Search Documents

By Motoyasu Sato

Highly pure pig irons were produced in a multimode microwave reactor from powdered iron ores with carbon as a reducing agent in the nitrogen atmosphere. The grains in compacted powder absorb microwave energy selectively. Microwave-matter interaction creates thermal non-equilibrium state microscopically and enhances chemical reactions and the phase mixing at the grain boundaries very rapidly. The visible light spectroscopic techniques was used to monitor the progress of the reactions. Up to 650°C, the heated powders radiate the continuous spectrum of blackbody emission. The small non-equilibrium hot spots rise, move and finally burst in to brighter light emitting from all over the surface at 650°C. CN molecules and Fe (I) atoms were identified in the recorded spectrum. These bursts are similar to the ?ignition propagation? normally observed in chemical reactions. The line spectra originated from CO molecules have not been detected yet. The solid-solid reaction could be expected between the iron oxides and carbon to produce CO2 directly. A loss in the sample weight was accelerated during the excess-emission. These are the clear evidence that microwaves cause thermally non-equilibrium state and accelerate reduction process. The reduction of iron ore is completed at 1380°C and relatively very pure pig iron was produced. It should be noted that the impurity level of Mg, S, Si, P and Ti is only 5-10% of what is found in the pig irons produced by modern conventional blast furnaces in the steel industries. The necessary amount of carbon needed was 1/2 compared to conventional blast furnace to produce the unit weight of steel, if we applied renewable energy or nuclear power for the microwave excitations.

Jan 1, 2006

By D. J. Jr. McAdam

PART I.-OUTLINE OF INVESTIGATION, DESCRIPTION OF METHODS AND MATERIAL Previous Investigation of the Influence of Stress on Corrosion IN 1917 Haigh1 presented evidence that under simultaneous corrosion and cyclic stress metals may fail at lower stresses than if the corrosion is prior to the cyclic stress. In 1926 the author, while investigating the cooling effect of water on the fatigue resistance of metals, found that under these conditions steel specimens fail at stresses far below the endurance limit.2 (By "endurance limit" is here meant the fatigue limit obtained with specimens as free as possible from stress concentration and corrosive influences.) This led to an investigation (at the Naval Engineering Experiment Station, Annapolis, Md.) of the influence of cyclic stress on corrosion. This investigation maybe divided into three parts. The first part was a general survey of the conditions necessary to cause complete failure under corrosion and cyclic stress of relatively high frequency. The entire process by which metals fail under these conditions was-called "corrosion-fatigue." "Corrosion-fatigue limits" for a large number of metals were determined and the relationships of these limits to chemical composition, heat treatment and physical properties were established. The conclusion was reached that corrosion-fatigue is due to the accelerating influence of cyclic stress on corrosion. Results of this part of the investigation were presented in five papers.2-6 The second part of the investigation was a preliminary study of the influence of cyclic stress on corrosion. Each experiment was conducted in two stages. The first was a corrosion stage in which the specimen was corroded under cyclic stress; the second was a fatigue stage, in which the previously corroded specimen was tested (without further corrosion) to determine its fatigue limit. The difference between this fatigue limit and the endurance limit was used as a criterion of the "damage" due to

Jan 1, 1931

By Laurence C. Hicks

Consideration of the past work on the subject of the diffusion of chromium into iron suggested that additional information might be given by the use of X-ray spectroscopy in following the concentration changes through the diffusion zone. Grube and Fleischbeinl packed rods of electrolytic iron in a mixture of alumina and chromium. These specimens were heated in an atmosphere of purified hydrogen for varying lengths of time. After treatment the specimens were examined metallographically and showed the usual structure, consisting of a border of radially oriented columnar grains ending in a sharp boundary line. Reference is made to the fact that etching with certain reagents will attack only the material inside the border of columnar growth and also to the fact that polishing seems to develop a ridge at the position of the boundary between the etched and unetched areas. By chemical analysis of thin layers turned off on a precision lathe, the authors were able to obtain depth-concentration curves. These curves, reproduced in Fig. 1, show that in most cases a pronounced change of slope occurs, corresponding to the position of the boundary of the columnar grains. In a laler paper Grube extends his work to other systems which show the same characteristics.~ He concludes that the reason for the break in the curve is that a hindrance of diffusion occurs at the place where the regularly oriented grains of the diffusion zone meet the random grains of the interior portion, on the assumption that the diffusion velocity in one direction in a grain may be greater than in another direction, and that the grains in the diffusion zone orient themselves so as to give the maximum diffusion rate. Kel1ey" points out that Grube has failed to note that the boundary line does not consistently cross all grains and

Jan 1, 1934

By Jack A. Simon, M. E. Hopkins

GENERAL GEOLOGY Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which differential movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas

Jan 1, 1981

By Raymond B. Ladoo

ABRASIVES include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean or otherwise remove solid material, usually by rubbing action but also by impact (sandblasting, for example). They do not include abrasive tools-for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical action polishes and cleaners may also contain solid abrasives; for example, many metal polishes. GENERAL CONSIDERATIONS The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded grain abrasives such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example, in garnet for sandpaper, neither highly cleavable or friable grains nor extremely tough grains

Jan 1, 1949

By Harrison Schmitt

The definitions of the terms commonly used in connection with metamorphism at elevated temperature near igneous contacts are re-examined. As the study of tactite zones associated with igneous contacts progresses, more and more emphasis is put on the localization of the ore by structural forms. The generally early age of the silicates and late age of the sulphides is well established. Postsilicate structural deformation is likely to localize ore bodies. The silicates are often replaced by the ore minerals. we may not be far from proving that the elements involved in the formation of silicate aureoles are merely normal "volcanic" emanations, that silica, lime, magnesia, and alumina, and probably soda and potash, are likely to undergo local transfers only. The work of Newhouse suggests the agents of the formation of sulphides in deposits of various classifications are the volcanic emanations. Introduction The purpose of this paper is to define the terms commonly used in connection with the subject, to briefly review and discuss the broad features of the aureoles, to indicate some of the features lately recognized: to discuss the genesis, and to suggest how the associated ore deposits can best be studied and developed. When developing a subject in mining geology one is soon conscious of the vast amount of pertinent literature and that most relevant ideas, no matter how obscure, have been considered. One can only hope to make some small contribution in point of view, a few confirmatory observations, or, perhaps, suggest a small new idea indebted to the most recent data. It is nearly impossible, also, to give specific credit, and adequate credit, to all the contributors to a given subject. This study, furthermore, was not intended to cover the field exhaustively, nor is the bibliography complete. Definition OF Terms There is much confusion in the use of the broad terms concerned. Needless to say, metamorphism means change of form; metasomatism, change of substance. The term contact metamorphism, however, has been widely misused possibly by a majority of economic geologists and engineers. As originally adopted by European investigators it meant changes effected largely by heat (thermal effects) in the rocks invaded by plutonic intrusives, but did not include those local changes usually at the immediate contact brought about by the addition of substance, i.e., by metasomatism. The term has become clouded. In Europe it has

Jan 1, 1949

By I. H. Pratt

The results of a study on the preparation of thin-film capacitor structures are discussed. The dietectric source material was quartz which was sputtered and deposited onto aluminum electrodes and counter-electroded to complete the metal-oxide-metal structures. This configuration was utilized to evaluate the dielectric, the device characteristics, and related process parameters. The effect of gas sputtering pressure, magnetic field strength, source-to-substrate distance, and power density on the rate of deposition is shown. Increased film thickness uniformity over a 3 by 3 in. area by optimum substrate positioning is indicated. Dielectric constant, dissipation factor, dielectric breakdown strength, insulation resistance, heat treatment, capacitance, and dissipation over the range 400 Hz to 5 MHz are reported. In the fabrication of silicon-integrated circuits, silicon dioxide has found use as a material suitable as a diffusion mask, for surface passivation of the silicon, and for protection of conductive films used for interconnections. Its use as a dielectric for thin-film capacitors in film hybrid circuits has been limited, to a degree, for lack of a compatible processing technique and because of its relatively low dielectric constant. With the recent advent of practical metal-oxide-semiconductor (MOS) field effect devices, the material is now being used to insulate the gate electrode from the conducting channel in the silicon. In this latter application, more stringent requirements have been imposed on .the oxide. A comprehensive resume of the use of silicon dioxide in integrated silicon device technology has been compiled including oxide film and bulk properties, method of oxide formations, and their applications.' A relatively new process to deposit SiO, and other dieIectrics is by rf sputtering, and the purpose of this paper is to describe the behavior of capacitors fabricated with a dielectric which has been sputtered from a quartz target and to indicate the relative effect of several of the process parameters on the film deposition. Work on rf sputtering of SiO2 and other dielectrics has been reported utilizing a triode type of sputtering system as described herein or a diode self-sustained glow discharge system. 2-8 SPUTTERING The process occurs during an electrical discharge in a gas plasma which provides the ions for acceleration to the target to produce the desired sputtering. The necessary plasma can be generated by a dc glow discharge through application of a high potential between two electrodes at approximately 2 to 10 x 10-2

Jan 1, 1969

By N. Brown, H. Green

The effect of quenching temperature and of aging temperature and time on compression stress-strain curves of ß brass was investigated. Age softening occurs at a rate which decreases with decrease of quenching temperature below the critical temperature for ordering. The activation energy for softening is 15,400 cal per mol. No matter how rapidly brass is quenched or what the temperature from which it is quenched, practically complete order is obtained at room temperature. It has been demonstrated that with respect to the specific heat,',' electrical resistivity," X-ray diffraction, and microstructure, the slowly cooled and rapidly quenched specimens are the same and that complete long range order exists in both cases. However, Smith" showed that the hardness of ß brass depended upon the cooling rate and the temperature from which brass is quenched. Smith showed that the hardness was a maximum for specimens quenched from about 445 °C and that the as-quenched structure softened at room temperature at a rate depending upon the temperature prior to quenching. This softening after quenching is in this paper referred to as age softening. The results of this investigation are qualitatively the same as the findings of Smith. However, a more detailed analysis of these phenomena has been possible since the stress-strain curve offers a more sensitive index of the state of the metal than hardness. It is the purpose of this paper to show how the mechanical properties are related to the ordering of ß brass. A 200-lb ingot made from electrolytic copper and electrolytic zinc was extruded to 1/2in. rod. Chemical analyses at frequent intervals along the rod showed that the alloy contained 51.5 pct Cu with the greatest impurity being iron, at 0.01 to 0.001 pct. To obtain a constant test material, the 1/2in. extruded rod was warm-rolled to % in. diameter at 200°C and then recrystallized to a grain size of 2.0 mm. The specimens for the compression test were % in. high and % in. in diameter. The specimen ends were polished on 600 metallographic paper and coated with Molykote for a lubricant. The compression rig consisted of an anvil resting on the machined table of the Baldwin Southwark testing machine and a plunger fixed to the movable cross

Jan 1, 1954

By Eric S. Cheney

Sulfur isotopes are best used in conjunction with other geological studies to determine the origin of known deposits; concept-oriented exploration programs can then be developed to find similar deposits. Geochemical processes are capable of causing different S '41S" ratios in the minerals and fluids participating in natural reactions. Because the magnitude of the resultant isotopic difference is inversely proportional to temperature, sulfur isotopic studies can be used to determine the source of the sulfur in high temperature deposits. The narrow spread of sulfur isotopic values from ores related to cupolas of felsic intrusions suggests that the sulfur in the ore-forming fluids was derived from a fairly uniform source (such as the intrusions) rather than by heated ground water from the adjacent country rocks. However, geologic and isotopic evidence suggest that the sulfur of many nickel sulfide ores may have been derived from the country rocks rather than the associated mafic igneous rocks. This sulfurization hypothesis implies that mafic intrusions in sulfur-rich country rocks should be prime exploration targets. Sulfur isotopic analyses of sulfides in the mafic rocks may indicate whether sulfurization has occurred. In equilibrium geochemical reactions S" is concentrated in the minerals with the greater bonding strengths. Thus the isotopic compositions of coprecipitated sulfides that have not undergone exsolution may be used as geothermometers and to distinguish multiple periods of mineralization, post-ore metamorphism, etc. The sulfur isotopic compositions of coexisting sulfides at Butte, Mont., indicate that the copper minerals did not originate by simple replacement of pyrite. Geologic and isotopic evidence suggest that the mineralogical and isotopic zoning at Butte formed almost isothermally during the geochemical evolution of the ore-forming fluids upward and outward from the Central zone. Unidirectional reactions cause enrichment of S" in the products. At low temperatures the isotopic effects of bacterial and inorganic reactions are difficult to distinguish. Anaerobic sulfate-reducing bacteria apparently were responsible for the sulfur of Gulf Coast salt domes and for diagenetic pyrite in sandstone-type uranium deposits. Sulfur (and carbon) isotopic data suggest that the roll ore bodies of sandstone-type uranium deposits originated by limited inorganic oxidation of diagenetic pyrite rather than by bacterial activity. Accordingly roll ore bodies should be most numerous and thickest against those portions of the sandstone aquifer that contain pre-ore pyrite.

Jan 1, 1975

By Harrison Schmitt

The definitions of the terms commonly used in connection with metamorphism at elevated temperature near igneous contacts are re-examined. As the study of tactite zones associated with igneous contacts progresses, more and more emphasis is put on the localization of the ore by structural forms. The generally early age of the silicates and late age of the sulphides is well established. Postsilicate structural deformation is likely to localize ore bodies. The silicates are often replaced by the ore minerals. we may not be far from proving that the elements involved in the formation of silicate aureoles are merely normal "volcanic" emanations, that silica, lime, magnesia, and alumina, and probably soda and potash, are likely to undergo local transfers only. The work of Newhouse suggests the agents of the formation of sulphides in deposits of various classifications are the volcanic emanations. Introduction The purpose of this paper is to define the terms commonly used in connection with the subject, to briefly review and discuss the broad features of the aureoles, to indicate some of the features lately recognized: to discuss the genesis, and to suggest how the associated ore deposits can best be studied and developed. When developing a subject in mining geology one is soon conscious of the vast amount of pertinent literature and that most relevant ideas, no matter how obscure, have been considered. One can only hope to make some small contribution in point of view, a few confirmatory observations, or, perhaps, suggest a small new idea indebted to the most recent data. It is nearly impossible, also, to give specific credit, and adequate credit, to all the contributors to a given subject. This study, furthermore, was not intended to cover the field exhaustively, nor is the bibliography complete. Definition OF Terms There is much confusion in the use of the broad terms concerned. Needless to say, metamorphism means change of form; metasomatism, change of substance. The term contact metamorphism, however, has been widely misused possibly by a majority of economic geologists and engineers. As originally adopted by European investigators it meant changes effected largely by heat (thermal effects) in the rocks invaded by plutonic intrusives, but did not include those local changes usually at the immediate contact brought about by the addition of substance, i.e., by metasomatism. The term has become clouded. In Europe it has

Jan 1, 1949

By H. J. Stehli

The first sintering of zinc ores was done at the Bartlesville plant of the National Zinc Co., under the auspices of the late Otto Rissman. Mr. Rissman, who had had a long experience in the treatment of zinc ores, well realized all the difficulties of satisfactorily roasting zinc concentrates, which were becoming finer and dustier as each year went by—thus increasing the difficulties of roasting them in the existing forms of roasters, which were furnaces of the Ropp, Hegeler or similar types. Mr. Rissman's idea of the advantages of sinter was expressed in this way: in a zinc ore dead-roasted in a mechanical furnace there are many particles that are just like an egg; that is, they have a hard and impervious film of fused material on the outside, and in the retorting this completely cuts off access of the reducing gases to the center of the egg until a temperature has been reached at which this shell of the egg can be broken down through fusion. A particle of sintered zinc sulphide, on the contrary, is exactly like a piece of sponge. The moment the retort reaches the temperature at which the reactions can take place, they begin, because the reducing gases have ready access to the interior of the particles by means of the pores of the '" sponge." His faith in the advantages of sinter was amply borne out by the results obtained at the pioneer sintering plant for zinc ores installed by the National Zinc Company. Early Method of Sintering The method of procedure at Bartlesville was to roast the zinc concentrates down to somewhere in the neighborhood of 8 per cent residual sulphide sulphur; to cool these, then to wet them down to the proper moisture and mix them in the mixer of the sintering plant; then to sinter them by means of the heat available from the residual sulphides. The sulphur contents of the roast varied considerably, of course, as it was difficult with the furnaces in use to control the roasting exactly at any point short of dead roast. Hence at times the concentrates were roasted a little too low to sinter readily, and at such times the lack of sulphur was made up by the addition of raw concentrates to the sintering-machine charge in suitable amount.

Jan 1, 1937

By F. V. Lenel, M. V. Rose, A. B. Backensto

WHEN aluminum-flake powders are compacted and hot pressed and the resulting compacts are extruded or hot forged, a group of materials with unique properties is obtained. Not only do they exhibit high room-temperature strength of the order of some of the aluminum alloys, but they maintain this strength even after prolonged heat treatment at temperatures up to 900°F. Moreover, their strength decreases much less with increasing temperature than that of aluminum alloys of comparable room-temperature properties. Irmann,'" who discovered and first described this group of materials, which was called SAP, showed that the room-temperature mechanical properties of the extrusions are a function of the oxide content of the powders and therefore the oxide content of the extrusions. The higher the oxide content, the higher are their tensile strength, yield strength, and hardness, and the lower their ductility. Lyle" investigated the relationship between mechanical properties at elevated temperature and oxide content in the course of the development work of the Aluminum Co. of America on materials, called APMP, similar to those developed in Switzerland. He found that at 600 °F, just as at room temperatures, tensile strength and yield strength increase and elongation decreases with oxide content. A careful study of his data (Fig. 3, loc. cit.) shows, however, that the scatter is more pronounced than at room temperature. Gregory and Grant's data on the creep5 and stress-ruptureb roperties of the one commercial grade of the Swiss SAP and the various grades of APMP indicate that creep strength and stress to rupture also generally increase with increasing oxide .content. Ever since this new group of materials was discovered, attempts have been made to explain the mechanism by which they obtain their high room-temperature and particularly their elevated-temperature strength. In most of the attempts the new material was considered as a dispersion of aluminum oxide particles in a matrix of aluminum. Ir-mann, Von Zeerleder, and Rohner' applied a theory on dispersion strengthening developed by Rohners to the flake-powder extrusions. According to this theory the elastic limit S, of a dispersion would depend upon the average distance between the dispersed particles L according to the equation: 2 E ¦ a where E is the modulus of elasticity and a the distance between nearest neighbors in the lattice of the matrix material. Irmann and co-workers assumed

Jan 1, 1958

By M. H. Richman, L. M. Markowitz

MUCH of the available information on which the heat treatments of a particular steel are based is found in the isothermal-transformation diagram. Such is the case despite the fact that the usual thermal treatments involve continuous transformations, i.e., transformations which occur on cooling, rather than isothermal transformations. This rather unusual practice is continued because of the abundance of published isothermal-transformation diagrams1, 2 which are relatively easy to determine experimentally as compared to continuous-transformation diagrams.3, 4 However, this can easily lead to the production of improper micro-structures and may not allow full advantage to be taken of the inherent hardenability of a steel. A mathematical method of estimating the continuous-transformation diagram from the available isothermal data was developed by Grange and Kiefer;5 but, due to the mathematical approximations required in the calculations, the computation of continuous-transformation diagrams has been limited to individual cases and no large-scale compilation of these diagrams is available. With the present availability of high-speed digital computers, the problem of time-consuming approximations may be minimized and continuous-transformation diagrams may be constructed with the insertion of isothermal data into a basic program. It is the purpose of this report to announce the availability of such a program and compare the computed and experimental continuous-transformation diagrams for two different steels. Let us first review the method of Grange and Kiefer5 and then compare the results of the machine calculations with the experimentally determined diagrams. In order to apply this method, one requires the isothermal-transformation diagram and a set of curves representing cooling at constant rates. A section of an isothermal-transformation diagram is shown in Fig. 1 together with a cooling curve of M0F per sec. The cooling curve is constructed to start from the A1 (eutectoid) temperature if the transformation product is the eutectoid microconstituent (i.e., pearlite or bainite), from the A3 temperature if the product is primary ferrite, or from the 4, if it is proeutec-toid cementite. The cooling curve in Fig. 1 intersects the curve representing the start of isothermal transformation at a point A' corresponding to a temperature TX and a time fX. An arbitrary lower temperature To (on the

Jan 1, 1968

By KAGAN BENZESIK, OMUR CAN ODABAS, SELCUK KAN, Onuralp Yucel

In this study, domestic molybdenum disulfide (MoS2) concentrate was roasted in a chamber furnace and then in a rotary kiln. The behavior of the roasting process was examined in both furnaces, and which type of furnace is more advantageous to use in mass production was investigated. It is theoretically possible to roast in a chamber furnace, but a major problem was observed when the amount of concentrate was increased in the chamber-furnace experiments. The problem was solved by using a rotary kiln. This study improves the understanding of the roasting of  MoS2 concentrate and presents a different perspective to the industry, showing that rotary kilns can also be used for roasting.

By Hermann Wedding

I ASK your permission to speak about a matter which is not of a specifically scientific nature, but more of a general-I might even say of an international-nature, and the international character which this city now presents must be my justification for introducing it. The Germans, very often, are thought to be an exceedingly warlike people, but I come to-day in the capacity of a peacemaker. Our German language is an original language; it is, therefore, a language in which it is impossible to change the meaning of a word at will. It may be, perhaps, easier in a combined language, as the English, to associate and to exchange meanings. Now, a word which we hear a great deal at the present day, is "Stahl," in English, "steel." This word means, in the German language, a substance which can be hardened. As the German literature, in relation to metallurgy, is the oldest of the modern world, this circumstance may give the German a right to ask for consideration. But I think, now, when the four languages, German, Swedish, French, and English, compete in rich metallurgical literature, it is very necessary to have uniformity in the nomenclature of iron, which would prove not only useful for science, but equally so for trade. For that purpose I propose to make the divisions of iron so that the word steel shall comprise a subdivision and not a primary division as formerly. Nature furnishes us iron mostly in the state of oxides, and if in any other condition, we must convert the ore into oxide before we can make iron. The oxides are always mixed with certain earthy substances called rock or gangue. The extraction of iron involves, therefore, the twofold process of the reduction of the iron, and im¬parting to it the amount of carbon necessary for technical purposes, and the separation of the reduced and carburized iron from the gangue. The reduction is always effected by carbon or carbonaceous substances (coke, anthracite, carbonic oxide, etc.), and the result is, according to the degree of heat employed, either malleable iron or a non-malleable iron. The process of making malleable iron in this way is called, generally, the direct process-in German, Rennarbeil. It produces the iron in a solid state with a fluid cinder. By this process our ancestors made all their iron, and it has been revived in various ways in modern times up to the process of Mr. Blair, so far as I know, always without commercial success. The

Jan 1, 1877

By Hermann Wedding

I ask your permission to speak about a matter which is not of a specifically scientific nature, but more of a general—I might even say of an international—nature, and the international character which this city now presents must be my justification for introducing it. The Germans, very often, are thought to be an exceedingly warlike people, but I come to-day in the capacity of a peacemaker. Our German language is an original language; it is, therefore, a language in which it is impossible to change the meaning of a word at will. It may be, perhaps, easier in a combined language, as the English, to associate and to exchange meanings. Now, a word which we hear a great deal at the present day, is "Stahl," in English, "steel." This word means, in the German language, a substance which can be hardened. As the German literature, in relation to metallurgy, is the oldest of the modern world, this circumstance may give the German a right to ask for consideration. But I think, now, when the four languages, German, Swedish, French, and English, compete in rich metallurgical literature, it is very necessary to have uniformity in the nomenclature of iron, which would prove not only useful for science, but equally so for trade. For that purpose I propose to make the divisions of iron so that the word steel shall comprise a subdivision and not a primary division as formerly. Nature furnishes us iron mostly in the state of oxides, and if in any other condition, we must convert the ore into oxide before we can make iron. The oxides are always mixed with certain earthy substances called rock or gangue. The extraction of iron involves, therefore, the twofold process of the reduction of the iron, and imparting to it the amount of carbon necessary for technical purposes, and the separation of the reduced and carburized iron from the gangue. The reduction is always effected by carbon or carbonaceous substances (coke, anthracite, carbonic oxide, etc.), and the result is, according to the degree of heat employed, either malleable iron or a non-malleable iron. The process of malting malleable iron in this way is called, generally, the direct process—in German, Rennarbeit. It produces the iron in a solid state with a fluid cinder. By this process our ancestors made all their iron, and it has been revived in various ways in modern times up to the process of Mr. Blair, so far as I know, always without commercial success. The

By Edward S. Cook

For several years past, dating particularly from the days of serious "ore-dirt" complications at the Warwick furnace, I have been desirous of providing some safe, quick and easy method of relieving the tuyeres of slag, when the cinder- and iron-notches are chilled through loss of heat in the clucible or when, from dropping or jumping of stock, the molten slag is forcibly driven into the bellyand leg-pipes. Various methods were proposed, but objections of one kind or another always presented themselves, and the subject was postponed to a more convenient season. In the summer of 1887, while running on anthracite alone, 1 found the various expedients in use to be so utterly valueless, that the importance of a practicable tuyere slagging-valve impressed me more forcibly than ever. The holes left in the cast-iron jacket at one side of the bottom of the water-blocks were found to be of no value whatever. The swinging or hinged cap on the elbow of the belly-pipe, while convenient to permit the removal of lag after the belly-pipe was partially or wholly filled, could not be adapted to discharge the slag before solidifying, except at great risk to the men and loss of time just when the constant running of the engine and the keeping of blast on the furnace was of the utmost importance. By removing keys from the caps and holding them in place with props, the slag could be discharged through the tuyeres and belly-pipes, with the engine running, by knocking the props away at a given signal. This method is extremely hazardous to life and limb, and I have always hesitated to make use of it. When the furnace is in such condition as to require the adoption of some method of the kind, the stoppage of the engine, cooling the blast and the contents of the crucible, always aggravates the trouble. When the caps are blown open and the slag is discharged by removal of the props, it is necessary to stop the engine to replace them. An hour or more will elapse before this can be done, as the slag must be partly removed before the tuyeres can be approached by ordinary mortals, and the caps handled and fastened in place again. Any movement of the stock is liable to burn the workman, as he stands, securing the cap in front or at one side of the open belly-pipe.

Jan 1, 1889

By Howard C. Dunkle

Various factors can affect the quality of B1112 and B1113 steel as produced in a bessemer plant; among them: vessel-charging practice, blowing practice, ingot-pouring practice, ingot delivery-time practice, pit-heating practices, and ingot-rolling practice. Evaluation of the influence of ingot delivery time on quality has been chosen as the subject for this paper because this time is completely within the control of the operator, and on this particular factor there is a tremendous amount of information in the dusty archives of the average steel plant. In order to know how much improvement can be made and when attention should be directed to other factors that influence quality, in the continual struggle for improvement, the effect of ingot delivery time must be accurately evaluated. Once this is done, the importance of other variables can be accurately obtained, thus eliminating the necessity of resorting to opinions that are of doubtful value at best. In the study described herein, extensive use was made of the statistical card system as a method of determining the effect of ingot delivery time as a quality factor in bessemer screw-stock grades by simple direct correlation. The value of this statistical method as a means of accurately determining the influence of various factors has been amply demonstrated by Work1 for the bessemer process and by Hand and Gould2 and Fetters and Chipman3 for the open-hearth process. The quality records of 300,000 tons of bessemer screw-stock billets were used in this study of the effect of ingot delivery time on the rejections for breaks, pipe, check and seams. The reduction in the number of rejections for poor quality reduces the costs and increases the productivity per man-hour. The operator today, more than ever before, must know how to keep costs down, how to do it most quickly and in the best way, and how to obtain the highest quality in line with the ever increasing demands of the customer. It is necessary for him to know the individual relations and interrelations between various factors affecting the quality of the manufactured product if he is to produce material that will meet competitively the cost, performance, and quality demands of the trade. SIGNIFICANCE OF STEEL MANGANESE, MIXER SILICON AND STEEL SULPHUR AS QUALITY FACTORS In order to obtain the highest grade of material it is necessary to control many factors-not just one or two, as operators

Jan 1, 1945

By David L. Holt, Walter A. Backofen, Anwar-ul Karirn

ANNEALING the binary alloy, Mg-0.5 wt pct Zr in a hydrogen atmosphere results in extensive precipitation of zirconium hydride. The morphology of these precipitates has already been investigated.lm3 Squires, Weiner, and phillips4 found, following creep testing of the hydrided alloy at 450" and 500°C, that hydride denuded zones formed along grain boundaries that were aligned approximately normal to the tensile axis. Zone formation was attributed to diffusional creep by magnesium transport down the prevailing stress gradients.4'5 Recently, electron microprobe analysis by Karim, Holt, and Backofen6 showed the zones indeed to be zirconium-free and furthermore it was shown that in compression, zones formed along boundaries approximately parallel to the stress axis. Thus it was confirmed that the zones are formed by diffusional creep. Typical zone-formation is shown in Fig. 1. Karim, Holt, and Backofen also measured the con- tribution to the total strain, from diffusional flow, slip creep, and grain boundary shear: results showed that diffusional strain tends to saturate with increasing imposed strain, while grain boundary shear eventually becomes the dominant deformation mode. It was suggested in explanation that the precipitate-denuded zones are soft and easily sheared, such deformation contributing to the grain boundary shear measurement. A point to be emphasized is that the Mg-0.5 Zr alloy was not superplastic for the index of strain rate sensitivity of flow stress, m = a log log 6 was only 0.25. It was recognized that diffusional creep in a poly crystalline aggregate must be accompanied by boundary shearing.' The suggestion was that the non Newtonian-viscous character of diffusional creep in the Mg-0.5 wt pct Zr alloy is due to resistance to sliding of boundaries lying approximately parallel to the tensile axis.= The work described in the present note should be seen against the above background for it represents initial efforts to observe in a similar way diffusional creep in a superplastic alloy. Previous work with the ternary-alloy Mg-6 Zn-0.5 Zr, pellet extruded, showed it to be superplastic however it does not contain resolvable precipitates to act as internal markers for diffusional creep. Also the fine grain size of the alloy (0.5 p) made conventional metallography rather difficult. Solubility relationships in the Mg-Zn-Zr system are not well known, however making reasonable guesses about the probable phase diagram of the ternary, Mg-Zn-Zr, various heat treatments were attempted to produce hydride precipitation. Finally a 16-hr anneal at 495' in hydrogen was found to pro-

Jan 1, 1970

By Ehsan Vahidi, Fereshteh Rashchi, Amirhossein Shahnazi

"The pig iron from steel manufacturing plants contains a high concentration of vanadium-bearing materials smelted with iron ore. During the oxidation process of the molten pig iron with oxygen lances, vanadium transfers to the slag. In this research, recovery of vanadium from LD (Linz-Donawitz) converter slag of steelmaking plant was investigated. The leaching residue was characterized by XRD and XRF techniques. The maximum vanadium recovery was achieved at optimum leaching conditions of 70 °C, S/L: 1/15, sodium hydroxide concentration: 3 M and leaching time: 150 minutes. The dissolution rate increased with rising sodium hydroxide concentration and temperature and decreasing particle size. The experimental data are treated graphically to explain the kinetics of the vanadium recovery process using shrinking core model (SCM). As a result, the controlling regimes in the SCM were analyzed separately using liquid film diffusion control, solid product diffusion control, and reaction control mechanisms.IntroductionVanadium is commercially important as a constituent of several alloys and catalysts. Nowadays, vanadium is mostly recovered as a by-product from secondary sources or from industrial waste streams such as titaniferrous magnetite, fly ash, spent catalysts, and petroleum coke. Steelmaking operations are specifically concerned by this problem due to the production of a huge quantity of by-products [1]. These by-products, including LD converter slag, sludge, fly ash, spent catalyst, ash, and alloyed scrap, contain a notable amount of heavy metals which may cause environmental problems. Solvent extraction is one of the techniques being increasingly used for the recovery of vanadium [2]. Apart from vanadium ore, secondary resources such as titanmagnetite, ilmenite and slag from the ferrous industry are a major source of supply. The pig iron from steel manufacturing contains a majority of vanadium-bearing materials smelted with iron ore. In a heat resistant shaking ladle the molten pig iron is oxidized with oxygen lances, causing the vanadium to be transferred to the slag. Normally, the vanadium in LD converter steel slag (coming from Linz-Donawitz steelmaking process) is ca. 5% as vanadium pentoxide (V2O5). This slag is the world's principal raw material for vanadium production [3, 4]. Moskalyk and Alfantazi [4] reported that a roast-leach process is used in South Africa for the production of vanadium oxides from magnetite ores while some of the slag was converted to ferrovanadium. A portion of the slag was exported to Europe for the production of vanadium oxide. The researchers mentioned that alkaline roasting was the main process at that time employed to extract vanadium pentoxide from vanadium slags."

Jan 1, 2012