Search Documents

By P. S. Martin, B. J. Guarnera

As an energy source, lignite is short on selling points-it contains large amounts of moisture and often large amounts of ash, resulting in low heat content. The moisture produces rapid oxidation upon exposure and self-ignition commonly occurs within two to three weeks, resulting in major transportation and storage problems. Nevertheless, as interest in alternate fuel sources increases, lignite deposits in the Coastal Plain of the US are attracting more and more attention. Two lignite mines are operating in Texas and additional developments are planned in that state, Arkansas, and Louisiana. At present, Texas lignite is burned only at mine-mouth generating facilities, but more exotic uses such as gasification are projected in the future.

Jan 4, 1979

By John G. Reid

Subsequent to extensive laboratory testing, a pilot plant was constructed to further evaluate the process for high temperature copper cementation on iron in continuous operation. The plant was designed to produce 1 to 10 tons of copper a day depending on the copper concentration of the pregnant solution. The energy required to operate the plant was very low as virtually all the solution heating requirements were supplied by the exothermic cementation reaction. The results demonstrated that this, process has potential for commercial application with respect to operating considerations, and yields a copper product in excess of 95% copper at high reaction rates, low iron consumption, and at least 98% copper recovery from solution.

Jan 1, 1976

By P. K. Koh, L. S. Birks, J. M. Siomkajlo

Direct identification in situ of x and a phase precipitates in stainless steel is possible with the electron probe microanalyzer. Although particles in the 1 p size range are too small to yield absolute percent composition, the relative % Crfi Mo ratio can be used to distinguish the two phases with better than 95 pct confidence. Wet chemical analysis of extracted residues gives Cr/Mo ratios in good agreement with electron probe results extrapolated to the 4 to 5 p size range. WHEN stainless steels are subjected to extended heating in the temperature region around 1600°F, precipitation of the brittle 0 or x phases may occur and impair the properties of the material. Identi-

Jan 1, 1961

By M.E. Crump

Gallium occurs at above background levels in most samples collected from 11 of the major geothermal areas in the Taupo Volcanic Zone. Concentrations of Ga in the 48 samples ranged from 8 to 144 mg kg-' and varies widely from place to place within each geothermal area. Gallium is contained within the alumino-silicate structure of clay in the mud, having substituted mainly for Al. Suggested deposition mechanisms for Ga also involve co-precipitation with Sb, As, and SiO. colloids. Digestion trials, carried out to determine extraction conditions for possible commercial exploitation, showed that heating the mud to 500 -600¦C for 1 hour followed by acid/alkali treatment gave complete recoveries.

Jan 1, 1995

By Katsutoshi Komeya

Aluminum nitride(A1N) is a theoretically high thermal conductive ceramic, but is a poor sinterable one because of its covalent bond structure. The densification of A1N had to be done first. It was found in 1968 that rare earth compounds as yttria were an excellent sintering aids. Recently more improvement of conductivity was attained by following effects of yttria: (1) trapping of oxygen in A1N sources to form yttrium aluminates, (2)elimination of the aluminates by heating in carbo-reductive atmosphere. Consequently very high thermal conductivity of up to 270W/mK has been developed. Thus A1N applications for substrates and packages have been opened.

Jan 1, 1992

By R Balusu

This paper provides an overview of computational fluid dynamics (CFD) modelling capability developed by CSIRO with the aim of improving the knowledge of flow migration dynamics within longwall goaf areas. The CFD models can be used to study the ingress of oxygen into the goaf in different ventilation scenarios and goaf drainage arrangements. This approach not only helps the design of effective gas control strategies but also the management of spontaneous combustion risk in the goaf. Innovative goaf inertisation strategies have been developed and implemented during longwall sealing operations. Work is continuing to develop general guidelines of proactive goaf inertisation strategies to suppress the development of spontaneous heating behind active longwall faces.

Jan 1, 2005

By Douglas M. Smith

Silver-gold ratios were studied at the Tayoltita epithermal vein deposit using channel sample, channel sample line, stope, ore body, and vein sample populations. The ratios are highly variable among individual channel samples (25:1 to greater than 500: 1) with both high and low values randomly distributed within ore bodies and veins. Whole vein ratios for the 14 most important ore producing structures range from 44: 1 to 105:1, and show zonal distribution relative to two small granitic stocks, low values closest to the intrusives. The zoned nature of the deposit suggests that the stocks, apophyses of an underlying batholith of late Eocene age, were the heat engines which powered the hydrothermal system responsible for ore deposition.

Jan 1, 1980

By Robinson BW, Walker RK

Using a new highly stable automated electron microprobe analyser, detection limits for gold in arsenopyrite have been improved. Using the AuLA emission tine at 40kV and 500nA, a limit of approximately 10gpt is attained in 10- lSmins. Some unusual features of the background need to be taken into account. Several ores containing different levels of gold in arsenopyrite have been examined, and it has been shown that gold is not evenly distributed between grains (some may contain more than 1%, invisible optically), and that the grains containing gold are often zoned. Gold may be released from the arsenopy rite by weathering or by heating in an inert or slightly oxidising atmosphere.

Jan 1, 1989

By H. Soto, I. Iwasaki

Primary amines are strong collectors of apatite and they can selectively float sedimentary phosphates from calcareous ores. However, secondary and tertiary amines and trimethyl ammonium salts are ineffective. Kerosene reduces the collector requirements became hydrocarbon is co-adsorbed along with the amine on the mineral surface. The heats of reaction of aminium ions with such anions as phosphate, carbonate, and sulfate were measured in a microcalorimeter. They are discmsed in terms of the solubility of the precipitates formed and their relationship with the adsorption mechanism of primary amines on phosphate minerab. Experimental evidence supports a view that primary amines are adsorbed through chemical interaction between the aminium and phosphate ions at the mineral surface.

Jan 1, 1986

By M. Abdel-latif, R. W. Bartlett, P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines was designed and operated. A nontransferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained above 1673 OK (1400°C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbonmonoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pres- sure and average reactor temperature. The interaction of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1995

By T. V. Jayaraman

Fe-Ga alloys, with compositions around 27.5 at % Ga, can be heat treated to obtain ? (ordered bcc), DO19 (ordered hexagonal), and L12 (ordered fcc) ordered structures. Our earlier work using polycrystalline samples had shown that magnetostriction is strongly influenced by ordering in this alloy. Here more detailed study of the correlation between ordering and magnetostriction using single crystals of Fe 27.5 at. % Ga alloys is reported. Single crystals of Fe 27.5 at % Ga were grown using Bridgman single crystal growth technique. X-ray and electron diffraction were used to study the ordering in this alloy. Magnetostriction measurements were carried out at no load conditions. Elastic constants were measured using Resonant Ultrasound Spectroscopy.

Jan 1, 2006

By Pinakin Chaubal

The campaign life of a modern blast furnace depends on hearth wear. Distributions of liquid iron flow and refractory temperatures have a significant influence on hearth wear. A 3-D comprehensive CFD model has been developed specifically for simulating the blast furnace hearth. It includes both the hot metal flow and conjugate heat transfer thorough the refractories. The model has been extensively validated using measurement data from actual blast furnaces. Good agreements between measured and calculated refractory temperature profiles haven been achieved. It has been used to analyze the velocity and temperature distributions and wear patterns at different furnaces and conditions. The results can be used to point out the directions for protecting the hearth.

Jan 1, 2006

Gallium occurs at above background levels in most samples collected from 11 of the major geothermal areas in the Taupo Volcanic Zone. Concentrations of Ga in the 48 samples ranged from 8 to 144 mg kg-1 and varies widely from place to place within each geothermal area. Gallium is contained within the alumino-silicate structure of clay in the mud, having substituted mainly for Al. Suggested deposition mechanisms for Ga also involve co-precipitation with Sb, As, and SiO2 colloids. Digestion trials, carried out to determine extraction conditions for possible commercial exploitation, showed that heating the mud to 500 - 600¦C for 1 hour followed by acid/alkali treatment gave complete recoveries.

Jan 1, 1995

By Ted C. Briggs

A removable-jacket distortion apparatus was constructed and used to measure distortion coefficients for two high-pressure vessels. The measured distortion coefficients were used to compute distortion coefficients for volumes VI and (V1+V2) of a 1,000-atmosphere Burnett compressibility apparatus for the temperature range 0° to 75° C. Young?s modulus for Armco 17-4 PH stainless steel, heat treated to condition H1150-M, was computed from experimentally determined distortion coefficients. A 10-to 14-percent correction to the values obtained for Young's modulus may be required because pressure vessel end effects were neglected. The distortion coefficients of the compressibility apparatus are believed to be accurate to about 1 percent.

Jan 1, 1970

By W. Rostoker, S. A. Spachner

FOLLOWING the discovery of the w transition phase in certain titanium-chromium alloys by Frost, Parris, Doig, and Schwartz, much interest has centered on the alloys in which this phase is found and its mode of precipitation. The w phase has been found in alloys of Ti-Cr, Ti-Fe, Ti-Mn, Ti-MO,2 and Ti-v.3 The temperature-time-transformation characteristics have, as yet, not been determined for most of these. In this study, such transformation characteristics have been investigated for two heat-treatable titanium alloys known to exhibit transition phase phenomena. The alloys chosen, Ti-8Cr and Ti-13M0, are representative of two classes of binary equilibrium systems. In the

Jan 1, 1959

The operators of the iron ore railroads in the Pilbara faced problems of excessive wear between rail and wheels as the tonnage hauled increased in the early 1970's. Joint research projects were begun between Hamersley Iron, Mt Newman Mining and the BHP Melbourne Research Laboratories to study these problems and recommend solutions. The particular problems of wheel rail interaction were solved by asymmetrical profile grinding of the rail and modifications to the machining of the wheels. Rail materials were improved through increasing yield strengths by alloying and by heat treatment. Wheel materials were improved by alloying. The economic benefits of these improvements have been demonstrated by much reduced re-rail requirements and other reduced maintenance costs.

Jan 1, 1986

By K. Tsuchihashi, A. Kishimoto, T. Uda, Y. Kado, S. Maruyama

We recently proposed a continuous production process for titanium metal with some experimental results. In the process, titanium tetrachloride is reduced by Mg in the presences of Bi to form a Bi-Ti alloy at 900ºC. At this temperature, the obtained alloy is liquid and allows for the continuous removal of product and heat from the reaction vessel. The obtained Bi-Ti alloy was vacuum-distilled at 1000ºC for 24 hr, and 98 at % (92 wt %) titanium, which was easily crashed to powder, was obtained. Bi solvent was selected because of the highest titanium solubility at 900ºC and the moderate vapor pressure among the candidate metals (Bi, Sn, Pb, Zn, and Sb).

Jan 1, 2014

By Y. G. Seredkin, A. A. Vasiliev, A. Y. Senchenko, A. V. Aksenov

"Autoclave oxidation, bacterial and chemical liberation, roasting, acid oxygen processes, atmospheric oxidation prior to cyanidation are applied to process refractory sulphide concentrates. It is obvious that the processes with the maximum effect regarding gold recovery are those in which complete destruction of sulphides takes place and gold becomes accessible for further cyanidation through liberation from sulphide “capsula”. But the significant recovery increase is often accompanied by a process complexity, high expenses for equipment purchase and maintenance. It makes material processing costinefficient. Process optimization has led to progress in ultrafine grinding, bacterial and autoclave oxidation processes. In our opinion sulphide atmospheric oxidation processes are the most interesting as oxidation there runs without high temperature (up to 100°?) and excess pressure (open units), and with acid environment close to neutral. The process of sulphide concentrates treatment named “Albion” (Albion Process™) represents a combination of ultrafine grinding and oxygen oxidation without pressure and external heating. The process has a number of advantages: sodium cyanide consumption decrease during gold leaching and high ecological compatibility. TOMS institute in collaboration with Glencore Technology Pty ltd (Australia) tested Albion technology aiming at liberation of finely disseminated gold from flotation concentrate produced from refractory ore of one Russian deposit. The testing has shown that Albion technology makes it possible to process refractory products with quite small capital investments. It enables involving medium and small refractory gold deposits into processing.INTRODUCTIONThe considerable part of the world Au-bearing reserves is present by refractory ores with finely disseminated gold. Gold in such ores is often associated with sulphide minerals and locked in so called “sulphide capsula” since it is closed inside dense sulphide grains and inaccessible to recovery by cyanidation. To treat refractory sulphide concentrates containing gold a number of processes were developed and they can be divided into three groups (Figure 1)."

Jan 1, 2016

By D. Duffy, V. Papangelakis

"MgCl2 brines present a number of potential advantages for the processing of saprolite ores for nickel production. With a chloride system it is economically requisite to recover hydrochloric acid, which can be performed in a more energy efficient manner by precipitation and subsequent decomposition, as compared with conventional pyrohydrolysis. In addition, concentrated MgCl2 solutions enhance the activity of acid used, allow atmospheric leaching at elevated temperature and inhibit magnesium dissolution, which reduces acid consumption and increases metal selectivity. Leaching and iron control experiments have been conducted in concentrated MgCl2 brines, up to 4.5 m, to determine the most amenable process conditions. INTRODUCTIONChloride metallurgy has received an increasing amount of attention in recent years, especially with respect to the treatment of nickel laterites. Although the limonitic fraction can sometimes be economically treated by High Pressure Acid Leaching (HPAL), acid-consumption problems are encountered with the higher magnesium content of the saprolite fraction. As magnesium does not hydrolyze under HPAL conditions, as iron and aluminum do, any sulphuric acid used to leach magnesium is subsequently neutralized and wasted. In addition, this magnesium must later be disposed of in some fashion, further complicating the process. The most common method used to process saprolite is the Rotary Kiln-Electric Furnace (RKEF). This uses a kiln to dry and preferentially reduce nickel, before sending the calcine to an electric furnace. Although nickel recoveries are high, and the problems of acid consumption are avoided, the capital and energy costs associated with this process are high (de Bakker, 2011).The problems outlined above have led to the investigation of an atmospheric chloride process for the treatment of saprolite ores. The use of a chloride system presents a number of advantages, but also a few limitations. Metal chlorides tend to be very soluble, with a few notable exceptions (silver, mercury and lead), allowing for smaller processing equipment through more concentrated solutions. This solubility also serves to reduce the potential for scale formation. In addition, a hydrochloric acid leach is more aggressive than a comparable sulphuric acid system, and the activity of the hydrogen ion can be augmented by further chloride addition (Peek, 2011). This activity augmentation in concentrated chloride systems, first reported by Jansz, has repeatedly been referenced as a motivating factor behind chloride hydrometallurgy (Jansz, 1983; Harris and Magee, 2003; Harris et al., 2004; Demopoulos et al., 2008; McDonald and Whittington, 2008; Demopoulos, 2011; Peek, 2011; Verhulst and Lakshmanan, 2011). This activity increase allows a similar amount of acid to perform more in a concentrated solution than in a dilute solution, decreasing overall acid requirements. As such, much focus has been placed on leaching in concentrated chloride systems, or brines, using calcium, magnesium or sodium as the cation (McDonald and Whittington, 2008)."

Jan 1, 2012

By José Murilo Mourão

A pelotização de minério de ferro hematítico demanda grande quantidade de calor para a produção de pelotas de boa qualidade. Avalia-se, neste trabalho, a quantidade teórica de calor, necessária para a queima de três tipos característicos de pelotas, e destacam-se pontos importantes do processamento de queima nos fornos de pelotização, no sentido de otimizar o consumo de calor..

Oct 30, 2017