Search Documents

By Bert Sandell

MUCH has been said and written about the various uses of die-castings, their applications in the various industries and their advantages and disadvantages. Examination of this literature, however, fails to disclose any data concerning the effect of temperature upon any of the physical properties of die-casting alloys. The uses and applications of die castings are so numerous, and of such a varied nature, that far too lengthy a manuscript would be required to list all of them. Brief mention of some specific cases will suffice to illustrate the temperature ranges in which certain die castings function. Automobile hardware, such as hub caps, door handles, radiator caps, etc., can be used as one example. Castings of this type are constantly exposed to varying climatic conditions, temperatures ranging from below zero to upwards of 100° F. Refrigerator parts, such as ice-cube trays, etc., form another example. Approaching the other temperature extreme, we encounter conditions such as are found in kitchens in which oven-heat indicator parts, cooking utensils, waffle grids, etc., embody use of die castings, where temperatures as high as 500° F. are often met with. Because of this variation in service temperatures, it was felt necessary to ascertain the effect of these temperatures upon the physical properties of die-casting alloys. The Charpy impact test was chosen first because of its simplicity, and because of the fact that brittleness is more likely to be objectionable in die castings than hardness or other physical properties.

Jan 1, 1932

By Tateo Usui

In the course of carbonization of coal under a rising temperature condition, volatile matter (V.M.) is released. The kind and amount of V.M. released depend on the kind of coal. Components of V.M. are tar, hydrocarbons (CH4, C2H4, C2H6, C3H8), CO, CO2 and H2, which are released in this order as a function of carbonization temperature. When the carbonization of coal under a rising temperature condition is interrupted at a certain temperature, TC, max, semi-coal-char with residual V.M. is obtained. If some optimum interruption-temperature is chosen, small but most suitable amount of V.M., namely H2, is retained. When the semi-coal-char thus obtained is heated again under the same rising temperature conditions but up to more than TC, max (1), the residual V.M. is released from just around TC, max (1). We propose novel iron ore agglomerate bearing such semi-coal-char with some strength. While simple iron ore agglomerate bearing coal char will start the reduction reaction as solid-solid reaction at somewhat higher temperature, the proposed one will start the reduction reaction as gas-solid reaction at somewhat lower temperature but a little higher than TC, max. Samples of semi-coal-char and novel iron ore agglomerate bearing such semi-coal-char have been prepared and evaluated.

Jan 1, 2006

By Jeong-Soo Sohn

Physical treatment and chemical treatment of spent lithium-ion battery were studied in our research team. Especially we developed two types of acidic leaching for crushed powders containing LiCoO2 of spent lithium ion battery. One of them is sulfuric acid leaching with H2O2 as a reducing agent. The leaching rates of cobalt, lithium and the other metals were above 99 % at the condition of 2 M H2SO4, 10 vol. % H2O2, 75 °C, 300 rpm agitation speed, 250 g/5L solid liquid ratio and 75 minutes reaction time. And the other leaching process is the oxalic acid leaching. In this process more than 99% of Li and less than 1% of Co were dissolved at the condition of 3M oxalic acid, 80°C reaction temperature, 300rpm agitation speed, 50g/L initial solid/liquid ratio and 90min extraction time. Each process has its advantage and disadvantage. In sulfuric acid leaching, leaching reagent is very cheap and cobalt could be recovered into cobalt hydroxide. On the other hand, oxalic acid is more expensive than sulfuric acid but lithium could be dissolved selectively. Also cobalt could be recovered into cobalt oxalate and it could be changed into cobalt oxide after heat treatment. In order to select the effective recycling process, recovery rate and purity of cobalt hydroxide and cobalt oxalate were compared and it was investigated which process was more environment-friendly and economical.

Jan 1, 2006

By Francis M. Walters, Irwin R. Kramer

The substitution of cobalt for part of the nickel in Invar was found by P. H. Brace1 to lower the coefficient 01 expansion. Scott1 extended the use of cobalt to alloys of higher inflection temperatures. Such alloys have a larger temperature range of low expansion than those without cobalt, and their use up to 400' or 500°C. offers decided advantages in certain applications. However, it has been found that the iron-nickel-cobalt alloys are not stable in this temperature range. Experimental Methods Two methods were used in studying the stability of the low-expansion iron -nickel-cobalt alloys. Dilatometer specimens were held at 480°C. for 9 months and the change in expansion characteristics was dctcr- mined. Filings were held for about 2 months at various temperatures and the change in structure was determined by X-ray diffraction. As shown by Table I, the alloys studied covered a wide range in nickel plus cobalt content (which determines the inflection temperature) as well as some variation in the ratio of nickel to iron (which controls the temperature of the gamma to alpha transformation). Included also are alloys containing carbon and vanadium, carbon and titanium and three with various amounts of copper. The alloys were melted in a high-frequency induction furnace with a magnesia crucible, using ingot iron, electrolytic nickel and commercial cobalt. Fifteen-pound heats were cast into iron molds after deoxidizing with silicon, or

Jan 1, 1942

At moderate depths this question is of relatively small importance, but at depths over 2,000 feet it becomes a matter of some consequence. The rate of increase of temperature with the depth varies in different localities, but as a rough average we may take it to be about 1° Fahr. for every 50 feet of depth. The variation of temperature of the earth's surface from summer to winter penetrates to a comparatively shallow depth. At 50 feet the variation becomes practically insensible, and the temperature of the strata will be about the mean temperature at the given locality, from 60° to 75° F. in this country or the comfort of men working in the mines it is desirable to maintain a temperature of about 70° F. in the workings, or approximately the temperature of the strata near the surface.In order to obtain some idea of the magnitude of the undertaking involved in cooling a mine, I have examined the effect of placing in a long drive an apparatus by means of which we can abstract heat at a uniform rate from the drive, keeping, thetemperature nearly the same at all points of the drive at any given time.The lowering of temperature 70 F. at any distance feet from the centre of the drive (treated as a cylinder of the same sectional area as the actual drive), after an interval of time days from the commencement of the operation is given by the formula...

Jan 1, 1907

Mine Transitman.-Engineer, about 30 years of age, experienced in coal mine underground surveys. Must be good draftsman and possess sufficient personality to get results from the men. Location, Illinois. No. R 419. Coal Mining Engineer: Coal mining engineer of proved ability for position of manager f high-grade bituminous coal property. Location, Canada. No. R 427. Chemist or Metallurgical Engineer.-Chemist or metallurgical engineer for special library work. Man with scientific training with the ability and education -of a young instructor in a university. Duties would consist of working out a new method of indexing scientific information, more particularly in obtaining information for use of a Committee on the Heat Treatment f Steel. Location, Washington, D. C. No. R 470. Topographical Draftsman.-Civil engineering training and topographical and surveying experience. Unmarried man, under 40 years of age. Knowledge of Spanish not necessary. Discharged army or navy man preferred. Location, oil fields, Mexico. Salary, $5 per day, living and traveling expenses. No. R 483. Mechanical Draftsman.-Engineering training, familiarity with drawings of pumps, piping, etc., need not necessarily be a designer. Unmarried man, under 40 years of age. Discharged army or navy man preferred. Location, Mexico. Salary $5 per day with living and traveling expenses. No. R 484. Engineer Translator.-Engineer of Portuguese nationality who has received his technical training abroad, and has been filling engineering positions in this country, to translate material for catalogs of an engineering character. No. R 486.

Jan 5, 1919

By Francis M. Walters, Irvin R. Kramer

THE substitution of cobalt for part of the nickel in Invar was found by P. H. Brace1 to lower the coefficient of expansion. Scott1 extended the use of cobalt to alloys of higher inflection temperatures. Such alloys have a larger temperature range of low expansion than those without cobalt, and [ ] their use up to 400° or 500°C. offers decided advantages in certain applications. However, it has been found that the iron-nickel-cobalt alloys are not stable in this temperature range. EXPERIMENTAL METHODS Two methods were used in studying the stability of the low-expansion iron-nickel-cobalt alloys. Dilatometer specimens were held at 480°C, for 9 months and the change in expansion characteristics was determined. Filings were held for about 2 months at various temperatures and the change in structure was determined by X-ray diffraction. As shown by Table I, the alloys studied covered a wide range in nickel plus cobalt content (which determines the inflection [ ] temperature) as well as some variation in the ratio of nickel to iron (which controls the temperature of the gamma to alpha transformation). Included also are alloys containing carbon and vanadium, carbon and titanium and three with various amounts of copper. The alloys were melted in a high-frequency induction furnace with a magnesia crucible, using ingot iron, electrolytic nickel and commercial cobalt. Fifteen-pound heats were cast into iron molds after deoxidizing with silicon, or

Jan 1, 1941

By D. Bouchard, M. Forté, A. Charette

A transparent replica of a casting die was built to achieve a better understanding of the filling mechanisms of aluminum in high pressure die casting. Water and tomato paste were respectively used as analogues for the Newtonian liquid aluminum and the non-Newtonian semi-solid aluminum. The transparent die was installed on an industrial casting press and filling was filmed with a high-speed camera. Differences between the Newtonian and non-Newtonian fluids are presented and discussed.

Jan 1, 2006

By Ángel Chávez Mendoza

El presente texto describe la problemática ambiental del complejo metalúrgico de La Oroya y define conceptos y errores de los medios de comunicación sobre personas sobre la operación o cierre definitivo de la mina.

Dec 1, 2016

By Brad Wahlquist

An ex-situ biological treatment system was implemented at a gold mine site in South Dakota. The system removes selenium and nitrate from a mixture of groundwater and surface water runoff at ambient water temperatures. The Applied Biosciences? system replaced a denitrification system that did not perform consistently, did not treat for selenium and required heating of the influent water. Installation was completed in phases starting with the selenium circuit being brought into operation in February, 2002 and the nitrate circuit in March, 2002. System design can accommodate average flows of 380 L/min (100 gallons/minute) and a maximum flow of 1,136 L/min (300 gallons/min). Four cells were designed to remove nitrate from approximately 30 mg/L to below 10 mg/L and two cells were designed to remove selenium from 0.01 mg/L and higher, to below 0.005 mg/L. No pretreatment is required to operate the system at ambient temperatures, which can fall as low as -12C in the winter, and treat water at temperatures ranging between 8C to 16C. Nutrient requirements are met using a sugar based nutrient mixture that includes a balanced C:N:P:S ratio, trace elements and vitamins. Since start up, the system has consistently been in compliance for nitrate and selenium, treating water to below detection limits for both contaminants. This paper discusses laboratory biotreatability testing of a system designed to remove selenium, arsenic, and nitrate and full-scale implementation and optimization of a system to remove nitrate and selenium.

Jan 1, 2003

By David Forrest

In 1981, K. E. Drexler proposed using massively parallel nanomechanical systems to manufacture large atomically exact structures. As in macroscopic mechanical systems, they would contain components that serve traditional functions such as trusses for support, gears to transmit power, bearings for low-friction support of rotating surfaces, motors to supply torque, pipes and conveyor belts for material transport, and channels for coolant. Many of these components would only contain a few thousand atoms. Specific designs for these devices became available in the early 1990s, and a few working devices appeared in laboratories by the early 2000s. As advances continue, a thorough understanding of the operative transport phenomena will guide the intelligent design and construction of nanomechanical structures, devices, and systems. The familiar equations of continuum mechanics are generally inadequate to describe the flow of heat and mass in the proposed nanosystems. Boundary conditions often need to be described in terms of potential surfaces. Surfaces are not geometrically smooth, but periodic according to the locations of atomic nuclei. Friction occurs not due to the plastic deformation of asperities on mating surfaces, but to phenomena such as thermoelastic damping and phonon viscosity when atoms slide past each other. Electrostatic forces dominate over gravitational forces by orders of magnitude; there is no role here for natural convection. Structural components, no matter how stiff and strong, are in constant motion due to the thermal noise in the system. The fluids are described in terms of individual molecules in constant motion.

Jan 1, 2006

By L. W. Helle

In this investigation, which was conducted at the Metallurgical Research Plant, Lulea, Sweden, a series of experiments were carried out using a water-model to simulate the gas rinsing of a ladle containing liquid metal. The factors examined include the effect of gas flowrate, the position of a porous plug or lance, the immersion depth of the lance, and the geometry of the bath at the time of complete mixing. Mixing times were recorded by conductivity measurements. The results showed that there is a threshold level for mixing above which no advantage is to be gained from an increase in the gas flowrate. It is suggested that the results can be applied to rinsing ladles in working situations, the levels being approximately 270 dm3/min for 40 t ladles and 780 dm3/min for 150 t heats. The optimum siting of the lance or porous plug is a position that is three-quarters of the internal radius from the centre of the ladle with the lance penetrating as deeply as possible into the ladle. The best design of liquid bath is that having a diameter-to-height ratio of I. An equation was developed for the calculation, by dimensional analysis, of the time required for mixing during gas rinsing, and a comparison of the calculated mixing times with the results from production trials shows a satisfactory agreement (with a correlation factor of 0,91). Thus, an equation is available for the calculation of the stirring time needed to completely mix the bath in production situations.

Jan 1, 1981

By D. D. Pollock

The resistivity, temperature coefficient of resistance, and absolute thermoelectric properties of some binary terminal solid solutions of silver were determined. Equations are given which permit the calculation of these properties. CONSIDERABLE work has been done on the constitution and electrical conductivity of binary alloys of silver.1-l2 Some of these alloy studies are apparently complicated by doubtful chemical analyses. In some cases the limits of solid solubility are questionable. Those references which present electrical properties of binary silver alloys usually give just one particular set of characteristics such as conductivity (or resistivity). As a means of checking and extending this earlier work, an investigation was undertaken to describe and calculate the resistivity, temperature coefficient of resistance, and thermoelectric power of binary terminal solid solutions of silver. PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pet (by weight) of impurities. These materials were carefully weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony systems were melted in Al2O3 crucibles, under a boric anhydride cover, and poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles, and they were also covered with boric anhydride and poured into split graphite finger molds. The alloys containing magnesium and manganese

Jan 1, 1964

By E. M. Wise

MANY of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile prop-erties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. SCOPE AND CONCLUSIONS Tensile tests were carried out at room temperature and elevated temperatures up to 1100° C. on previously well annealed samples of platinum, palladium and several of their important alloys with composi-tions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100° C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the other materials tested.

Jan 1, 1938

By J. J. Egan

ADVANCES in the production of quality steel have emphasized the need for greater knowledge of the amount and distribution of oxygen in the steel. Control of inclusion content and quality is largely dependent on such knowledge. While many analytical methods have been de-vised for the accomplishment of this end, few are without serious limita-tions in accuracy, convenience, or skill required in application. Usually at least two methods are necessary to determine total oxygen and constituent oxides. Because of the great importance of this problem and the specific interest in the application of such methods of analysis, the various procedures were carefully reviewed at the Union Carbide and Carbon Research Laboratories, with the view of developing a method free from the limitations mentioned above. Intensive experimentation finally led to an improved iodine extraction analysis described by Cunningham and Price. I After this had been thoroughly checked from the standpoint of the analytical chemist, it was rechecked from that of the metallurgist. This involved preparation of a number of small heats of varying composition with determination of total oxygen in the molten metal by the alumina method2 and an analysis of the solidified material without the aluminum addition by means of iodine extraction; the oxides of iron, manganese, silicon and aluminum also being determined by the iodine analysis. The report of this work constitutes the subject of this paper.

Jan 1, 1933

By John A. Shuster

INTRODUCTION Controlled ground freezing for mining and construction applications has been in use for over a century. Despite the great technological evolution which has occurred during this period, ground freezing is still used on projects today with much the same basic technology as that used originally over 100 years ago. Major developments have occurred in the separate fields of frozen soil mechanics, refrigeration, and heat transfer analysis. However, except for a few projects in Europe and Asia, these developments have not been combined to upgrade ground freezing techniques to their potential level. In view of this situation, it is believed desirable to examine the art of ground freezing in light of recent technical developments, together with highlights on some of the apparent advantages, disadvantages and economics of the various alternative approaches. The purpose of this paper is to attempt such an examination, with particular emphasis on the practical application of presently available technology. GENERAL ADVANTAGES AND DISADVANTAGES Ground freezing may be used in any soil or rock formation, regardless of structure, grain size or permeability; however, it is best suited to soft ground rather than rock conditions. Freezing may be used for any size, shape or depth of excavation and the same physical plant can be used from job to job despite wide variation in these factors.

Jan 1, 1997

By W. V. Kotlensky, H. E. Martens

In an earlier communication, Ref. 1, the authors presented the tensile properties and the changes in crystal structure and microstructure for pyrolytic graphite tested at 2750°C. It was suggested that changes in the structure may have an effect on the tensile properties of this material. Accordingly, tensile tests were run on a series of specimens, from one block of pyrolytic graphite, some of which were hot-worked by being strained at 2750°C, others of which were tested in the as-deposited condition. According to the manufacturer, General Electric Co., the polycrystalline material was deposited at 2100°C on a substrate of synthetic graphite by decomposition of a dilute natural gas mixture. The as-deposited material had a density of approximately 2.19 g per cc, and as shown in Fig. 1 had a structure of medium size growth cones which were regenera-tively nucleated. All specimens had a gage section 0.75 in. long by 0.06 in. wide by 0.1 in. thick with the thickness direction perpendicular to the basal planes. The testing method and equipment used have been previously described, Ref. 2 and 3. For both the hot-working and the testing the load was applied parallel to the basal planes; a cross-head speed of 1.5 x l04 in, per sec was used. All heating was done in an atmosphere of bottled helium.

Jan 1, 1962

By M. S. Basich, J. S. Scope1, J. H. Raeder

During 1983, The Youghiogheny and Ohio Coal Company's lost-time-incidence rate was 8.1, equal to the average for underground bituminous operators. How- ever, one half of all lost-time injuries were low back, back and neck related. In reviewing these results, we determined that substantial improvement could be made. We investigated existing back schools and the possibility of opening an in-house clinic. In September 1984, we began The Youghiogheny and Ohio Coal Company's Back Care Program. The objectives of the program are to reduce the number of back injuries incurred at the work site, hasten recovery time, decrease medical and workers' compensation costs and provide the employee with a thorough understanding of his problem. A state-of-the-art clinic capable of treating injuries to the spine and extremities has been established at the work site. The clinic is staffed by a licensed physical therapist and is offered to all employees on a voluntary basis under physician referral. The approach to treatment is multi-phasic. For the typical patient, the initial goal is to reduce pain and correct dysfunction. Treatment modalities such as auto-traction, extension exercises, ultra sound and moist heat are frequently used. During this period the patient is given extensive education regarding his problem. As soon as more vigorous activity can be tolerated, a work-hardening pro- gram consisting of job simulation activities designed to improve flexibility, strength and functional capability is begun.

Jan 1, 1986

By R. W. Smith, M. E. Brookes

The temperature at which th: quenched 0' (ordered bcc) phase transfo.rms to the ( (complex hexagonal) phase on heating has been examined for certain Ag-Zn and Ag-Au-Zn alloys using an electrical resistivity method. The transition temperature decreases by approxinzately 7°C as the zinc content is reduced by 1 at. pct. The critical temperature, Tc, for long-range order has also been measured for a number of Ag-Au-Zn alloys. Extrapolation to zero gold content suggests that Tc decreases by approximately 5°C per 1 at. pct reduction in zinc content. The 0 phase of the Ag-Zn system exists over a narrow range near the composition Ag zn,' Fig. 1, and has a bcc structure which is disordered above 272°C. Slow cooling to temperatures below the range 274"/258"C allows the complex hexagonal phase, r° to form.2 This is the stable structure at room temperature.3 Upon quenching 0 -phase alloys from high temperatures, it is found that the 0 — (' transformation is suppressed; but ordering takes place (i.e., 0 -0'). This ordered structure can also be obtained by the room-temperature aging of cold-worked (0.4 Deformation of the 0' phase gives rise to a fur- ther hexagonal phase ( (of nearly ideal axial ratio) which reverts to b' within a few hours.= In view of this, it has been suggested that the equilibrium struc-

Jan 1, 1969

By Henry J. Williams

The main difficulty in the determination of silicon in pig-irons containing very high percentages of that element, has been due to their almost complete insolubility in acids, or mixtures of acids. The object of the present paper, which presents no new principle, is to suggest a method of determination which has repeatedly given accurate results, and which obviates completely the tediousness and uncertainty of the usual slow solution in acids. This method has been tried with pig-irons containing from 7 to 14 per cent. of combined silicon, and properly called ferro-silicons. When reduced to an impalpable powder in the agate mortar, an 11 per cent. ferro-silicon was found to resist the action of all acids, or mixtures of acids, with the exception of sulphuric acid of about 1.25 specific gravity. But the action of this acid, even during long continued heating, was very slow, 72 hours being necessary to com pletely dissolve half a gramme of the metal. The complete decomposition of 1 gramme of the metal may, on the other hand, readily he effected in a few minutes by fusion with sodium carbonate in a covered platinum crucible over a blast-lamp —the idea being to dissolve the silicon, leaving the iron in condi tion to be readily attacked by acids. The silicon dissolves as soluble sodium silicate, and metallic iron remains in a very spongy and finely divided condition. The addition of a little hot water

Jan 1, 1889