Search Documents

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

By P. M. May, J. S. Solis, G. T. Hefter

Chemical speciation plays a critical role in many areas of gold processing. These include the formation of HCN in plant liquors, interference by copper in the extraction efficiency of gold, the recovery of adsorbed gold, and the behaviour of plant effluents in the environment. Thermodynamic modelling provides a cost-efficient method of rationalizing and even predicting of chemical behaviour. Unfortunately, because thermodynamic data for cyanide complexes are of poor quality and few are known under hydrometallurgical conditions. Such models are currently of limited use. This paper describes recent work on the thermodynamics of cyanide complexes of a range of metal ions. Data will be presented on the stabilities and enthal­pies (heats) and entropies of formation of a variety of metal ion species determined by potentiometry and calorimetry. Particular emphasis will be placed on the Cu(I)/CN- system.

Jan 1, 1995

Few people in the industry today are competent to comment on the O.G. system for vessel covers, but with papers as well prepared as Mr. Bradley's we will soon be well informed. I would like to direct these comments to Mr. Klaes of Ford Motor Company. Mr. Klaes' description of their steaming hood agrees with our experience at Weirton. We have been able to stay within design limits and, as a result, have had few problems with our auxiliary equipment. Our main problem, as with Ford, has been thinning of our vessel cover tubes. At Weirton, controlled circulation, high pressure boilers are in use as heat recovery units above the BOP vessels. The boilers are provided with "off cycle' oil firing equipment. A Venturi type wet gas scrubber follows the boiler to complete the vessel draft system.

Jan 1, 1972

By D. M. Bastidas

The reduction of copper sulfide and copper oxides originated during artificial tarnishing of copper was studied using potentiodynamic potential/current density experiments. Six copper surface treatments were considered: mechanical polishing; indoor exposure for 7 days; chemical etching in 1.6 M nitric acid; chemical etching and heating at 160°C; and chemical etching and dipping in a 9x10-4 M or 0.9 M potassium sulfide (1(25) solution at 70°C. Cuprite (Cu20) and chalcocite (Cu2S) were the main compounds formed. A linear relationship with the square root of the scan rate (v) was obtained by plotting the potentiodynamic potential/current density for the tarnish dissolution processes. A relationship between potential and current density cathodic peaks was not obtained, according to Müller's model, showing a proportionality factor with the dimensions of a resistance.

Jan 1, 2007

By P D. Kasbanis, Lyall Workman

The energy output of an explosive is typically calculated using an equation of state and computer applications. Results are reported as weight and bulk strength, either in absolute terms or relative to ANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of "available energy" associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated.

Jan 1, 1996

By J. le Grange, M. Tullmin, A. Strauss, F. P. A. Robinson, C. A. O. Henning

An experimental feritic stainless steel with a chromium content of 40 per cent was welded by laser and electron beam (EB) welding processes. These techniques were found to be particularly suited to the welding of this alloy in that the impact toughness of the weld metal and heat-affected zone (HAZ) of the laser welds compared favourably with those of the parent aloy. When the EB process was used, the impact toughness of the weld metal was over 180 J/cm2. Grain growth in the HAZ was minimal for welding with these two processes. Corosion tests, conducted in a solution consisting of 20 per cent sulphuric acid and 100 p.p.m. of potassium thiocyanate, and In a highly corrosive industrial solution, indicated that the laser and EB welds were free of sensitization effects, thus confirming the metalographic results.

Jan 1, 1989

By R. M. Morris, G. A. Matthesius, M. J. Desai

Slow pyrolysis experiments were caried out on samples of coal from north em Natal having a volatile mater content ranging between 10 and 25 per cent by mass and a constant particle-size distribution. The tests were conducted at atmospheric pressure in a helium atmosphere, and ata heating rate of 10 KImin and a final temperature of 1220 K. The pyrolysis products were taken as coke and volatile mater (tar and eight other species), and tMir respective yields were measured. The experimental results were used in the modification of an existing mathematical model and in the derivation of new corelations for some of the parameters of the model, so that the volatile products of a coal can be predicted from ultimate and proximate analyses of the coal. The pyrolysis tests showed good agreement between the model predictions and the experimental results.

Jan 1, 1987

By D. Harris, G. Ye, G. Oprea, J. Rigby, T. Troczynski

Sintering and ceramic bonding in refractory castables take place mainly in the binding system during the first heat-up and in service. Consequently the strength and the corrosion resistance of the hot face layer depend on the sintering ability of the complex mix of ceramic powders constituting the binding system. As a result, the use of nano- sized reactive powders in the binding system mixes would activate the sintering and enhance the ceramic matrix formation at temperatures below 1300°C. Our work presents the experimental data on sintering behavior of binding systems containing magnesium aluminate and alumina nano-powders in the temperature range of 800-1450°C. The results indicated that a ceramic matrix, similar to high temperature fired bricks, could be generated after firing at the relatively low temperatures available in the non-ferrous smelting furnaces.

Jan 1, 2004

By M Hino, Y Sasaki

Sustainable handling of municipal waste and sewage sludge has an important goal to recycle resources without supply of harmful substances to humans or the environment. The gasification mechanism of phosphorus from municipal waste and sewage sludge during the incineration process has been investigated to develop a phosphorus recovery system. Quadrupole mass spectrometer coupled to an electric furnace is applied to study the vaporisation behaviour of phosphorous gas phases from municipal solid waste (MSW) incinerator ash of sludge during solid-state reduction by carbon. Measurements are carried out in vacuum conditions of 2 x 10-6 Torrs and furnace temperature range 573 - 1773 K, at a heating rate of 7.22 K/minute. It has been found that most of the phosphorus is vaporised as PO2, P2 and P4, in agreement with thermodynamic estimation despite a shift in the temperature regimes.

Jan 1, 2006

H. D. HIBBARD, Plainfield, N. J. (written discussion *).-While this valuable and timely paper may not go to the root of the matter, it deals with many of the elements and factors involved. It might be taken as the engineer's solution of the case, starting with the assumption that steel is steel, while the tendency for a rail to have transverse fissures may, and probably does, depend, in part at least, on conditions met before it reaches the track. Admitting with the author that "brittleness of fracture in all grades of steel is characteristic of fatigue tests" we may yet look farther back to find out, if possible, why some rails and some steels are more prone to have transverse fissures than others, for it has been found that rails from certain heats of steel developed these fissures under a service which

Jan 3, 1918

By Edward A. Loria

A SERIES of papers on the study of austenite grain A size in cast steels has been published recently.'" These studies show that in the as-cast state, the austenite grains are quite large, for they form as the steel freezes at a very high temperature, but a simple reheating above the critical range produces a new set of austenite grains which, in many instances, is finer than ASTM grain sire No. 8. Furthermore, there is no apparent relationship between as-cast austenite grain size and subsequent grain size produced by heat treatment. The as-cast austenite grain size can be determined easily in plain carbon and low alloy steels which produce a continuous grain boundary f errite envelope in the as-cast structure. In the case of cast steels whose alloy content produces greater hardenability and suppresses the proeutectoid ferrite transforma-

Jan 1, 1952

By Thomas M. Drown

AT the meeting of the Institute in New York,, in February, 1880,* I described a process of determining sulphur in metallic sulphides, with especial reference to the determination of pyrites in coal. The process, as then described, is as follows : A solution of sodium hydrate, of 1.25 specific gravity, is saturated with bromine. If an excess of bromine is used it must be neutralized by the addition of a :little more sodium hydrate. The pulverized mineral or coal is moistened with 25 c.c. of this solution and heated, then hydrochloric acid is added cautiously to just acid reaction. This operation is repeated with another 25 c.c. of the alkaline solution, and again rendered acid. The mixture should be kept hot. The contents of the beaker or dish are then * Transactions, American Institute of Mining Engineers, vol. viii, p. 569.

Jan 1, 1881

By A. J. W. Headlee

RECENT interest in germanium centers around its use as a semi-conductor of electricity in electronic devices. It is generally believed that germanium transistors, diodes, triodes, photocells, and rectifiers will largely replace the present-day vacuum tubes. The germanium electronic devices are much smaller, lighter, and more resistant to shock, and they require only a small fraction of current required for conventional devices. Hence only a small amount of heat is given off by the equipment. This development will require many times the quantity of germanium now being produced, which in 1948 was approximately 1000 lb1 and was obtained almost entirely from zinc ores in Missouri, Kansas, and Oklahoma. No one knows with certainty what the demand will be for germanium by 1956. It may be 40,000 lb.1 Known concentrations in zinc ores are not sufficient to

Jan 10, 1953

By Eugene P. Pfleider

RECENT interest in germanium centers around its use as a semi-conductor of electricity in electronic devices. It is generally believed that germanium transistors, diodes, triodes, photocells, and rectifiers will largely replace the present-day vacuum tubes. The germanium electronic devices are much smaller, lighter, and more resistant to shock, and they require only a small fraction of current required for conventional devices. Hence only a small amount of heat is given off by the equipment. This development will require many times the quantity of germanium now being produced, which in 1948 was approximately 1000 lb' and was obtained almost entirely from zinc ores in Missouri, Kansas, and Oklahoma. No one knows with certainty what the demand will be for ger-manium by 1956. It may be 40,000 lb.1 Known concentrations in zinc ores are not sufficient to

Jan 1, 1954

By Kewal K. Kohli, Richard E. Thill, Syd S. Peng

The results of unpublished investigations into surface subsidence from coal mining in the Northern Appalachian Coalfield are summarized. These investigations were carried out by various coal companies and the State of Pennsylvania in the sixties and seventies. Subsidence data were collected and analyzed from 10 room-and-pillar panels in 5 mines in the Pittsburgh coal seam. Results show that angle of draw ranges from 26° to 33° and subsidence factor from 0.42 to 0.72; surface heating generally occurs beyond the edges of the panel, the amount and extent of which vary; waviness occurs in the subsidence profile if a substantial number of pillar stumps are left in irregular patterns; interpanel effect is significant; time-dependent subsidence exists, but varies for different panels; and surface slope does not seem to affect the amount of subsidence.

Jan 1, 1982

By Kent D. Peaslee, Lifeng Zhang, Edith Martinez, Yufeng Wang

The current study investigated the multiphase fluid flow, heat transfer, solidification of the steel, and the motion and entrapment of inclusions during the centrifugal casting process using FLUENT software. User-defined functions (UDFs) were developed to add velocity with a value related to the rotation speed and radial distance to the solidified steel, to exert a centrifugal force to the motion of inclusions, and to add the entrapment condition of inclusions at the solidifying shell and export the entrapment locations of the inclusion. The calculation shows that there are two peaks of inclusions along the thickness of the produced tube: one at close to outer surface and another one close to the inner surface of the tube. With a larger rotation speed, inclusions tend to be entrapped more towards the inner surface. The calculation agrees well with the industrial measurements.

Jan 1, 2012

By G. R. Fritterer

INVESTIGATORS in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial tempera-tures; i. e., 1000° to 1800° C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree.

Jan 1, 1933

By D. R. Forshey

The recent occurrence of fatal accidents in copper mines, presumably due to premature ignition of loaded holes by the heat from reacting ammonium nitrate-fuel oil (AN-FO) and pyrite-bearing ores, has led to an examination of this reaction. The reactivity of prilled AN-FO mixtures with pyrite-bearing ores and the effects of water, dilute sulfuric acid, and potential inhibitors on reactivity of the mixtures were evaluated. Initiation of an exothermic reaction was observed as low as 150° F with acid in the absence of inhibitors. Low concentrations of urea, calcium carbonate, zinc oxide, and magnesium oxide were effective in inhibiting the reactivity of the mixtures. The temperatures produced during the reaction of mixtures of AN-FO and pyrite-bearing ores, in the absence of inhibitors, always exceeded the temperature at which electric blasting caps are thermally initiated.

Jan 1, 1968

Prof. Mathesius analyzes the running of Howland's furnace No. 19, according to the method described by him in Stahl and Eisen, 1916, Nos. 30 and, 31, and in his work "Die physikalischen und chemischen Grundlagen den Eisenhüttenwesens" (Spamer, Leipzig). By assuming 500 Cal. lost from the hearth by radiation and cooling water per kilogram of pig iron made, a throat-gas temperature of 600° C., and taking the ratio of C02/CO as 0.64, he finds that his diagram would show 0.68 kg. of carbon oxidized per kilogram of pig iron, while Howland gives 0.66 kg. He expresses himself as well satisfied with this test of the accuracy of his theory. Making the further assumption that the heat losses from the shaft are 1,000 Cal. per kilogram of pig iron (twice as

Jan 5, 1917

By Benjamin W. Haynes

The Bureau of Mines conducted research to devise technology for increasing the Nation's mineral supply by recovering valuable constituents from currently discarded waste materials. Municipal solid waste (MSW), presently a major disposal problem, represents a significant source of metals, glass, and a combustible fraction that can be used to supplement coal in generating heat and electricity. As part of the total metallurgical system to treat MSW, this study evaluates the combustible fraction of MSW to characterize the various combustible components and to identify the principal sources of elements that eventually may be objectionable from corrosive or environmental considerations. Several possible sources for cadmium, chromium, cobalt, copper, lead, nickel, and zinc have been tentatively identified. These sources are pigments, inks, paper stock, and additives to plastics. A correlation between industry consumption values and measured concentrations in MSW was found for several elements.

Jan 1, 1978