Search Documents

By Enrique Hauser

FiRE-damp is a mixture of methane with other inert gases or combustible gases. The inert gases in question are carbonic acid, water vapor, nitrogen, etc. The combustible gases are hydrogen, ethane, etc. The study of the properties of fire-damp, therefore, becomes a study of the properties of methane and the influence on its properties of the different gases we have mentioned. Characteristic Properties of Methane 1. Respirability.—Methane being a paraffin is characterized by its weak chemical affinities. Prom the physiological point of view one could substitute it for nitrogen of the air at least momentarily, without experiencing any difficulty in breathing the mixture consisting of 21 per cent. 02 + 79 per cent. CHI. I have tried this on myself, making the gas exhaled from the lungs burn subsequently in a Bunsen burner.' From the chemical point of view, this weak affinity permits the gas to be burned in certain circumstances with hydrogen and oxide of carbon in an oxygenated mixture, with the result that the last two gases achieve only a fractional combustion. This practice has been utilized with success in the methods of analysis which I have perfected and which I describe later in this paper. 2. Retardation of Flashing Point.—A characteristic property of methane is its retardation of flashing point, noted by Davy in 1816 and studied by Mallard and Le Chatelier in 1883.2 Taffanel and Le Floch have recently confirmed these results.8 Let us recall the nature of this retardation: When a mixture of combustible gases with air or with oxygen is

Jan 1, 1916

The New Broken Hill Consolidated Airshaft is the first major undertaking in the development of New Broken Hill Consolidated Ltd's. property, which adjoins that of The Zinc Corporation Ltd. on the latter's southern boundary.The Zinc Corporation ore-body has a southerly pitch. The Zinc Corporation's New Main Shaft is 1000 ft. north of the common boundary, and the general plan of development of the New Broken Hill Consolidated property is by driving south from this shaft on the lower levels. No downcast airway from the surface was available south of the Zinc Corporation's New Main Shaft; this shaft acts as the main downcast to the bottom of the Zinc Corporation mine, the general air flow then being northward and upward to the upcast shaft at the extreme north end of the Zinc Corporation property.Rock temperature is 920 F. at 2000 ft., increasing by 10 Fahr. each 72 ft., the rock temperature at 3000 ft. being estimated at 1060 Fahr. With the general air flow northward from the Zinc Corporation's New Main Shaft, adequate ventilation under these temperature conditions would not be practicable for any great distance south of this shaft without another main airway from the surface. Accordingly the New Broken Hill Consolidated Airshaft is being sunk at a point 1000 ft. south of the common boundary, i.e., 2000 ft. south of the Zinc Corporation's New Main Shaft, to ventilate future New Broken Hill Consolidated workings and that part of the Zinc Corporation mine between the boundary and the New Main Shaft.

Jan 1, 1940

By Jack Barrett

The oxidants which participate in the bacterially catalyzed oxidation of minerals are dissolved oxygen and some aqueous iron(III) complexes. Speciation studies indicate that these complexes consist of iron (III) -sulfate and iron (III) -arsenate ions. The complexes have different oxidizing powers as indicated by their calculated standard reduction potentials. The thermodynamics of the oxidations of pyrite and arsenopyrite are related to the mechanisms of the reactions. The mechanisms are discussed in terms of primary processes occurring on the mineral surfaces and the secondary reactions of the primary products. The importance of the conclusions to plant operation is discussed.

Jan 1, 1993

By James B. Pfeiffer

TETRA Technologies, Inc., has applied its HDS? metals precipitation system to control a mine drainage problem. The effluent from the mine contains primarily zinc, manganese and iron, plus varying small amounts of cadmium, copper and lead. The flow from the mine averages 350 gpm, and varies considerably depending on season and weather conditions. The plant was designed to treat 1000 gpm of the water and generate a dense sludge suitable for recycling. The HDS? system contains a number of reactors, followed by post filtration and meets stringent metals discharge criteria as specified by New Source Performance Standards.

Jan 1, 1994

By M. Akser

Ilmenite, rutile, and zircon deposits of commercial importance have not been reported to-date from Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit along the Black Sea coast of Turkey in the vicinity of Ormanli, northwest of Istanbul. Consequently beach and sand dune samples were collected from that area for additional analysis. Laboratory methodologies, designed to simulate standard industrial heavy-mineral plant practices, were used to analyze and evaluate the samples. Based on the analyses, and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1995

By David E. Nicholas, Steven R. Dismuke, Paul F. Cicchini

The Buick mine, located 195 kilometers (120 miles) southwest of St. Louis in the Viburnum Trend, is owned and operated by Homestake Mining Company. The mine produces lead and zinc ore from a room and pillar mining method at a depth of approximately 335 m (1 100 ft). The Buick orebody typically averages 60 to 120 m (200 to 400 ft) in width with ore thicknesses ranging from 2.4 to 36.6 m (8 to 120 ft). The mine is divided in two; the halves are referred to as the North mine and South mine orebodies. The North mine orebody contains the higher grade ore; however, the developed reserves for the South mine orebody comprise about 60 percent of the total developed reserves for the Buick property. Existing pillars represent one-third of the total developed reserves.

Jan 1, 1986

By James S. Browning

Heavy liquids have been used to separate minerals of different specific gravities for many years.4 5 6 7 8 9/ The method permits substantially quantitative evaluation of a variety of minerals and requires much less time than the usual methods of chemical analysis. This Bureau of Mines investigation was conducted to determine the applicability of heavy liquid mineral separation to the evaluation of certain spodumene and kyanite ores, prepared mixtures, and plant products. After careful standardization of the particular mineral and associated gangue, estimates of chemical analyses could be obtained from results of heavy liquid separations.

Jan 1, 1960

By T. Dombrowski

Acid-activated montmorillonite is used worldwide as a catalyst and as a sorbent for the enhancement and purification of petroleum products as well as vegetable and animal-based fats. The solid-acid character of the activated montmorillonite is imparted by the manufacturing process, giving it unique properties that are exploited in these industries. Several international companies and a multitude of local clay producers are focusing on improving the efficiency of their standard and specialized products. This paper will describe the use of acid-activated montmorillonite in traditional sorbent applications, as a solid acid catalyst, and other new uses.

Jan 1, 1997

By J. Kern, T. F. Torries

Identifying high value areas of unmined coal when large quantities of coal are available relative to annual markets is difficult because of the uncertainty of when the coal is to be mined. A GIS based methodology developed to value reserve coal in a producing coal region for the purpose of ad valorem taxation also identifies high value areas for mining investment. The methodology is unique in that it accounts for most mining, environmental, and market factors to determine when specific properties are to be mined. The methodology and data base are useful for directing regional exploration and acquisition activities toward most favorable areas.

Jan 1, 1999

By J Tibbett, F T. Suorineni, B Hebblewhite

Block caving is an important mining method for the future economic exploitation of large, low-grade, steeply dipping orebodies. While block caving is not a new method, there are still many unknowns surrounding the mechanics driving the process, particularly as we are forced into deeper, higher-stressed and stronger ore deposits. The caving industry is desperate to provide some explanation behind the myths of caving geomechanics to better predict and manage current caves and caves of the future. Large amounts of data are collected to help understand caving, but it is not fully utilised and current approaches for analysing the data are capacity limited. The application of virtual reality and scientific visualisation (VRSV) technology to visualise and analyse block caving is a critical future component in the assessment toolbox. VRSV enables large, complex, multidimensional data sets to be analysed and the power of human visual problem solving processes to be utilised. Block caving is a complex system and needs to be analysed as a system, rather than looking at individual factors one at a time. A software module has been developed at UNSW Australia for use in the advanced visualisation interactive environment for analysis of the block cave mining system (BCMS). This fully immersive, 3D virtual assessment tool shows exciting potential and is used to analyse the BCMS with a close linkage to time (ie the chronological occurrence of data). This tool will enable a true investigation into the cause and effect relations within the BCMS. Current research is investigating Newcrest Mining Limited’s Ridgeway Deeps operation and is aiming to turn some of the cause/effect relationships into increased geomechanics understanding to provide improvements to ground control management. This paper outlines the methods of assessment used to analyse BCMS geomechanics with VRSV and shows the potential of the software module for BCMS analysis.CITATION:Tibbett, J, Suorineni, F T and Hebblewhite, B, 2014. The application of virtual reality technology and scientific visualisation to the understanding of block cave mining systems, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 195–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By W. E. Anderson

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at thirteen mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing buckets ranging from 30-to 220-cubic-yard capacity, were documented. We have judged that U.S. surface coal mining draglines, 30 yards and larger, can be represented as 120 machines having 60-cubic-yard buckets, moving 1.8 x 10 yards of overburden during 6,650 hours of productive availability per year. Based on our limited field study, we have calculated that downtime resulting from rope-related causes averages 105.6 hours per year for each (typical 60-yard) dragline. The total lost production from this source alone is thereby estimated at about 25 x 10 yards annually. Although study findings did not reveal anything about dragline rope life that wasn't known or practiced by one operator or another, most operators could expect improved rope life by periodic review of their practices and by adopting or adapting one or more life-improvement measures employed at other sites. Since rope productivity was found to vary by about five to one, among the sites studied, we believe considerably improved average performance is possible. As little as ten percent overall improvement would mean increased national productivity exceeding two million yards of solid overburden removal, and associated savings in rope costs alone of some two million dollars annually, not to mention any reduction of labor-related expenses. This report outlines preliminary findings which may prove useful to many operators in extending wire rope life, thereby lowering expenses and increasing surface coal mining productivity. Some of these modifications or adjustments in maintenance/operating practices would not require capital investment. We did not find anyone who had tried cost reductions by using presocketed dump

Jan 1, 1977

By R Jaine, D Strang, M Fowler

"This paper presents a case study demonstrating active geotechnical pit slope management at the now completed Carina Iron Ore Project operated by Mineral Resources Ltd (MRL). The site is located 105 km north-east of Southern Cross, Western Australia. The paper is primarily focused on the slope stability failure modes and the remedial measures employed to maintain mining.Between a quarter and a third of the excavated slopes were impacted by some form of instability that was beyond expectations of the intended slope design criteria and common practice. Ongoing mining was supported by intensive geotechnical pit slope management including close cooperation between geotechnical, mine planning and operations staff to achieve timely and practical mining solutions.Mining encountered varied slope failure mechanisms which required a combination of remedial solutions comprising: horizontal depressurisation holes, deferral of excavation, unloading, buttressing and catch berms.The root cause of the challenging slope performance was a mismatch between the predicted and encountered geotechnical model, resulting from a failure to recognise the critical mechanisms that control slope stability.Despite the extensive zones of instabilities at completion of mining, full ore recovery was achieved without major delays and in a controlled and safe manner.Citation:Fowler, M, Strang, D and Jaine, R, 2016. Adapting to Geotechnical Change - a Case Study of the Carina Open Pit Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By W. M. Armstrong, John A. H Lund

The paper describes an investigation of some of the tensile properties of single crystal vanadium, poly-crystalline vanadium and polycrystal-line tantalum, in the range of: W°C to -196°C. Techniques employed in the preparation and testing of specimens are discussed in detail. Some results of determinations of the temperature dependence of yield stress and ductility are given, and discussed in terms of the Cottrell-Bilby Theory of yielding. At subnormal temperatures, all the body-centred cubic transition metals in the Periodic Table exhibit; a) the "yield phenomenon" in tension, b) a strong temperature and strain rate dependence of yield stress, and c) a large decrease or complete loss of ductility. The yield phenomenon (existence of an upper and lower yield point) has been explained by Cottrell and Bilby ( 1) in terms of the dislocation-locking effect

Jan 1, 1961

By W. Standifird

"Cohesive fracture is a mechanical model widely used for modeling quasi-brittle fracture in rocklike materials. This work discusses use of this model to simulate quasi-brittle fractures generated by injection stimulation during the process of cuttings reinjection in West Africa. Cuttings reinjection is an engineering practice used for disposal of drilling waste. During this process, hydraulic fractures are created at the target formation and milled cuttings are injected with fluid. In practice, this process must remain in compliance with environmental regulations and zero-discharge policies. The purpose of this study is to determine the following factors of injection design for a field in West Africa: (1) pumping pressure capacity required to successfully perform the injection and (2) the injection rate for injection performance and the value of fracture width under injection.A simplified three-dimensional (3D) finite element model (FEM) was built. A poroelastic plastic damage model was used for simulation of the cohesive crack prorogation within the target formation. For simplicity, fracture development in both horizontal and vertical directions was simulated separately. In this way, the computational burden for one calculation was reduced to a reasonably low level, without losing accuracy of the model. Loads of the model include fluid injection and gravity, which balances the initial geostress field. Various values of injection rate were used in these calculations to determine the most reasonable value of injection pressure. The capacity of pressure of a pumping device was determined using this optimized value of injection pressure.Results in values of width and length of fractures created by the injection are presented. Injection pressures at bottom-hole (BHP) corresponding to each value of injection rate are also given. Numerical results for fracture generation and propagation in a horizontal direction were visualized. The pumping pressure capacity required to fulfill the cuttings reinjection work was determined based on the numerical results of optimized injection rates and pressure. The fracture width was determined using the given pumping pressure. The length and height of the fractures was determined using pumping pressure along with the required volume of cuttings waste to be disposed of into the formation.This work presents a case study of 3D finite element modeling of hydraulic fracturing generated by cuttings reinjection. The results of the optimized injection rate and pressure provide a best practice and a useful reference for cuttings reinjection analyses in this region."

Jan 1, 2015

By James H. Barks

Exploration for ore deposits in southeastern Missouri in the 1950's resulted in the important discovery of lead, zinc, copper and silver in 1955. Further discoveries in the area led to the naming of the Viburnum trend. It has sometimes been referred to as the "New Lead belt" to distinguish it from older lead-producing areas to the east. As presently developed, the "trend" is 35 miles long, running north and south about 50 miles west of the Lead belt. Galena (lead) is the principal ore mined, with lesser quantities of sphalerite (zinc), chalcopyrite (copper) and silver recovered as economic by-products. The ore body is as much as 140 feet thick and 1,200 feet wide, and is found in the Bonneterre Dolomite (Upper Cambrian) at depths ranging from 700 to 1,200 feet. Since its discovery many companies have engaged in exploration and several major companies have developed new mines and constructed mills and a smelter in the area. The first mine in the Viburnum trend came on stream in 1960, but as more mines came on stream and others reached capacity, lead production increased to the point that the Southeast Missouri Lead district produced 432,576 tons of lead in 1970 to become the world's largest lead-producing region (Missouri Geological Survey and Water Resources, 1971). The Viburnum trend area with its rolling, heavily forested hills and numerous clear running streams is in the Clark National Forest of the Missouri Ozarks. Until the recent development of its mineral resources, the area was sparsely populated and nearly unmarked by the activities of man. Industrial development is almost certain to be accompanied by environmental changes. In a day of growing awareness of the need to preserve the quality of the

Jan 1, 1971

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015

By E. L. Bruce

Red lake is a body of water some thirty miles in length lying about forty miles northwest of the outlet of Lac Seul. It forms one of several large lake expansions on a river which enters the English river from the north, twenty miles below Lac Seul. Before the construction of the National Transcontinental railway a long canoe journey was necessary to reach that part of the English river, and Red lake, two days travel beyond, was one of the furthest outposts of the trading companies in that difficultly accessible triangle of country between Lake Winnipeg, James Bay and the English and Albany rivers. The Hudson's Bay Company post at Red lake is said to be one of the earliest established in the district but there are no records at the post, and as the English and Albany rivers never were used to any great extent as travel routes there is no mention of the place in the diaries of any of the early explorers. Dr. Bell passed through Red lake on his excursion to the Berens river country in 1883, and a brief note mentions that Huronian rocks were seen. To Dr. Dowling, however, belongs the credit for the first thorough description of this basin of sediments and basic volcanics. In 1893 he followed the course of Dr. Bell's trip, of ten years previous, through Red lake to the upper part of the Berens river.

Jan 1, 1926

By C A. Brannon, C A. Dipas, H A. Vega, D Villa

The development and construction of the Grasberg block cave mine (GBC) is in progress, currently targeting initiation of caving in late 2018. Current production planning anticipates ramping up to full production of 130 000 to 160 000 t/d by 2027. As GBC approaches the production phase, there is a high priority on increasing the accuracy and level of detail in the production plan. The advance of the cave front directly controls the drawbell opening rate that is achievable. Therefore, an essential component of this plan is to produce an undercutting and drawbell sequence that honours the caving parameters that have been set for the mining blocks by the GBC production planning team.The PT Freeport Indonesia (PTFI) mine planning team and the Geovia caving business unit have developed a computational tool (Undercut Tool) capable of generating an undercutting sequence that follows a set of caving rules, such as advance rate per tunnel, maximum blasted area per period, control of lead-lag and shape of the undercut face. This tool also produces a drawbell sequence that honours the undercutting advance sequence, which is ultimately used to generate a life-of-mine production plan. This paper describes the inputs and outputs of the Undercut Tool that have been used to compute the long-term production plan for the GBC mine. It will further describe how the Undercut Tool takes into account operational constraints and geotechnical considerations that must be considered when developing a defendable production plan. Included is a discussion of the initial results of the planning outcomes from the tool; it will demonstrate how this work will support specific aspects of the plan such as the detailed undercut production drill and blast plans for the drill ring sequence, as well as how that plan will drive the drawpoint opening plan.CITATION:Villa, D, Brannon, C A, Dipas, C A and Vega, H A, 2017. Integrated drawbell and undercut scheduling using a computational tool at the Grasberg block cave mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 271–276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By E. W. Mountjoy

THE Exshaw formation is a thin but very persistent black shale unit generally well exposed along the easterly scarp faces of the fault blocks comprising tl1e front ranges of the Rocky mountains. It is over lain by the Mississippian Banff shales and silty shales and underlain by the massive Palliser Limestone formation of late Devonian age. The Exshaw continues eastward under the plains of Alberta and on into Saskatchewan, with little change until it reaches the surface of the Palaeozoic-Mesozoic unconformity. During the summer of 1953, the writer was working- with a field party under Dr. J. L. Usher in the front ranges of the Alberta Rocky mountains. This party, sent out by the Mobiloil Company, conducted a geological survey of Devonian rocks between the towns of Banff and Jasper. The writer helped to describe and map these Devonian rocks and obtained first-hand information concerning the Exshaw shale and its relationship to the underlying and overlying sediments. Additional information was obtained from reference material and from a number of geologists whom the writer has consulted. Grateful acknowledgment is offered to them, to the Mobiloil Company for releasing field information, and to F. W. Beales and W. P. Hancock who helped edit the original paper for publication. Information from areas north and smith of that studied and from bore holes on the prairies is referred to. Localities mentioned may be found in Figure 1.

Jan 1, 1956

By A. Manohar Rao

Underground mining in general and more so the coal mining is a hazardous venture as it is a struggle against nature and natural forces. The stability of roadways has a direct impact on production and productivity. The roadway stability can be strongly influenced by the direction of the drivage. The stress studies are useful to provide a frame work for understanding the influence of drivage direction on roadway conditions, and to illustrate how mapping techniques can enhance this understanding. The act of mining can concentrate and re-orient the original stresses. Whenever coal is removed, the overburden weight that it carried is transferred. Vertical stresses are similarly affected when the roof is deformed or failed. The Singareni Collieries Company Ltd., a joint Public sector undertaking of the Government of Andhra Pradesh and India is conducting coalmining operations in the Godavari Valley Coalfield and is catering to the needs of a large part of South India. With the technology update, it is looking for safe mining and to achieve higher production. As a part of this, an attempt is made to understand the stress conditions prevailing on the mine blocks by different ways and means in terms of geology, structure and tectonics of the Godavari Valley coalfield, satellite imagery studies, cleat pattern, stress measurement studies conducted in different mine blocks, and stress mapping technique.

Aug 1, 2013