Search Documents

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By Kenneth R. Maser

This report describes a research and development program sponsored by the United State s Bureau of Mines. The purpose of the program was to develop reusable explosion-proof bulkheads for a cross-cut emergency shelter, and to study the implementation of such bulk-heads, and the resulting shelters, as part of an emergency escape plan in a normal coal mining environment. The first part of this report reveals a number of significant conclusions regarding the application of emergency shelters. A study of the cause s of, and the conditions prevailing during a mine emergency indicate s that ideal placement of the shelter s would be midway along developing entries, and at the inter section of butt and main entries. The proper spacing of shelters is based on the travel capability of trapped miners, which is in turn dependent on the height of coal. The life of a given emergency shelter, based on an analysis of the above information, will be anywhere from 6 months to 10 years. Consequently, some shelters are regarded as "temporary?, while others "permanent?.

Jan 1, 1975

By Foster Fraas

Almost all minerals show irreversible changes in electrical conductivity after heating in the temperature range 100° to 800° C. This effect can be detected with only a limited number of minerals with the standard ionizing-electrode-type separator, which differentiates between nonconductors and conductors in the single-particle resistivity range of 1011 to 1013 ohms. Tests outside this range with other type separators, such as the static field type, increase the number of minerals with which the effect can be detected to almost all that were tested. Irreversibility may be the result of an alteration of adsorption layers, volatilization of surface cations or anions, or an oxidation or reduction. One example is limonite, which decomposes to hematite and passes through two minima and two maxima in conductivity in the temperature range 100° to 900° C.

Jan 1, 1959

By Leslie S. Weldon

THE Lake Shore mine has been developed by two vertical shafts, with level intervals at 200 feet to the 2200 level and at 125 feet below this horizon. A main cross-cut joins the two shafts on all levels to the bottom of No. 3 shaft, and opening into these cross-cuts are the ore passes and sand passes, which are completed from surface To the 4450 level. In the west part of the mine, additional connections have been made between No. 1 and No. 2 veins, through which the major part of the ore from No. 2 vein west is routed to drifts in No. 1 vein. With the lesser amount of stoping on No. 1 vein, this arrangement permits better haulage to be maintained. The ore passes are driven at 50 degrees from the ends of short cross-cuts off the main ones and are broken through to the levels above at the mouths of the short cross-cuts, to allow for dumping on each level. The passes are controlled at each level by ball-and-chain gates and deliver to crushers and thence to loading pockets, shown in Figure 1. That system is quite flexible in that it is possible to by-pass the crushers at any station and load from either shaft at a number of different pockets. The sand passes are driven from the main cross-cuts at the same inclination as, and parallel to, the ore passes. Each is equipped with a chute and dump hole, so that waste or sand fill may be loaded or dumped at each level. A transfer door, hinged on the bottom, is installed opposite the chute for by-passing fill from one level to the next, and in the closed position protects the opening at the top of the pass. The dump hole situated beside the transfer door is protected by a grizzly with 10-inch spaces. Waste rock may be withdrawn from the system through No. 3 shaft loading pocket at the 2950 level to a waste bin on surface. Levels are developed by drifts in No. 1 and No. 2 veins for their entire lengths. Subsidiary breaks are followed at a later date, when full information has been obtained by exploration, and a considerable amount of development by sub-drifts is carried out in the upper part of the mine, particularly in more or less erratic sections of No. 1 vein.

Jan 1, 1936

By S. G. Kumar

The performance of nickel based high temperature materials is directly related to their microstructure, which is controlled by the various processing steps. Nickel base alloys are melted and refined by a variety of processes that include Vacuum Induction Melting (VIM), Vacuum Arc Remelting (VAR) and Electroslag Remelting (ESR). The limitation of VIM is that the metallrefractory reactions lead to the disintegration of the crucible and hence contamination of the product due to macrosegregation. This macrosegregation is alleviated to some extent by controlling the solidification in VAR. The main attraction of ESR is its ability to produce a clean product by controlling the deleterious inclusions. In recent years Electron Beam Melting (EBM) is emerging as an alternative to the VIM, VAR and ESR. This paper reviews the current status of these processes and outlines the scope for further improvements in the processing technology.

Jan 1, 1993

Commodities statistics and other information are available through the following three systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By E. D. Gardner

This bulletin, which discusses open-cut mining at the metal mines of the United States, is the last of a series of such papers by the Bureau of Mines describing the principal methods of mining.4 Open-cut mining is applicable to flat-lying mineral deposits relatively near the surface. Vein deposits seldom are amenable to this method, although outcrops of veins sometimes are worked as open pits. Most of the iron ore of the country is mined from open pits; according to the Minerals Yearbook, 67.4 percent was mined from open pits and 32.6 percent from underground mines in 1937. Open-cut mining is relatively new in the copper industry but yields more copper than any other method; in 1937 about 52 percent of the copper ore mined in the United States was taken from open pits. Lead-zinc ore has been produced from open pits in the Joplin (Mo.) district, but most of the deposits in this area, although flat-lying, are too deep to be mined economically by the open-cut method. In 1937 one company at Oronogo, Mo., was stripping overburden and mining mixed oxidized and sulfide ores by this method.

Jan 1, 1941

By Donald Giroux

This report documents the design, fabrication, testing, and coal mine demonstration of a hopper-feeder-bolter during a four-phase program for the U.S. Bureau of Mines. The machine was designed to increase productivity and safety in under-ground room-and-pillar mining. It performed well as a hopper-feeder for continuous haulage during a coal mine demonstration. Testing in a simulated mine showed that the machine also has good roof bolting capability.

Jan 1, 1987

By W. R. Hardwick

This paper describes mining methods and practices of the Chino Mines Division, Kennecott Copper Corp., Grant County, N. Mex. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A similar program was conducted from 1928 to 1939, which helped to improve the efficiency of mining operations. The primary purpose of the program is to promote development and conservation of our mineral resources by disseminating technologic information on methods, practices, and related features in mining mineral deposits. It is expected that the program will: (1) Promote efficiency in operating mines; (2) assist operators and engineers in evaluating and developing new mineral deposits; (3) provide data for engineering curriculums in mining schools; and (4) furnish performance and cost data for revising engineering handbooks and for inclusion in engineering textbooks.

Jan 1, 1958

By Michael L. Clar

This volume is an annotated bibliography of published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines. This literature was used to develop Volume 1 of this report, which assesses the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. Each abstract is followed by subject descriptors. the abstracts are listed alphabetically by title and are numbered consecutively. These numbers are used in the subject index to help the reader locate the appropriate articles.

Jan 1, 1981

By Oliver Bowles

This report covers the character, properties, origin, occurrence, and uses of the traprocks and describes briefly the methods and equipment employed in quarrying and preparing them for market. Production of traprock occupies an important place in industry. In 1960 the output in the form of crushed stone reached nearly 58 million tons valued at $87 million. Traprocks are also shaped into blocks of dimension stone for monuments, building construction and decoration, and specialized products such as surface plates.

Jan 1, 1963

By Oliver Bowles

This report covers the character, properties, origin, occurrence, and uses of the traprocks and describes briefly the methods and equipment employed in quarrying and preparing them for market. Production of traprock occupies an important place in industry. In 1960 the output in the form of crushed stone reached nearly 58 million tons valued at $87 million. Traprocks are also shaped into blocks of dimension stone for monuments, building construction and decoration, and specialized products such as surface plates.

Jan 1, 1963

By James Paone

This report on the state of the art of horizontal boring technology for underground power transmission installations was prepared by the Bureau of Mines at the request of the Department of the Interior. This paper describes the different machines and methods used in augering, impacting, pushing, drilling, and machine tunneling horizontal holes through soil and rock. A review of the borehole survey and guidance tools and techniques applicable to these methods is also given. Nonboring methods used for emplacement of power distribution and transmission lines are briefly discussed. The paper ends with a brief technical forecast, an analytical summary of the state of the art, and recommendations based on power industry needs. Horizontal boring techniques for power distribution lines installation are adequate to meet the requirements of the power industry, particularly where such burial involves relatively short distances in soil or soft rock. For burying power transmission lines, particularly in the harder rocks and over relatively long distances, horizontal boring methods are not as well advanced. Research and development as well as economic incentives to equipment manufacturers could substantially improve the state of the art. Obstacle detection and guidance systems for directing boreholes to specified targets need major improvements to meet the requirements of the power industry for underground burial of distribution and transmission lines

Jan 1, 1968

By Edmund J. Korber, Donald E. Raab, Frank A. Burns

During the early 1960s, the advent of self- advancing longwall roof supports triggered serious consideration by Bethlehem management to introduce the technique of longwall mining at one of our central Pennsylvania coal mines. Although longwall mining was initially justified as a means to cope with the severe roof conditions at our Mine 32 (Watson, B., 1971), the result of the endeavor has been a consistent and reliable level of coal production, first from Mine 32 and then later from Mine 33, over a period of fifteen years. Longwall production from the Cambria Division has been the mainstay of the low volatile coal required by Bethlehem Steel for steel production. Let us review the events that led to this accomplishment, as well as where we stand today.

Jan 1, 1981

By R. A. Cattell

Continuing progress in a petroleum and natural gas research program of world-wide significance makes it difficult to pinpoint accomplishments within definite time limits, and it is helpful to look back as well as forward in attempting to introduce and summarize the petroleum work of the Bureau of Mines in the fiscal year 1953. The 1952 report2 / indicated progress in a long-range program applicable in large part to both defense and peacetime requirements. The present report indicates a continuation of that program, modified partly by new demands and interests of government and industry, and is highlighted by a number of significant contributions to the knowledge of petroleum and natural gas and their production and utilization. The intent of the program was clearly epitomized in a statement made near the end of the fiscal year at a general conference of Bureau of Mines personnel where the record was critically reviewed:

Jan 1, 1955

"The mission of the Respirable Dust Center is to enhance the health, safety and productivity of the miners 'through advancing the fundamental .understanding of all aspects of respirable dust associated with mining and milling and the interaction of dus.t and lungs for reducing the incidence and severity of respirable dust disease. All Dust Center activities are focussed to be responsive to this mission which is shared by several federal agencies closely associated with the Generic Mineral Technology Center for Respirable Dust such as USBM, M,SHA, and NIOSH, and the mining industry. While significant progress has been achieved in making mine atmospheres cleaner and healthier, respirable dust disease remains the nations worst industrial hazard. GOALSThe goals of the Respirable Dust Center have been formulated to recognize the diverse scientific, engineering and medical aspects of respirable dust as well as the need to enhance the interaction, education and technology transfer in the respirable dust area.The Center goals are to:1. Enhance the understanding of the scientific, engineering and biological characteristics of fine and respirable mineral particles, fibers, organic aerosols, and complex particles found in the mining and milling atmospheres.2. Advance the understanding of the physical behavior of airborne respirable dust particles in flowing streams under different. stimuli during mining and milling.3. Advance fundamental understanding of the causative mechanisms for the occupationally related lung impairments and the airway diseases of mine and mill workers.4. Establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment and control measures) in the generation, exposures, and pathogenic properties of fine particles.5. Contribute to the development of control mechanisms for reducing ambient respirable dust concentrations, worker exposure, the incidence and severity of dust related lung disorders and disease prevention in mining and milling atmospheres.6. Enhance functional integration among the various research personnel in the Center, as well as, with other groups, such as MSHA, NIOSH and USBM involved in respirable dust research and control.7. Develop technically trained personnel for employment in the mineral industry for respirable dust research and control.8. Enhance the availability of respirable dust-related information utilizing several technology transfer avenues."

Jan 1, 1990

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960

By Joseph A. Holmes

The investigations carried on at the fuel-testing plant of the United States Geological Survey at St. Louis in 1904-1907 included tests of the steaming and gas-producing qualities of many coals and of the possibilif3 of their improvement by briquetting, together with washing and coking tests and tests of some of the resulting coke in the cupola. These tests were part of a general inquiry into the manner of utilizing most efficiently each of the coals under investigation. The equipment used in the cupola tests of coke, the manner of conducting the tests, and the essential results have been described in publications of the Geological Survey," and only the more important conclusions to be drawn from the tests are mentioned in the following pages. The tests were made to show the fitness of the cokes for foundry purposes, but an incidentlll result was to show foundry men and the coke producers the advisability of studying the conditions of foundry practice. The present bulletin, published by the Bureau of Mines because the analyzing and testing of fuels have been transferred from the Gilological Survey to the Bureau of Mines, briefly reviews the status of the coke industry, some features of practice in the use of coke in the foundry, the probable happenings of a cupola heat, and the reasons for modifying charging practice so that a particular coke can be used to best advantage.

Jan 1, 1910

By J. R. Thoenen

Up to 1914 almost all of the world's supply of potash came from Germany and Alsace. With the cessation of shipments from Germany during the World War the importance of a domestic suppler was evident. During the past 15 years the United States has been working toward the establishment of a domestic potash industry which would end foreign dominance in this commodity. The Federal government has taken an active part in this program. As its share in the work, the Bureau of Lines has ascertained the potash resources in certain district's through core drilling and has engaged in a comprehensive program of research on the extraction of potash from its various minerals. Until the passage of the Winter bill (H. R. 496) by Congress in 1928 the Bureau of Mines had not been able to give any consideration to the western ores, wyomingite (leucite) and alunite. With the massage of this bill, however, the ray was opened for the extension of the potash studies to cover these materials.

Jan 1, 1932

By M. S. Fleming

The objective was to evaluate central lubrication systems for potential use on underground mining equipment. Previous use on continuous mining equipment resulted in poor system performance because of improper selection of lubricants, component failures, and an inconsistent delivery of lubricant to the bearings. The principles and operational characteristics of systems are reviewed and evaluated, and it was concluded that systems are available which can provide reliable central lubrication if properly applied, installed, and maintained. The procedures for applying a system to a continuous miner are discussed. Investigation revealed the lack of significant information on lubrication-related equipment failures and injuries related to maintenance and repair operations, the lack of significant failure rate data for central lubrication system components, and the lack of performance standards for central lubrication systems and components. To continue the development of systems for underground mining equipment it is recommended that a data bank on failures and reliability for equipment with and without central lubrication systems be created, and standardized specifications and performance criteria be developed for central lubrication systems and components which will be used on underground mining equipment.

Jan 1, 1979