Search Documents

By T. L. Joseph

THE United States Bureau of Mines has been studying the blast-furnace process for, about ten years. An experimental furnace was developed by the bureau in cooperation with the Minnesota School of Mines Experiment Station, University of Minnesota. Many data have been obtained and published.1 Royster, Joseph and Kinney§(48) found that the particle size of ore had an important effect upon the blast-furnace, process. Kinney(28) stated: Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft, the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of the stock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and the gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. It is obvious that fine ore particles occurring in the ore as charged, or . formed in the furnace due to heat and mechanical action, place a definite limitation upon the efficiency of the operation. There is also an economic loss of fine material as dust.

Jan 1, 1930

By G. W. Tuffnell, S. Floreen

Three Fe-18 pet Ni-base ternary alloys cortaining carbon, molybdenum, or cobalt were aged to pgroduce hardening by carbides, Ni3Mo, or ordering, respectively. Each alloy was tested in rotating-beam fatigue tests after hardening to 195 ksi ultim.ate tensile strength. The fatigue properties of three alloys soere essentially identical. The results suggest that tlze fatigae strength of an igron-base alloy should depend primarily upon the tensile strength, and not iipon the hardening mecaanisrn. THE fatigue strengths of many steels have been found to be directly related to their ultimate tensile strengths. For ultimate strengths below 200 ksi, the fatigue endurance limit at 107 to 10' cycles is approximately half the ultimate strength. Essen- tially all of the steels that have been tested, however, have been hardened by carbon. Thus it is not certain whether the relationship between fatigue and ultimate strengths is a general one that applies for other types of hardening in steels, or whether it applies only for the particular method of hardening by carbon. The recent developments of the martensitic precipitation-hardened stainless steels and the marag-ing steels have shown that it is possible to achieve high strengths in iron-base alloys by other hardening mechanisms than that due to carbon. Therefore, it is now possible to compare the fatigue properties of several iron alloys having the same ultimate strengths but hardened by different mechanisms. For the present study a binary Fe-18 pct Ni martensite was selected as a base material. This particular matrix composition has been found to have deformation characteristics very similar to pure iron.' Three ternary alloys were prepared by adding either 0.23 wt pct C, 5 wt pct Mo, or 20 wt pct Co to this base composition. After suitable heat

Jan 1, 1965

By J. Wild, M. Ounpuu, G. Chevalier

"The requirements for a finer grind at Heath Steele have resulted in the investigation of agitated milling as a cost effective alternative to conventional tumbling ball mills.The grinding unit is a vertically agitated, or stirred ball mill. Grinding occurs as the result of the motion of a single vertical rotor equipped with protruding pins which impart a stirring action to the ball charge. A comparative evaluation of a 30 kW SALA Agitated Mill (SAM), and a 1.5 m x 2.5 m copper-lead regrind ball mill has been conducted at Heath Steele.An overview of agitated milling as it applies to the reduction of sulphide ore will be the primary topic for discussion. Specific parameters including energy efficiency, media consumption, operating costs, and the mechanical aspects of the SAM operation will be presented.Evaluation of the agitated mill has shown that improved grinding performance at much lower work indices than those of the conventional ball mill is possible. Media consumption has proven to be comparable on an average g/kWh basis, but the mechanical availability of the mill has been low.INTRODUCTIONConventional tumbling ball mill grinding has proven to be an energy inefficient process. Energy losses occurring within the ball mill itself can be attributed to particle friction without breakage, kinetic and potential energy losses, plastic and elastic deformation and the production of heat and sound (Lynch, 1977). It can be generally stated that a certain amount of the input energy will be converted to another form as a necessary by-product of particle breakage. Theoretical interpretation of experimental results indicate that the energy required for breaking the ore particles in a ball mill varies between I% and 25% of the total energy input (SME, 1985)."

Jan 1, 1993

By T. P. Floridis

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960

By R. H. Lee

Without doubt, one of the most frequent and serious ani~oyailces connected with the practical running of a blast-furnace, especially in single-furnace plants, is caused by low steam, in spite of the fact that all boilers at blast-furnaces have grates for burning coal, and that coal is more or less continuously burned upon them, from three to a dozen men being pretty constantly engaged around the boilers as firemen or coal- and ash-handlers. At times, when the furnace is " tight," all available men arc put on to assist the regular firemen; yet sufficient steam cannot be got to keep the engines up to their regular number of revolutions, while the stoves, deprived of the gas which has been sent to the boilers, run cold, so that, when the furnace loosens up and resumes the regular rate of driving, the blast is very considerably below normal temperature, and a "cold," or at best a " high-sulphnr," cast is the result. Again, it often happens that a furnace, running at its best, becomes temporarily a little too hot: the pressure rises; the amount of gas made is diminished; the steam soon commences to go down; and a small scaffold is likely to form before the furnace has been brought back to the proper rate of driving, and thus enabled to take its regular amount of blast. The usual remedy is either to "jerk" the furnace by a sudden, brief intermission in blowing, or to cool the furnace by lowering the heat of the blast; but if the lower blast-temperature be maintained too long, the hearth and descending stock may be cooled below the " critical temperature" mentioned by Mr. Johnson,' and the furnace may go to the other extreme, and become cold. This is especially the case when coal or coke high in sulphur is used.

Jan 1, 1907

By F. P. Dewey

Recent discussions have furnished to the members of the Institute much information concerning aluminum and its applications. The present paper will be devoted almost entirely to the description of a process by which the metal is produced in the form of alloys. The characters which especially distinguish the Heroult process consist in electrolyzing a mass of molten alumina (Al2O3), and at the same time alloying the separated aluminum with a heavy metal, the heat necessary for the fusion of both the alumina and the alloying metal being supplied by the direct passage through the molten Al2 0, of an electric current of high amperage and low voltage. The process has been in active operation at Neuhausen in Switzerland for about two years. It is also in active operation at Froges in southern France. Both these locations were selected for this purpose on account of the presence of large and desirable water-powers. The apparatus consists of a carbon containing-vessel, which may be a single crucible for small operations, or may be built up of slabs or blocks of carbon for large and industrial operations. When built up of slabs or blocks, the whole is surrounded by an iron casing. In the earlier crucibles this iron casing was cast around the carbon, in order to secure close electrical contact. This, however, has been found unnecessary; and in the later crucibles the casings consist of plates bolted together, while pulverized carbon is packed between the carbon blocks and the iron. Electric conductors are united direct to this iron casing, and the current passes from this through the carbon lining to the interior of the crucible. By this

Jan 1, 1890

By J. Brian Eby

Contact metamorphism of coals is any physical or chemical change in the character of a coal directly attributable to heat of surface or intrusive igneous rocks. Coal beds so affected are found in the United States, England, Alaska, Mexico, New Zealand, Greenland, and other countries. Particularly in the United States, there is a wide occurrence of contact altered coals; conspicuous examples are found in Colorado, Utah, New Mexico, Illinois, and North Carolina. During a recent examination of coal beds on Yampa River, in northwestern Colorado, the author had an opportunity to make some detailed observations on the contact metamorphism of coals. In this field, coals over an area of 20 sq. mi. have been affected by dikes, sheets, and sills;' samples of the coals were systematically collected and analyzed,2 with the view of obtaining more specific data on the character of these alterations. The investigation was threefold in purpose: to secure information on the lateral effects of a dike cutting a coal bed, on the range in vertical effects on coal beds overlying sheets or sills, and on the range in the vertical effects on coal beds underlying sheets and sills. Favorable field conditions, such as fresh outcrops and newly dug prospects, made possible many of the field observations and collections. The coals studied in this field belong chiefly to the Mesaverde and 11Laramie" formations. The Mesaverde coals, on the average, are blocky low-rank bituminous coals; the "Laramie" coals, which are considerably younger, are of subbituminous rank. The coals of both formations, in the northeastern part of the Yampa field, have been greatly affected by basalt intrusives, yielding all variations of carbonized coal from natural coke to the unaffected material. The igneous rock that directly affects the coals is a fine-grained olivine basalt that is intruded, in sheets up to 200 ft. thick, into the coal-bearing

Jan 1, 1925

By J. A. Bartnik, Gerald D. Rose, William H. Benson

New techniques in the magnetite and heavy media beneficiation industries demand more efficient magnetic dispersion and flocculation of the finely ground particles. Demagnetizing coils must produce several major effects, such as improving classification and screening efficiency, decreasing moisture content in filter cake and improving separation selectivity and green pellet properties. Likewise, magnetic flocculators must increase filtering rates and the settling rates of solids, improve magnetite recovery and produce cleaner water. To improve the design of equipment and to conduct tests leading to the optimization of such dispersion and flocculation, a program was initiated at Eriez Magnetics. The major conclusions reached are: 1. Laboratory and plant scale tests conducted on magnetite products show that a demagnetizing force of 450 rms oersteds at 60 cycles for 1/20- second duration will depolarize natural magnetite particles coarser than approximately 10 microns. This has been found satisfactory for most applications. 2. Effective flocculation of magnetite was obtained when a slurry with more than one percent magnetite was exposed for a period of approximately 1/15 second to a 600-gauss field. 3. The cost of demagnetizers (or flocculators) increases rapidly for larger diameter pipes. In order to reduce the cost, narrow rectangular sections are recommended for magnetic flocculators. 4. For minimum operating cost, permanent magnetic flocculators are ideal, chiefly because they do not require any maintenance and have no operating cost. 5. A newly designed electro-demagnetizing coil with high heat dissipation and a nonmetallic core provides high efficiency and long life. 6. To select the correct magnetic flocculator (or demagnetizing coil) the following information is necessary: a. Magnetic product susceptibility b. Magnetic product coercive force c. Percent of magnetic product d. Flow rate e. Viscosity f. Structure of magnetic product

Jan 8, 1968

By J. E. Hackford

IN SOME research. work carried out by the writer, certain results have bean obtained which bear on the fundamental nature and origin of coal and the relationship between coal and petroleum. Without entering into a discussion of the details of the experiments, which were conducted on petroleum and derived bitumens, there are given here, by way of definition, some of the relations that the writer has established between certain classes of bitumens of petroliferous origin. Bitumen.-A natural organic substance, gaseous, liquid, or solid, consisting of hydrocarbons and the oxy- or thionic derivatives of the same, or of a mixture of all three. Diasphaltenes.-Those portions of bitumens that are soluble, in ether or carbon disulfide, but are insoluble in a mixture of equal parts of ether and alcohol. Diasphaltenes are produced by the oxidation or thionization of petroleum oils; they have, as the name indicates, twice the molecular weight of asphaltenes, into which they are converted when subjected to moderate temperature. For example, an artificially produced diasphaltene, which was readily soluble in pentane and ether, was quite insoluble in either of these solvents after heating for three weeks at a temperature of 100° C., and was converted into an insoluble asphaltene. Asphaltenes.-Those portions of bitumen that are insoluble in ether or ether alcohol but are soluble in carbon disulfide. Asphaltites.-Those solid or semisolid natural bitumens that are composed, for the most part, of asphaltenes or diasphaltenes. A pure asphaltite1 would be composed wholly of asphaltenes and diasphaltenes, but most asphaltites contain small percentages of oil and wax, which have not yet been converted into asphaltenes; they may also contain a small percentage of kerotenes, which represent the next stage of the metamorphosis of asphaltenes. Among the naturally., occurring oxyasphaltites may be mentioned grahamite; and among the thioasphaltites, gilsonite.

Jan 8, 1920

By R. G. Ward

The temperature gradient in the subhearth metal or "salamandern of the iron bhst furnace results in the establishment of gradients in the concentrations of silicon, manganese, carbon, and sulfur. The temperature and compositional variations observed in three blast furnaces are analyzed according to irreversible thermodynamics and the systems appear to be close to the steady state condition. Apparent heats of transport, Q, for silicon, manganese, carbon, and sulfur are found to be respectively -17.5, -5, -2.1, and+22k cal per g mol. In conclusion the significance of thermal diffusion in extraction metallurgy is briefly discussed. INCREASING interest has been shown in recent years in the application of irreversible thermodynamics to metallurgical problems. In particular studies have been made of the transport of matter in thermal gradients1-' and under chemical gradients imposed by a binary solvent However, no detailed example in extraction metallurgy has been reported although gradients are the essence of many extractive processes. The case of the distribution of elements in molten blast furnace iron under a thermal gradient is discussed here. DATA In blast furnace operation the hearth bottom is often extensively destroyed by molten metal, and the metal may penetrate perhaps 10 ft into the furnace foundations forming a "bear" or "salamander". Several hundred tons of molten metal may thus exist beneath the level of the conventional tap hole and remain relatively undisturbed for several years under a thermal gradient. This system is subject to little convective stirring because the temperature decreases from top to bottom, and mechanical stirring due to movements in the stack and to tapping operations is unlikely to penetrate far into the metal. The system may thus be regarded as static

Jan 1, 1963

By Brigitta Hassler

INTRODUCTION In the early 1960's research was begun in Sweden to improve the agglomeration of our domestic iron ore concentrates (5). Different agglomeration methods that were used in the building material industry were studied under the economic support from the Swedish Technical Council, the Swedish Board of Technical Development and by the Swedish industry. The research work was performed at the Division of Mineral Processing at the Royal Institute of Technology in Stockholm. All known agglomeration methods were reviewed and the methods were developed to produce superior quality agglomerates (6). The term cold bonding (in contrast to sintering) was introduced to describe the induration operation in these processes and this has been accepted internationally. Even though we used it mostly for steam autoclaving methods, it has come to describe a class of processes that use binding methods by pore filling. Schumacher in Germany discovered around 1907 that a strong material can be produced by mixing slaked lime with fine ground quartz and subjecting to a steam atmosphere under pressure at about 185ºC. This started development of lime-sandstone building materials and later on, in Sweden, the light-weight concrete. Schumacher also used the same reaction for briquetting iron ore concentrates by adding silica and lime, and autoclaving. The product seems to have been accepted for blast furnace burden and the process was used on an industrial scale until the 1920's. The sintering method has a small melting phase as diffusion medium and in the steam-autoclaving method a small quantity of water condensate at about 200°C serves the same purpose. Thus the induration process by the hydrothermal hardening methods is similar to that of sintering or heat treatment.

Jan 1, 1977

By F. Keeler, C. M. Craighead

Aluminum alloys containing magnesium and silicon are susceptible to strengthening and hardening by suitable heat-treatments, and they constitute a class of alloys of considerable commercial importance. Generally, they contain these two elements in the proportions required for the formation of the intermetallic compound Mg2Si, or an excess of silicon; no commercial wrought alloys are made with an appreciable excess of magnesium. The reason for not having excess magnesium is obvious from the results given in this paper, since it is shown that excess magnesium results in a proportional decrease in the solubility of Mg2Si. This is the eighteenthl of a series of papers from the Aluminum Research Laboratories dealing with the equilibrium relations in aluminum-alloy systems; most of the previous publications concerned binary aluminum-alloy systems; this is the fourth of a group pertaining to ternary aluminum-alloy systems. The work on this system was completed in 1930, but the results were not published because of the pressure of other work. Hanson and Gaylor2, in 1921, presented the results of an extensive investigation of the aluminum-magnesium-silicon system. Their results indicated that an excess of magnesium over the amount required to form the compound MgzSi caused a noticeable decrease in the solid solubility of MgzSi in aluminum. A more recent investigation3 in these laboratories showed that the solid solubility of MgzSi in aluminum was 1.85 per cent at 595' C. and decreased to 0.30 per cent at 300' C. The results of the latter investigation were used as the basis for the present work. The Present Investigation In the present investigation, a study was made of the effect of various amounts of excess magnesium upon the solid solubility of MgzSi in

Jan 1, 1936

By Frank Alfred Fahrenwald

A complete list of the elements as given for 1915 includes 18 that melt above 1,700" C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures*and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,' of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation. , Historical.—The alloys of tungsten and molybdenum have received very little consideration during the past. A review of available literature reveals very little regarding this system, and that which has been recorded seems to be at fault. Mennicke2 writes, "Die bekannteste Verbindung

Jan 1, 1917

By A. L. Field

WOOLSEY McA. JOHNSON, Hartford, Conn. (written discussion).¬When ;we regard the number of British thermal units running into the billions that-must be applied to metallurgical slags in the United States, we cannot but conclude that the physical chemistry of-slags is a very important subject when measured in dollars and cents. A further contemplation of the subject shows us that it has been hitherto treated in too purely a practical manner. It is needless to comment at length on the cost of these heat units and on the cost of fluxes to produce these metallurgical slags, for, it amounts to tens of millions of dollars annually. Accordingly, this research is of value to the country. But we must,all balance our results against our efforts. Therefore, while the speaker is unwilling to criticise unduly this meritorious research, lie does criticise it in the interest of the profession for the reason that it seems to him too highly theoretical. The article is much too, scientific to produce results at a minimum cost. Let us explain our meaning. It has been said that there are always two sides to a question. It may be further said that there are always three sides to a question, the two extremes and the middle ground. In any industrial research there are the highly theoretical side, the purely practical side, and the theoretico-practical side. To study a slag and be practical in the studying, there is something needed that represents in the laboratory (or in microcosm) what actually happens macrocosmically in the blast furnace. There is such a thing as the art of metallurgical research occupying the middle ground between theory and practice.

Jan 4, 1917

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits, and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems, installed and operated in small thin-seam mines, are presented in this report. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems are proposed, which offer alternative coal recovery systems that alleviate the serious health and safety concerns of current small mine operations.

Jan 1, 1999

The common notion that the Box Hole Bore mineralization represents a variant of the Mississippi Valley type, has not been supported by the present investigation. Most of the common characteristics of Mississippi Valley type, namely 1. saturated saline brines; 2. low temperature domain; 3. mineralization in intraformational breccias and collapsed anticlinal structures; 4. hydrocarbon-rich or foetid carbonates, and 5. very simple geochemistry seem not to be applicable. The Box Hole Bore mineralization features: 1. moderately saline brines (18% NaCl); 2. very high temperature (495¦-520¦C) and low density brines, of critical vapour:water ratio and low pressure of formation (700 bars); 3. mineralization confined by faults and ex- tending laterally into carbonates of high pore volume such as stromatolitic dolo- mites; 4. ore environment characterized by oxidizing conditions, such as ferruginous carbonate and silica sands of high energy environment (heavy mineral banding) and 5. more complex geochemistry than is normal for Mississippi Valley type deposits (copper sulphosalts, and appreciable silver content). Additionally, the ore has un- usual textures formed by the replacement of carbonates and barite by large idiomorphic galena crystals. The pressure and temperature domains of the Box Hole Bore mineralization indicate post- Devonian emplacement and local high heat flow, possibly related to the Alice Springs Orogeny. Because of high lead and zinc trace element con- tents (100-600 ppm) of the carbonates, even out- side mineralized areas, it is possible that the mineralizing fluids have derived their metal con- tent from a local source, possibly aided by evap- oritic concentrations of the tidal to supratidal sequences. The new model for Box Hole Bore gives treater importance to the confining faults.

Jan 1, 1984

By Webster Hodge

MALL generators and motors are required to Soperate, in some critical applications, at temperatures where cold-worked silver-bearing copper re-crystallizes. Copper containing up to 30 oz Ag per ton has been used for many years to build the highest grades of commutators and slip rings. With failure of commutators impending because silver-bearing copper cannot withstand the stresses imposed at these higher temperatures, Cr-Cu was tried as a substitute with varying degrees of success. Cr-Cu proved difficult to fabricate because a critical heat treatment was necessary to obtain sufficient ductility. Besides, its rupture strength was shown to be low at operating temperatures, its electrical conductivity lower than desired, and its cost high. Furthermore, it often contained hidden flaws. The Nippert Electric Products Co. set out to find a better material by undertaking a research project with the stated objective of providing a material suitable for commutators that would have 1) a softening temperature above 750°F (400°C), 2) a minimum electrical conductivity of 90 pct of that of pure copper, 3) a strength not less that that of cold-worked silver-bearing copper, and 4) a materials cost of not over 1.5 times the cost of copper containing 25 to 30 oz Ag per ton. No commercial alloy met these specifications. However, it was found that copper containing from 0.18 to 0.35 pct Zr could be produced quite easily in the laboratory, and promised to fulfill the major requirements noted above. Interest naturally centered in the lower part of this composition range, since such alloys gave somewhat better electrical conductivities, and were lower in

Jan 1, 1958

By Hideki Yamamoto, Norihiro Murayama, Junji Shibata

"Hydrothermal syntheses of zeolite from coal fly ash were carried out by using various alkali sources. NaOH, Na2CO3, KOH, K2CO3 and their mixture were applied for an alkali source of zeolite synthesis. The various physical properties of the reaction product, such as the kind of zeolite crystal, cation exchange property, surface texture and so on, was investigated through the zeolitization reaction from fly ash. The mechanism of zeolitization reaction was considered from these results.Zeolite P(NaP), hydroxysodalite(HS) and chabazite(K-CHA) are synthesized as zeolite species, when fly ash hydrothermally reacts in various alkali solutions at 393K. The crystal structure of the products obtained in NaOH solutions for 3h changes from NaP to HS with increasing NaOH concentration. K-CHA formation in KOH solutions needs 10h of reaction time, which is longer than that of NaP or HS.Dissolution, condensation and crystallization steps exist in the zeolitization reaction from fly ash, and the particle surface of products remarkably changes in each step. The fly ash is spherical particles and the surface is smooth(Fig.1(a)). The dissolution of fly ash occurs in the heating process until 393K, and the particle surface changes like unevenness(Fig.1(b)). In case of NaP, the condensation of aluminosilicate ions takes place at 373-393K, and the amorphous aluminosilicate is deposit on the unreacted fly ash(Fig.1(c)). The crystallization of NaP already begins to occur at 393K and the surface is covered with fine zeolite crystals for 24h(Fig.1(d))."

Jan 1, 2003

By Clarence P. Linville

It is recognized that, in all metallurgical operations, the greatest possible uniformity in all conditions is essential to the best results. It is the constant aim of metallurgists to secure this uniformity, and their success in this respect has been in many cases the cause of great advances in the metallurgical processes themselves. Of all such processes, the production of pig-iron in the modern blast-furnace is perhaps the most complex and the most difficult of control. Notwithstanding the great progress of recent years, there is still great difficulty in obtaining anything like uniform conditions and results in the manufacture of pig-iron. The reason is not far to seek. The ores vary in composition and physical properties, often carrying a varying amount of gangue material, unevenly distributed. The coke may vary in composition, cell-structure, moisture, hardness, and other properties. The blast, the weight of which far exceeds that of any other constituent, varies in its moisture-content and consequently in its chemical composition; and its temperature, by reason of the method of heating, is not uniform, but, besides varying from time to time with atmospheric and other outside conditions, has a maximum and minimum for every changing of stoves. Now, with regard to these variations, the modern demand for uniformity has been greatly aided. Chemical analysis has made it possible to select ores so that the composition of the charge can be kept fairly constant; coal may be obtained from a given field, and coked in the same kind of ovens under conditions which make the fuel practically uniform; the Gayley

Jan 1, 1911

By Henry Howe

THAT the quiescence of a liquid while it is solidifying should favor the formation of columnar crystals, normal of the cooling surface, is seen readily on considering the mechanism of solidification. First; each particle of any composite liquid, whether it be an aqueous solution or a molten metal; in solidifying splits up into two parts, different in composition and hence in fusibility. One part is infusible at the, existing temperature, - and hence solidifies, and in general attaches itself to the inclosing walls of metal which have already, solidified; A, Fig. 1. The other part is, fusible at the existing temperature and hence remains molten. In the case of carbon Open steel, the part. of each drop which actually j; Sea solidifies is poorer, in carbon than the drop itself was before it began to solidify, and this impoverishment of the solidifying,. half-drop enriches . the other, half-drop in carbon, and Layer of Liquid thus. makes it unfreezable at the existing tem- Fig. 1.MECHANISM OF perature. SOLIDIFICATION. By this- mechanism there arises during solidification a " littoral" or shore layer- of liquid, B, Fig. 1, bathing the already solidified. walls, and more fusible than either those walls or the great remaining central mass of liquid or "deep sea," C, from which it separates them. It is essential that we grasp clearly this conception of a fusible littoral molten layer coating the already solidified walls and separating them from the deep sea. Meanwhile. heat is flowing rapidly outward through these walls, its escape cooling them, so that if any given particle of the deep sea metal

Jan 2, 1919