Search Documents

By Steven A. Bradbury

INTRODUCTION Passive dust control systems are quickly gaining acceptance in the bulk solids handling industries. The number of applications is increasing due to proven performance, especially in US power plants burning Powder River Basin coal. Air Control Sciences ®, Inc., of Boulder, Colorado, has over forty (40) patented Dustless Transfer ® systems in operation. All of the installations control workspace dust levels to less than 2.0 mg/m3, and in some applications reduced conveyor dusting by over ninety-eight percent (98%). Passive systems control fugitive dust emissions by minimizing the induced airflow in bulk material transfer and slowing its velocity. Traditionally, fugitive dust control in the mining industry was accomplished using either dust collection systems or dust suppression systems. The term passive dust control, indicates these methods don't use any active dust collection or suppression. Passive dust control systems are best suited to transfer from one conveyor to another. They can also be applied to transfers from feeder to conveyors.

Jan 1, 2004

By Lijun Xu, Ragula Bhaskar

The transport of dust particles from a turbulent air stream on to the surface of a mine entry is mainly due to the effect of diffusion, sedimentation and inertial impaction. While the literature in aerosol science contains many references on particle deposition, most studies apply to smooth surfaces in small, short tubes. The deposition data from those experiments may not be applicable to deposition in mine airways that have large areas of rough surfaces and extend several thousand meters. This paper describes the mechanisms of mine dust transportation and deposition, specifically, by estimating the turbulent deposition velocity for coal dust in mine airways. Data from in-mine experiments on ambient dust concentration and dust deposition along a straight entry were used. A statistical model for dimensionless turbulent deposition velocity was developed, and compared with the models developed by other researchers. The model shows that the distance from the dust source is an important factor in the turbulent deposition of mine dust.

Jan 1, 1995

By B. J. Arnold

With the passing of the 1990 Clean Air Act Amendments, many utilities are opting to switch to lower sulfur coal to meet new SO2 emissions requirements. This lower sulfur coal may be from new suppliers or it may be from current suppliers that modify existing cleaning plants or build new plants to produce this higher quality coal. New, sophisticated coal cleaning simulators are useful tools for optimizing cod cleaning circuit operating parameters to maximize the production of clean coal that meets more stringent specifications for SO2 emissions potential. The examples in this paper were developed using the Coal Cleaning Simulator (CCS), running under ASPEN PLUS™, that was developed under a Department of Energy project cosponsored by the Electric Power Research Institute. With advanced sensitivity analysis and optimization features, CCS allows a quick, efficient, cost-effective review of coal cleaning plant performance to meet current production goals and to plan future changes in plant operating parameters or circuitry configurations.

Jan 1, 1995

By J. L. Bill

The capacity of the Mount Isa Mimes Limited Copper Smelter was expanded in 1998 from 180,000 tomes per year of anode copper to 265,000 tpy. It is based on the innovative Copper ISASMELT technology, which currently treats concentrate at up to 184 tph. Increasing lance-air oxygen enrichment increased the ISASMELT furnace feed rate from 102 to 184 tph. The increased feed rate was achieved without any modifications to the ISASMELT furnace. The first refractory campaign following the upgrade lasted for two years. Future campaign lives of four years or more--without water cooling-are possible. Other Copper ISASMELT furnaces are operating in the U.S.A., Belgium, and India, with additional smelters under construction in China and Germany. In addition, Lead ISASMELT furnaces are operating in the U.K. and Malaysia. The paper discusses the performance of the MIM Copper ISASMELT furnace and the Copper Smelter since the expansion, including operating data and refractory performance.

Jan 1, 2002

By Edward D. Thimons, Jay F. Colinet

Underground coal mining operations in the United States continue to increase productivity as mining equipment and practices are improved. Unfortunately, increased production also results in the potential for increased respirable dust generation and worker exposure. In response, US operations are applying basic controls at elevated levels and looking to emerging technologies in an effort to better control respirable dust levels. Ventilating air and water sprays remain the basis of dust control strategies for both longwall and continuous mining operations, and the level of application for these controls continues to increase. In addition, new technologies are emerging that have the potential to further reduce dust levels. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research into methods to optimize existing control technologies and evaluate emerging control technologies. This paper will summarize control technologies routinely being used in underground coal mine operations, as well as provide a review of new controls that are being pursued.

By Gerald H. Luttrell, Joe Shoniker, Jaisen N. Kohmuench, Christopher J. Barbee, Michael J. Mankosa

The HydroFloat technology was specifically developed to upgrade phosphate sands that are too coarse (>0.6 mm) to be efficiently recovered by conventional flotation methods. In this novel process, classified feed is suspended in a fluidized bed that has been aerated using an external sparging system. The air bubbles selectively attach to particles that have been made hydrophobic through the addition of a fatty acid collector. The teetering effect of the fluidized bed forces the low-density bubble-particle aggregates into the overflow, while hydrophilic particles are rejected as a high solids content underflow Since the HydroFloat is actually a density separator, the process can treat much coarser feeds than would be possible using traditional flotation processes. In addition, the high solids content of the teeter bed promotes bubble-particle attachment and reduces the cell volume required to achieve a given capacity. This paper presents test data from ongoing pilot-scale trials of the HydroFloat cell in the phosphate industry.

Jan 1, 2002

By F. N. Kissell, C. D. Litton

This study ranks the factors impacting survival during a coal mine fire. It has already been established that reducing time delays is the most important factor in saving lives. Consequently, every event during afire is measured in terms of its duration, and the effectiveness of any action taken to improve survival is measured in terms of the time it saves. By ranking actions according to time saved, these authors found that a combination of actions was most effective. This combination was: •installing lifelines, •moderately decreasing air leakage and •decreasing the fire growth rate. Changing ventilation leakage alone was much less effective, as was altering the CO (carbon monoxide), sensor alarm threshold. These results confirm an earlier fault-tree study on escape from mine fires. The fault-tree study had shown that, with the exception of delays, single-factor changes have minimal impact. Significant reductions in fire fatalities only take place with multiple factor changes.

Jan 1, 1994

Measure the daily exposure of individual miners to alpha particles emitted by radon daughters (radioactive decay products of the radon gas present in the mine atmosphere). Approach A dosimeter worn by a miner counts alpha particle emissions from radon daughters, RaA (Polonium 218) and RaC (Polonium 214), collected on a filter, and stores the gross count for later readout. How It Works A pump draws air into the detector assembly where radon daughters are collected on a filter. The detector, a solid state surface barrier type, is mounted in the filter head behind a thin mylar disc which serves as a moisture barrier. When a radon daughter decays and its alpha emission strikes the detector, the alpha particle causes a pulse of electrical charge in the detector. The circuits used to condition and count the electrical pulses generated in the detector are represented by the other blocks shown in the simplified block diagram. Each pulse is first amplified.

Jan 1, 1979

By Kim Fagerlund

A novel apparatus for studying refractory infiltration and dissolution/degradation under a temperature gradient was developed. To supersede conventional isothermal refractory testing, a new temperature gradient technique, based on a crucible equipped with a cooling element, has been developed to provide practical information on the penetration and dissolution of refractory materials under cooled conditions. This technique was adopted and applied to several refractory-slag systems. Commercially available magnesia chrome refractory bricks against a copper-containing calcium ferrite type of slag were tested and compared using both a conventional crucible test and the new temperature gradient method. The experiments were conducted at 1300-1420°C under a controlled atmosphere of nitrogen or air. It was noticed that the type of porosity has a significant effect on infiltration of magnesia chrome refractories. Furthemore, the copper-containing calcium ferrite slag caused a severe slag attack and refractory failure in some cases, due to its fluidity and corrosive nature.

Jan 1, 2002

By Richard Jr. Ray, Richard Druesedow

The Virginia Operations of Consolidation Coal Co. include a diversity of mine fan configurations which have been tested to quantify pressure losses through the inlet ductwork. Airflow and pressure measurements were taken at four shaft sites to calculate losses for the 90-degree bend at the top of the shaft and the self-closing dampers or closing doors located between the shaft and fan. Velocity contours were then developed from the test data to determine flow patterns in each fan system component. In addition, yaw and pitch angles of airflow through the fan annulus were measured to evaluate turbulence levels created by various inlet ductwork designs. The test results indicate that proper design of the shaft collar and ductwork arrangement for main mine fans can substantially reduce system pressure losses and air turbulence. BY minimizing the pressure drop experienced on the surface, these design improvements enable the bulk of the total pressure developed by the fan(s) to be utilized in the mine.

Jan 1, 1995

By Thomas F. Tomb

The penetration characteristics of a horizontal plate elutriator and of a 10-mm nylon cyclone were evaluated. The test aerosols were polydisperse coal-dust particles ranging from less than 0.3 to 15 micrometers in diameter. Particle densities ranged from 1.3 to 1.4 grams per cubic centimeter. Equivalent Stokes diameters were measured using Coulter counter analytical techniques. Experimental results indicate that the penetration characteristics of the horizontal plate elutriator closely approximate the sampling efficiency curve defining the respirable fraction of the dust cloud recommended and adopted by the Johannesburg Pneumoconiosis Conference in 1959. Penetration characteris-tics of the 10-mm cyclone were evaluated at flow rates of 1.4, 1.5, 2.0, 2.5, and 2.8 liters of air per minute. The data indicate that the penetration curve obtained at 2.0 liters per minute most closely approximates the sampling efficiency curve for respirable dust recommended at a meeting sponsored by the U.S. Atomic Energy Commission in 1961.

Jan 1, 1970

By G. T. Adel

The selective recovery of fine particles by flotation has been a long-standing problem in the mineral processing industry. Fundamental studies carried out at Virginia Tech since 1980 have suggested that many of the problems encountered in separating fine particles can be alleviated by using significantly smaller air bubbles than those used in conventional flotation processes. The main advantage of using smaller bubbles is found in an increased recovery rate, which can be attributed to an improved bubble-particle collision efficiency. This concept has been applied in column flotation as a means of improving flotation kinetics. A computer simulator has been developed to better study the effects of various parameters on flotation column performance. The simulation results suggest that the use of small bubbles and tall columns improves the recovery of fine particles while a judicious use of wash water greatly improves product quality. Information collected as a result of this analysis has been applied in developing scale-up relationships for column flotation.

Jan 1, 1989

By Cutmore NG

The moisture content of iron ore is important in handling, stockpiling, transport and further processing operations. Typically these ores contain both `free' and `bound' moisture, the latter being moisture that is not removed in a conventional laboratory determination of moisture by air drying at 105¦C, and it is the free moisture that is important in dust control and ore handling. The CSIRO Division of Mineral and Process Engineering has previously developed and commercialised gauges, based on capacitance and microwave techniques, for the on-belt determination of moisture in coal and minerals. However, these gauges determine total moisture, and have a different sensitivity to free and bound moisture in the material analysed. Consequently, the accuracy of determining total or free moisture alone may be significantly affected by variations in the bound moisture content. An investigation has been carried out on the simultaneous determination of free and bound moisture in iron ore fines (

Jan 1, 1993

By K. H. McDaniel, K. G. Wallace

This paper describes the development of a Windows-based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant (WIPP). To enhance the operation of the underground ventilation system, Westinghouse Electric Corp. developed a program called WIPPVENT. While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC from Mine Ven- tilation Services Inc. and uses the same subroutine to calculate airflow distributions, the user interface was completely rewritten as a Windows application with screen grap-hics. WIPPVENT is designed to interact with WIPP ventilation-monitoring systems through the sitewide central monitoring system. Data (e.g., air quantity and differential pressure) can be continuously collected from the underground ventilation remote-monitoring and control system and from the mine's weather stations (psychrometric data). Furthermore, WIPPVENT incorporates regulator characteristic curves specific to the site. The program utilizes this data to create and continuously update a real-time ventilation model. This paper discusses the design, the key features and the interactive capabilities of WIPPVENT.

Jan 1, 1998

By K. H. McDaniel

This paper describes the development of a Windows-based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant (WIPP). To enhance the operation of the underground ventilation system, Westinghouse Electric Corp. developed a program called WIPPVENT. While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC from Mine Ventilation Services Inc. and uses the same subroutine to calculate airflow distributions, the user interface was completely rewritten as a Windows application with screen graphics. WIPPVENT is designed to interact with WIPP ventilation-monitoring systems through the sitewide central monitoring system. Data (e.g., air quantity and differential pressure) can be continuously collected from the underground ventilation remote-monitoring and control system and from the mine's weather stations (psychrometric data). Furthermore, WIPPVENT incorporates regulator characteristic curves specific to the site. The program utilizes this data to create and continuously update a real-time ventilation model. This paper discusses the design, the key features and the interactive capabilities of WIPPVENT.

Jan 1, 1997

Hang ventilating air curtains so that they can be installed, moved, opened and closed more easily than curtains that are spadded or nailed in place. Approach Low-leakage plastic curtains fitted with grommets along the top were threaded onto a steel cable which is suspended from roof bolt plates. The system was tested in two mines. How It Works The curtains are threaded onto a steel cable which is suspended from roof bolt plates by S-shaped hooks. See Figure 1. The outby end of the cable is reeled off a hand operated winch; the inby end of the cable is anchored to a roof bolt plate by means of a cable grip and an S-shaped hook. To install the curtains the following procedure is used. First, the winch is located at least 5 feet outby the last open cross-cut. The base of the winch can be secured to the mine roof with short roof bolts, only about a foot long.

Jan 1, 1978

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

Provide means for rapidly re-establishing ventilation control in metal mines after blasting, for emergency applications, and for routine temporary use. Approach Two quickly-installed, parachute-like stoppings have been developed and tested by the Bureau's Pittsburgh Mining and Safety Research Center. How the Parachute Stopping Works The parachute stopping can be fastened to an existing anchor point, opened, and effectively block the air flow, in less than two minutes. Because the parachute stopping tends to be self-scaling, its performance is generally better than that of conventional fabric stopping. However, the periphery of the parachute stopping must be longer than the periphery of the mine opening, Figure 1 shows the parachute stopping deployed in a mine entry. To reduce leakage during routine use, the cloth at the periphery of the parachute stopping can be adjusted and then anchored at several points as necessary. This extra adjustment can also be done after the initial installation during mine rescue or mine recovery.

Jan 1, 1977

Improve the effectiveness of face ventilation systems in coal mines by minimizing leakage around line and check curtains. Approach In-mine surveys were conducted to determine current curtain construction techniques, their effectiveness and associated costs. In addition, performance characteristics of extensible curtains were evaluated. A total of 77 conventional curtains in 10 mines was examined for 12 important characteristics. Extensible curtains were erected in a full-scale model and examined for operational difficulties, effects of leakage, and air pressure. Survey Results The underground mine study identified four categories of face brattice construction ranging from simple to complex: 1. Simple suspension of the curtain from roof bolts with the bottom edge lying on floor. 2. Spadding of the curtain to the roof on about 12-inch centers and stabilization of the bottom edge with wood or rock. 3. Use of vertical props and spads with a base board for support on the bottom. 4. Use of vertical props with caps and bottom boards plus horizontal brattice support boards.

Jan 1, 1984

By T. G. Carnahan

The Bureau of Mines investigated a flotation-nitric acid leach procedure as part of the goal to maximize minerals and metals recovered from primary and secondary domestic resources. Studies were conducted on an ore that contained carbon-bearing and sulfide mineralization that rendered a portion of the ore refractory (resistant) to conventional leaching technology. The procedure investigated for treating the ore consisted of the following: (1) separation by flotation of the carbonaceous and sulfidic components from the ore, (2) leaching the flotation concentrate with nitric acid at 100° to 110° C, (3) leaching the flotation tailings with sulfuric acid, and (4) processing the combined leached slurries in a conventional manner to recover yellow cake. In step 2, HN03 is converted to gaseous products from which it is regenerated by reacting these products with air and water for further leaching. An overall uranium extraction of 96 pct was achieved by this procedure.

Jan 1, 1979