Search Documents

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By G. K. Burgess

G. K. BURGESS* and R. W. WOODWARD,? Washington, D. C.-From a metallurgical standpoint, there are several ways in which a reduction of the tin consumed in commercial non-ferrous and white-metal alloys can be effected. First, a reduction of the tin, content of the alloy; second, substitution of part or all of the tin content by some other metal; third, a substitution of a different type of alloy, which in some cases also involves a change in mechanical design. The Bureau of Standards has been studying these methods of conservation for tin alloys, particularly in regard to babbitts and bearing metals, bronzes, and solders. Much of the information secured by the Bureau was obtained from answers to questionnaires sent to manufacturers and users of these materials, so that, in general, any of the following suggestions or recommendations can be considered as being practical and as having already been thoroughly tried. Bearing Metals There is no question that the tin content of nearly all bearing metals can be reduced to some extent, and in some cases actually eliminated

Jan 12, 1918

By Edmund Newton

THE steel industry of the United States has depended in the past almost wholly upon imports for its supplies of manganese. Many of the important domestic sources yield ores leaner in their natural condition than the foreign ores the steel industry has been accustomed to use. To make them available, therefore, either' the ores must be concentrated or the practice of the steel industry modified. Roughly 25,000 T. annually of high-grade manganese ores are used for dry batteries, for chemical purposes, and in other ways; while approximately 750,000 T. are required for making steel. By present practice, every ton of steel takes an average of about 14 lb. (1.8 kg.) of metallic manganese. This is generally added to the steel in the form of an alloy, the standard alloys being the 80-per cent. ferro-manganese and the 20-per cent. spiegeleisen. During the year 1917 286,000 T. of ferromanganese and 193,291 T. of spiegeleisen were made in this country, the former largely from imported ores; and 45,381 T.

Jan 2, 1919

By D. V. Professor Keller

The production of premium coal-based fuels (<3% ash) and ultra clean coals (<1% ash) using the process of selective agglomeration requires proper selection of raw coal, rough preparation procedures, milling equipment, product coal size distribution, water purity, agglomerants, agglomeration equipment and operational procedures. Each of the variables can contribute a small fraction to the impurity load in the product coal or limit the ability of the process to separate mineral matter-free coal. Each of the variables and their importance will be examined from data produced at the bench by batch and continuous agglomeratons as well as the results from pilot plant and tonnage production units. The results are discussed which have indicated that some standard commercial coals can be produced with ash contents as low as 0.2 % ash (batch/bench) and several tonnage lots of 0.6% ash in as 200 lb/hr pilot plant. In most cases iron pyrite released from the coal matrix and with proper pH control is rejected from the product coal agglomerates.

Jan 1, 1995

Mine geologists have access to an economic mineral deposit, production parameters and secure exploitation title. They are well placed to understand ore formation and should contribute to the effective exploration of company mine property. Application of their special skills has been curbed by pre-occupation with production duties and by company re-engineering, including staff reductions. Contributions to exploration have been diminished and personal development inhibited. Modified management is required. Participation in mineral system studies and in exploration research comprise part of the basis for the re-emergence of mine geologists on the exploration scene. Changes in investment strategies in the minerals industry may create new employment opportunities. With regard to estimation of resources and reserves, the competence of practitioners who are incapable of disclosing their methods in transparent terms is under question. Ethical standards are also under public scrutiny because of some notable malpractice. Independent auditing may hecome more intrusive. While understandable in a market context, it reflects poorly on the profession. More substantial effort in public communications can improve the credihility ofthe industry and equip practising mine ceolouists for snider responsihility.

Jan 1, 1997

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

2, Survey of Representative Group of Metal and Non-mental Mines Before proceeding to develop and analyze Emergency Escape System Guidelines, it was necessary to obtain a broad range of information, including both fact and opinion. Although there were many areas to consider, the surveys had three primary goals 1. To determine the current state of underground escapeway planning and execution in American, metal and non-metal mines. 2. To determine, for a wide range of mining conditions, what difficulties can be encountered in complying with present and proposed escapeway regulatory standards. 3. To determine what improvements could be made and what equipment and technology was available to aid in implementing these improvements. To accomplish these goals, three major surveys were undertaken¬ 1. Survey of MESA and State Mining officials, discussed in Section 2. 1. 2. Survey of representative U S metal and non-metal mines, discussed in Section 2. 2. 3. Survey of manufacturers supplying equipment, primarily hoisting, suitable for use in escape systems, the product information which was obtained is discussed in Section 7.

Jan 1, 1976

By K. D. A. Whaley

The Captain North Extension deposit consists of five sulfide lenses hosted in cherty and chloritic metasediment that is bounded by quartz-eye rhyolite and laminated rhyolite. Lens 2 consists of sphalerite and galena with silver-rich tetrahedrite in chert. Lens 3 contains massive pyrite, with chalcopyrite and minor gold, gradational to minor pyrite in a chloritic metasediment. The other lenses are unexplored. The sulfides occur as beds, fracture infills, and disseminated grains. Reserves are estimated at 207 555 tonnes grading 7.380/0 Zn, 2.76% Pb, and 91.81 g/t Ag. The deposit is isoclinally folded, dips steeply west, plunges 50 degrees south, and is faulted out to the north, where drag folding has reversed the plunge. Minor cross-faults contain talc and sericite. High sphalerite but low pyrite abundances result in poor responses to standard electromagnetic techniques. Lens 3, which contains more pyrite than Lens 2, responds better to induced polarization and allows detection. Geochemical anomalies are found in a nearby swamp and stream, but an impervious till cover inhibits the development of soil anomalies.

Jan 1, 1992

By John J. Howard

WE are approaching the depletion of our principal source of iron ore-the Great Lakes deposits, which have provided 85% of the nation&apos;s requirements for the past fifty years. This situation presents a threat to our standard of living and our position as a world power. Fortunately, in the Great Lakes region there are still tremendous quantities of potential iron ore in the form of the low iron, high silica rock called taconite. The economical extraction of iron from taconite will insure our future steel supply if no new deposits available to the United States even in time of war are discovered. In the new process presented here, the iron is reduced directly by a simple method and then separated from the silica. The product is "feed," not to the blast furnace, but to the steel plant. This process requires very much less plant, less physical and chemical treatment, and less fuel and auxiliary materials than the conventional ore concentration-blast furnace method. In my opinion, this new, fundamentally different approach offers a better hope for the solution of the iron ore problem.

Jan 5, 1950

By J. J. Lewis

In the mid-1970&apos;s a major new prospect was proved in a previously unworked region of North East Leicester- shire, United Kingdom. Preliminary estimates from borehole information showed over 500 million tonnes of recoverable reserves. A special Planning Team was set up, to co-ordinate the work for the two local Areas, South Nottinghamshire and South Midlands (management of production of the UK National Coal Board is organised in twelve such Areas). The team was led by one of the authors as Deputy Director, Mining, North East Leicestershire Prospect (NELP). The remit imposed by the National Coal Board was to analyse the possible options of number, location and eventual rates of output of shaft or drift access; to select a recommended alternative in the light of geological, mining, topographical and environmental considerations; and prepare submissions in accordance with standard Board practice on major projects - such submissions including detailed engineering design, financial appraisal, and full risk assessment. To assist the Planning Team, surface and underground consult- ant engineers were appointed to prepare feasibility studies of specific civil and engineering problems.

Jan 1, 1979

By P. E. Richardson, N. P. Finkelstein, Z. Chen

The large band gap and insulating properties of sphalerite have limited the application of standard electrochemical techniques for studying its reactions with flotation reagents. This problem has been overcome by developing electrodes that rely on the surface conductance produced when sphalerite is activated with copper or other heavy metals. A brief exposure of the mineral in copper sulfate solutions results in electrodes that exhibit significant electrochemical activity characteristic of copper sulfides. Voltammetry studies conducted on sphalerite activated in 10-4 M CuS04, solutions at pH 4.6 provide information on both the amount and the nature of the activation product(s). It is shown that copper activation is strongly dependent on the electrochemical potential applied during activation. Activation at potentials increasingly negative of the rest potential causes a progressive increase in the amount of copper on the surface; activation at potentials positive of the rest potential decreases the amount of copper on the surface. The results indicate that both the kinetics of copper uptake and, possibly, the chemical composition (stoichiometry) of the activation product are controlled by the electrochemical potential.

Jan 1, 1995

By Min Xiaobo

As for treatment of zinc-containing wastewater, traditional SRB (Sulfate Reducing Bacteria) process was used, however, there exist two defects, like toxicity of heavy metal ions and high effluent COD (Chemical Oxygen Demand) value. In this study, a new technique, called ISIS process (Immobilized SRB sludge beads with Inner cohesive carbon Source), in which SRB sludge is embedded in carrier of PVA (Polyvinyl Alcohol) with carbon source that adsorbed on certain material, is put forward for the first time to overcome the two defects existing in traditional SRB process. Furthermore, it has been shown that compared to traditional SRB process, ISIS process increases average zinc removal rate up 30%, average sulfate reduction rate up20%, and decrease average effluent COD value to meet discharge standards. If activated carbon is selected for carbon source adsorption and fixing material, and PVA for immobilization material, the zinc removal rate can reach above 98% under the conditions of 35 and pH 6. Meanwhile, the mechanism of zinc removal has been determinated according to the results from SEM (Scanning Electronic Microscope) and XRD (X-Ray Diffraction).

Jan 1, 2006

Use controlled blasting techniques to reduce blast-produced overbreak damage to underground mine ribs and back for both safer working conditions and improvements in productivity. The Problem Blasting is used in metal and non-metal underground mine slopes, drifts and crosscuts to fracture rock to be excavated and further processed. Standard blasting also produces fractures in the rock beyond the desired excavation area. This is sometimes evident by rough surfaces, undercutting and other signs of excessive damage. This damage contributes to rockfalls in the mines, a major cause of injuries and fatalities, and equipment damage. A variety of controlled blasting techniques has been developed for civil engineering projects where long-term stability is essential. For several reasons, these methods arc not widely used in mining. For example, these methods incur additional costs and time; there is little need to maintain stable openings over long periods of lime; and there is the perception (hat corrective remedial techniques, such as rock bolting, are more practical. Basically the benefits of these methods are not demonstrably clear for application in underground mines.

Jan 1, 1991

By Robert A. Jankowski, Ellsworth R. Spencer, Jay F. Colinet

Longwall mining is the most productive method of under- ground coal mining in the United States (US.), and record levels of production have been reached in recent years. These ever-improving production levels have the potential to generate significantly higher quantities of respirable dust. Consequently, the longwall industry continues to struggle with controlling dust liberation and maintaining compliance with the federally-mandated respirable dust standard. In response, longwall operators have in- creased the application of primary dust controls, airflow and water flow, in an effort to improve respirable dust control and reduce worker exposure. Pittsburgh Research Center (PRC) personnel conducted dust surveys at 13 longwalls operating throughout the U.S. and collected information to: identify current operating practices on these longwalls, identify the types of dust controls in use, document the levels at which these controls are being applied, and measure the respirable dust levels present. This data was analyzed to quantify the dust levels generated by the major sources on the longwall section and to evaluate the relative effectiveness of the control technologies in use.

Jan 1, 1997

By Richard D. Harvey

Relative quantitative analyses of certain mineralogical and textural properties of carbonate rocks were made with an image analysis computer. The instrument, referred to by its manufacturer as a Quantimet; consists of a petrographic microscope, a television camera and monitor, a detector, an electronic computer, and a read-out meter. Measurements were made on polished and etched specimens, standard thin sections, and on scanning electron micrographs of carbonate rocks. Critical to the success of the analysis is the preparation of the specimen in such a way that good optical contrast is obtained between the various petrographic components. The dolomite content, the pore volume, pore boundary projection, and pore size distribution of high-purity carbonate rocks were measured by image analysis methods. The frequency and size distribution of void inclusions in dolomites were determined by image analysis of scanning electron micrographs of cleaved surfaces. Image analysis methods permit rapid and quantitative assessment of various microscopic properties. The results are of reasonable accuracy and certainly are relative quantities that may be used to characterize carbonate rock materials.

Jan 1, 1972

Develop a cost-effective diesel aerosol sampler that can be used by industry and regulatory agencies to determine the diesel exhaust aerosol concentration in mine atmospheres. The sampler must be easy to use, wearable by mine personnel, compatible with current personal sampling protocols, and inexpensive. Approach The University of Minnesota (University) and the U.S. Bureau of Mines (USBM) have developed and tested a prototype diesel exhaust aerosol sampler. The sampler, however, was complicated and expensive to fabricate. Consequently, the USBM redesigned the sampler to simplify both manufacturing and use, and the sampler was evaluated to ensure equivalency with the prototype. Background The National Institute for Occupational Safety and Health (NIOSH) has recommended that "whole diesel exhaust be regarded as a &apos;potential occupational carcinogen,&apos; as defined in the Cancer Policy of the Occupational Safety and Health Administration." In addition, the U.S. Mina Safety and Health Administration (MSHA) has been directed by an advisory committee to establish a diesel exhaust aerosol standard and regulations to minimize exposure to diesel pollutants in underground coal mines.

Jan 1, 1992

By B. M. Andreas

PRIOR to 1934 all haulage of ore and stripping on the Mesabi Range was by rail. Early rail systems had small narrow-gage locomotives with correspondingly small dump cars. These trains were replaced with larger standard gage rail systems powered by steam locomotives ranging up to 224 tons in weight, which have in turn been replaced by diesel electric locomotives. Along with this development cars have been increased to 30-cu yd capacity. Improvement of cars includes alloy steel construction for lower over-all weight and use of roller bearings to decrease rolling resistance. Despite all of these developments, the total material hauled by rail on the Mesabi Range has decreased every year. Yet, this is no reason to believe that rail haulage is becoming obsolete. Its adaptation to small mine operation has become impractical, but in large mines where normal railroad grades are possible or where hauls to plants or dumps are long, rail haulage is still one of the most economical methods of transporting large quantities of material.

Jan 1, 1954

By M. E. Volin, F. H. Erbisch, G. M. Wenberg

Bacterial leaching of copper and uranium is practiced under acidic conditions in environments furnishing sulfur and iron. However, many mineral deposits do not have these conditions; the chalcocite and native copper deposits in Michigan&apos;s Upper Peninsula are examples. Species of bacteria and fungi isolated previously from samples taken at the White Pine Copper Co. tailings pond and mine, were screened for solubilization of copper from chalcocite ore and flotation concentrate and from native copper jig concentrate. Certain Penicillium species solubilized significant amounts of copper under neutral to slightly acidic conditions in a carbon and nitrogen-enriched medium. Leaching apparently was accomplished by release of metabolites which chelated with the copper. The copper yield was highly dependent upon the medium composition and the concentration of copper in the source material. The standardized procedures which were developed in an attempt to maximize copper yield in leaching times of three to five days are described. This preliminary research indicates a biological leaching process for copper which is different from those in use, but whether it can be applied economically remains to be determined.

Jan 1, 1972

Improve transmission of data from an underground mine monitoring system to a remote, mass-data storage system. Background Instrumentation systems in underground mines must operate under environmental extremes of dust and humidity, local electromagnetic/radio frequency (EM/RF) interference fields, and potentially explosive atmospheres. During a recent roof-bolt study performed by the Bureau of Mines, it was necessary to transmit a large quantity of data to a data storage system. Conventional wire cable transmission presented several limitations which often required special electrical isolation or physical protection. Because conventional wire cable presented certain problems, the Bureau of Mines investigated alternative means of data transmission. The research investigation led to the selection of fiber optic cable for data transmission applications. The fiber optic method of data transmission offers several advantages: ? Since the transmission medium consists of light waves, it is safe to use in gassy mines. Where applicable, MSHA permissibility standards for peripheral devices must be met. ? It is lightweight and rugged. ? It can operate up to 131000 feet (4km) without repeaters and without EM/RF field interference.

Jan 1, 1986

The environmental and social responsibilities of the mining industry have long been recognized by the industry itself, but during the past decade it became one of the main targets for the more radical members of the community. This came as something of a shock to an industry which had always considered that it had acted responsibly within the standards of the day. As far back as early 1968, the Australian Min- ing Industry Council (AMIC) was clipping from newspapers the odd letter written by environmen- talists and critics of mining activities. In those days every such letter was carefully studied to ensure that AMIC, if not having the answers, at least had an understanding of the types of argu- ments then starting to be used against mining activity and in favour of environmental preserva- tion. Within 18 months, the infrequent letter to the editor had become a flood of such letters and feature articles, and the environmentalists&apos; attack on mining activities had been launched in all its Vehemence.

Jan 1, 1978