Search Documents

By J. R. Donald

Electric arc furnace (EAF) dust, which can be considered as a by-product of the steel recycling process, contains significant quantities of recoverable zinc and iron, as well as hazardous elements such as cadmium, lead and chromium, which can be leached by ground water. The zinc in the EAF dust is found almost entirely in the form of either zinc oxide or zinc ferrite, the latter accounting for 20 to 50 percent of the total zinc. It is important that an efficient process be developed which renders the dust inert, while reclaiming the valuable metals to off-set processing costs. During the conventional carbothermic reduction processes, iron is formed, and this iron can participate in the reduction of the zinc oxide in zinc ferrite. In the present work, the reduction of the zinc oxide in zinc ferrite by iron according to the following reaction: ZnO-Fe2O3(s,s) + 2 Fe(s) = Zn(g) + 4 FeO(s) was studied in an argon atmosphere using a thennogravimetric technique. First, a thermodynamic analysis was performed using the F*A*C*T computational system. Then, the effects of briquette aspect ratio (lid), temperature, zinc ferrite particle size, amount of iron added, as well as additions such as lime, sodium chloride, and calcium fluoride were investigated. It was found that, initially, the reaction was chemically controlled with an activation energy of 178.1 kJ/mol. Then, after a product layer had formed on the outer surface of the briquette, the reaction was restricted by the diffusion of zinc gas away from the reaction interface. The parabolic rate law was fitted to the experimental data, and the parabolic rate constant was found to be: = -6.2275 + 0.0054 T (K)

Jan 1, 1995

By Zibo An, Yong Hu, Hao Zhang, Hong Cao, Jun Xue, Zhen Luo

Phosphogypsum (PG) is a by-product of solid waste produced by the phosphate chemical industry. Owing to large emissions and massive storage issues, it causes a potential threat to our environment. Hereby, a method based on the precipitation and crystallization properties of calcium phosphate-magnesium ammonium phosphate (CP-MAP) followed by its adsorption on active solid waste powder is used as the main principle to treat PG harmlessly. The treatment process and its influencing factors for orthogonal experiments along with the associated environmental safety have been studied in detail. The results showed that this method could simultaneously remove soluble phosphorus and soluble fluorine from PG. When ACP, FA, HBM, and Ur were added to PG at a dosage of 3%, 13.5%, 0.04%, and 0.04%, respectively, the residual phosphate and fluoride contents was 0.061 mg/L and 0.856 mg/L respectively in the PG leaching solution. Compared to state-of-the-art approaches, this method exhibited higher efficiency in removing phosphate and fluoride. Most importantly, this method does not cause any secondary pollution in the process, thereby showing a novel application in large-scale industrial treatment.

Aug 29, 2022

By Kenneth N. Han

Ammonia has been found to be an effective leaching reagent for gold, silver and platinum group metals in the presence of appropriate oxidants. Electrochemical and kinetic aspects of the dissolution of elemental gold in ammoniacal solutions have been investigated. The cathodic reaction of aurous di-ammine on the gold cathode has been investigated first. From this investigation, the standard electro-potential of the cathodic reaction .and hence. the Gibbs free energy of formation of the aurous di-ammine were established. The solubility of gold in ammoniacal solutions was also examined in relation to ammonia concentration, temperature and concentration of various oxidants. The anodic reaction of the gold disk in ammonia? in the presence? of various oxidants including oxygen, ozon, hypochlorite, hydrogen peroxide, cupric and cobaltic ammine, and iodine was also examined and the results have been discussed. Excellent dissolution yielding of gold and many other metals, typically better than 95% recovery in 1'-2 'hours of leaching at a temperature ranging 80°C to 190°C has been observed. Test results of the dissolution of gold from elemental state as well as other sources including sulfidic ores and scrap are presented.

Jan 1, 1998

By Marcel Laflamme, Sebastián Ibarra‑Gutiérrez

Improvement on controlling the stope limits has enabled the assessment of technical performance in several underground mining operations. Technical performance, integrated to stope geotechnical and geomorphological parameters, constitutes the basis which guides mining engineers in the Mineral Reserves Estimation process. Moreover, there are established definitions to report this information in Canada, incorporated in NI 43–101, which stipulates that “A Mineral Reserve includes diluting materials and allowances for losses that may occur when the material is mined” [1]. However, some loopholes have been identified regarding practical standards followed to specify the way to include and report ore losses when the lost material was blasted and must be left behind unrecovered inside the stope. In fact, general efforts to estimate and quantify the negative effects of operational ore losses only consider under-break ore loss. However, mining engineers frequently confront situations requesting the anticipated closure of a stope. Therefore, reconciliation process should reflect the amount of unrecovered Mineral Reserve. This work presents a discussion of possible practices to integrate adequately operational ore losses consisting of blasted but not recovered material and focuses on how different approaches regarding the material constitution could severely affect the stope technical performance interpretation.

Aug 9, 2021

By J. Ellis Thomson

For many years the value of qualitative microscopic investigation has been recognized in both of the fields of pure and applied science. In particular, its aid has been invoked in the determination of rock specimens in thin section, and some at least of the interrelations of minerals present in any one section have been observed and, to a limited extent, applied for the solution of different problems. During the past decade this form of research has also been diverted to the determination of ore minerals in polished section, with some observation of their structural relations. Microscopic research of a quantitative character, on the other hand, while started nearly one hundred years ago, has found but a limited application in petrography and has scarcely been used at all in the more modern science of mineragraphy. This is very largely due to the methods employed, since most of them consumed too much time and were, in addition, too laborious to encourage many workers in their use. The details of procedure for these earlier methods will be found in another paper by the writer, and will be omitted from this discussion as being of small interest to practical mining men.

Jan 1, 1930

By P. Moran

A promising and increasingly popular tailings management strategy is to place cemented tailings underground as backfill. The placement of cemented tailings results in enhanced geotechnical stability and a purportedly more geochemically stable tailings form with lower leaching potential. Conventional subaerial tailings management can negatively affect water quality if weathering causes acid rock drainage and metal leaching (ARD/ML) to occur, whereas cemented tailings can limit leaching via porosity and permeability reductions and contribute alkalinity to limit the potential for ARD/ML. Cemented tailings backfill appears to be better, but how can this advantage be proven? Currently, cemented tailings backfill is utilized at mining operations internationally, but there is limited guidance on performing geochemical characterization and associated evaluation of the potential impacts to water quality. As a result, various approaches to simulating the leaching behavior of cemented backfill have been utilized, including some methods that are unlikely to represent weathering under site-relevant conditions. American Society for Testing and Materials (ASTM) Standard Test Method C1308-08 is a diffusion testing method initially developed to assess constituent release rates from solid nuclear waste forms. ASTM C1308-08 uses intact cylinders that more closely represent actual backfill than methods that require crushing or size reduction. It is widely believed that leaching from actual cemented tailings is controlled by diffusion through small pores that exhibit limited exposed surface area, making diffusion testing particularly applicable to cemented tailings placement.

Feb 27, 2013

By Jeane Hull

Jan 1, 2009

By Vladimir Nikolić, Alex Doll

The Bond ball mill grindability test is one of the most common metrics used in the mining industry for ore hardness measurements. The test is an important part of the Bond work index methodology for designing and measuring the efficiency of mineral grinding circuits. In spite of being called “Bond’s Law,” the work index equations are not a law of nature; but rather an empirically measured regression of a large data set collected by the Allis- Chalmers corporation in the period between 1930 and 1952. As a regression, it is valid within a specific “calibration space,” and great care is required when deviating the test procedures or observing results that are outside of that calibration space. This paper is a collected summary of other works by the Authors that describe feed sizes, product sizes, quality control checks, and other information about interpreting the test and using its results. Examples of adjustments that are sometimes required when using the test are: changing the test product (P80), and coping with a feed that is too fine to apply the “proper” feed preparation steps (such as is sometimes observed from HPGR or SAGDesign product testing). Related metrics, like the Morrell Mib value and Levin B value will be discussed, along with recommendations for their use on design projects. The intended audience is any user of laboratory work index test data.

Feb 1, 2024

By O. E. Omotoso

This study is part of an ongoing investigation to understand the mechanism of stabilization/solidification of hazardous chromium wastes in ordinary Portland cement (OPC). Tricalcium silicate (C3S*),a major component of OPC is mixed with reagent grade Cr(lll) and Cr(VI) solutions, to simulate complex cementiCr waste systems. Scanning electron microscopy (SEM) and energy disperse spectrometry (EDS) were employed to provide microstructural and chemical information. Transmission electron microscopy (TEMlEDS), apart from complimenting the SEM, was used to probe the distribution of Cr in the hydration products of C3S and to provide crystallographic information. 29Si MAS NMR (magic angle spinning - nuclear magnetic resonance) Was used to characterize the influence of Cr on the hydrated silicate structure.

Jan 1, 1995

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By Deborah A. McCombe

"There are a number of important dates that must be disclosed when a Qualified Person (QP) is preparing a technical report for securities purposes. The dates are discussed in NI43-101 and the Form of the Technical Report, NI43-101F1. •,Effective date of the technical report •,Possible revision date of the report •,Effective date of mineral resources and mineral reserves •,Date of the personal inspection (site visit) •,Signature date of the date report (execution date) •,Date of the certificate of the QP •,Date of the consent of the QP The effective date of the report is basically the cut-off date for the information that is included in the technical report. The effective date should be close to the signature date. If there is too long a period between these dates, the QP runs the risk of new material information becoming available and then the technical report would no longer be current. The effective date is disclosed on the title page of the report and on the signature page. If a technical report needs to be revised to correct problems or disclosure deficiencies identified by the regulators, the QP will normally need to include a revision date on the title page of the report to distinguish the revised version from the original version. In these circumstances, the regulators will request that the original date of the report remain on the title page and the revised date will be below it. When a technical report must be revised, the QP must resign and date the signature page of the report and provide a new certificate and consent."

Jan 1, 2003

By A. Vidyadhar

Printed circuit boards (PCBs) constitute a majorpart of electrical and electronic equipment containing valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, Pb, etc. The concentration of base and precious metals in PCBs is observed to be several times more than those in their respective ores. Therefore, the recycling of PCBs is necessary to recover the valuable materials. However, the ultrafine particles pose a big challenge. Removal of them is suggested prior to processing by flotation. Froth flotation is observed to be a promising technique for rejecting the plastics from the comminution product. In the present work, enrichment of ground 1.0 mm PCB powder was investigated through flotation route by varying the operating variables such as frother dosage, pulp density, air flow rate and rotational speed of the impeller. The liberation studies indicate that excellent liberation of metal values is achieved from the non-metallic constituents at -1.0 mm size and below. The particulate system is quite rich in metal value with about 23% total metal content. The non-metallic constituents such as plastics are observed to possess strong hydrophobicity while the metal particles in the pulverized mass are hydrophilic in nature. Froth flotation kinetics is studied in depth with a view to facilitate high rejection of plastics and identify optimum operating conditions for the same. A number of experiments are performed to establish the influence of the operating variables on flotation performance. The conditions for achieving higher yield of the metal-rich fraction with respect to a specified grade are discussed in the light of the experimental results. It is found that the requirement of reagents is negligible which could be a very important factor from the commercial stand point. Single-stage flotation increases the metal content from 23% to over 32% with a mass yield of around 75% and over 90% recovery of metal values. 32% of the materials in the feed could be effectively rejected in the float fraction losing less than 4% metal values. The dependence of kinetics on the process variables is also discussed. It was concluded that a high rotor speed helps in efficiently rejecting the plastics. Frother should be added to help stabilize the froth and enhance the kinetics. A moderate air flow is required while pulp density must be kept low for efficient pre-concentration. It is established that the entire -1.0 mm comminution product could be treated by flotation for generating a pre-concentrate. Keywords: printed circuit boards, recycling, froth flotation, kinetics, recovery

Sep 1, 2012

By B. J. Moore

This Bureau of Mines publication reviews U.S. helium resources as of January 1, 1973. These resources, estimated to be 693.7 billion cubic feet, are broken down into four classifications, as follows: helium in storage, 34.9 billion cubic feet; helium in measured helium-rich natural gas reserves, 119.5 billion cubic feet; helium in measured helium-lean natural gas reserves, 62.8 billion cubic feet; and helium in indicated or undiscovered natural gas resources, 476.5 billion cubic feet. The helium in undiscovered natural gas is considered a national resource; however, this gas may not be discovered depending on many factors beyond the scope of this paper, and most of the helium in natural gas will be dissipated as the gas is consumed for fuel and other purposes.

Jan 1, 1976

By E. Essadiqi, P. Poruks, D. Boyd, D. Emadi, I. Yakubtsov, T. Turi

This paper reviews the results of an extensive study of microstructures and mechanical properties in bainitic linepipe steels. The research was carried out as a collaborative project between Queen's, Stelco and CANMET. Basic studies of phase transformations and mechanical properties in these steels established important relationships between processing schedule and microstructure evolution, and between final microstructure and mechanical properties. The best combination of strength and toughness properties is obtained with a microstructure comprising a matrix of intragranularly-nucleated bainite (`acicular ferrite - AF') and small (~ 0.5 µm) dispersed particles of martensite (`M/A'). We describe this as a dual-phase AF+M/A microstructure. An experimental study on 15-mm thick plate determined the window of steel composition and processing parameters which gives the dual phase AF+M/A microstructure. The minimum strength and toughness properties for Grade 621 (X90) linepipe steel can be achieved by either a lean steel composition (0.04C-1.77Mn-0.04Cr¬0.32Mo-0.31Ni-0.29Cu-0.08Nb) with extreme processing parameters, or by a higher alloy composition (0.04C-2.07Mn-0.50Cr-0.51Mo-0.04Nb) with a more industrially realistic processing schedule. It is proposed how this approach could be extended to obtain higher strength linepipe grades.

Jan 1, 2005

By J. Christophe Niyonzima, Ekata Emmanuel Edo, Sayaf Mustafa, Liqun Luo

Iron and manganese both are important ferrous metals, and they usually need to be extracted separately for better usage. Ferromanganese ore from the Yunnan Province of China was investigated by subjecting it to reduction roasting, leaching, magnetic separation, hydrometallurgical separation process, X-ray diffraction (XRD), electron probe micro-analysis (EPMA) and scanning electron microscopy/energy-dispersive spectroscopy (SEM-EDS). It is noted that the ferromanganese ore contains valuable components or elements of 21.41 wt%Fe2O3 and 19.88 wt%MnO, which are 14.99% and 15.40% of the total of Fe and Mn, respectively, with a large amount of impurities comprising 33.00 wt% SiO2, 9.81%wt%Al2O3, etc. After roasting, microscopic examination showed the presence of haematite, magnetite, pyrolusite, psilomelane, hollandite, marcasite, pyrite, limonite, braunite and manganite, while XRD analysis showed that the magnetite content increases with the increase in roasting temperature, reflecting the increase in conversion of haematite to magnetite. Based on EPMAand SEM-EDS analysis, it was shown that the haematite and magnetite interface were the main Fe-bearing minerals; however, the dissemination of the two minerals, that is, haematite andmagnetite with the coexistence of Fe- and Mn-bearing minerals, will result in difficulty in effective separation of Fe and Mn. The effective roasting temperature and roasting time were 800 °C and 60 min, respectively, to avoid the formation of a composite oxide of MnxFe3-xO4 beyond 800 °C. The Fe recovery via roasting and magnetic separation only was 66.56%, whereas a combination of magnetic separation which ensued after the leaching process showed a recovery of 80.08% and 59.95% of Fe and Mn, respectively.

Mar 26, 2021

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By Earl L. Phillips

The Bureau of Mines conducted laboratory tests on samples of pozzolaniccement concrete to develop a low- strength backfill . Results show that support costs can be lowered by replacing a portion of the portland cement in mine backfill with pozzolan ( fly ash ) and lime . Unconfined compression tests on various ratios of fly ash to cement in 84 samples produced compressivestrength curves that can be used to estimate the best backfill mix for any mine .

Jan 1, 1964

By Vinícius Resende Domingues, André Pacheco de Assis, Bernardo Cascão Pires e Albuquerque

"The increasing demand for underground works in urban centers, and in particular the need to build undercrossing tunnels, requires constant evolution in building techniques in order to achieve success and safety. In the case of Brasilia, capital of Brazil, in order to preserve an important avenue (Eixo Monumental), where are located many historical monuments, the construction of a tunnel was envisioned as an option to interconnect the National Stadium (on one side of the avenue) to the Convention Center Ulysses Guimarães (on the other side). The excavation design is comprised of a coverage smaller than one diameter, height of 7.5 m, width of 9.0 m and length of 25 m. In order to enable a negligible influence on the avenue’s usage, the structure is designed as a portico system composed of pipe canopy. In this context, this study presents the portico analytical solution computed with the aid of the software Mathematica and a numerical solution using the software ABAQUS. INTRODUCTION Undercrossing tunnels are increasingly common in urban centers as alternative roads or as access to underground works of large dimensions (stations and parking lots). The geomechanical conditions of the soil mass, not always favorable, and the low distance between tunnel’s ceiling and the surface require intense treatment of the soil massif and execution of a rigid support system. The importance of the road just above the undercrossing tunnel emphasizes the need for a highly competent monitoring system because existing structures require minimum allowable displacement and do not allow the interruption of traffic. The soils that are excavated for the construction of undercrossing tunnels are composed, in most cases, of layers of fill and / or soft soil or weak rock, showing stability problems when subjected to tunneling operations. The combination of low coverage and week ground is solved by soil improvement techniques and strengthening of the excavated cross-section with further advance with the so-called New Austrian Tunneling Method (NATM). Another option is to build structural frames that support the surface. In this research, and based on the context of a case study, we propose the study of the construction technique comprising a portico structure composed of pipe canopy. For this paper, the technical standards used are the Brazilian ones as the case study refers to this country."

Jan 1, 2016

By Maxwell Adams

Considerable interest has recently been developed in sage-brush oil because of its possible utilization as a flotation agent in the mining industry. A list of some of its physical properties, together with the method used in its extraction, may prove of interest at this time. Something over a year ago, a study of the essential oils in desert plants was begun in the Chemical Laboratory of the University of Nevada. None of the oils so far studied possess properties of special interest to engineers, except the oil of sage, Artemisia tridentata, which has exceptional power as a flotation agent. This plant, known as common sage brush, also called black sage, is widely distributed over the semi-arid West, being found quite generally on most of the dry plains and mountains west of Missouri. The method of extracting the oil followed in these experiments is very simple. The leaves, twigs and small branches are placed in an airtight drum, having a capacity of about 27 cu. ft. Steam is admitted through a number of ,small openings at the bottom of the retort, and the pressure maintained at 20 to 25 lb. per sq. in. for 3 hr. The escape of the steam from the retort is regulated by allowing it to pass through a stop-cock into a condenser. The water in the receiver is drawn off from time to time and the oil, which is insoluble and floats upon the water, is thus collected. At the end of 2 hr. most of the oil has been driven out, though traces continue to come over for a much longer time. By raising the pressure, the time required could probably be shortened and the yield increased, but the lack of laboratory equipment has prevented the carrying out of this experiment. The stock wood, bark and branches contain no oil, the distribution of the oil being limited to the leaves and young shoots. There is a seasonal variation in the amount of oil contained. Samples collected on different dates gave the following amount of oil: May 1, 0.42 per cent.; May 27, 0.6 per cent.; June 30, 0.72 per cent.; Aug. 1, 0.9 per cent.; Sept. 10, 1.0 per cent. The increase appears fairly constant from early spring, when the leaves first appear, until light frosts occur in the autumn. When the plant is air-dried there is some loss of oil, as the following data will show: Two 100-lb. samples were collected at the same time. One was distilled when green; the other was air dried for

Jan 1, 1917

JESSE L. JONES,* Pittsburgh, Pa. (written discussion?).-As the die-casting process is so very different in character from the process of making sand molds, it is often considered that entirely different methods of pouring, gating, venting, etc. should be used. There is really, however, no essential difference in the making of (lie castings and sand castings, and similar methods should be used in each process. In the matter of gating, the metal should be introduced at a central point, as nearly as possible, so that it will have an equal distance to flow from the point of entrance to the most distant points of the mold. This will cause a uniform rate of congealing of the casting and prevent streaks and cold shuts. The venting should be done in such a way that a free exit of the air in the molds can occur. It should be less difficult to take care of the venting of a die-casting mold than to vent an ordinary sand mold. In the case of a sand mold, the venting is left, to a considerable extent, to the judgment of the molder, and it is possible that no two molds will be vented in a similar manner. Further than this, after a vent has been made in a sand mold, it may become clogged by the sand and for this reason be inefficient. There is also quite a variation in the pressure of the metal entering a sand mold, due to varying heights of the pouring gate. In a die-casting mold these factors can be controlled more closely. The vents should be so disposed that the air in the mold compressed by the entrance of the metal may be able to leave the mold at a uniform rate and by exits located symmetrically. These exits are made quite small on molds at first, as they can he easily enlarged if necessary, and they are tapered so that a free flow is guaranteed without danger of the metal spurting out from the die. Uniformity of pressure of the metal as it enters the mold is very important and, as the pressure is mechanically applied, its control is not difficult. It is true that a sand mold has much less of a chilling effect on the metal poured into it than has the die-casting mold, but, outside of this point, there is a great similarity between the die-casting process and the process of making castings in sand folds. It is suggested that much would be gained by regarding these two processes as not essentially different.

Jan 4, 1919