Search Documents

By Klaus Schwerdtfeger, Leo Zwell

The equilibrium between Ir-Fe or Rh-Fe alloys, iron oxide (wüstite or magnetite), and CO2-CO atmospheres has been determined at 1200°C. The data are used to derive the activities in these binary solid solutions. Both systems show negative deviations from Raoult's law. The lattice parameters are given for the investigated Ir-Fe and Rh-Fe alloys. IRIDIUM and iron form a continuous series of fcc solid solutions at elevated temperatures.' Rhodium-rich Rh- Fe alloys have fcc structure.' In the medium concentration range an ordered bcc phase is stable at temperatures up to about 1300°C. Phase relations in iron-rich alloys are not well-known. No thermody-namic data are available for these alloys. EXPERIMENTAL METHOD The experimental method used was to measure the equilibria between a gas phase of known CO2/C0 ratio, the alloy, and iron oxide (wüstite or magnetite). In one series of experiments the alloys of known composition were heated in CO 2-CO gas mixtures. After treatment (usually 1 day) the sample was quenched to room temperature and its surface examined visually to determine whether an oxide tarnish had formed. The procedure was repeated at slightly higher CO 2/CO ratios until the CO 2/CO ratio of incipient oxidation was found. Subsequently, the CO 2/C0 ratio was lowered again in small increments until the tarnish was reduced. In other experiments mixtures of alloy and iron oxide powders were pressed into pellets and equilibrated with the CO2-CO gas phase. In order to ensure that equilibrium was attained, two specimens with different starting iron content were heated side by side; in most cases, equilibrium was approached in one pellet by reduction of iron oxide and in the other pellet by oxidation of metallic iron. The sample was quenched to room temperature, and the composition of the equilibrated alloy was determined by X-ray measurements of lattice parameters and comparison of these values with calibration curves obtained from alloys of known composition. The oxides present in the specimens were identified by comparison of their diffraction patterns with those in the ASTM Card File. It may be expected from the noble character of iridium and rhodium that no appreciable amount of iridium or rhodium is dissolved in wiistite and magnetite under the present experimental conditions. The activity of iron in the alloy is then equal to that established in the iron oxide by the COrCO atmosphere. The activities of iron in wüstite and magnetite, as a function of oxygen pressure, were taken from the work of Darken and Gurry,

Jan 1, 1969

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry's use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel 'economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

By H. Fechtig, R. H. Buck, A. G. Guy

MULTIPHASE diffusion has been studied for many years in two-component systems1,2 and many of the experimental aspects are now fairly well understood.314 Although by no means all of the problems connected with the two-component case have been solved,' attention has recently been directed to the more complex situation involving three components. The pioneer work of Clark and Rhines6 yielded a qualitative picture of the types of behavior that can occur, and Clark7 has suggested conventions for describing the various phenomena. Kirkaldy and co-workers8,9 have made quantitative studies in several ternary systems and have offered explanations of the occurrence of isolated and nonisolated precipitates. At present, however, there is no comprehensive theory for the variety of phenomena observed in ternary, multiphase diffusion. By analogy with several studies that have been made of multiphase diffusion in the binary Cu-Zn system,2'10'11 a similar exploratory study was made of Cu-Zn-Ni alloys lying along the line in the ternary diagram from the point 80 Cu-20 Ni to the zinc corner of the diagram, Fig. 1. A principal question to be answered was whether initially plane interfaces would remain plane during the course of one-dimensional diffusion. The diffusion specimens studied are described in Table I. The five separate alloys from which they were made were melted in evacuated Vycor capsules from 99.9 pct purity copper, zinc, and nickel. Since some of the alloys were too brittle to be swaged, all of the alloys were used in the cast condition. To facilitate later homogenization, the molten alloys were solidified by plunging the capsule in water. Homogenization heat treatment was done at 720°C for 20 hr. The five nominal compositions in weight percent zinc and nickel, respectively, were: 37.5, 12.5; 44.0, 11.2; 50.0, 10.0; 55.0, 9.0; 65.0, 7.0. Ln Table I the alloys are identified only by their zinc content. Sandwich-type diffusion specimens were prepared by pressure welding disk specimens, each about 3 mm high by 10 mm in diameter. Welding was done in a special threaded vise which was heated at 500°C for about an hour in an atmosphere of flowing hydrogen. A measurement of the separation of the phase interfaces was made on a polished flat on the welded specimen, and then the specimen was sealed in an evacuated capsule and given the diffusion treatment shown in Table I. The diffused specimen was sectioned longitudinally

Jan 1, 1965

GEO. F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).-This interesting paper throws additional light on a question about which differences of opinion have apparently existed in the past, and the writer would like to record in this connection the agreement of his experience with that of Primrose and Prof. Smart in regard to the effect of quenching on the properties of gun-metal bronze. The writer's results have been published, so that there is no need for a detailed report, here, but his in-vestigations resulted in showing that both gun metal and manganese bronze are ruined by quenching in water from a red heat, apparently because they cannot stand the strains produced by the sudden cooling. The lines, mentioned by Prof. Smart, in a polished and etched section of the quenched metal have also been noticed by the writer, who however has not found them any different in quenched specimens than in annealed specimens. Since they appear only after etching, it would seem most probable that they are merely grain boundaries in most cases, though Prof. Smart's idea that they are indications of strains is by no means impossible. Fig. 1 shows how these lines appeared on the author's speci-mens of annealed gun metal, etched with ammonia and hydrogen per-oxide, and magnified 100 diameters.

Jan 11, 1919

By Oscar T. Marzke

Four alloys that precipitate the alpha phase from the beta of the copper-zinc system were heat-treated in various ways to develop as many forms of the segregate as possible. It was found that the precipitate may have the form either of plates or of needles. Plates usually result when precipitation occurs at low temperatures and needles when precipitation takes place at high temperatures. The needles tend to align themselves along certain planes in the matrix and to coalesce into plnte-like structures. The two phases were found to be related so that a (111) plane and [Oil] direction of the precipitate are parallel to a 10111 plane and 11111 direction of the matrix. DISCUSSION (E. A. Anderson presiding) D. W. Smith, Pittsburgh, Pa. (Written discussion).—Tllis report by Dr. Marzke covers completely all possible heat treatinents over a considerable range of compositiol~s in which a1pha precipitates from beta brass, and may be said to complete the Inctallographic part of this problern The lining up of ncedles of segregate to form plates, espeeially as shown in Fig. 5, appears to he regular, although the author's frequency plot in Fig. 11 makes it appear rather irregular. Has the author attempted anY correlation between some of the major dircetions and the oricntntaion of the parent grain as determined by X-ray analysis? Also, in Figs. 4, 5 and 6 the cross-sections of the needles appear to be straightsided and regular. Have these directions been correlated with the matrix latttice? Dr. Mnrzkr 's method of interpretation of the orientation rclationships between the alpha. and beta phases is a bit uncertain and seems to wed more explanation. If this relationship, as staited is such that :L (1111 plane and a [I 10] direction of that plane in the precipitate is parallel to a. {110} p1ane and a [111] direction of that, plane in the matrix, there mill be a maximum of 24 possible orientations of the alpha phase within a. single grain of the beta phasc. This relationship is expressed strercographical1y in Fig. 13, ill which the locations of a11 of the alpha {111} poles for the 24 orientations of alpha me given. Fig. 12 chccks fairly closely with this thcoretical plot,. with a few exeeptions which may be due to the inaceuracy inherent in the method used by the anthor in determining the orientations of the segregates. The method might have been refined somewhat had corrections been made for the displacement of the slip p1ancs upon deformation.

Jan 1, 1933

By W. N. Best

This paper is not intended as a scientific discussion of the combustion of oil but is written from the standpoint of an operator who has the experience and qualifications necessary to guide others in producing the most economical results in the use of liquid fuels. Oil, in this paper, usually means petroleum or its products but incidental reference is made to other liquid and gaseous fuels, so that the term may be considered as referring to all liquid and gaseous hydrocarbons in comparison with solid fuels, as coal and wood. However, only a few of the principal factors in the use of oil as a fuel can be given. The present, and prospective, high price of coal is causing users of fuel to renew inquiry as to the merits of other forms of fuel for industrial purposes. Crude oil (petroleum) is proving to be one of the world's most valuable mineral resources. The recent discovery that oil underlies a considerable area of the United States, Mexico, and other parts of the world to a greater extent than was formerly believed and the large production of some of the wells in these areas shows the probable quantity of fuel oil that may now be available. Through the energy of Lord Cowdrey, who was one of the pioneers of the oil industry in Mexico, oil has been discovered in England; some prominent geologists believe that it may be found in quantity in Great Britain. For years, oil has been known to be of great value in the manufneture of metals. It has proved incomparable in forge shops, steel foundries, heat-treating furnaces, and wherever accuracy of temperatures is essential, or where a maximum output is desired as well as quality of metal. In some types of equipment, the output produced with oil as fuel is double that obtained with coal and at a reduction of 50 per cent. in the cost of the fuel. For example, in drop-forging plants, the metal is always waiting for the man when oil is used as fuel, whereas with coal, the man must wait for the metal to become sufficiently heated. It has only been since January, 1919, that the oil supply could be relied on for boiler service, owing to the war conditions and the inability to get oil tankers for the delivery of the oil from Mexico to Atlantic ports; but now a constant supply is assured, and many manufacturers are installing it in their power plants. The cost varies with the size of the

Jan 1, 1921

By R. W. Gurry, L. S. Darken

The solubility of cementite in austenite is computed by thermodynamic methods from the observed solubility of graphite. It is found that the solubility of cementite is greater than that of graphite in the entire austenite temperature range. Thus the prior discrepancy between this portion of the phase diagram and the observed metastability of cementite is partially resolved. FOR several years it has been apparent that a serious discrepancy exists in certain observations pertaining to the Fe-C system. Direct experimental data indicate: 1-That the curve representing the solubility of graphite in austenite'" crosses that for cementite4 at about 945°C as shown in Fig. 1. 2— That graphite and austenite saturated therewith are stable1 relative to cementite at all temperatures between the eutectoid, about 723°C, and the eutectic, about 1153°C. These observations are mutually incompatible in view of a well-known consequence of the second law of thermodynamics, namely, that the stable phase (presumably graphite at all temperatures) has a lower solubility than the metastable phase (presumably cementite). Hence either 1 or 2 above must be in error; either the measured solubility of graphite or of cementite, or the observation as to the stability of graphite, is in error. Our present purposes are: 1—To collate the available data on cementite and prepare a table of HO — HO° and of (Fa— HO°)/T. This tabular method seems the best and most convenient way to represent the heat and free energy of formation. 2—To determine whether the measured solubilities of cementite and graphite in austenite are in accord with the above table and the measured thermodynamic properties of austenite, in order to resolve, if possible, the existing paradox of these two solubilities. Enthalpy of Cementite The enthalpy of cementite at 273 °K, H279 — HOcem, was computed by integration of the low temperature heat capacity as measured by Seltz, McDonald, and Wells" 68" to 298 °K) and as given by the Debye functions recommended by them (0" to 68°K); the result is included in Table I. At higher temperature HCem — H,,"" is given by Kelley who used the data of Naeser7 (298" to 1037°K) and of Umino8,9 (273° to 1923°K). We have recalculated Hcem — H273 cem from the data of UminoO in the following way. In the equilibrated alloy at temperature the weight fraction of cementite Pct c -Pct cr is PctC -PctCr designated f(C), and the

Jan 1, 1952

By Michael Michaylov

INTRODUCTUCTICN The coal seams at Bobov dol basin are highly prone to spontaneous combustion in Bulgaria. The risks of endogenous fires (SPONCOM) exist mainly in gob area. During the last 15 years three different technologies for preventing and fighting SPONCOM have been applied in underground mines of this basin: pulp from hard material and water, foam and inerting with nitrogen. On the basis of experimental application of these technologies as well as theoretical and experimental research a new technology - Foam Pulp Technology (FPT) was worked out. It is very effective in difficult to reach places in a gob. BACKGROUND AND THE NEED OF FPT Application of the three methods mentioned above showed advantages as well as some disadvantages, allowing determination of their effective application scope depending on geological and working conditions. Their advantages can be summarized as follows: - Foaming: high viscosity at low density, which allows forming a thick layer; good surfactant wetting properties; excellent effective cooling during evaporation in high temperature zones. - Pulping with mixture of solid particles (e.g., fly ash) and water from surface installation: easy to apply in a mine; low operational and energy costs due to gravity transport from the surface to the gob: good ecological results because the waste material is returned back underground. - Inerting with nitrogen: volumetric action which doesn't restrict the thickness of treated coal pile; easy to apply in a mine; controllable nitrogen delivery depending on fire hazard conditions. Main disadvantages of the same three methods are: - Foaming: rapid disintegration due to intrusion into heterogeneous and porous media and high costs due to the need of frequent large volume foam flows (short foam's life); - Pulping: inapplicable for coal piles with high thickness which is of great importance in the cases of seams with ununiform hypsometry (rapid and frequent changes in a seam configuration) and/or great volumes of coal or ore piles particularly heated to a high temperature; strong dependence on gob floor declination; water draining of the working face area which impedes the movement of supports and chain conveyor's. - Inerting: relatively high costs hardly depending on the rate of face advance (fig.1) in comparison with the other methods; it is difficult to ensure sufficient oxygen at the exit end of the face. This problem is crucial in faces with a high level of methane emissions; accelerating of the oxidation and spontaneous heating of the pile after turning off the nitrogen supply. Inerting should be applied again at higher capacity of nitrogen supply (fig.2) and what is more important, it shouldn't be

Jan 1, 1995

By Joel F. Flurnerfelt

Molten Al and Al alloys containing si, Mn, Ti, and y have been lanced with nitrogen-bearing gases. These lancing experiments provided the means for observing what phases form during exposure to nitrogen-bearing gases for finite periods of time, <2 minutes, at high temperatures, >1290oC. The experiments were conducted in sn induction heated drop tube furnace apparatus. The overall premise of these experiments was to select those Al alloys and gas compositions that show promise of forming secondary dispersoid phases, particularly AIN, in the Al matrix. The alloys selected will be atomized using gas atomization reaction synthesis (GARS) using the most favorable conditions. In this case, the chosen Al alloy will be atomized with a nitrogen-bearing gas, such that the Al and gaseous nitrogen species react to form a dispersoid phase within each powder particle. The powder particles that result from this "aggressive" GARS-process would be essentially Al metal-matrix composites within a uniform distribution of dispersoids. To date, only high-purity Al has been atomized using a mild GARS reaction. This work is funded by the Materials Science Division of DOE-BES under contract number W-7405-Eng-82.

Jan 1, 1996

By Francis B. Foley

Fundamentally, slag control in acid open-hearth steelmaking cannot be considered from any different viewpoint than can that in basic open-hearth melting. The same laws of mass action and distribution apply in both cases, so that while most, if not all, of the recent intensive study of slag-metal reactions have been carried on in basic furnaces the principles evolved are nevertheless applicable to acid open-hearth steelmaking and it is therefore not our intention to discuss the various possible chemical reactions in the slag and between slag and metal. The points we have to carry in mind, in considering acid melting practice, are the differences in the type of steels produced and the difference in the chemistry of both the steel and the slag. The acid furnace is used to produce, let us not say "quality" steel, for, after all, a "quality" steel for one purpose is not a "quality" steel for another, but steels that require acid melting practice to be of proper "quality." Steels that are required to have high physical properties in tests taken transversely from forgings are peculiarly the product of acid furnaces. In this class may be placed various ordnance materials, notably gun forgings and projectiles and large commercial forgings requiring high transverse ductility. Forgings requiring an extremely hard surface, polished and free from imperfections, are also typical acid-steel products. Of course, such forgings can be made of basic open-hearth steel, but not with the same assurance of success. At the start, the preparation of the slag in the acid and basic furnaces differs. Lime is charged in the beginning of a basic heat to form a slag, but in the acid furnace nothing is added for the special purpose of producing a slag when the heat is melted down. The result is that the acid furnace has much less volume of slag than the basic. The slag formed upon melting down is made up almost entirely of the oxides of elements contained in the metallic charge, notably oxides of iron, manganese and silicon, the amount of silica being augmented somewhat by erosion of the furnace lining. A typical acid open-hearth slag, when the bath is completely melted, will have an analysis about as follows: CaO, 3.40 per cent; SiO2, 51.9; Fe2O3, 1.25 ; FeO, 28.86; Al2o3, 1.82; MnO, 12.22. The high iron oxide content of the slag gives it a black appearance. The metal is high in carbon and some manganese and silicon will be present, depending on the amount in the original charge, the amount of

Jan 1, 1935

By Francis B. Foley

Fundamentally, slag control in acid open-hearth steelmaking cannot be considered from any different viewpoint than can that in basic open-hearth melting. The same laws of mass action and distribution apply in both cases, so that while most, if not all, of the recent intensive study of slag-metal reactions have been carried on in basic furnaces the principles evolved are nevertheless applicable to acid open-hearth steelmaking and it is therefore not our intention to discuss the various possible chemical reactions in the slag and between slag and metal. The points we have to carry in mind, in considering acid melting practice, are the differences in the type of steels produced and the difference in the chemistry of both the steel and the slag. The acid furnace is used to produce, let us not say "quality" steel, for, after all, a "quality" steel for one purpose is not a "quality" steel for another, but steels that require acid melting practice to be of proper "quality." Steels that are required to have high physical properties in tests taken transversely from forgings are peculiarly the product of acid furnaces. In this class may be placed various ordnance materials, notably gun forgings and projectiles and large commercial forgings requiring high transverse ductility. Forgings requiring an extremely hard surface, polished and free from imperfections, are also typical acid-steel products. Of course, such forgings can be made of basic open-hearth steel, but not with the same assurance of success. At the start, the preparation of the slag in the acid and basic furnaces differs. Lime is charged in the beginning of a basic heat to form a slag, but in the acid furnace nothing is added for the special purpose of producing a slag when the heat is melted down. The result is that the acid furnace has much less volume of slag than the basic. The slag formed upon melting down is made up almost entirely of the oxides of elements contained in the metallic charge, notably oxides of iron, manganese and silicon, the amount of silica being augmented somewhat by erosion of the furnace lining. A typical acid open-hearth slag, when the bath is completely melted, will have an analysis about as follows: CaO, 3.40 per cent; SiO2, 51.9; Fe2O3, 1.25 ; FeO, 28.86; Al2o3, 1.82; MnO, 12.22. The high iron oxide content of the slag gives it a black appearance. The metal is high in carbon and some manganese and silicon will be present, depending on the amount in the original charge, the amount of

Jan 1, 1935

By W. H. Gunniss

When the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of an average sample of this quartz is: SiO2, 96.7; Fe2O3, 0.3; Al208, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then dumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the material would not be plastic enough to mold. After a few minutes&apos; grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left. until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected to when in use in the furnaces. Montana refractories are used in smelters throughout the West. Prospecting for fire clays was also carried on. After experimenting with clays from several different deposits, it was found that a mixture of

Jan 1, 1914

By C. Chiou, D. P. Seraphim

The effect of clustering on the superconducting properties of Al-Zn alloys has been studied by the ballistic induction techniques. The superconducting critical temperature, T,, changes when zinc-rich clusters are formed. The change in T, depends on the concentration and may be positive or negative, but always correlates with an effective decrease in the solute concentration of the alloy. Reversion after clustering effectively returns a 5 at. pct Zn alloy to the quenched state. These methods might be use&lly extended to the Al-Mg system, where X-ray data are difficult to obtain. In very dilute Al-Zn alloys, as in other tin,&apos; indium, aluminum,2 or tantalums base solid solutions, there is a decrease in the superconducting critical temperature, Tc, roughly proportional to the temperature independent resistivity, i.e., -0.2°K per pS2cm. With increasing solute concentration, the T, generally reaches a minimum and then increases4 to a value well above that for the pure solvent. The change of T, with solute concentration follows an empirical formulation involving two constants which correlate with the scattering cross section of the impurities. As will be shown below, the Al-Zn alloys more concentrated than 1or2at. pct do not follow the empiricism, probably because they are unstable even when rapidly quenched.5 However, it seems possible to study at least the later stages of solute clustering by precise measurements of the 1&apos;, following various thermal treatments. A few experiments on quenched alloys, aged alloys, and tests on reversion are reported here. The heat treatments selected for obtaining the quenched and aged states were mainly deduced from the work of Dash and Fine.6 For the quenched state, specimens were homogenized at 480°C, quenched to -160°C, and immediately transferred and mounted in liquid nitrogen. Measurements on the superconducting properties and residual resistivities were then made at helium temperatures, after which the specimens were aged at room temperature for 3 to 5 hr, i.e., much longer than the time required for clustering to be essentially completed. The superconducting properties and residual resistivities were once again examined. To reach the reverted state of the A1-5at. pct Zn alloy, the aged specimen was heated for 5 min at 200°C and then tested as above.

Jan 1, 1963

By Walter O. Snelling

In the course of some experiments more than five years ago, made for a totally different purpose than the investigation of the oil used, I placed a small quantity of a transparent yellow lubricating oil in a bomb-like vessel and heated it to a relatively high temperature. At the end of the experiment I removed the oil from the vessel and was amazed to find that instead of bearing any resemblance to the oil which I had put in, it now had the appearance of ordinary crude oil. The green color by reflected light and the rich red-brown by transmitted light were so unmistakable as to at once lead to further investigation. I subjected the material to fractional distillation, and the surprise which I experienced at the appearance of the oil, changed to amazement when I found that it yielded, on distillation, 15 per cent. of gasoline and 30 per cent. of burning oil, and that its constitution resembled crude oil quite as much as did its appearance. Furthermore, the gasoline and kerosene distillates which it yielded were of a clear water-white color, entirely without treatment with acid or alkali, and were entirely free from the odor familiar in "cracked" petroleum distillates. The result of this experiment was quite too remarkable to be credited without further confirmation, and I at once filled the vessel with some of the same oil that I had used before, and again heated to about the same temperature that I had previously used, and for the same period of time. Upon opening the vessel and removing the contents I found, not the material resembling crude oil that I had obtained before, but apparently only the same oil that I had put in, somewhat darkened in color, but nevertheless far different in appearance from the material obtained in the previous experiment. Evidently some condition existed in the first experiment that had not existed in the second test, and here began a series of tests in which I sought by the change of one variable after another to arrive at the identical conditions which must have existed in the first experiment. Only the fact that the bottle of heavy oil used in the first test was still in its place,

Jan 1, 1915

By George W. Maynard Maynard

IN this paper I desire to embody the results of some personal observations of the working of the Siemens direct process as I witnessed it for a part of three days at the works of the Siemens-Anderson Company, in Pittsburgh. This preliminary investigation was to have been followed up by one extending over a considerable period of time, and would have embraced analytical and physical tests. Circumstances over which I had no control, resulting in the temporary suspension of work, have postponed the presentation of a complete paper. If the opportunity is afforded me, I purpose doing this at a future meeting of the Institute. To those interested in the development of the process, reference is made to the papers of Dr. Siemens in the Journal of the Iron and Steel Institute for the years 1873 and 1877, and to the paper of our late lamented brother, Holley, in the 8th volume of the Transactions of our own Institute. Dr. Siemens, in the introduction to his paper "On the Manufacture of Iron and Steel by Direct Process," read before the Iron and Steel Institute in September, 1877, says: " In mixing comparatively rich iron ore in powder with about 25 per cent. of its weight of pounded coal, and in exposing this mixture for some hours to the heat of a common stove or of a smith&apos;s fire, metallic iron is formed, which, on being heated to the welding-point on the same smith&apos;s hearth, may be forged into a horseshoe of excellent quality. The admixture with the ore of some fluxing materials, such as lime or clay, will, in most cases, be of advantage to rid the iron of adherent slag." This is the keynote of the Siemens direct process. Dr. Siemens says further: "If we regard the production of wrought iron from an abstract point of view, we perceive that we have to accomplish two things, viz., the deoxidation of the ore, and the fusion of the earthy matter .mixed with it; and if we calculate the amount of carbon necessary to accomplish this end, we shall find that in using, say, hematite ore, consisting of peroxide of iron with from 10 to 15 per cent. of silica, we shall require barely 40 per cent. of carbonaceous matter per ton of iron contained in the&apos; ore to effect its reduction, and also the fusion of the slag."

Jan 1, 1882

By C. R. Fondersmith, John Chipman

In the manufacture of rimming steel—which constitutes the bulk of the world&apos;s production of mild steel—the factors that determine the quality of the product are very closely associated with the pouring and solidification of the steel in the ingot mold. The behavior of the metal in the mold is, on the one hand, the resultant of the complex processes through which the liquid metal has passed, and, on the other, it is an indication of the probable behavior of the ingot during subsequent rolling and finishing operations. A detailed study of the mechanism of solidification of rimming ingots ought to yield information that will be useful in controlling the structure of the ingot and the quality of the ultimate product. The first step in such a study is to determine the rate at which the solid shell of the ingot forms from the liquid metal in the mold. A knowledge of the rate of solidification will make it possible to correlate observations of rimming action and gas evolution with studies of the structure, porosity, and segregation within the ingot. Thus, if the metal in the mold is observed to fall, let us say one minute after pouring, the portion of the structure associated with this fall will be located in the part of the ingot that is solidifying at that particular moment. The knowledge that the ingot solidifies to a depth of 3/4 in. in the first minute enables us to locate in the ingot the structural features corresponding to the observed fall. Conversely, the blowhole condition associated with a rising or growing ingot will be found in the part of the ingot that is solidifying at the time the phenomenon occurs. The time required for the complete solidification of an ingot has long been a matter of speculation. It is of considerable practical importance in connection with charging and heating in the soaking pits. Too rapid handling of the ingot through heating and rolling processes has been thought to be associated with excessive pipe and other internal defects, so that a further object of this investigation was to attempt to estimate the time required for complete solidification, or the minimum practical time within which the subsequent operations can be performed with the minimum hazard.

Jan 1, 1937

By G. W. Maynard

In this paper I desire to embody the results of some personal observations of the working of the Siemens direct process as I witnessed it for a part of three days at the works of the Siemens-Anderson Company, in Pittsburgh. This preliminary investigation was to have been followed up by one extending over a considerable period of time, and would have embraced analytical and physical tests. Circumstances over which I had no control, resulting in the temporay suspension of work, have postponed the presentation of a complete paper. If the opportunity is afforded me, I purpose doing this at a future meeting of the Institute. To those interested in the development of the process, reference is made to the papers of Dr. Siemens in the Journal of the Iron and Steel Institute for the years 1873 and 1877, and to the paper of our late lamented brother, Holley, in the 8th volume of the Transactions of our owu Institute. Dr. Siemens, in the introduction to his paper "On the Manufacture of Iron and Steel by Direct Process," read before the Iron and Steel Institute in september, 1877, says: " In mixing comparatively rich iron ore in powder with about 25 per cent. of its weight of pounded coal, and in exposing this mixture for some hours to the heat of a common stove or of a smith&apos;s fire, metallic iron is formed, which, on being heated to the welding-point on the same smith&apos;s hearth, may be forged into a horseshoe of excellent quality. The admixture with the ore of some fluxiug materials, such as lime or clay, will, in most cases, be of advantage to rid the iron of adherent slog." This is the keynote of the Siemens direct process. Dr. Siemens says further: " If we regard the production of wrought iron from an abstract point of view, we perceive that we have to accomplish two things, viz., the deoxidation of the ore, arid the fusion of the earthy matter mixed with it; and if we calculate the amount of carbon necessary to accomplish this end, weshall rind that in using, say, hematite ore, consisting of peroxide of iron with from 10 to 15 per cent. of silica, we shall require barely 40 per cent. of carbonsceous matter per ton of iron contained in the ore to effect its reduction, and also the fusion of the slag."

Jan 1, 1882

By William R. Webster

I have continued the investigation of the Pottstown Iron Com pany&apos;s basic Bessemer keel plates on the line referred to in my paper of last October (Trans., xxi., 766)) and have added a study of the hardening effects of sulphur, which were not taken into account at that time. The results are so encouraging that I now give them in full. For some months we have graded all the steel at these works by the table given in my former paper, and checked the grading by the forging-tests as described in the paper of Mr. Joseph Hartshorne, read at the same meeting (Trans., xxi., 748). The steel thus graded was bloomed for the plate orders. Then one slab was rolled into a plate for the order, and a tension-test was made of this plate. By the result of this tension-test we were guided in rolling the balance of the heat. Out of several hundred heats graded in this manner, 95 per cent. met the requirements of the orders in every respect, and were accepted; but these results will no doubt be improved upon, when the influence of sulphur is also considered.. The hardening effect of sulphur seems to be about 500 pounds per each .01 per cent. of increase. In the table accompanying the pres ent paper, the ultimate strength with .06.5 per cent. sulphur agrees with the old table where sulphur was not considered; that is, for all steels with less than .065 per cent. sulphur we now get lower re sults, and for those with more sulphur, higher results. Making this allowance for sulphur, the assumed ultimate strength of a 3/8-inch plate of pure iron is reduced from 38,000 pounds per square inch to 34,750 pounds. With this as a basis, I have constructed my new table, giving each of the elements, carbon, phosphorus and manganese the same hardening effect as before, to wit : Carbon is credited with a constant effect of 800 pounds per each, 0.01 per cent. Phosphorus shows greater effect in high-carbon than in low-carbon steels. For 0.07 and 0.08 C, it has about the same effect as carbon, that is, 800 pounds for each .01 P. This increases to 1500 pounds per .01 P in 0.15 C steel, or nearly twice the effect of carbon. This

Jan 1, 1894

By Rustu S. Kalyoncu

Rainbow colors of roofing granules, adorning the roofs of buildings from single family units to largest office buildings, have their origin in the roofing shingles as burlap soaked with tar appearing as early as the 1700s. Dusting of talc and mica on the coated surfaces, to keep roofing from sticking to itself in storage, represents an early improvement to the original construction product. Sometimes, colored, natural mineral dusts were added as color pigments within the dusting material, for initial color. Prolonged exposure to sun caused the asphalt to become brittle, and it eventually cracked and leaked. Search for solutions to cracking and subsequent leaking problems eventually led to the use of crushed mineral granules on asphalt coated shingles. This provided the impetus for further growth in the asphalt roofing industry. Application of a layer of crushed mineral on the asphalt coating minimized the coating deterioration from exposure to ultraviolet light, thus significantly improving the shingle life. In the 1900s, screened waste from slate quarries was the most commonly used granule in asphalt roofing products. Records indicate the use of coarse slate screenings for asphalt roofing as early as 1906. As the asphalt roofing industry further developed, other naturally colored minerals, such as silica sand, quartz, mica, feldspar, talc, slag, granite, rhyolite, and oyster shells were used on roofing surfaces. Later on, a number of manufactured granular materials, such as crushed brick and tile, fire clay, and white porcelain were used. The first artificially colored roofing granule was produced in 1914 by running molten slag into a solution of alkaline metal silicate, which was absorbed by the porous slag. Various colors were obtained by adding pigments to the silicate coating and by subsequently heat treating the granules. In 1922, another technique was developed in which green slate granules were saturated with copper sulfate solution and heated to 760°C to form copper oxide. Since then, many other granule coloring processes have been patented, one of the most significant being the sodium silicate coatings introduced around 1975. Granules as used in construction (specifically roofing materials) are defined as natural or synthetic-mineral grains smaller than gravel and larger than sand in particle size. They are used primarily for protective and decorative purposes on the weather- exposed surface of asphalt composition roofing. Development of artificial coloring techniques has made it possible for the roofing industry to provide asphalt roofing shingles in a wide variety of colors complementing the color and style of buildings. Roofing granules, as we see today, are the products of long technological evolution.

Jan 1, 1994

By W. W. Cotter, W. R. Clark

WEBSTER tells us the word "extrude" means to "force, press or push out; to protrude." As applied to the metal industry, the process consists largely of forcing plastic elements (plasticity usually obtained by preheating), through dies of predetermined profiles, into constant sections of considerable length and weight. Most of the "virgin" metals are quite malleable under this process, likewise many of the commonly used "alloys" in various industries, when basic elements are proportioned or combined within the natural laws and limits of good metallurgy. Several of the foundry alloys, both ferrous and nonferrous, together with some of the heat-treatable light metal mixtures, are decidedly weak and hot short at ordinarily plastic ranges, and consequently are troublesome or quite incapable of commercial extrusion. DEVELOPMENT OF PROCESS This process was conceived some time before 1800 and during its first century was employed almost entirely in making lead pipe, plumbing fittings and coating electrical cables. As a result of contact and experience with the lead industry and presses, Alexander Dick, of London, England, is credited with first having applied the principles of extrusion to brass, and in 1894 brought out a 500-ton horizontal press powered by hydraulics. A duplicate of this unit was imported by one of the Connecticut brass mills and was in experimental operation by 1900. During the first five years of operation, this press proved the value of the method to American industry, as it immediately revolutionized and converted the manufacture of brass rod from a 15-pass cold-rolling operation, with elimination of several intermediate anneals and cleanings, to an extrusion and a finishing draw. Likewise, ornamental brass and bronze moldings formerly cast and machined were produced in one squeeze on the extruder. The extrusion operation, being entirely that of compression, deforms the material without tensile stresses and can be used on delicate mixtures under heat, which cannot be hot-worked by straight hot-rolling or roller piercing. Base slabs of clock-brass strip were early in line of development or improvement, as were the brass bronzes (Naval brass, Muntz metal, manganese bronze, and others), popular as engineering materials for bolt stock, as well as structural shapes for marine and other mild conditions of corrosion. By 1910, American engineers undertook to design tube shell extruders, but were unsuccessful. The first World War began before fabricators could procure the more substantial designs of tube extruders produced in Germany; and it was not until the middle twenties that better models of the Universal extruders (double-actioned presses), equipped with hydropneumatic accumulator systems and other modern equipment, were available in the United States.

Jan 1, 1945