Search Documents

By A. E. Bellis

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operations. Hundreds of dollars' are spent in the design and manufacture-of milling cutters of special form ,for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring the tool out "clean," is a difficult: one and calls for no small amount of skill. In order to be on the safe side, the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be-protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed steel, in which metallographic means were used to determine the correct hardening temperatures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accompanying table. Six specimens from the same bar :of each: kind of steel

Jan 1, 1917

By S. Yokoya

With increasing requirement of steel productivity and quality in continuous casting in the conventional casting system using an immersion nozzle, it is very difficult to establish a reasonable molten flow pattern. In order to overcome this difficulty, we propose a new method of imparting swirling motion onto the flow in the immersion nozzle and to control the flow pattern in the mold. Following results have been obtained during the studies. For the case of slab continuous casting mold: High amplitudes of oscillation with a period of 10 to 15 seconds are observed in the outlet flow of the immersion nozzle and meniscus flow in the conventional casting system, while these phenomena are remarkably suppressed using swirling motion in the immersion nozzle, which leads to very calm and uniform flow pattern at the outlets of the immersion nozzle, in the mold and on the meniscus in the mold; For the case of billet continuous casting mold: (1) heat and mass transfer near the meniscus can be remarkably activated compared with a conventional straight type immersion nozzle without swirl, and (2) Quite different mold flow patterns are observed between the divergent and straight immersion nozzles. Heat and mass transport in the mold using the divergent nozzle is much more reasonable compared to that of straight nozzle. The findings, mentioned above, are very useful to control the flow pattern in the slab, and billet continuous casters. Such effectiveness of swirling flow in the SEN on the mold flow has been put into practical use. As a result, remarkable progress on the quality and production of continuous casting products has been observed in practical application.

Jan 1, 2006

By A. E. Bellis, T. W. Hardy

The problem of heat treating high-speed steel becomes more and more important as the design of cutters becomes more and more complicated in increasing the efficiency of mechanical operatioqs. Hundreds of dollars are spent in the design and manufacture of milling cutters of special form for rapid production of duplicate or interchangeable parts, and then, as the heat treatment is faulty on the one hand, or scientifically executed on the other, the tool fails after a few operations, or its efficiency is greatly increased. The practical operation of giving these complicated tools the right temperature necessary to bring out the best cutting qualities, and at the same time bring-the tool out "clean," is a difficult one and calls for no small amount of skill. In order to be on the safe side the average tool hardener uses a temperature much too low to give the best results with the high-speed steel he uses. In the case of cutters which are finished to a given diameter before hardening, it is impossible to grind the tool after hardening, so that it is essential that the surface be protected from oxidizing or de-carbonizing. It is the aim of this paper to describe some experiments on hardening high-speed stee1, in which metallographic means were used to determine the correct hardening tempcratures. The accompanying table and plates show the results of hardening experiments on five different high-speed steels. The analyses for carbon, tungsten, chromium and vanadium of each steel are given in the accom- . panying table. Six specimens from the same bar of each kind of steel

Jan 1, 1917

By J. M. Harrison

FIELD PARTIES of the Geological Survey of Canada have, in recent years, mapped several areas east and northeast of Flin Flon (9, 10, 12, 13, 14, 15, 118) (1). In all these areas the mineral deposits show a close geographical relation to faults although the immediate control of most of the known ore deposits appears to be folded structures in the rocks (8, 11, 18, 19). Air photographs and published geological maps were studied in order to ascertain whether or not the mineral deposits in the Flin Flon-Snow Lake mineral belt as a whole show any spatial relationship to faults. It was found that most of them do show a distinct geographical association with faults, or with topographic features that may be faults. It is further apparent on air photographs that a major lineament, for composite of lineaments, follows approximately the contact between gneisses and schists of the Kisseynew complex on the north, and Amisk volcanic rocks on the south. However, this Kisseynew lineament is not continuous and, especially in the eastern half of the district, it is exceedingly irregular in plan. Parts of this lineament have been mapped as faults (9, 10, 12, 14), other parts have been shown as stratigraphic contacts (1, 2, 21, 27), and still other parts have not been studied except by reconnaissance methods. It is suggested that the Kisseynew lineament may be due to a deformed fault that extends easterly from a point about 25 miles west-northwest of Flin Flon to a point at least 10 miles northeast of Wekusko lake and that the mineral deposits.

Jan 1, 1951

By John P. Harmon

A group of organic chemicals, known as wetting agents, has been developed, primarily for use in the textile industry. These chemicals have the property of reducing the surface tension of water when mixed with it in very dilute solutions. The advantage of lowered surface tension is recognized in dust-control work, and several wetting agents, have been tried by dust-control engineers with varying degrees of success. It is well-known that certain solids, coal for instance, are extremely hard to wet with plain water because of the high surface tension of water and the water-repellent action of coal. If the surface tension of the water is reduced, it can be demonstrated that the coal can be wetted easily. This is accomplished practical and at law cost by dissolving a very small percentage of wetting agent in the water that is to be used for wetting purposes. (Care should be exercised in using a wetting agent to be sure that it will not interfere with a subsequent process.) For some time, the comparative efficiency of various wetting agents has been the subject of considerable work by dust-control men at coal mines, as well as by members of the Bureau of Mines 3/, 4/, 5/, 6/. In this connection, a number of samples of air-borne dust have been collected in the mines. With the exception of dust-control measures conditions of dust generation and dissemination were maintained as, nearly uniform as possible. Samples were collected when water alone was sprayed on the cutter bar of a mining machine; various wetting agents were then successively added to the water and more samples of air-borne dust were-collected.

Jan 1, 1946

By J. P. Rider

Operating practices and resulting production from longwall faces are continually improving. Consequently, longwall operators are continually seeking to improve the dust control capabilities on longwalls. The National Institute for Occupational Safety and Health (NIOSH) has been conducting dust surveys at longwalls throughout the country in an effort to document the types of controls that are being used and to quantify the relative effectiveness of these controls. To date, surveys have been completed at longwalls in Alabama, Colorado, Pennsylvania, Utah, and West Virginia. In addition NIOSH has been reviewing longwall dust parameters provided by mine operators to MSHA to assess the status of dust control technology being used throughout the industry. Results from the underground dust surveys and information obtained from MSHA will be summarized in this paper to provide an update on longwall dust control technology and practices.

By Yuri Bychkov

The Electron Beam Melting is the most efficient technology for metals and alloys refining. For ,secondary metals processing the Electron Beam Skull Melting (EBSM) with the electromagnetic stirnng (EMS) of melt in the crucible was shown to be the most appropriate. The copper produced by EBSM with EMS possesses higher density and electric conductivity in comparison with other refining methods. The details for high power electrical machines were cast of the copper waste refined by EBSM technology.

Jan 1, 1995

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

By M. J. Laurila

Elemental analysis of slurry streams using X-ray fluorescence (XRF) has long been employed. However, detector technology has limited the application of XRF devices. Using detector technology employed on NASA's Mars Pathfinder to analyze soil samples, Process Control, Inc. has developed an on-line analyzer to mount on a sampling system. The prototype XRF elemental analyzer was installed at Detroit Edison's Monroe Power Plant in January, 1998 and has been employed to monitor feedstock quality. A slurry system has been developed for flotation control. This paper describes the testing of the analyzer using the new, draft ISO standard for evaluating the performance of on-line analyzers (ISO/DIS 15239).

Jan 1, 1999

By João F. C. L. Costa, Vanessa C. Koppe, Clayton V. Deutsch, Marcel A. A. Bassani, Pedro H. A. Campos

Blending inevitably occurs to some degree during mining and mineral processing operations. Traditional mine scheduling assumes that all variables average linearly, which allows the calculation of the blended material properties as a linear weighted average. However, metallurgical properties such as metal recovery and Bond Work Index (BWI) are known to average nonlinearly. The nonlinear properties of the blended material can be calculated using nonlinear blending models. A simulated annealing algorithm is developed and applied to a short‐term mining face optimization problem to maximize the total metal recovered considering nonlinear blending. Compared to a standard schedule plan, the optimized one shows relevant improvements in synergistic and antagonistic blending behaviors.

Jun 25, 2023

By Eberhard Stolarski, Michael Tacke

When the oxidized surface gold deposits are mined out, the underlying refractory gold ores become the challenge of treat­ment systems. The size and value ofrefractory gold ore reserves are a function of recovery efficiency and operating cost. The start-up of LURGI's gold roasters at NEWMONT's Carlin site has established whole ore gold roasters as a key to high gold recoveries. The ores from several deposits of the Carlin trend are roast­ed utilizing LURGI / NEWMONT technology, which has achieved gold recoveries approaching 95%. This is in dramatic contrast to the traditional perception that roasting is limited to gold recoveries in the mid 80's. Extensive investigation in pilot scale is required to achieve stable high gold recoveries for most variables in the ore body. The key question for all pilot tests is the classic question of (ROM) run of mine ore roasting or concentrate roasting. All variables are dominated by the leaching/ recovery char­acteristics of the natural ores. The degree ofrecovery improve­ment by roasting / calcining establishes the frame of the eco­nomical conditions. The full range of flexibility is required for the design of the plant to allow for ore variations in heat values, combustible con­tents, agglomeration behavior and off-gas composition. The variables in the ore body influence, therefore, the price of the plant proportionally to its flexibility. Concentrates are usually fairly stable in composition, com­bustion behavior, heat values and particle size since they are a product of the very selective flotation process. Flotation is not the successful process step when the tailings remain high in refractory gold contents.

Jan 1, 1996

By R. C. Good

Slag control for any kind of steel, rimming, straight carbon or alloy, should start with the charge and be developed well in advance of the tap because its composition, viscosity and temperature will unquestionably govern the physical and chemical properties of the steel when tapped. In the majority of plants producing alloy steels, primary consideration is given to the chemical specifications; physical characteristics usually occupy secondary place in the melter's mind. Recently, however, buyers have indicated limits of machinability, hardenability, grain size and, of course, always wanted steel free from foreign nonmetallic inclusions. It is these latter specifications that require the attention of the operator to the slag and its control. The slag must act as a vehicle for oxidized elements originating from the metallic portion of the charge; it should hold the oxides of phosphorus, silicon, manganese, iron and chromium that come into contact with it either before or after the refining and finishing stage of the heat. It must be used as a transferring medium of oxygen from the atmosphere or oxide additions to the metal and should permit a free escape of gas generated within the charge. Finally, the slag is the principal controlling factor in regulating the rate of oxidation which in turn eventually determines the quality of the steel as measured for the various characteristics mentioned above. With pig iron of uniform composition, the iron oxide in the slag increases as the limestone is increased but with the same addition of stone in every heat, the iron oxide decreases as the silicon is increased in the charge, and vice versa.

Jan 1, 1935

By C. Augustus Carlow

THE subject which has been allotted to me is so vast and far-reaching that it is impossible to deal adequately with it in the time available. A complete survey would occupy the spare time of any one man for many years, whereas the time available to me is measured in weeks In the circumstances, I have been fortunate in securing the aid of several willing collaborators, and shall endeavor to re present such information as presently exists in published form, examine the situation critically in the light of present-day conditions, and arrive at certain conclusions' which I shall venture to put forward for your consideration No one who has lived through the past 25 or 30 years, and who has witnessed the amazing achievements of recent scientific research, would venture to deny the possibility that new sources of energy-may yet become available, or to prophesy to what extent these may be harnessed to the service of mankind So far as we can see, however, coal, as a source not only of power and heat but also of that wonderful range of derivatives that form the raw materials of so many industrial processes, must continue to play a vital role in our economic life It is the chief mineral fuel, exceeding all other mineral resources in value, production and demand In value coal overshadows the industrial metals, while of the sources of energy-coal, oil, gas and water power-the first named is the most important Thus, for example, in the United States, coal as a fuel (that is, as a source of heat and power) is still predominant, the figures of percentage of

Jan 1, 1947

By R. C. Good

Slag control for any kind of steel, rimming, straight carbon or alloy, should start with the charge and be developed well in advance of the tap because its composition, viscosity and temperature will unquestionably govern the physical and chemical properties of the steel when tapped. In the majority of plants producing alloy steels, primary consideration is given to the chemical specifications; physical characteristics usually occupy secondary place in the melter's mind. Recently, however, buyers have indicated limits of machinability, hardenability, grain size and, of course, always wanted steel free from foreign nonmetallic inclusions. It is these latter specifications that require the attention of the operator to the slag and its control. The slag must act as a vehicle for oxidized elements originating from the metallic portion of the charge; it should hold the oxides of phosphorus, silicon, manganese, iron and chromium that come into contact with it either before or after the refining and finishing stage of the heat. It must be used as a transferring medium of oxygen from the atmosphere or oxide additions to the metal and should permit a free escape of gas generated within the charge. Finally, the slag is the principal controlling factor in regulating the rate of oxidation which in turn eventually determines the quality of the steel as measured for the various characteristics mentioned above. With pig iron of uniform composition, the iron oxide in the slag increases as the limestone is increased but with the same addition of stone in every heat, the iron oxide decreases as the silicon is increased in the charge, and vice versa.

Jan 1, 1935

By Zheng Wei, Jian Cheni, Zhenliang Weng, Wei Liang, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"By testing the dielectric constant and the dielectric loss factor of concentrated Dahongshan, mill scale, anthracite and light-burned dolomite in different frequency and temperature, and by studying the temperature-rising characteristics of the materials in the microwave field of 2.45GHz in frequency, the research in the paper shows that to reach at 1250°C under the same condition -2KW the microwave power and 30g the mass --the time concentrated Dahongshan takes is 330s, whereas the millscale is 855s and the anthracite is 820s. About the last one, the higher the temperature is, the stronger the absorptivity is. After the temperature has rose to 400°C, the anthracite's absorptivity increases dramatically. The result of the research would serve as the foundation of the further study on making direct reduced iron by microwave heating.1. IntroductionUnder the microwave fields, materials' dissipation of dielectric bodies would generate thermal effect. Therefore, the dielectric constant and the dielectric loss factor are closely related to materials' ability of absorbing microwave energy-the larger the dielectric constant and the dielectric loss factor are, the stronger the material's ability of absorbing microwave energy is, and the better the thermal effect would be[1-2]. In order to research how to make reduced iron from iron ore fines by microwave heating deeply and systematically, the test of raw materials' dielectric constants and dielectric loss factors are of the essence. What's more, because a mineral' conductivity is influenced by its components and crystal structure[3], it is necessary to study different materials' different temperature-rising characteristics; hence such studies would provide theoretical foundation of further research."

Jan 1, 2012

By Ashish Kumar

Comminution is an essential mineral processing operation to liberate the minerals from the ore. This however, is an energy intensive step in mineral processing industries. This work highlights the possibility of saving in grinding energy for ore comminution reducing work index of the ore by effective utilization of microwave energy. This reduced work index results in increased throughput of the grinding circuit in mineral beneficiation plant in order not to shift the product size. The fundamental principle behind this application remains the ability of microwave to heat individual phases within the ore matrix. The constituents of the ore typically having different thermal and mechanical properties develop stress of sufficient magnitude to create intergranular and transgranular fractures during heating and subsequent quenching of the ore. The experiments conducted with the ore samples of Zawar Mines and Rampura Agucha Mine of Hindustan Zinc Limited, India (A member of Vedanta Resources Plc) reflect a substantial up-shift in cumulative weight percentage passing in finer sieve fractions under quenched conditions. Further, the experiments carried out on Rampura Agucha ore reveal 20-30% reduction in work index, which result in decreased milling time or saving in grinding energy. The simulation studies estimates a 2-4% increase in plant throughput. Moreover, preliminary flotation studies indicated a significant increment in total metal recovery and concentrate grade for the desired grade and recovery values respectively. This paper is a technical note on the laboratory investigations carried out at Central Research & Development Laboratory of Hindustan Zinc Limited. Results have been encouraging to progress the work further. It is also proposed to carry out modeling work for simulation so as to predict the changes in minerals.

Jan 1, 2006

Discussion of the paper of HENRY M. HONE and ARTHUR G. LEVY, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 587 to 600. J. E. STEAD, Middlesbrough, England (communication to the Secretary*).-As I have not personally studied the question of quenched and distorted manganese steels I cannot give any information of my own on the subject. The question as to whether certain indications in strained manganese steel are "slip bands" or "twins" might be settled, I think, by heat tinting-a method I have applied with success to certain meteorites and other alpha irons in which there were undoubted twins. After polishing and very slightly etching with picric acid in alcohol, and then "heat tinting," the colors assumed by the twinned strata and the adjoining metal are different. The reason of this, as I have proved repeatedly, is that different faces of the iron crystals are differently attacked by oxidizing and other reagents, and consequently some of the faces take temper oxidation tints more rapidly than others. This simple method enables one to determine with certainty whether the "twins" are actually, twins and differently oriented from the bed in which they are found. After correspondence with Dr. Howe, I think we both agree that Neumann lines should not be called "lines" but "bands" or "strata," preferably the latter term, as I have found that they are more or less continuous throughout the crystals, and it would be just as improper to call the edges of cementite plate by the term "lines" as to call stratified twins by the same term.

Jan 5, 1915

Committee on Reduction and Refining of Copper............ 3 A.I.M.E. Officers and Directors.................... 4 Preface. By C. R. Kuzell....................... 7 Career and Achievements of James Douglas. By Arthur L. Walker. . 9 PAPERS Smelting 1. Reverberatory Smelting Practice History of Reverberatory Smelting in Montana, 1879-1933. By Frederick Laist..............................23 Reverberatory Smelting of Raw Concentrates at the International Smelter, Miami, Arizona. By P. D. I. Honeyman (With Discussion)...... 88 Development of Gun-feed Reverberatory Furnaces at Garfield Plant of American Smelting and Refining Company. By R. A. Wagstaff (With Discussion)........................99 An Experimental Combination of Shaft Roasting and Reverberatory Smelting. By Frederick Laist and J. P. Cooper (With Discussion).... 104 Forms of Copper Found in Reverberatory Slags. By Royal B. Jackman and Carle R. Hayward (With Discussion).............111 2. Converting Practice Development of Copper Converting at Butte and Anaconda. By William Kelly and Frederick Laist...................122 Developments in Converting Lead and Copper Matte at Tooele. By B. L. Sackett.............................132 Messina Stationary Basic Copper Converter. By R. G. Knickerbocker (With Discussion)........................140 Smelting Copper Concentrates in a Converter. By George E. Beavers. 149 Sulfuric Acid from Converter Gases. By George E. Beavers......151 Development of Monolithic Tamped Periclase Converter Linings at United Verde Copper Company Smelter. By F. H. Parsons (With Discussion) . 153 3. Descriptions of Plants The Noranda Smelter. By W. B. Boggs and J. N. Anderson......165 Smelting Operations at Roan Antelope Copper Mines, Limited. By Charles R. Wraith.......................202 4. Waste-heat Boiler Practice Copper-refinery Waste-heat Boilers at Great Falls Reduction Department, Anaconda Copper Mining Company. By E. S. Bardwell......225

Jan 1, 1934

By Esa J. Peuraniemi

Copper smelting to form blister in one single step has been possible for a long time even from low grade concentrates. In spite of obvious benefits, it has been economically viable only with few special raw materials having high enough Cu/Fe and Cu/S ratio. Outokumpu Blister Flash Smelting is currently applied at three operations, and three others will be commissioned in the near future. With typical chalcopyrite concentrates two main obstacles have prevented wider adaptation of direct blister processing: slag formation and heat generation. Oxygen potential in the reaction shaft must be high in order to produce blister with targeted sulfur content below 1%. When large amount of iron is oxidized, as well as sulfur, copper is inevitably also oxidized into slag. High copper amount in substantial tonnages of slag lead on to costly down stream recovery operations to obtain discardable slag. Almost complete oxidation of sulfur and iron releases a high amount of heat which traditionally has been solved by lowering oxygen enrichment of the blast leading on to oversized off-gas line and acid plant. One challenge in direct blister smelting relates to the attack of aggressive high-copper containing slag against furnace refractory lining. In continuously operated Outokumpu Direct Blister Flash Smelting this is taken care of by preventing vigorous melt movement in the settler. Stable bath conditions and stationary slag against refractory lining enable the formation of a protective autogenous layer between aggressive slag and vulnerable refractory. These direct blister smelting challenges are addressed from equipment and process development point of view. New solutions to overcome the obstacles are presented and discussed.

Jan 1, 2006

By A. L. Titchener, M. B. Bever

FROM their investigation of the martensitic transformation in Cu-Zn alloys, Greninger and Mooradian' concluded that there was no critical temperature at which martensite formation began in this system. Recent unpublished work by Gen-evray With two compositions of brass revealed the existence of a critical temperature, which is a function of composition and stress. In the work reported here the temperature range of the martensitic reaction was studied as a function of composition in high purity Cu-Zn alloys. The specimens were about 4 in. long with a diameter of 1/16 in.; their compositions are given in Table I. They were heated under vacuum for 5 min at 5" to 10°C below the temperature of incipient melting, and quenched into brine at about — 10°C. Specimens of alloys C, D, E and F were obtained with little or no precipitated a phase. Many attempts yielded only three usable specimens of alloy B, and even these contained appreciable amounts of a. All efforts failed to preserve metastable p in alloy A (containing 38.02 pct Zn and 0.002 pct each of Pb and Fe). The transformation was studied by measuring the electrical resistance during continuous cooling and heating of each specimen at similar rates. The cooling media were alcohol with dry ice from room temperature to — 78°C and a bath of petroleum ether and methyl cyclohexane (75:25), cooled by liquid nitrogen, from —78" to about —150°C. Readings were also taken at —195 °C in liquid nitrogen. Fig. 1 illustrates a typical experiment. The relative resistance is obtained by assuming the known

Jan 1, 1955