, 2013

By Gregory J. Chekan

In This Chapter [Drilling, blasting, and crushers Diesel particulate Enclosed cabs Ventilation with jet fans Stopping construction methods Propeller fans as main fans] This chapter explains how to control dust in large-entry stone mines, including both silica dust and diesel particulate. Most stone mines are limestone mines, but a substantial minority are marble, sandstone, and granite mines. These mines differ from most others in that entry widths are 30 ft or more and entry heights are 25 ft or more. Such mines, developed with room-and-pillar methods, have large open areas that can make ventilation and dust control more difficult. Because of the difficulty of ventilating stone mines, improved ventilation is a major focal point of this chapter. However, the chapter also covers the control of dust from drills, blasting, and crushers. Another part of the chapter covers enclosed cabs, an effective dust control technique for some workers. BACKGROUND The major dust compliance problem in stone mines is caused by silica (quartz) in the rock. Mines in high-silica rock, 8% or more, are far more likely to have a dust problem than those where there is less silica. Geographically, the limestone in the Northeastern and South Central United States has higher silica than the rest of the country. Chekan and Colinet [2002] have analyzed Mine Safety and Health Administration (MSHA) dust sampling results [MSHA 2001] from the stone industry. They have concluded that, on average across the United States, the workers exposed to the highest dust concentrations are rotary drill operators, front-end loader operators, truck drivers, and crusher operators. However, there are many regional differences. Also, occupations that work outside of cabs, such as blasters, roof bolters, and laborers, can be exposed to high dust levels.

Jan 6, 2003