Search Documents

Improve the safety and reduce the cost of longwall entry support. Approach Replace the conventional wood cribbing with stronger, non-rotting and lower cost cribbing made of steel-fiber-reinforced (SFR) concrete. How It Works Conventional concrete can suddenly fail under excessive compression loads, but adding steel fibers to the concrete, before it is mixed with water, changes the failure mode to a gradual and controlled failure characteristic similar to wood. A system for making SFR concrete crib blocks was designed and developed (or use in constructing walls and cribs to support coal mine roofs. The SFR concrete cribbing is stronger and stiffer than wood, and avoids wood's disadvantages of: flammability, deterioration under chemical or bacteriological attack, methane generation, and relatively high cost. Use of SFR concrete also allows freer movement of miners, equipment, and ventilation air, because much less volume of SFR concrete is required than wood for a given amount of support, and because the roof-to-floor closure is greatly reduced by the stiffer supports.

Jan 1, 1981

By Gerald H. Luttrell, Jaisen N. Kohmuench, Michael J. Mankosa

A new separator, known as the Hydrofloat cell, has been developed to overcome limitations of traditional flotation cells in recovering coarse particles. In this process, small air bubbles are introduced into a hindered "teeter" bed of fluidized solids to create light bubble-particle aggregates that can be separated based on differences in density. Laboratory tests conducted with coarse phosphate feeds indicate that the Hydrofloat cell is capable of increasing BPL recoveries by nearly 20% over conventional flotation methods. Based on these encouraging results, a pilot-scale Hydrofloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the plus 35 mesh plant feed can be increased by more than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the plus 16 mesh particles in the Hydrofloat concentrate. This article describes the theoretical basis for the development of the Hydrofloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 1999

By R H. Eric

Surface wave formation induced by a high-strength submerged jet in a bottom blown metallurgical vessels has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations. Experimental results have been discussed in terms of the wave period, wave frequency and wave amplitude with respect to air injection rate and tuyere configuration at a 0.23 m bath height. The results from high speed photography observations displayed the formation of rotating surface waves which circulates within the water model. It was found that the frequency and the amplitude increased with gas injection rate. The wave period for off-centre nozzle orientation was found to be lower than those of the centre configuration. The experimental results also showed that the frequency of a rotating wave increases when the tuyere orientation becomes off-centred . The predicted amplitudes were in very good agreement with the experimental values over a range of gas flowrates between 0.00599m 3/s to 0.01081 m 3/s.

Jan 1, 2000

By P D. Fraser

This paper examines the new water-hydraulic (hydro powered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef, hard-rock South African mines. These include - drill rigs for flat end tunnel development, narrow inclined raises and winzes, large inclines and declines and long hole based developments such as orepasses and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed air powered, hand-held development are generally more cost effective than imported oil electro-hydraulic drill rigs. Furthermore, hydro powered rigs are inherently energy efficient. The benefits of hydropower are discussed and a æcomprehensive development modelÆ is presented which demonstrates that orebodies can be accessed in significantly shorter times. æLocalisedÆ half level hydropower systems are introduced and a range of ancillary equipment available is listed.CITATION:Fraser, P D, 2012. The use of high-pressure, water-hydraulic (hydropower) technology in South African narrow-reef, hard-rock mines, in Proceedings Narrow Vein Mining 2012 , pp 229-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Eaton R. A

The design of most underground mining machines shows little evidence of regard for ergonomic principles and operator comfort. Likewise, efficiency and ease of operation often appear to have been given little consideration in machines where ruggedness and simplicity have tended to dictate the configuration. Improvements in productivity are amongst the benefits to be gained by a different approach to machine design. The paper describes the philosophy and features of a test bed Load-Haul-Dump Vehicle undergoing trials at Mount Isa Mines. This machine is the outcome of a Research and Development Programme conducted by the Department of Mechanical Engineering at the University of Queensland and Mount Isa Mines Limited. The diesel powered test bed features an enclosed, air conditioned cabin, with a suspended operator's control station and electrically operated controls. An electronically controlled hydrostatic transmission incorporating wheel slip control, is another innovation. The performance and operator acceptance of the machine has led to adoption of most of the concepts in a new machine now being put into production.

Jan 1, 1987

Flexibility is the keynote in designing modern exploration drills that and mobility. Add to the flexibility of individual drills the wide range of models, and the man looking for a drill has ample choice today. Weight? Choose from models as light as 50 lb or as heavy as 10,000 lb. Hole capacity? From less than 1 in. for smallest core drills to 20 in. or more for auger types. Transportation? The lightest go by packsack (in fact, that is one trade name) ; others are designed to go by Jeep, truck, on skids or are built on light trailers. Power? Select air power, gasoline or diesel engine, electric motor, or use a power take-off from the vehicle on which the drill is mounted. Drill bits offer almost as much variety as the drilling machines themselves. Many drills are suitable for a variety of uses, and often adapt to several types of bits with ease. Some of the types available are: diamond core, diamond reaming, rotary, auger, shot, and special soil sampling tools.

Oct 1, 1955

By Kostas Fytas, Pierre Bousquet, Bill Evanelou

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidise to produce low pH water. This acid effluent has the potential to mobilise any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pynte is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidises a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2000

To precondition a stope in advance of mining and thus reduce or prevent rock bursts. Approach Drill deep holes from a mine opening in a radial pattern in the vein and load and blast to fracture, the rock prior to production mining How It Works Preconditioning of a sphalerite galena vein in a hard gangue of quartz and quartzite creates a zone of softer rock that fails by displacement rather than violently as an elastic-battle mass. However, the entire area must he analyzed carefully so that the stress transfer does not cause problems in other workings of the mine A typical drill hole pattern and explosive loading is shown in the sketch. Hole diameter is about 4 inches and a down-the-hole, type drill is used. Drilling speed in hard quartzite is about 12 inches per minute High pressure compressed air (250 psi) is used to run the drill. An overhand cut-and-fill stoping area on the 7700 level of Hecla Mining Company's Star Mine in Burke, Idaho was preconditioned above and below the

Jan 1, 1981

Reduce the exposure of diesel vehicle operators to diesel exhaust generated during mucking in deadend drifts. Approach Direct the diesel engine exhaust upward and rearward thereby using the thermal buoyancy of the hot exhaust to form a layer at the roof, above the breathing zone of the vehicle operator. Modifying the Exhaust Outlets Diesel front-end loaders used in nocoal mines to remove blasted ore usually operate in entries open only at one end to cross cut ventilation. These deadend drifts are not usually ventilated with the use of auxiliary fans and vent tubing because of frequent blasting. The existing ventilation, therefore, is usually poor, and a diesel engine operating in such a drift emits exhaust which is not immediately swept away from the operator. On most load machines, the diesel engine's exhaust outlet is located near the floor and directed downward or to the side, so that when the hot exhaust is emitted, it mixes with the mine air as it rises into the vehicle operator's breathing zone. In this way, a uniform concentration of diesel exhaust forms around the operator.

Jan 1, 1983

There is no other effective way for study ing firedamp and coaldust explosions than to produce controlled explosions in a pre-monitor- ed environment - either mine openings kept for the purpose, or special surface galleries. Such explosion testing facilities have been employed historically at Buxton in U.K., with lesser known installations at Bruceton, U.S.A., Tremonia, West Germany, Katowice-Mikolow, Poland and elsewhere. Both firedamp and coal dust explosions are studied. Normally coal dust explosions are initiated by somewhat standardised methane air mixtures, by explosives, or purely by coal dust. Various structures and suppression installations are installed in roadways and galleries prior to explosion to simulate destruction and suppression, and the results of such tests form the basis of suppression installations, especially stone dust barriers and water barriers. Other data collected from these experiments include rev- ersals of explosion waves, pressures and temperatures and duration of explosion waves, analyses of aftergases etc. Other uses of explosion testing galleries include testing of explosives, electrical equipment and frictional . sparking.

Jan 1, 1981

By G. Barbery, P. Dauphin

"In order to obtain reproducible and reproducible results in batch flotation, researchers have tried various approaches, from normalized testing, to modifying existing cells, and even designing new machines. The paper reviews the basic concepts that must be fulfilled in a laboratory flotation machine, and present the FLOTOMATEC design, which results from five years of testing and development. In addition to providing accurate measurements of air flowrate, power consumption, agitation speed, the cell eliminates most operator induced errors. Results of experiments comparing FLOTOMATEC to a conventional cell, as well as reproducibility tests are given. Introduction The use of batch flotation machines in mineral processing research and development is very common. These machines have been used for many years without almost any change in their design, instrumentation or automation. Various authors since Raffinot (1960) have criticized the available designs, especially with respect to the large errors that are introduced by the manual mode of operation. Barbery et al. (1986) have presented a review of the problems involved in laboratory testing in flotation research.Batch laboratory machines should have the following characteristics:"

Jan 1, 1989

By N. Kanarin

A thermodynamic study is reported on the chlorination of Fe(1-x.)O, Fe2O3, Cr2O3, MgO, Mg2SiO4 with chlorine in the presence or the absence of reducing atmospheres. The reactivities of these compounds as well as that of Mg3Si2O5(OH)4 using Cl2+N2, Cl2+air, and Cl2+CO gas mixtures were studied by non isothermal thermogravimetric analysis between 20 and 1000 °C. The same solids were chlorinated in a horizontal experimental set, during two hours between 350 and 1000 °C, in reducing and oxidizing atmospheres: The chlorination products were examined by XRD and SEM, and possible reaction paths were examined. Results indicate that the carbochlorination of these solids was better than their chlorination; Furthermore, the carbochlorination was performed at lower temperatures than those of the chlorination. Finally, the reaction extent was higher in the case of carbo-chlorination of these compounds. Based on these results, a process was suggested for the selective recovery of chromium compounds from the chromite concentrate.

Jan 1, 1995

Prevent the explosion of methane gas or coal dust by replacing air with inert gas inside highwall mine excavations. Approach Use combustion gases as a source of inert gas with low oxygen content to blanket the cutting, head of highwall mining machines. This gas is placed strategically at the collar of the excavation where it enters the hole to replace the mined coal volume. The elimination of oxygen from the hole prevents explosions of gas or dust. How It Works Highwall mining methods arc used when surface mining becomes uneconomical. One method of highwall mining involves use of a horizontal auger to enter the coalbed from a surface mine bench. The coal is mined in a series of horizontal, parallel, and large-diameter holes. Historically, little methane has been associated with auger mining. However, mining technology has extended the reach of auger mining, which can increase the occurrence of methane. Methane explosions at auger mining operations have been increasing. Methane has been the primary fuel source of these ignitions, but coal dust also may have been involved.

Jan 1, 1993

By Nilsson C

Man has always been and will always be part of his environment, in ,a good, bad or indifferent manner. Until quite recently, this environment has been the atmospheric boundary layer above the land masses, and to a limited extent the air-sea interface of the oceans. Since the days when he lived in caves, he has built up a wealth of observations on these two environments,-with ever-increasing scientific precision which unfortunately until quite recently was completely insufficient for modern capabilities of data analysis. Consequently, in a sense, he has left in his wake thousands of years of missed, opportunities for making exact observations and increasing his understanding. The data of the past are lost and he has to be satisfied with what he can assemble from now on when his environ- ment, largely as a result of his actions, is exhibiting more and more rapid variations in time; in other words, time series of observations of phenomena are required, the length of which is critical for most purposes of analysis.

Jan 1, 1970

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995

NEW MEMBERS The following list comprises the names of those persons who became members during the period Jan. 10, 1919, to Feb. 10, 1919. ADAMS, FRANCIS SPEARMAN, Supt., Power Dept., Anaconda Copper Min. Co.; Anaconda Mont. ALDERSON, G. E., Min. & Met. Engr 1317 Sloane Ave., Lakewood, Ohio. BENJOVSKY, T. D., Min. Engr., Cons. & Constr 2045 Vine St., Denver, Colo. BROPHY, OSCAR, Met 1523 S. Broad St., Philadelphia, Pa. BUTTRAM, FRANK, Chief Geol., Fortuna Oil Co., 424 Liberty National Bank Bldg., Oklahoma City, Okla. COCHRAN, R. B., Mine Supt., The Teziutlan Copper Co., Aire Libre Puebla., Mexico. CONNAR, T. C., Civ. & Min. Engr. & Geol.; Chief Engr., Zanesville Coal Co., Zanesville, Ohio. DAVE, E. O Capt., Co. A, 212th Engineers, Camp Devens, Mass. FOLEY, CHARLES B., Electro-Met., Martin Rockwell Corpn., 347 Madison Ave., New York,. N. Y. HOSFORD, WILLIAM F., Asst. Tech. Supt., Western Electric Co., Inc., Hawthorne Station, Chicago, Ill. HOSTER, M. T., Supt., French Creek Mines, E. & G. Brooke Iron Co., St. Peters, Pa. KAWASAKI, SHIGETARO, Chief Geol., Geological Survey of Chosen, Government General of Chosen, Keijo. Korea.

Jan 3, 1919

Reduce worker exposure to respirable dust without interfering with bag-filling operations. Approach A dust control hood was developed which contains and captures dust close to its source and prevents it from entering the bag-filling operator's work place. How It Works A sheet metal hood is placed around the nozzle of the bag filling machine. The hood is connected through ducts to the plant exhaust ventilation system. Air pulled into the front of the hood and around the sides of the bag picks up dust generated inside the hood, and carries it to the dust collector. The size of the hood can be adapted to fit most fluidized valve-type bag-filling machines. The height of the hood depends on the bulk density of the product and weight of the bags being filled. The 14-inch-width of the hood allows it to be used on multi-nozzle baging machines spaced 16 inches on center. Only 2/3 of the bag is actually within the hood, and this allows easy operator access for placing the bags on the nozzle.

Jan 1, 1978

By J. Spross

"The Key Lake mill has operated since the fall of 1983. The ore from both Key Lake open pits will be depleted by 1997. It is planned to use this mill, located about 60 km southwest of McArthur, to process the McArthur River ore.While the geological data collected so far on the McArthur deposit are encouraging, more information of the deposit is needed before any detailed mine planning can begin.The surface drilling program identified the orebody and provided information on the geomechanical and hydrological properties of the overlying sandstone. It was proposed to conduct an underground exploration program to further delineate the orebody. This was air proved following a public hearing and review process. This program involves the sinking of a 630 metre deep shaft and the driving of one or two drifts along a portion of the orebody. From these drifts, exploration drilling every 10 m to 15 m through the orebody will provide the information required for the preparation of a feasibility study and an Environmental Impact Statement (EIS)."

Jan 1, 1994

By José M. Chiroque

Ante la necesidad de ventilar las labores de la profundización en la rampa Rick 3, se genera el proyecto de ventilación denominado Raise Borer RB12 como un circuito de extracción de aire viciado. Sin embargo, por las características geológicas de las rocas encajonantes de esta chimenea y por la intemperización de las mismas por cercanía a superficie, se identificó desprendimientos de roca de las paredes de este RB, comprometiendo su estabilidad con posibilidades de atrancamiento y taponeo con carga. En consecuencia, se perjudica la ventilación de la profundización y los costos de inversión por la necesidad de construcción de una nueva chimenea. Por ello, el objetivo del presente trabajo busca garantizar la vida útil de la chimenea a través del diseño y construcción de un sistema mecánico de izaje y descenso para la chimenea RB 12A, donde se utiliza un winche, cables y una jaula, considerando todas las medidas de seguridad. Luego, fue lanzado el shotcrete y colocación de ductos metálicos en la zona ensanchada, cumpliendo con el objetivo de la recuperación y garantizando la vida útil de esta chimenea.

Sep 12, 2011

By J. C. Moreno, G. Rios, M. Palacios

The Huelva smelter was commissioned in 1970 coinciding with the shutdown of the old smelter in the Rio Tinto mine site. That new smelter consisted of two Momoda blast furnaces with a capacity of 500 dmtpd of concentrate. Nevertheless, soon after their start-up, it was clear that an increase in the smelting capacity was needed. After an analysis of the existing alternatives at that time, the flash smelting technology was chosen. The new Outokumpu Flash Smelting Furnace (FSF) came into operation on 18 September1975, with an initial capacity of 900 dmtpd of concentrate, using four Venturi-type burners and preheated atmospheric air. Since that date the Huelva Smelter team, together with Outokumpu (now called Outotec), have continuously improved our FSF design, process conditions and operational practices, leading to a present capacity of 3,500 dmtpd of concentrate. Since 1975, five smelting campaigns have been completed, the last ending in November 2013 with the rebuilding of the original FSF hearth. This paper describes the history of these improvements and the lessons learned.

Jan 1, 2014