Search Documents

By Joseph M. Denk, Gary J. Wirth

This paper summarizes a three phase face ventilation study which was conducted from September 1989 through March 1990 to determine face area methane liberation patterns on two extended longwall sections. The coal seam being mined was considered gassy and the mine liberated an average of 14.4 million cubic feet per day (cfd) or 0.41 million cubic meters per day (cmd) of methane through the mine fans. The mine also used an extensive underground degasification program to recover up to 13.4 million cfd (0.38 million cmd) of methane. Data was collected while the longwall sections were mining from the beginning, middle and end of panel extraction to determine the relationship between the methane liberation and extent of longwall retreat. As expected, methane concentrations did increase from the headgate (intake) to the tailgate (return) side of the longwall face and peak concentrations were detected above the shearer as it passed a methanometer location during mining. There were significant differences in the methane liberations due to the location of the active face within the longwall panel. Results from this study could be used to determine a minimum design face air quantity for an extended longwall section operating under similar conditions.

Jan 1, 1991

R. L. Bullock (St. Joseph Lead Co., Bonne Terre, Mo.)— The progressive approach of The International Salt Co. as described by Mr. Ryon is certainly commendable as is his paper. St. Joseph Lead Co. has been shooting AN/FO in 13/8 to 1 1/4-in. holes for several months now (as of October 1960) on a trial basis. The results thus far obtained are excellent, but conclusive evidence at this date is premature. One point that he gave should interest even the most ardent skeptic. That is, they are getting a detonation of the 1 1/4-in. ANDO charges in 2 1/4-in. holes. In light of its low sensitivity and critical diameter, this would appear to be one of the worse conditions that one could expect in which to get proper detonation of AN/FO. It has been shown* that partial confinement sometimes decreases sensitivity of a column of explosive because the air space above the explosive becomes highly compressed and in turn compresses the explosive prior to passage of the detonation front. Apparently, this does not happen in their shooting and the poor explosive coupling caused by the 2 1/4-in. holes yields a minimum of overbreak and is an ideal condition for their back.

Jan 1, 1961

By W. R. Ingalls

MANY years ago, I expressed the opinion, in writings and otherwise, that it was possible to desulfurize zinc blende autogenously, i.e., without the use of extraneous fuel, and that at some time this would be accomplished. This opinion was based on thermal calculations and also on observations of the behavior of blende during roasting in different ways, all of which observations tended to confirm the theoretical calculations. Among such observations were things like the following: Once in carrying out the stall roast of cupriferous pyrites as a regular metal-lurgical operation, I was minded to charge a stall with lump blende, ranging from walnut to egg size, as I recollect, following the same procedure as with pyrites, and setting fire to the kindling wood, observe what would happen. The blende charge ignited well enough and bravely began to burn, quite actively the first day, at a diminished rate the second day, while on the third day burning ceased and the charge quickly became cold. It was just like trying to set a grate full of anthracite afire with insufficient kindling wood. The volume of air drawn through the stall was too great, quickly cooling the entire contents below the ignition temperature, which means, of course, that burning ceased.

Jan 12, 1922

By L. W. Rowe, W. R. Opie

A brief history of TiCI, production and purification is given. Chlorinator feed materials for the production of TiCI4 are classified. The thermodynamics and kinetics of Ticl4 production by chlorination of TiO2 are discussed. Problems encountered in the chlorination and purification steps are outlined in detail. MOST of the current processes for the production of titanium metal require the use of TiC14 as a source of titanium values. This material can only be produced by a dry chlorination process, since it is immediately hydrolyzed in the presence of water. When pure, the tetrachloride is a colorless liquid boiling at 136°C. It fumes readily in moist air, reacting immediately with the moisture to form TiO, and HC1. History The tetrachloride was prepared as early as 1826 by DumasL who chlorinated a red hot mixture of carbon and TiO,. Since then, numerous other mixtures have been used including rutile, ilmenite, beneficiated ilmenites, titanium pigment, slags, and the various titanium metalloids such as TiN, TiCN, TiOC, and TiS2. S2Cl2, phosgene, and CC14 have been substituted for chlorine and CO has been used in place of carbon.

Jan 1, 1956

By L. H. Michaud

A mining company plans to extend its surface coal-mining operations in central Pennsylvania. Although the proposed site contains pyritic material, the results of the acid-base accountings for the site shows an overall Neutralization Potential to Maximum Potential Acidity Ratio (NP:MPA) of 4.26:1 for the entire site. The pyritic material is, however, associated with the lower of the three seams to be mined. If traditional dragline-mining methods are used, this would result in the acidic material being placed at the top of the spoil piles, exposing it to air and water, and therefore to the formation of acid mine drainage (AMD). Further concerns are associated with the fact that the alkaline material is not distributed evenly over the mine site. To prevent the formation of AMD, the company has proposed to mine the area using truck-shovel mining methods. This technique offers a more flexible alternative for cut sequencing and for the selective placement of waste material. Working with the Department of Mineral Engineering at The Pennsylvania State University, amine plan was developed for this site. This plan results in the layering of the alkaline and acidic spoil to achieve an overall net alkalinity in all spoil areas. Therefore, mining this site should not result in the formation of AMD.

Jan 1, 1996

By D Landriault, G W. Wilson, L Langetine and

Engineered soil covers are used for final closure options for both waste rock and tailings disposal facilities. Currently, cover construction requires excavation of appropriate cover material from a nearby site. If no suitable materials are available, the mine operation may have to ship appropriate materials long distances to the site before the construction of the cover can even begin. This has led to the proposal to engineer cover materials using existing waste materials from the mining operation. The paper presented here describes the results of a laboratory scale testing program to evaluate the potential for blending waste rock, smelter slag and tailings for the creation of a suitable cover material at a site in Canada. Tailings from the local mill, waste rock and slag were collected in the field and blended to create a material with an air entry value similar to the tailings and with physical strength similar to the waste rock. Testing indicated this mixed material could be blended at a consistency of a paste and was suitable for pumping. It can also be compacted to a high-density material. The preliminary results show that it may be possible to blend waste rock, slag and tailings into a material that can be utilised in the construction of a water retaining cover.

Jan 1, 2003

By R. V. Ramani, George W. Luxbacher

Computer simulation of mine ventilation systems, after a slow start in the early sixties, is gaining increasing acceptance for planning, design, and evaluation purposes. Numerous programs are readily available from government, university, consulting, and industry sources. The computer adage "garbage in, garbage out" is as applicable in ventilation engineering as in any other application of computers, and has been responsible for the questionable results obtained in some instances. The source of input data for a ventilation simulation is most often a pressure-quantity survey of the mine, or, in the case of a new mine, information derived from a survey of an existing mine which has conditions similar to those expected in the new mine. The crucial step is to generate simulation input data from the ventilation survey. Problems such as quantities that do not balance, pressure gradients opposite to measured air flow, differences in the pressure datum in a multi-shaft mine, modeling of leakage, and deviations in flow from the square law (H=RQ2) are frequently encountered and must be resolved. The purpose of this paper is to discuss these aspects and to propose procedures which can lead to input data for valid simulations of mine ventilation systems.

Jan 1, 1982

By F. M. Doyle, S. Duyvesteyn, K. Sreenivasarao

Toxic metals entering surface or ground water from sources such as metal finishing shop spills and abandoned mines can pose a significant threat to public health and the environment. Ion flotation and similar foam separation techniques show great promise for treating dilute, metal-contaminated solutions, and could also be used to treat effluents from many minerals and metallurgical processing operations prior to discharge. In ion flotation, an appropriate collector is added to the solution to form hydrophobic complexes with the metal ions. These metal-bearing species are then removed by flotation, usually with trace addition of a frother to stabilize the foam. In an effort to better understand the underlying scientific and engineering principles that determine the performance of ion flotation, the removal of Cu(II), Pb(II), Cd(II), Cr(II) and Cr(VI) has been studied using laboratory scale flotation columns in batch mode. The effects of the superficial air velocity, solution and froth height, nature of the collector, collector: metal-ion ratio, ionic strength and several frothers at low concentrations on the flotation kinetics are reported. Finally, results are presented on methods that might allow regeneration of collector and recovery of by-product metal from the foam product.

Jan 1, 1995

By Edward Sayre

IN shaft sinking for coal mines, the cost item greatly influences the method adopted. This holds true especially when soft material must be traversed. The average life of a coal mine is short. This is clue either to the limited area of the coal basin or to the great expense of maintenance and haulage underground when the entries are extended a considerable distance from the hoisting shaft. Therefore, the engineer in opening a coal mine is confronted with the fact that the cost must be kept within certain bounds else the venture will prove unprofitable. For this reason he may be prohibited from adopting certain safe, but expensive, methods that are used in sinking caissons for foundations, driving transportation tunnels, or other work of permanent construction. A common method of sinking through difficult ground employs the aid of a steel shoe pushed ahead of the shaft timbers. Another is the drop-shaft method. These two methods were used in sinking the main shaft and the air shaft of the Eagle No. 3 mine, at Des Moines, Ia., and the following data show the relative success and cost of the two methods of sinking under the same conditions. A drill log of the material to be penetrated was as follows (see Plate 1, Fig. .1)

Jan 9, 1916

By A. M. Gaudin, Olav Mellgren, P. L. De Bruyn

In commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena' and for chalcocite. In the work on chalcocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh,,' but the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5; at neutrality. a contact angle of 60° is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants.

Jan 1, 1956

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation's Utah Copper Division. This operation is the world's largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325. As part of this giant effort, the smelter planning team and supervisory staff considered that new, well organized, highly flexible, readily available maintenance information was essential to assist the maintenance personnel in the performance of their duties.

Jan 1, 1979

By P-M. Dupond, S. Lowrie, C. Tauziéde, Z. Pokryszka, A. D. Jones

A physical model has been developed to simulate the flows and mixing of gases in the waste of a longwall retreat coalface. The model is used in conjunction with computational modelling, and the distributions of permeability and gas emission in the model waste follow those in computer simulations (Pokryszka et al 1996). The physical model represents at 1170th scale a 200 m long, 3 m high coalface with a waste extending up to 280 m to the face start line. The model is tilted to the same seam slopes as the real face, e.g. 22° ascensional ventilation along the face and 7" slope to the dip. The purpose is to investigate the flow of three components: ventilation seepage flow through the waste; methane; and nitrogen injected to quell spontaneous combustion. A heavier-than-air surrogate gas (SF,) is used in place of methane, and therefore the model is inverted so that gas layers form along the 'roof". The main forces driving the flows in the waste (pressure gradients due to ventilation and the density difference of gas layers) are kept in proportion by appropriate scaling of the permeability. Calibration and validation used data from a coalface at a mine in the Lorraine coalfield. The model is now in operational use.

Jan 1, 1997

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Barry Silverman

As a significant mineral supplier, consumer of primary fuels, and producer of wastes and emissions to air, water, and land, the domestic copper industry through its investment and operating decisions influences the nation's economy and the environment. In turn, the copper industries' decisions are influenced by various factors: government energy and environmental policies, economic conditions, and technological considerations. The authors have developed a framework for assessing in an integrated manner the impact of these factors on the future investment and operating decisions made by copper firms. Specifically, this model is designed to capture the technology forcing nature of regulatory constraints, the differential situation of individual copper deposits and plant locations, and the price of factor inputs and conditions in the nation's economy. The capability to do this has only become real because of the decision of the U.S. Bureau of Mines to create Mineral Availability system1 or MAS. This system contains detailed but confidential information about each mine and mill in each of 35 mineral industries." Without MAS or a similar information system, the utilization of the methodology we offer would be impractical, but with. MAS it offers a unique technique of dealing with environmental-resources policy questions.

Jan 1, 1979

By G. A. Brooks

The problem of treating concentrates with increasingly higher levels of arsenic and antimony is compounded by the trend to stricter environmental guidelines regarding the disposal of smelter wastes. Much of the arsenic and antimony from non-ferrous processes is recovered as oxide fume. The options for handling these fumes include recycling them to the smelter, stabilising and disposing of them, and recovering values from them. Whilst arsenic oxide has little value, there is a market for antimony oxide and this provides an incentive for devising techniques for separating antimony oxide from arsenic oxide before disposal of the arsenic oxide. Arsenic can be separated from antimony oxide by selectively volatilising the more volatile arsenic trioxide from a mixed oxide sample or by selectively condensing the less volatile antimony tetroxide at high temperatures, leaving arsenic trioxide to condense out at lower temperatures. The results of selective volatilisation experiments at 379 to 587 °C indicate that it is difficult to achieve an arsenic content below 5.0 wt.% using air or nitrogen as carrier gas due to the formation of solid solutions between the two oxides. Injection of oxygen into a mixed vapor stream improved separation by selective condensation and antimony tetroxide containing as low as 0.23 wt.% was obtained in laboratory experiments.

Jan 1, 1994

By M Wortley, O Gu, D La Rosa, J McMaster

Metso Minerals Cisa have developed VisiofrothÖ û a system which calculates parameters of the froth surface using vision from remote cameras mounted about individual flotation cells. The parameters calculated from this system can be utilised within process control strategies to achieve stabilisation or optimisation of the flotation process. As part of a JKMRC AMIRA P9 field campaign, froth vision was collected from various cells operated at different air rates and froth depths within Rio TintoÆs Northparkes copper roughing and scavenging circuit. At the same time, samples were collected to determine the cell metallurgical performance at each operating condition. These froth images have been processed using the VisiofrothÖ system with froth velocity, bubble size, froth collapse rate and various froth colour parameters calculated. These parameters have been compared to the measured concentrate flow and concentrate grade produced at each condition. This analysis shows that the concentrate tonnage flow is strongly correlated with froth velocity whereas the concentrate grade is best correlated using froth velocity in combination with a bubble stability parameter which affects the bubble size distribution on the top surface of the froth. This paper summarises the results from this analysis as well as an overview of the VisiofrothÖ system and the parameters that are measured by the software.

Jan 1, 2007

By Arthur P. Chase

The Tacubaya subway tunnels form a link in the Sistema de Transporte Colectivo (Mass Transit System) of the Federal District of Mexico. One tunnel 327 m long lies to the north of Tacubaya Station, the other 811 m long, to the south. The tunnels are designed to accommodate two subway trains, one inbound and one outbound, within the inside diameter of 8.5 m. The designers of the tunnel lining and tunnel driving equipment were faced with the problem of driving two subway tunnels 9.0 m outside diameter through water-bearing soil, directly beneath a high speed limited access highway, a main drainage sewer, structures including residences and office buildings, on an alignment curved for 67 per cent of tunnel length, and on grades as high as 7 per cent, within a limited budget, with minimum damage to property and disruption to the community. Planning The following decisions affecting tunnel design and construction were made at an early stage of planning: Shield. To enhance safety, a tunnel shield would be used for tunnel driving. Dewatering. The water-bearing soil could be effectively dewatered; consequently, tunnel driving could be performed in free air. Hand Mining. To minimize investment in equipment, hand mining would be used to excavate and support the face.

Jan 1, 1997

Metso Minerals Cisa have developed VisiofrothTM - a system which calculates parameters of the froth surface using vision from remote cameras mounted about individual flotation cells. The parameters calculated from this system can be utilised within process control strategies to achieve stabilisation or optimisation of the flotation process. As part of a JKMRC AMIRA P9 field campaign, froth vision was collected from various cells operated at different air rates and froth depths within Rio Tinto's Northparkes copper roughing and scavenging circuit. At the same time, samples were collected to determine the cell metallurgical performance at each operating condition. These froth images have been processed using the VisiofrothTM system with froth velocity, bubble size, froth collapse rate and various froth colour parameters calculated. These parameters have been compared to the measured concentrate flow and concentrate grade produced at each condition. This analysis shows that the concentrate tonnage flow is strongly correlated with froth velocity whereas the concentrate grade is best correlated using froth velocity in combination with a bubble stability parameter which affects the bubble size distribution on the top surface of the froth. This paper summarises the results from this analysis as well as an overview of the VisiofrothTM system and the parameters that are measured by the software.

Jan 1, 2007

By John L. Reuss

A laboratory study was conducted by the Bureau of Mines to investigate the technical feasibility of decomposing hydrous magnesium chlorides by using a steam pyrohydrolysis technique. This procedure consisted of injecting steam into the atmosphere of a decomposition furnace containing samples of hydrous magnesium chloride and determining the rate of hydrolysis by measuring the rate of chloride evolution. The variables investigated were temperature, amount of water vapor in the decomposition atmosphere, and hydration stage of magnesium chloride. The application of steam was shown to accelerate both the rate and completeness of magnesium chloride decomposition reactions. For example, when magnesium chloride hexahydrate is exposed to a furnace temperature of 600' C in an air atmosphere for 20 minutes, the decomposition is 37 percent. Under identical conditions in a steam atmosphere, the decomposition is in excess of 70 percent. The magnesium oxide produced by the steam pyrohydrolysis of magnesium chloride dihydrate at 800° C contained 98 percent magnesium oxide. Based on magnesium oxide composition, this is equivalent to that of burned magnesite produced at temperatures in excess of 1,300° C. To demonstrate the quality of the product on a practical basis, metal reduction tests have shown it to be equivalent to reagent-grade magnesium oxide as a carbothermic reduction feed material.

Jan 1, 1974

By A. B. Boghani, R. H. Trent

A computer program has been developed to simulate evacuation of a mine in various configurations. The simulation input variables include characteristics of the mine, expressed in the form of a network of passages, properties of hoists and hoisting strategies, initial miner positions, ventilation and compressed air velocities, stench warning system and self rescuer capabilities. The simulation can be carried out for cases in which there is no fire, i.e., fire drill simulation, or for cases in which there is a fire at any arbitrary location. The fire is assumed to generate gases which impede movement of miners in the gaseous region. However, the thermal effects of the fire are not considered. The simulation output include the evacuation time for each miner, movement of the hoists, propagation of smoke through the mine passages and smoke exposure of the miners. Several illustrative simulations have been carried out to verify validity of the program and to demonstrate its capabilities. The computer program has been able to predict evacuation time, within 5 percent, for an actual fire drill. It is believed that this program can be used to evaluate evacuation performance of a mine, identify problem areas and demonstrate improvements due to the recommended corrective actions.

Jan 1, 1977