Search Documents

By John A. Meech, J. G. Paterson

Activated carbon is a strong adsorbent for amyl xanthate, capable of removing from solution up to a quarter of its own weight in xanthate. In selective flotation system where depression is unstable, separation efficiency increases with activated carbon additions. The improvements observed are brought about by two mechanisms. First, by removing stripped and residual collector ions from solution, competition between depressant and xanthate is reduced and depression is stabilized. In addition, the texture of the froth phase at high pine oil concentrations is modified by activated carbon such that better drainage between the air bubbles takes place, alleviating the mechanical entrapment of depressed mineral particles. In treating a bulk copper/lead concentrate produced from GECO ore, selectively between galena and chalcopyrite is increased when activated carbon is used. Although the rate of flotation of galena is marginally lowered by activated carbon, a small extension in the duration of flotation allows the lead recovery to increase by 19% at the same recovery of copper. An addition rate of 0.75 kg/ton (1.5 lb/st) of bulk concentrate is suggested as optimum from this testwork. However, the actual level used in the mill is dependent upon the residual concentrations of collector and frother in the bulk concentrate pulp.

Jan 1, 1979

By T. Clinton Taylor

QUALITATIVELY, galena (native lead sulfide) reacts with aqueous solutions of the xanthates,1 and has its surface sufficiently altered so that there is a tendency for air bubbles to attach themselves to the mineral crystals where there was no such effect before the treatment. This property is utilized in froth flotation operations where the mineral sulfide particles are raised into the froth and the gangue whose surface is not altered remains behind. The results of a study of this reaction were reported" recently and certain tentative suggestions about the interaction of galena and the alkali xanthates were offered. In this paper, there is set down the results of a detailed quantitative investigation of the ions involved in this inter-action with a view to finding out more about the condition existing imme-diately at the surface of a crystal like a heavy metal sulfide after treatment with an organic reagent. Past experimental experience showed that finely ground galena shaken with aqueous potassium xanthate abstracts xanthate ion and at the same time sulfate ion, reducing ions of the type (SmOn)= where the ratio of m to n is less than 4:1 (as in sulfate), sometimes hydroxyl ion are thrown into solution.,

Jan 1, 1933

By Francis Kendorski

One of the most dangerous events in underground coal mining is unexpectedly encountering water inrushes from undetected abandoned mines in the same seam. The surest and most confident method is probe drilling either from the mine or from the surface. However, drilling is expensive and may even miss the suspected mine voids entirely by drilling through pillars. Many operators rely upon one or more of several remote sensing techniques for detecting mine voids. However, mine "voids" often are not air- or water-filled open cavities, but are collapsed, rubble-filled chimneyed columns in the strata. Geophysical techniques, such as seismic reflection and refraction, electrical resistivity, magnetics, ground-penetrating radar, and others, often assume a continuous or fractured rock mass that has varying properties which provide the signatures that allow discrimination of one strata from another, or of strata from voids. However, a rubble-filled cavity has rock block-to-rock block contact throughout its volume and can still respond as a continuous rock mass with the rock blocks allowing signal transmission or mass detection, rather than a void space. Hydraulically, a rubble-filled cavity is essentially as transmissive to water as an open mine void. Thus, the problem of detecting a mine void with confidence is significantly compounded.

Jan 1, 2004

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) conducted a study of the explosibility of various metals and other elemental dusts, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafnium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties-from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechnic ignitors. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from "-1550K for tin and tungsten powders to "-2800K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures.

By Hassell E. Hunter

The Wyoming Minerals - Conoco Crownpoint Joint Venture represents the first time that big hole drilling has been exclusively used to develop a privately financed mine. Three shafts, one ten feet in diameter and two six feet in diameter, have been successfully drilled to depths of 2243', 2188' and 2188' respectively and lined with hydrostatic designed steel casing. The largest shaft is to be used to as a development shaft to handle muck and water from enlargement and station excavation of the other two shafts. A reverse fluid air assist circulation system with potassium base mud was used during drilling. The mud was cleaned by settling in steel lined tanks with assistance from cyclone type sand separators. Deviation was monitored with wireline gyroscopic surveying instruments at 30 foot intervals. Horizontal departure did not exceed 16 inches off perpendicular. Casing was designed to withstand full hydrostatic pressures with a 1.5 safety factor for the large shaft and 1.25 safety factor for the two smaller shafts. All casing welds were x-rayed prior to lowering the casing into the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1982

Routine, in-pit geological mapping of highwall at Central Queensland Coal Associates (C.O.C.A.) deep strip mines has proved too slow for the increasingly greater highwall lengths which require mapping. This realiz- ation has encouraged the search for faster mapping methods and after trial of ground photographic methods has resulted in the adoption of interpretive mapping off stereo cover, oblique -- aerial photography. This entails using a Cessna 182 light aircraft flying at its slowest speed, the aerial meth- od finally employed consisting of two Vinten, air reconnaissance cameras mounted in parallel and simultaneously taking both colour and black and white photographs of the mine high- wall. The respective 1:500 scale enlargements produced from the 70mm format films combine to present the sharpest resolution attainable under the field conditions pertaining and such information on weathered material as only colour photography can fully render. Total costs for the aerial photography method are estimated to be about the same as those for conventional in-pit mapping. Whilst total costs are comparable, geo- logist's time for mapping a 10 km. length is reduced to less than half that for in-pit mapping (for Stage 1, fully accurate mapping) and accuracy and detail are greatly improved. A permanent, accurate record of overburden

Jan 1, 1981

By J. Charles Miller

THE expansion of facilities for rapid transportation of perishables by train, truck and airplane has necessitated consideration of refrigerants of a minimum weight and volume per pound of cooling and has stimulated the use of solid carbon dioxide commercially. The gas probably has not had wide application in the past in air-cooling equipment for mines, theaters or buildings, owing to its thermodynamic properties, as will be deduced from examination of Table 2. However, consumption of the liquid in carbonating beverages remains a dominant factor. In addition to these uses, carbon dioxide is employed to a limited degree as an explo-sive in the liquid form, as a freezing agent in plumbing, in laboratories for low-temperature work, and in the manufacture of golf balls. SOURCES The principal sources of the gas at present are coke ovens, lime kilns, breweries and other fermentation plants, all of which are within easy reach of markets. Natural sources, however, have not received the consideration they merit, mainly because of their isolation. It is asserted by some manufacturers that the carbon dioxide gas produced from wells is unsatisfactory because it often contains impurities that are difficult to remove, while that produced as a byproduct is much purer or contains impurities that are easier to remove.

Jan 1, 1936

By R. E. Lund

Josephtown Smelter employs the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. The process uses resistance-type electric furnaces. Flow of current through the sintered ore and coke charge develops the energy required for smelting at the reaction sites. To produce zinc metal, the furnace off-Gases bubble through a large "U"-tube filled with molten zinc which condenses the zinc to liquid; the metal is then mechanically cast into slabs. To produce zinc oxide, the furnace vapors burn in air and the resultant powders are collected. The smelter comprises three distinct circuits. One circuit produces American Process zinc oxide and high grade metal; another circuit produces tailor-made alloys of controlled lead and cadmium content; the third circuit produces prime western zinc metal and feedstock which is refined into special High grade metal and French Process zinc oxide. The roasting circuit utilizes multiple-hearth furnaces for deleading the zinc concentrates; fluid bed and suspension roasters are employed for desulfurization. Sintering produces a hard, porous furnace feed. The flexible smelting process is adaptable to consuming various kinds of secondary material. Extensive residue treatment accomplishes high overall zinc recovery. Smelter by-products include sulfuric acid, cadmium, and mercury.

Jan 1, 1970

The current procedure for measuring the concentration of respirable coal mine dust is as follows. Each filter is preweighed by the filter manufacturer to ±0.1 mg. Following sampling with the Coal Mine Dust Personal Sample Unit (CPSU) at 2.0 L/min, the filter with coal mine dust is sent to MSHA for weighing. The current MSHA procedure for weighing respirable dust samples uses a Mettler Model AE163 analytical balance in conjunction with an automatic weighing system with a precision of ±0.02 mg [Tomb 19901. Each balance is calibrated twice per day. Quality control for the automatic weighing system includes the systematic weighing of one in eight filters on a second Mettler AE163 balance. Tolerance is set at ±0.1 mg between the two weighings of the same sample. Weights are truncated at the 0.1 mg level (e.g., 3.457 mg is truncated to 3.4 mg) [Bowman et al. 19851. The difference of the two truncated weights is then recorded as the weight of coal dust deposited. The respirable concentration (mg/m3) is computed by multiplying by a correction equal to 1.38 and dividing by the volume of air sampled (2.0 L/min x sampling time [min]).

Jan 1, 1997

By Keyte SG

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.1mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80% and mass yields of less than 1% can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

By R. B. Krog

Airflow patterns in longwall bleeder systems are affected by gob permeability and porosity and the condition of the gateroad entries after mining. As longwall panels are mined, areas of the caved zone and portions of the remaining gateroad entries become inaccessible, making direct ventilation measurement impossible. Mine operators are left to estimate direction and amount of airflow in the gob and the surrounding gateroads. The most readily available locations are where air enters the worked-out area, approved measurement point locations (MPLs) and/or evaluation points such as bleeder evaluation points, intake evaluation points, and the outer bleeder entry. Ventilation models (network or Computational Fluid Dynamics, CFD) can model the gob and the surrounding bleeder system but calibrating these models is difficult without field data. NIOSH installed a tube sampling system ahead of a longwall face and, as the face retreated, released a slug of tracer gas (SF6) to determine transportation times and flow rates in the inaccessible gateroads. The data was used to calibrate both network and CFD ventilation models for a longwall panel. Both model types were used to predict the airflow patterns in the gob and to determine the airflow rate from the longwall tailgate corner back to the bleeders.

Jan 1, 2011

By H. G. Papacharalambous, S. C. Sun

Experimental results indicate that wet cyclones could be effectively used for the preliminary classification of the tested synthetic abrasive materials, thus supplementing the currently used sedimentation method. An empirical formula is also proposed on the basis of the test data to calculate the particle size of separation. One of the basic operations in the abrasive industry is the classification of the crushed and ground materials into different sized products. The relatively coarse grains, plus 325 mesh, are commonly sized by dry screening with satisfactory results. On the other hand, however, the currently used grading tank, for classifying grains finer than 325 mesh, is intermittent. Consequently, it is difficult to operate efficiently and keep pace with erratic market requirements. Little success was made in an attempt to substitute air settling and continuous hydraulic settling for the grading tank, because size specifications1 for abrasive powders are very stringent and difficult to meet. Finally, a wet cyclone was chosen for experimentation. Even though wet cyclones have not been extensively used in the classification of abrasives; however, their performance as a classifier has been verified by Driessen2,4 on coal, McCarrel5 with manganese, and Herkenhoff6,7 on iron ore. Experimental work on silicon carbide, boron carbide, and fused alumina has shown that the cyclone

Jan 1, 1963

By G. A. Reinhardt, Albert Sauveur

Although many metallurgists know that some pearlitic special steels can be made troostitic, martensitic, and even austenitic, without quenching, and, therefore, without exposing them to the dangers of the quenching-bath, the practical significance of such possibility does not seem to have received the attention it deserves. Let us recall briefly the mechanism of the transformation alluded to. In Fig. 1 (after Guillet) is shown the constitutional diagram of nickel-steel; that is, of alloys of iron, carbon, and nickel. Any steel the composition of which falls within the area LPO is pearlitic after slow cooling; any steel the composition of which is represented by a point within the area MLO is martensitic, and any steel within the area MNO is austenitic. Starting with pearlitic steel, then by increasing the carbon-content or the nickel-content, or both, the metal becomes marten-sitic and eventually austenitic; that is, its composition crosses first the boundary-line LO and then the line MO—and it remains martensitic or austenitic after slow (air) cooling.' We have in this way imparted to the metal without quenching it the properties of hardened carbon-steel. In other words, the steel is now self-hardening; Nickel cannot be introduced into solid steel, but by the well-known process of case-hardening it

Jan 1, 1913

By J. B. Reed, T. A. Read, H. Rosenthal

Although the season cracking of brass has been a subject of experimental investigation for more than thirty years, the mechanism that is responsible for this phenomenon is still obscure. While at- tempts to elucidate the stress-corrosion cracking of some alloys have been relatively successful, the principal accomplishments made in the studies of the season cracking of brass have consisted of improved techniques for the fabrication of articles of alpha brass, which reduce the danger of season-cracking failure in service. The primary purpose of the present paper is to collect the published experimental data which appear to be of importance to the development of an adequate theory of the mechanism of the season cracking of brass. Some of the possible mechanisms which have been proposed will also be discussed, together with some promising avenues of future attack on the problems. Several excellent survey papers on season cracking are available, including the recent ones by Croft and Sachs(1)2 and by Gibbs(2). The principal facts concerning season cracking, as presented in these papers, may be summarized as follows. The season cracking of alpha brass is a special type of stress-corrosion failure, which may occur in atmospheres containing ammonia, air, and water vapor. The stress causing failure may be either the

Jan 1, 1945

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

By Oliver Bowles

Two striking events marked the year 1871-the establishment of the A.I.M.E. and the beginning of the portland cement industry, the most spectacular of all the nonmetallics in its development. Just as David Saylor's first portland cement, made in a little mill at Allentown, Pa., in that year was the forerunner of a mighty industry, the products of which in 1942 were made in 155 plants scattered throughout the country (having attained a value of nearly $300,000,000), so the Institute from its small beginning has attained a membership of many thousands, likewise decentralized into a series of individual sections of wide geographical distribution. Concurrent with the establishment of the Institute was also the invention of the steam drill, followed by the compressed-air drill about 1904. These mechanical drills were so immeasurably in advance of the hand drill and hammer used previously that quarrying and mining of present-day magnitude could never have been attained without them. Some outstanding occurrences have marked this eventful three quarters of a century. The concrete age, with its enormous demands for cement, aggregates and steel, is of primary importance. Of interest also is the shift of fertilizers from the organic to the mineral field. Nitrates, primarily obtained

Jan 1, 1947

By D. J. Jr. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers. 1,2,3,4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The endurance limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers.1, 2, 3, 4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The cndursnce limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By Herbert Clark Hoover, Lou Henry Hoover

IN the last book I have explained the methods of delimiting- the meers along each kind of vein, and the duties of mine officials. In this book1 I will in like manner explain the principles of underground mining and the art of surveying. First then, I will proceed to deal with those matters which pertain to the former heading, since both the subject and methodical arrangement require it. And so I will describe first of all the digging of shafts, tunnels, and drifts on venae profundae; next I will discuss the good indications shown by canales2, by the materials which are dug out, and by the rocks ; then I will speak of the tools by which veins and rocks are broken down and excavated ; the method by which fire shatters the hard veins ; and further, of the machines with which water is drawn from the shafts and air is forced into deep shafts and long tunnels, for digging is impeded by the inrush of the former or the failure of the latter ; next I will deal with the two kinds of shafts, and with the making of them and of tunnels ; and finally, I will describe the method of mining venae dilatatae, venae cumulatae, and stringers.

Jan 1, 1950