Search Documents

By J. H. Slater

There is nothing particularly new about the use of sinter in a blast-furnace burden. For many years flue dust has been sintered at the various blast-furnace plants to put it in a form that could be recharged to the furnace with some assurance that it would stay in the second time. This paper is not a compilation of scientific data but only an attempt to give our experience with sinter. There are some unexplained discrepancies in the tests given here, such as the flue dust produced and iron tonnages, but the results given are the results that were obtained. Sinter is not the cure-all for blast-furnace problems. A good coke is still the most important factor in good furnace operation. However, good sinter is a big help. As flue dust is produced under varying operating conditions and fluctuates greatly in carbon content, it is difficult to produce from flue dust alone a uniform sinter, which will give satisfactory blast-furnace results. Sinter made from flue dust alone will change in character with every carbon variation. Almost invariably flue dust contains carbon in excess of the amount necessary to make good sinter, and this excess must be burned out. This, of course, necessitates reduction of the speed of the sintering machine and thus a decrease in tonnage. An alternative is to dilute with a carbon-free material to use up the excess carbon. High-carbon material when sintered results in a very dense, undesirable product, since the excess heat melts the charge into a hard, nonporous mass, and tends to form refractory silicates. At the Republic Steel plant in Cleveland, there had existed since 1924 a continuous-type sintering machine having 224 sq. in. of grate-bar area, capable of producing 9 to 11 tons of sinter per hour from flue dust. Under a former management, it was the practice to sinter only the flue dust from the blast furnaces, no attempt being made to recover the gas-washer sludge. As the dust was limited, the plant operated only part time. In other words, there was a sintering plant representing considerable investment, with good facilities for screening and preparation of raw materials, and flue dust available for only part-time operation. The sinter produced was costly and not a very desirable product. The first step was to install equipment for the recovery of the gas-washer sludge. This was done in the form of two large thickeners and a filter, which have proved very satisfactory. It was then decided to screen out the minus 3/8-in. fines from the Mesabi ores, mix them with flue dust and coke breeze when necessary, and operate the plant at full capacity. The tonnage increased to 18 tons per hour and the product was much improved. Sintering costs fell and the product was a preferred blast-furnace material, which on an iron unit cost compared very favorably with good Mesabi ores. On the average, 40 per cent flue dust and 60 per cent fine ore was being used. The oversize from the ore screening also became a preferred product for the

Jan 1, 1941

By C. E. Sims

In some experimental work conducted several years ago, it was noted that sulphur seemed to have a distinct influence on grain size of carbon steels. 111 order to check this observation, a series of S..A.E. 1040 steels was made with the normal composition held as nearly constant as possible. The steels were made with three sulphur levels, which were 0.012, 0.024 and 0.038 per cent sulphur, respectively. For each of the sulphur levels, steels were made with only silicon deoxidization and with aluminum additions of 0.1015, 0.025, 0.050 and 0.10 per cent. The melting medium was an acid-lined high-frequency induction furnace. These steels were forged and rolled and differentiall!. quenched from temperaturcs in the range of 1500O to 1800°F. After this, the A.S.T.M. grain size was determined and plotted as in Fig. I. It will be noted, first of all, that the aluminum-free steels had filler grain size with higher sulphur when heated to 1500, but that this condition was reversed at 1700°. When aluminum was added to produce fine grain size, the steels in the lowest sulphur level were fine-grained only to 1600°. and then only with an addition of one pound of aluminum per ton. The medium sulphur steels werc fine-grained to 1600' with a wider range of aluminum addition. The steels in the highest sulphur level were fine-grained at 1600° over a still wider range of aluminum additions and fine- grained at 1700° with an addition of one pound per ton. Fig. 2 shows curves of the grain-coarsening temperature for these steels and illustrates how sulphur and aluminum combine to give greater inhibition to grain growth than aluminum alone. Only the highest sulphur steels have a grain-coarsening temperaturc above 1700°.. At 1650°, the low sulphur steel is fine-grained only at its peak, while the highest sulphur steel is fine-grained over a wide range. In these tests, one pound of aluminum per ton gave the best results; this is equivalent to about 1 1/2 lb. per ton for commercial condition. IllcQuaid-Ehn tests made on these steels showed the same trend but to a lesser degree. The tests were repeated on a series of S.A.E:. 1015 steels with sulphur levels of 0.02 and 0.03j per cent. Aluminum additions were made in the range from 0.025 to 0.15 per cent. These steels were forged and rolled, normalized at 2000°F. to put them all in the same starting condition, then reheated to various temperatures from 1600" to 1800" and cooled at rates that would allow ferrite precipitation in the austenitic grain boundaries. The results of these tests arc shown in Fig. 3. It will be noted that. up to the temperature of 1650°, there is very little difference in the grain size obtained from the two levels of sulphur. .At temperatures of 1700° and 1750°, however, the lower sulphur steel was fine-grained only with an aluminum addition of 1 1/2 lb, per ton;

Jan 1, 1945

By Nicholas J. Grant, Italo S. Servi

SPECIAL polishing and etching techniques were developed during an investigation of the high temperature mechanical properties of high purity aluminum (99.995 pct Al).* Electrolytic polishing was done successfully in the following electrolyte: 5 ml perchloric acid (72 pct), and 95 ml glacial acetic acid. No special precautions need be taken during the preparation of the electrolyte since no appreciable heat of mixing is evolved. Although the electrolyte is not an explosive, it is recommended that Jacquet's safety rules' be followed during the polishing operation. A voltage of 25 to 60 v gives a good polish in about 2 min at room temperature after preparation on 3/0 metallographic paper. Most of the grain boundaries are visible under the microscope after polishing. Since the current is controlled essentially by the resistance of the bath, it is necessary to keep the anode-to-cathode distance as constant as possible. Accordingly, polishing of irregularly shaped pieces will be difficult. A cooling bath and a stirring system are advisable in order to keep the temperature of the bath uniform and constant. Coarse-grained samples can be macroetched in a few seconds by lowering the voltage below 10 v. This is done after electrolytic polishing, without removing the sample from the bath, Fig. 1. The specimen can be repolished in less than 1 min by raising the voltage above 25 v. The "galvanic etching" technique, which has been described elsewhere,' was found to be helpful not only for macroetching, but also for microetching coarse-grained specimens. In fact, the different orientations of adjacent grains provide good contrast at the grain boundaries, when the sample is observed under polarized light. If the specimen is only partially etched, Fig. 2a, the grain boundaries can be located without completely destroying the appearance of the surface of the specimen. The unetched surface appears black under polarized light. Excellent color contrast is obtained by using a "sensitive tint" plate in the optical system of the microscope. In this case, the unetched surface has a magenta color, while the etched part of the sample assumes different colors varying from green to brown, according to the orientation of the grains. Etch pits were produced on high purity aluminum by using the technique suggested by Lacombe and Beaujard." Good results also were obtained by substituting 70 pct nitric acid for the fuming nitric acid recommended. This gave an etching reagent of the following composition: 70 ml nitric acid (70 pct), 50 ml hydrochloric acid (37.5 pct), and 3 ml hydrofluoric acid (48 pct). An example of the results is shown in Fig- 2b. The outline of the etch pits is revealed sharply if the specimen is observed under polarized light, as shown in Fig. 2c. These metallographic techniques are not suitable for the examination of commercially pure (2s) aluminum. References 'P. A. Jacquet: Metal Finishing (Nov. 1949) 47, p. 62. 21. S. Servi: Metal Progress (1950) 58, p. 732. 3 P. Lacombe and L. Beaujard: Journal Inst. of Metals (1947) 74, p. 1._________________________

Jan 1, 1952

By A. A. Burr, D. Caplan

IN carrying out experiments in metal-gas systems, it is often difficult to estimate how long a reaction period must be allowed for equilibration. This is especially true in systems for which the diffusion coefficient is not known. In an investigation of the Cr-O system, the necessary information was obtained in the way described subsequently. Two pieces of chromium sheet of different thicknesses were packed in mixed powders of chromium and Cr2O3 and sealed into an evacuated metal capsule by welding. Austenitic stainless steel proved suitable as a capsule material up to 1350°C and molybdenum at higher temperatures. The capsule then was heated at a specific temperature for a time sufficient to saturate with oxygen the thinner but not the thicker specimen. The time is readily estimated from a preliminary experiment if a sufficient thickness differential is chosen. Under these experimental conditions, the metal sheet is exposed to a partial pressure of oxygen equal to that of the dissociation pressure of the oxide and hence can become saturated with oxygen without developing any second phase. After cooling, both samples were analyzed for oxygen by the vacuum fusion technique. Assuming that the surface of the specimens is kept saturated with oxygen throughout the experiment, the diffusivity can be calculated by application of the appropriate solution to Fick's second law. This is most conveniently accomplished by use of a plot of mean fractional saturation (Cm-Co) / (Cs-Co) vs (Dt) ½/L as given by Darken,' where t is time, L the half-thickness of the sheet, and D the diffusion coefficient. Cm, the mean concentration at time t, is given by the oxygen percentage in the thicker specimen; Cs, the constant surface concentration, is the oxygen percentage in the thinner specimen; Co is the oxygen content of the original chromium sheet. (Cm-Co) / (Cs-Co) is calculated and the corresponding (Dt) ½/L is read from the graph and D thereby calculated. By performing the experiment at two temperatures and plotting log D vs 1/T, the D for any temperature is established. (The activation energy for diffusion may be obtained from the slope of the line.) Once D is known as a function of temperature, it is a simple matter to estimate the correct reaction time for experiments with single specimens at other temperatures by equating (Dt) ½/L to its value for effective saturation. Darken' points out that this is approximately unity. The solubility of oxygen in chromium, as determined from the thin samples at each temperature, proved to be approximately 0.03 pct at 1350°C and less at lower temperatures. Due to low solubility and to the known difficulties of the vacuum fusion method in this low range, the values obtained for D (5x10-0 sq cm per sec at 1350°C) are estimated to be correct only within an order of magnitude. Nevertheless, the method has proved useful in estimating reaction times. Its usefulness will be greater in metal-gas systems where the solubility is appreciable. A second function of the method is to permit the determination of diffusion coefficients in systems for which the conventional techniques are experimentally difficult or impossible.

Jan 1, 1956

By Floyd C. Kelly

A. HUltgren, .Söderfors, Sweden (written discussion*).—From the results obtained in his own experiments as well as those of Austin and of Grube Mr. Kelley derives a general law, expressed tentatively in the following words: "whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, a comparatively rapid, or abnormal, grain growth results." It is suggested that,, in order adequately to represent the facts, this definition should he restricted by the following qualifications: a and b are the two metals, b diffusing into a. A. At the temperature in question a should exist as phase a 1 having a limited solubility for b. B. The supply of b by diffusion should be sufficient, in view of the rate of diffusion into a 1, to increase the concentration of b above the saturation value in a 1 so as to cause a new phase a2 to form. (7. The phase a2 should have a range of solubility for 6, thus rendering continued diffusion possible. D. In order that the columnar grains may be preserved in the structure the phase a2 should, of course, not suffer transformation on cooling. The phenomenon thus defined may be described as progressive transformation by diffusion. Its mechanism would appear to he as follows: Fig. 17 shows a portion of the equilibrium diagram a-b, Fig. 18 the distribution of b in solution after various periods of diffusion, Fig. 19 represents the structure in cross-section of a cylindrical rod of a at the end of heating period 3. 1. The first effect of diffusion of b into a will be to establish a concentration gradient in phase a1 (1, Fig. 18). When the saturation value for the temperature of the experiment (m, Fig. 17) is reached at the surface, nuclei of, a2 of composition n will form here, and later develop into a continuous layer. Assuming that diffusion proceeds without irregularities and that transformation at any point sets in without lag—i. e., in the moment saturation is exceeded—the transformation a1-a2 will advance inwards on a cylindrical surface concentric with the surface of the rod. The discontinuity of composition at the transformation surface in the position it happens to have at the end of the treatment (3, Fig. 18) will be preserved at room temperature, if the cooling is not particularly slow, and be recorded in the structure as a marked, smooth line, in agreement with Grube's and the author's observations. The shape of the distribution curves in Fig. 18 is also corroborated by the analyses given by Grube. 2. During diffusion, since the secondary phase a2 is always in immediate contact with the saturated part of the primary phase a1, there should be very little lag in the transformation. This means that the first a2 grains formed should grow in preference to the formation of independent nuclei; in other words, columnar growth results. It does not seem necessary to assume, with Green,' whose conception of the phenomenon

Jan 1, 1929

Time as a Factor in the Making and Treating of Steel. By John Johnston. (Howe Lecture) (T.P. 1478) Influence of Chromium and Molybdenum on Structure, Hardness and Decarburization of 0.35 Per Cent Carbon Steel. By R. F. Miller and R. F. Campbell. (T.P. 1345) Mechanical Properties of Iron-manganese Alloys. By F, M. Walters, Jr., I. R. Kramer and B. M. Loring. (T.P. 1369) The Instability of Low-expansion Iron-nickel-cobalt Alloys. By I. R. Kramer and F. M. Walters, Jr. (T.P. 1370) The S-curve of a Chromium-nickel Steel. By B. M. Loring. (T.P. 1383) A Magnetic Determination of the A3 Transformation Point in Iron. By B. A. Rogers and K. 0. Stamm. (T.P. 1388) Rapid Tension Tests Using Two-load Method. By A. V. de Forest, C. W. MacGregor and A. R. Anderson. (T.P. 1393) Effects of Scrap in the Blast-furnace Burden. By C. L. T. Edwards. (T.P. 1270) Temperature Gradients through Composite Carbon Columns and their Application to Blastfurnace Linings. By F. J. Vosburgh and M. R. HatFIeld. (T.P. 1363) Correlations of Some Coke Properties with Blast-furnace Operation. By H. W. Johnson. (T.P. 1402) The Technical Cohesive Strength and Yield Strength of Metals. By D. J. McAdam, Jr. (T.P. 1414) Effects of Eight Complex Deoxidizers on Some 0.40 Per Cent Carbon Forging Steels. By George F. Comstock. (T.P. 1417) Significance of the Bessemer End Point. By H. T. Bowman. (T.P. 1428) Structural Diagrams of Nickel Irons and Steels. By J. T. EasE and N. B. Pilling. (T.P. 1432) Carbides in Low-chromium Steel. By Walter Crafts and C. M. OFFenhauer. (T.P. 1436) Hardenability Calculated from Chemical Composition. By M. A. Grossmann. (T.P. 1437) Recrystallization of Silicon Ferrite in Terms of Rate of Nucleation and Rate of Growth. By J. K. Stanley and R. F. Mehl. (T.P. 1438) The Solubility of Carbon as Graphite in Gamma Iron. By R. W. Gurry. (T.P. 1440) An Evaluation of the Factors Affecting Iron Oxide in the Open-hearth Bath. By J. E. Gould and H. J. Hand. (T.P. 1442) Precision in Creep Testing. By J. A. Fellows, Earnshaw Cook and Howard S. Avery. (T.P. 1443) Lattice Relationships in the Decomposition of Austenite to Pearlite, Bainite and Martensite. By G. V. Smith and R. F. Mehl. (T.P. 1459) Rate of Nucleation and Rate of Growth of Pearlite. By F. C. Hull, R. A. Colton and R. F. Mehl. (T.P. 1460) Weight Change as a Criterion of Extent of Decarburization or Carburization. By R. W. Gurry. (T.P. 1470) Observations in the Making and Use of Sulphite-treated Steels. By E. L, Ramsey and L. G. Graper. (T.P. 1476) Diffusion in Metal Accompanied by Phase Change. By L. S. Darken. (T.P. 1479) Engineering Properties of Heat-resistant Alloys. By Howard S. Avery, Earnshaw Cook and J. A. Fellows. (T.P. 1480) Distribution of Manganese and of Sulphur between Slag and Metal in the Open-hearth Furnace. By L. S. Darken and B. M. Larsen. (T.P. 1481)

Jan 1, 1942

By Frank Foote, E. R. Jette

Precision lattice-constant measurements have been widely used in the study of cubic solid solutions but as yet have been rarely applied to noncubic solid solutions. (See, however, references I and 2.) With the high precision at present attainable in the measurement of lattice constants, the X-ray method should be readily applicable to noncubic solid solutions. In the work reported here, hexagonal close-packed magnesium was used as the solvent and either lead, bismuth or gold as the solute. In the magnesium-lead and magnesium-bismuth systems the a and c lattice constants were determined as a function of composition, densities were calculated from these lattice-constant data, these theoretical densities were compared with those directly measured and the solid solubility limit was determined on quenched specimens over a considerable range of temperature. In the magnesium-gold system, the solid solubility is very small but we have obtained an indirect check on the solubility limit previously reported. Materials and Preparation oF the Alloys The magnesium used was obtained from the Aluminum Company of America and was 99.987 per cent pure. Impurities as reported On the label were: Fe, Al, 0'004 per cent; Si, 0.009 per cent; Zn, trace; Cu, Pb, nil. The bismuth was Merck's analytical grade, minimum purity 99.95 per cent. Maximum impurities as listed on the label were: Fe, 0.008 per cent; Pb, 0.010 per cent; Ag, 0.010 per cent; Cu, 0.005 per cent; Sn, 0.003 per cent; Sb, 0.00; As, 0.000; S, 0.01 per cent. The gold was purified by double precipitation with sulphur dioxide. The lattice constants of these three metals have been previously reported.3 The lead used was test lead, silver free and with a maximum of 0.10 per cent heavy metal impurities. The lattice constant 01 this lead has been measured and found to be 4.94057 ± 0.00016 at 25°C. The alloys were prepared by melting together weighed amounts of the constituent metals in magnesia-lined alundum crucibles under an atmosphere of hydrogen purified by passing over magnesium heated to 500°C. The magnesia lining prevented contamination 01 the alloys with aluminum. Vacuum melting could not be used because of the volatility of magnesium. A high-frequency induction furnace was used for the melting operation and the stirring action of the current resulted in thorough mixing of the constituents. The melts were allowed to freeze in the crucible, the ingots obtained weighed about 10 grams. An extremely thin white film formed on the surface of the melts, sometimes covering only a part of the exposed surface. The ingots were filed clean, placed in small iror crucibles with close-fitting lids and indi. vidually sealed into Pyrex glass tubes Before sealing off, the tubes were alter

Jan 1, 1941

By Frank G. Norris, William C. Marshall

The term "total operation" is meant to include problems that cannot be answered from the standpoint of either the blast furnace or the open hearth separately but must be studied by considering the interrelations of these two processes. There are other ways of expressing this idea, such as reference to the blast furnace and the open hearth as an integrated process or by emphasizing the interrelation and interaction of the two processes. Much progress has been made in metallurgy and other fields by breaking complicated processes and reactions into simpler parts and studying each of these intensively. This intensive study frequently is done under the controlled conditions of the laboratory experiment. The entire process is understood better by this specialized study of each of its parts. This procedure is so satisfactory that an understanding of unit operations is a fundamental requirement of chemical engineering. Much discussion of the open-hearth process is in terms of one heat or one furnace. By this is meant that the conclusions apply to one furnace, wherever it may be. Furnaces seldom occur singly; they are located in groups and these groups are located in steel plants having characteristic blast-furnace equipment. Problems that are affected by the number of furnaces operating, by the number of blast furnaces in the plant and by the fact that the open- hearth shop is dependent on the bla furnace capacity rather than on its o needs for the amount of iron available among those which, in contrast to "u operations," we have chosen to call "to operations." Many of these problems, such as cha ing delays and the general mechani problem of material handling, are familiar that merely to define " total op ations" brings them to mind. These pr lems are of such importance that alrea they have received careful thought 2 study and probably will merit furt study. As will be shown later, these mechan problems are so intimately related metallurgical problems of total operati that the effect of certain changes cannot ascribed with certainty to either a mech ical or a metallurgical cause entirely. Although the problems coming under general term of "railroading" are inclu in the problems of total operations, ' others are selected for the discussion of paper, One of these is strictly a problem composition; the other is strictly a prob of tonnage production. The problem of phosphorus is pres whenever basic open-hearth slag is used the blast-furnace burden. This practice not secured universal acceptance chi because of difference in preference for h manganese or low-manganese pig iron hjgh-manganese (2.00 per cent) iron is to made, open-hearth slag as a source manganese is usually cheaper than m

Jan 1, 1943

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942

By R. K. McGeary, B. Lustman

Orientation relationships and rates of annealing of 97 pct cold rolled zirconium have been studied by X-ray techniques, metallography, and by hardness measurements. The process of annealing occurring by the formation of domains, and their subsequent growth without recrystallization, is demonstrated. NUMEROUS investigators1-' have revealed sub-grain formation after annealing cold worked metal single crystals and have generally described the results in terms of a dislocation mechanism of polygonization.5,6 in heavily cold rolled polycrystal-line aluminum the first stages of heating cause an apparently spontaneous subdivision of regions of the deformed matrix into a great number of slightly disoriented domains followed or accompanied by rapid growth of certain domains to form a recrystallization texture.7,8 In the present investigation the isothermal rate of annealing of cold worked polycrystalline zirconium has been studied by X-ray techniques, metallography, and by hardness measurement. It will be shown that, rather than by the usual nucleation and growth mechanism,"12 the process of annealing can best be explained by the formation of domains early in the annealing treatment and the subsequent growth of these domains without recrystallization. Experimental Procedure All the experimental work was performed on an arc-melted ingot of high purity zirconium crystal bar made by Westinghouse in a production scale deBoer unit. The weight percentage of impurities in the zirconium were as follows: C, 0.04; Fe, 0.05; Hf, 0.014; W, 0.01; Ti, Ni, and Al, 0.003; Si and N, 0.002; Cr and Cu, 0.001. Metallographically the zirconium showed only a single phase. The 4 in. diarn ingot was forged at 760°C to a 1 1/2x3 in. plate and was then rolled at 760°C to 0.150 in. thickness and annealed at this temperature for 20 min to produce an equiaxed grain structure of about 0.1 mm average grain diameter. The hot rolled plate was roller-leveled, surface ground to 0.135 in., cold rolled 83 pct reduction in thickness on a two-high mill, and then to a total reduction of 97 pct on a Sendzimir mill. The 0.004 in. strip material so produced received no subsequent mechanical treatment. Specimens % in. square were sheared from the rolled strip and isothermally annealed at 104 mm Hg in an all glass vacuum system equipped with a Vycor furnace tube. The temperature data presented are the average temperatures during the runs and did not vary more than about k3"C. X-ray Diffraction Methods: When zirconium is drastically cold rolled, a high degree of preferred orientation results in which prism poles, {1010}, are perpendicular to the rolling direction. After fully annealing this material an entirely new texture develops which corresponds to a 20" or 40" rotation of the deformation texture about hexagonal axes of

Jan 1, 1954

By B. M. Larsen, T. E. Brower

IN an earlier paper1 we discussed a simple, rapid method of taking samples of liquid steel and analyzing them for oxygen, which, though possibly not absolutely accurate (as is likewise true of all other methods), certainly yields results that are satisfactorily consistent. Accordingly, samples from hundreds of heats in different shops were analyzed for oxygen, with results sufficient in number to be handled statistically and permit estimation of some general trends. Measurements were made in acid as well as in basic open hearths, throughout the refining period, to learn how stirring, blocking, adding ore or lime or sand, affects the oxygen content of the bath; we also followed the changes brought about by tapping, teeming, and deoxidizing. Some of these results, discussed in an earlier paper.2 bring out the dominant role of the carbon-oxygen reaction in regulating degree of oxidation both of metal and of slag, also the marked variability of concentration of dissolved oxygen [0] in excess of that which would be in equilibrium with carbon and with carbon monoxide at a partial pressure of one atmosphere. As a logical beginning on this complex problem, we take up in the present paper the variability of this excess oxygen, ?[O], when other factors are as constant as they ever are in open-hearth operation; namely, toward the end of the refining period, when the bath may be regarded as in the comparatively steady state it approaches in absence of disturbing factors. This condition was chosen because by that time the significant reactions, except carbon oxidation, between slag and metal have come to substantial equilibrium; this facilitates interpretation of the complex situation and thus permits more definite conclusions to be drawn. This excess concentration of oxygen, ?[0], in the metal is needed, of course, to make the steelmaking process go at a reasonable rate; alternatively it may be regarded as a measure of the virtual pressure increment above one atmosphere, or of the degree of supersaturation, of carbon monoxide in the metal. According to our measurements, the excess concentration ?[O] in liquid steel varies from about 0.009 to 0.035 per cent oxygen by weight. It is quite sensitive to change of conditions, being altered temporarily by operations such as stirring with green poles, additions of ore, lime, or sand; but as the disturbance works itself out, it resumes a level within the intermediate range characteristic of the steady state. The conditions most common in average furnace practice are covered by the following : [ ] as in a reasonably steady state-that is, when it is boiling normally, is at proper temperature with a well-shaped slag, and has been free from disturbing effects during the preceding half hour-?[O] returns from

Jan 1, 1946

By William C. Marshall, Frank G. Norris

The term "total operation" is meant to include problems that cannot be answered from the standpoint of either the blast furnace or the open hearth separately but must be studied by considering the interrelations of these two processes. There are other ways of expressing this idea, such as reference to the blast furnace and the open hearth as an integrated process or by emphasizing the interrelation and interaction of the two processes. Much progress has been made in metallurgy and other fields by breaking complicated processes and reactions into simpler parts and studying each of these intensively. This intensive study frequently is done under the controlled conditions of the laboratory experiment. The entire process is understood better by this specialized study of each of its parts. This procedure is so satisfactory that an understanding of unit operations is a fundamental requirement of chemical engineering. Much discussion of the open-hearth process is in terms of one heat or one furnace. By this is meant that the conclusions apply to one furnace, wherever it may be. Furnaces seldom occur singly; they are located in groups and these groups are located in steel plants having characteristic blast-furnace equipment. Problems that are affected by the number of furnaces operating, by the number of blast furnaces in the plant and by the fact that the open- hearth shop is dependent on the bla furnace capacity rather than on its o needs for the amount of iron available among those which, in contrast to "u operations," we have chosen to call "to operations." Many of these problems, such as cha ing delays and the general mechani problem of material handling, are familiar that merely to define " total op ations" brings them to mind. These pr lems are of such importance that alrea they have received careful thought 2 study and probably will merit furt study. As will be shown later, these mechan problems are so intimately related metallurgical problems of total operati that the effect of certain changes cannot ascribed with certainty to either a mech ical or a metallurgical cause entirely. Although the problems coming under general term of "railroading" are inclu in the problems of total operations, ' others are selected for the discussion of paper, One of these is strictly a problem composition; the other is strictly a prob of tonnage production. The problem of phosphorus is pres whenever basic open-hearth slag is used the blast-furnace burden. This practice not secured universal acceptance chi because of difference in preference for h manganese or low-manganese pig iron hjgh-manganese (2.00 per cent) iron is to made, open-hearth slag as a source manganese is usually cheaper than m

Jan 1, 1943

By Maria I. De Rosa

The major fire and fire injury findings for all metal/nonmetal mining categories for 1990-2001 are shown in tables 64-65. Table 66, partly illustrated in figure 22, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays for all metal/nonmetal mining categories by time period. For all metal/nonmetal operations (including stone and sand and gravel), a total of 518 fires occurred during 1990-2001; 296 of those fires caused 308 injuries and 4 fatalities (Ewhr = 4,012 x 106 hr, In = 0.015, LWD = 36,204). Thirty fires and 26 injuries involved contractors. The greatest number of fires and fire injuries occurred at surface operations; the highest risk rate values were also calculated for surface operations. The number of fires increased during the first four 2-year time periods (1990-1991, 1992-1993, 1994-1995, and 1996-1997), then decreased during the last two periods (1998-1999 and 2000-2001). The number of injuries showed a decrease throughout the periods, accompanied by an increase in employees' working hours. Twenty-five firefighting interventions by mine rescue teams in underground mines and at least 30 interventions at surface operations were required to combat these fires. However, 45 fires destroyed or heavily damaged facilities and equipment (including 19 pieces of mobile equipment) because of failure of firefighting methods, late fire detection, undetected fires, or fire size. Ninety-seven fires were detected late, and 30 fires were undetected. The ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flame (169 fires or 33% with 137 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (89 fires or 17% with 46 injuries and 3 fatalities), heat source/explosion and flammable liquids/ gas/refueling fuel on hot surfaces (98 fires or 19% with 73 injuries), electrical short/arcing (51 fires or 10% with 16 injuries), and spontaneous combustion/hot material (46 fires or 9% with 17 injuries). The flame cutting/welding spark/slag/flame source caused fires usually involving welders' clothing or oxyfuel/grease and other materials (including chute and dust collector liners, flammable liquids, belt material, crusher, hopper and shaker deck materials, washer plants, equipment mechanical components, stampler breaker, hydraulic fluid, rubber tires and hoses, gear boxes, bin feeder, dump rope cables, screen liner and screen panel, kiln and shaft material, pipelines, liquor pumps, wood pallets, electrical junction boxes, handrails, grease, refuse, shop and wood). The spontaneous combustion/hot material and electrical fires were usually detected late due to lack of combustion gas/smoke detection systems. At least 55 of the 89 mobile equipment hydraulic fluid/fuel fires became large fires (requiring 12 mine rescue team interventions in underground

Jan 1, 2004

US 4,134,618-Method for restoring an underground reservoir subsequent to the solution mining of an ore body of uranium, copper, nickel, vanadium, molybdenum, silver, rhenium, or selenium. Clean water a cycled through the mined area, via the injection and production wells used during mining, at a flow rate sufficient to entrain residual dissolved solids. The solids are separated at the surface and disposed of, e g., in a deep disposal well, while clarified water is recycled C A. Kossack, assigned to Atlantic Richfield Co. Jan 16, 1979 4 pp. (299-5) Filed. 12-29-77 (865,646) US 4,155,982-In situ leaching of a subterranean uranium ore deposit The ore is leached with a dilute aqueous solution of ammonium bicarbonate containing a small amount of hydrogen peroxide in order first to convert tetravalent uranium in the ore to the hexavalent state and second to dissolve the hexavalent uranium preferentially to the other metals or elements commonly occurring In such ore The uranium- enriched leach liquor IS brought to the surface, and the uranium recovered by means of adsorption on a particulate ion exchange resin, elution with an acid, and treatment with ammonia to precipitate relatively pure ammonium diuranate. G G. Hunkin, T P. Fife, and J R Stano, assigned to Wyoming Mineral Corp. May 22, 1979. 13 pp (423-7). Filed: 10- 9-74 (51 3,445). Same: Canadian 1,027,849, dated Mar. 14, 1978. US 4,157,847-In the mining of sulfur by the Frasch process hot water accumulating above subterranean sulfur from previous mining operations is recycled downward to contact and heat additional solid subterranean sulfur. Advantageously, pressurized and superheated drive water from above ground is commingled with the underground water to raise its temperature before it is recycled downward R. L Williams, R L Latiolais, J. L Gabriel, and R. L Bouis, assigned to Freeport Minerals Co June 12, 1979. 13 pp (299- 6) Filed 7-28-77 (81 9,879). US 4,158,76%1n this method for determining the uranium content of a solution obtained in the solution mining of an underground uranium ore deposit, the intensity of gamma radiation from the Th-234 daughter of U-238 emitted by the solution is determined as it impinges on a scintillator after being passed successively through filter foils of a ytterbium- tin alloy, a lutecium-tin alloy, and a hafnium-zirconium alloy This scintillation is evaluated as a measure of the uranium content To assure that the uranium-thorium conversion has reached a stable state, the measurement should be made about three months after the uranium solution has been produced R C Smith, assigned to Westinghouse Electric Corp. June 19, 1979 11 pp. (250-255). Filed. 10-20-77 (843,770).

Jan 1, 1980

By M. R. Hatfield, F. J. Vosburgh

IN a recent article,† it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell-to keep it cool enough for safety and comfort and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a carbon tube nominally 2 5/8 in. o.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a 15-kva. transformer operating

Jan 1, 1941

By Ladislav Bebar, Tomas Parizek, Radek Dvorak, Petr Stehlik

"More and more sweeping environmental regulations initiate research, development and introducing into operation up to date technologies for cleaning off-gas and flue gas generated in various branches of industry and municipal waste treatment. The following systems based on novel types of equipment are shown: thermal and catalytic treatment of waste gases polluted by VOC (Volatile organic compounds) and carbon monoxide (alternatively NOx), catalytic filtration for efficient destruction of PCDD/F (dioxins) and potentially NOx, wet cleaning of flue gases polluted by SO2, HCl and HF with a original type of homogenizer “O-element”, integrated equipment for cleaning waste gases polluted by solid particulates, SO2, HCl, HF and heavy metals (alternatively NOx or PCDD/F). The outstanding features of all equipment mentioned above are low investment and operating costs together with high removing efficiency of pollutants. These units can be used mainly in incineration plants, refineries and other chemical plants. The paper represents a review based on papers published in reputable international journals and a monograph under preparation as well as on experience from industrial applications.IntroductionIn the recent years, more and more emphasis is put on preserving clean environment. One of the most closely monitored objects of general public attention are exhaust gases, containing a number of undesirable compounds like NOx, CO, SO2, HCl, HF, fly ash a PCDD/F. These harmful species are created in chemical processes mainly in the industry, transport and energy sectors. There is therefore a strong impetus for abatement of these harmful pollutants. Sectors of industry are thus subject to emission regulations specific to various types of units. In the framework of increasing demand for a clean environment, the concerned legislation is becoming increasingly strict and requires removal of pollutants by modern methods that would ensure efficient abatement of emissions at reasonable investment and operating costs.Attention is focused chiefly on methods for decreasing harmful emissions from thermal waste treatment facilities processing industrial and municipal waste that may be subsequently applied in other sectors of industry. Units for the thermal treatment of waste not only provide means of its disposal, but may become also important sources of energy, provided that strict emissions limits are satisfied. Figure 1 compares emission limits given by the legislation for municipal waste incinerators and limits for a selection of energy sources with heat capacity up to 50 MW (see EU regulation 200/76/EC). The Figure implies that the values of emission limits for waste incineration are mostly comparable with emissions from the combustion of natural gas. Thanks to the continuing improvements of the methods for removal of harmful pollutants, the emissions from waste incinerators are typically deep below the limits."

Jan 1, 2008

By N. Tiner

In an article on magnesium and its alloys, Gann and Winston! stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 675°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I). This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of, these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing 0.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C. and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. Experimental Method The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942

By Frank Foote, E. R. Jette

Precision lattice-constant measurements have been widely used in the study of cubic solid solutions but as yet have been rarely applied to noncubic solid solutions. (See, however, references I and 2.) With the high precision at present attainable in the measurement of lattice constants, the X-ray method should be readily applicable to noncubic solid solutions. In the work reported here, hexagonal close-packed magnesium was used as the solvent and either lead, bismuth or gold as the solute. In the magnesium-lead and magnesium-bismuth systems the a and c lattice constants were determined as a function of composition, densities were calculated from these lattice-constant data, these theoretical densities were compared with those directly measured and the solid solubility limit was determined on quenched specimens over a considerable range of temperature. In the magnesium-gold system, the solid solubility is very small but we have obtained an indirect check on the solubility limit previously reported. Materials and Preparation oF the Alloys The magnesium used was obtained from the Aluminum Company of America and was 99.987 per cent pure. Impurities as reported On the label were: Fe, Al, 0'004 per cent; Si, 0.009 per cent; Zn, trace; Cu, Pb, nil. The bismuth was Merck's analytical grade, minimum purity 99.95 per cent. Maximum impurities as listed on the label were: Fe, 0.008 per cent; Pb, 0.010 per cent; Ag, 0.010 per cent; Cu, 0.005 per cent; Sn, 0.003 per cent; Sb, 0.00; As, 0.000; S, 0.01 per cent. The gold was purified by double precipitation with sulphur dioxide. The lattice constants of these three metals have been previously reported.3 The lead used was test lead, silver free and with a maximum of 0.10 per cent heavy metal impurities. The lattice constant 01 this lead has been measured and found to be 4.94057 ± 0.00016 at 25°C. The alloys were prepared by melting together weighed amounts of the constituent metals in magnesia-lined alundum crucibles under an atmosphere of hydrogen purified by passing over magnesium heated to 500°C. The magnesia lining prevented contamination 01 the alloys with aluminum. Vacuum melting could not be used because of the volatility of magnesium. A high-frequency induction furnace was used for the melting operation and the stirring action of the current resulted in thorough mixing of the constituents. The melts were allowed to freeze in the crucible, the ingots obtained weighed about 10 grams. An extremely thin white film formed on the surface of the melts, sometimes covering only a part of the exposed surface. The ingots were filed clean, placed in small iror crucibles with close-fitting lids and indi. vidually sealed into Pyrex glass tubes Before sealing off, the tubes were alter

Jan 1, 1941

By H. L. Luo

SYSTEMATIC investigations of the Fe-Ga system have been reported only very recently."' The maximum solid solubility of gallium in a-Fe is nearly 50 at. pet at 900°C. However, from Ref. 1, it was not evident that the a-Fe solid solution could be retained successfully beyond 17.38 at. pet Ga by solid-state quenching. The present investigation reports the retention of a-Fe solid solution at 50 at. pet Ga by quenching from the liquid. An ordered phase of CsC1-type B2) structure was observed between 34 - 50 at. pet Ga. Since it was considered very probable that the CsCl structure would occur at high temperatures, alloy filings were also quenched by the conventional quenching technique. In addition to the CsCl phase, a second ordered phase of BiF3-type (DO3) structure was found in the range 25 - 30 at. pet Ga. Alloys were prepared from elements of 99.99 pet purity or better, induction-melted in alumina crucibles under hydrogen. After reweighing, the alloy ingots were cast into wires under argon. From the weight losses and the reproducibility of the lattice parameters, compositions were estimated to be within ± 0.3 at. pet. The techniques of quenching from the liquid state were reported before.3-5 Prior to quenching, a small section of cast alloy wire (30 - 50 mg) was melted in an alumina insert under an argon flow. The quenched specimens were in the form of flakes, typically 1 sq mm in area. For solid-state quenching, alloy filings passing 200 mesh were sealed under a reduced helium atmosphere in a thin-bottom silica tube. After heating for -30 min at the desired temperature in a vertical furnace, the sealed tube was rapidly dropped into ice water so that the thin bottom of the tube broke on impact. The quenched alloy filings were always ferromagnetic and could be collected by a magnet. X-ray diffraction patterns were taken with iron-filtered cobalt radiation in a 114.6-mm-diam Debye-Scherrer camera. High-angle lines were always resolved and spacings were computed relative to ? (CoKa1) = 1.78890Å. Lattice parameters were obtained from extrapolation against the Nelson-Riley function. The variation of lattice parameter with composition is shown in Fig. 1, together with the data of Dasarathy and Hume-Rothery.1 Uncertainties in the present measurements are within the dimensions of the symbols or indicated by error bars. X-ray diffraction lines indicative of CsC1-type ordering could be clearly identified for alloys of 34 - 50 at. pet Ga quenched from the liquid and alloys of 35 - 41 at. pet Ga quenched from -975°C. Within experimental error, no difference in

Jan 1, 1968