Search Documents

By lizabeth Morales

En el período del 2006-2007 un equipo multidisciplinario de especialistas nacionales e internacionales de Walsh realizó una evaluación de las condiciones ambientales de las operaciones de la Mina Tintaya, donde se verificó la información secundaria de la operación y los procesos participativos que lleva el yacimiento, generándose recomendaciones que ayuden a resolver conflictos entre la mina y la comunidad que sean aplicables a los asentamientos mineros en desarrollo en los diferentes países. En ese sentido, el presente trabajo describe el proceso de esta evaluación para así prevenir y minimizar conflictos sociales entre la empresa y la comunidad a través de un balance de las misma por intermedio de la mesa de diálogo.

Sep 14, 2009

By C. L. Magee, H. W. Paxton

The effects of testing temperature, frorn 77" to 420" K, and volume fraction of martensite on the micro-plastic response of unaged Fe-31Ni martensite-austenite aggregates have been determined. The kinetics of the aging phenomena which lead to a decrease in the microplastic response were also characterized. These determinations, supplemented by other experimental results, show that at least two mechanisms of plastic deformation give rise to the apparent softness of the quenched structures. Only one of these mechanisms is fully discussed in this paper The transformation of retained austenite to martensite during the application of stress leads, in specified conditions, to large microplastic strains. This deformation behavior cannot be described by normal transformation plasticity theory but is shown to result from the fact that stress-assisted formation of martensite is a possible deformation mode. The present results and further considerations of previous work lead to the conclusion that it is unnecessary to postulate a special work-hardening mechanism to explain the mechanical properties of unaged martensite. It is now generally accepted that dislocation motion can occur in many solids at stresses very much below the L'macroscpic" yield stress, e.g., 0.1 pct offset. This phenomenon has been investigated by a variety of techniques including measurements of elastic limit,' effective static elastic modulus,~ and irreversible deformation following stressing at low levels.3"5 Of particular interest to the work to be described are exper -iments conducted on the deformation of martensite in attempts to decide whether freshly quenched ferrous martensites are "hard" or "soft".6 Muir, Averbach, and cohenl and McEvily, Ku, and ~ohnston' have shown that as-quenched ferrous rnartensites can be plastically deformed at relatively low stresses. A difference between these two sets of experiments exists in that some diffusion of carbon would take place before testing in the experiments of Muir et a1. because the plain Fe-C alloys which they have tested transform to martensite well above room temperature. McEvily et a1. examined Fe-Ni-C alloys with Ms of about -30"~ and tested the alloys directly after quenching to — 195" ~ —a technique which obviates any appreciable carbon diffusion. Unfortunately, a characteristic of the alloys which transform below room temperature is that they do not transform entirely to martensite. The results discussed below will show that, because the transformation of this retained austenite under stress leads to plastic deformation, one cannot investigate the properties of martensite by such experiments. The existence of a second deformation phenomenon, which is not caused by retained austenite, is also established in the present work. In line with a previous suggestion,' it is believed that the second microdefor-mation mode is principally due to the internal stresses generated by the formation of martensite. To avoid confusion in the present report, the evidence we have found for this interpretation will be discussed separately in a brief note.7 EXPERIMENTAL Materials. The alloys were induction-melted and cast under vacuum; the resulting compositions are given in Table I. The ingots were hot-swaged to 2-in.-diam bar and further cold-swaged and/or cold-rolled prior to specimen preparation. The standard tensile specimens were machined from sheet. The gage section was 0.05 by 0.2 by 5 in.; 0.75-in.-wide ends had 0.2 5-in. centered holes for pinloading. The three-point bend samples were 0.075-in. thick and 0.6 in. bide. The distance between the outer loading points was 5.5 in. In order to establish a standard starting condition, all specimens were quenched to 77°K prior to annealing in vacuo for austenitizing. The temperature of the austenitizing anneal was controlled to + 5"~. The testing and aging temperatures were maintained by various liquid baths (nitrogen, 77"~; freon, 130° to 200°K; acetone, 200 to 300°K; silicone oil, 300' to 450°K) to better than il°K. Strain Measurement. The results herein were derived from both uniaxial tension and three-point bending experiments. For bending tests, the stresses and strains reported are those corresponding to the maximum fiber values. Normally, because of the small strains involved, very sensitive strain measurements are necessary to make microplastic measurements. However, because of the magnitude of the dilatation and shear involved in the martensitic transformation, the requirements in the present experiments proved to be less rigorous. In most experiments the plastic strain was evaluated by measuring stress relaxation and modulus defects. In this method, specimens are loaded rapidly to some predetermined load on an In-

Jan 1, 1969

By D. R. Irving

Prior to this time, ample supplies of high grade mineral fillers, such as clay, have been available close to consuming centers. Now depletion of these accessible deposits, coupled with other factors such as increasing demand due to population expansion and standard of living rise, has made development of upgrading techniques attractive to producers. Various investigations being carried out by the U.S. Bureau of Mines are described. Factors making the development of improved methods for upgrading clays attractive to producers include: depletion of accessible deposits of high-grade clays, rising transportation and labor costs, more exacting specifications, and increased demand resulting from an expanding population and a constantly rising standard of living. Industry recognizes the need for upgrading presently unusable materials and has cooperated with the U.S. Bureau of Mines by providing samples from submarginal deposits and by evaluating the products that USBM upgrades. Following are some examples of recent clay beneficiation work by the Bureau. FIRE CLAY BENEFICIATION At the Rolla Metallurgical Center, Rolla, Mo., the Bureau is conducting research to develop technically and economically feasible mineral-dressing methods to remove quartz, pyrite, and other impurities from submarginal fire clays. The research has been spurred by the growing shortage of high-grade bur-ley, flint, and plastic clays in the Missouri fire-clay district resulting from increased consumption and the low rate of discovery of new deposits of adequate quality. There apparently is ample tonnage of submarginal flint and plastic clays to maintain the industry for many years if such material can be upgraded to commercial quality. Samples have been submitted to USBM by several major producers of refractories, including A. P. Green Fire Brick Co.; Harbison-Walker Refractories Co.; Mexico Refractories Div., Kaiser Aluminum and Chemical Corp.; and Wellsville Fire Brick Co. Research on some samples has been completed and still is in progress on others. The Bureau has found that specimens containing quartz or pyrite in grains coarser than the accompanying clay generally can be upgraded either with a gravity table or hydraulic cyclone. The improvement in quality is notable not only in chemical analysis but in an increase in pyrometric cone equivalent (PCE) of one or more cones. As an example, consider the results attained on a sandy flint—a fine-grained mixture of kaolin and halloysite with quartz and minor quantities of iron and manganese oxides. Chemical analysis was: 35.4 pct alumina (A12O3) and 47.8 pct silica (SiO2). The sample contained 9.2 pct free silica as quartz. The PCE was 33. The sample was crushed to -10-mesh, blunged with water, and then stage-ground to -48-mesh. The ground sample was tabled to yield a clay fraction containing 37.6 pct A12O3, and 45.3 pct SiO2 of which 2.4 pct was free silica. The PCE was 34. Recovery of alumina by this process was 73.6 pct. Concentration of the same clay in the hydraulic cyclone was even more effective in respect to quartz removal. The clay fraction analyzed 38.6 pct A12O3, 45.0 pct SiO2 of which 0.5 pct was free silica as quartz, and had a PCE of 34. Recovery of alumina was 71.9 pct. The hydraulic cyclone was also effective in reducing the pyrite content of a plastic clay which likewise was a mixture of kaolin and halloysite, plus some pyrite, quartz, and carbonaceous material. It analyzed 30.6 pct Al2O3, 52.3 pct SiO2, 2.3 pct Fe2O3, and 0.76 pct S. The sample was blunged and screened through 10-mesh to remove some coarse pyrite, then ground to -65-mesh and cycloned to remove most of the remainder. The final product recovered 81.8 pct of the alumina at a grade of 32.3 pct A12O3, 50.9 pct SiO2, 1.4 pct Fe2O3, and 0.1 pct S. The PCE was 32-1/2, compared with a PCE of 31-1/2 for the crude clay. The fine beneficiated clays, of course, must be pelletized and dried or fired to meet commercial acceptance. This operation has already been solved by industry. Little progress has been made on two remaining problems. One is that of fine-grained impurities, not separable by table or cyclone. Flotation is being investigated to solve this. Although fine pyrite is readily rejected, a satisfactory quartz-clay separation has not been attained. The second problem, a stubborn one, is that of alkali. Samples containing as much as 5 pct potas-

Jan 1, 1961

By F. G. Jones, R. D. Pehlke, H. E. Gardner

The solubility of nitrogen in liquid Fe-18 pct Cr-8 pct Ni-0. 7 to 2.3 pct A1 alloys has been measured up to the solubility limit for the formation of aluminum nitride in the temperature range 1600° to 1700°C uszng the Sieverts' method. The solubility of nitrogen in 18-8 stainless steel increases with increasing aluminum content. Based on a nitride composition, AlN, the standard free energy of formation of aluminum nitride from the elements dissolved in liquid 18-8 stainless-steel alloys has been determined to be: ?G° = -42,500 + 20. IT in the range from 1600° to 1700° C. EVANS and pehlke1 have measured the equilibrium conditions for the formation of aluminum nitride, AlN, in liquid Fe-A1 alloys. The present study extends that work to the more complex solvent, liquid 18 pct Cr-8 pct Ni (18-8) stainless steel. Recent work by Small and pehlke2 has dealt with the effect of fourth-element additions on the solubility of nitrogen in 18-8 base alloys. They found the effect of aluminum additions, up to 0.74 pct, on the solubility of nitrogen to be small. The present study covered the range from 0.74 to 2.28 pct aluminum, and by extending the composition range may be used to better define the effect of aluminum on the nitrogen solubility in these alloys. EXPERIMENTAL PROCEDURE The Sieverts' method was used to measure the equilibrium solubility of nitrogen gas in liquid 18-8 stainless steel alloys containing 0.74, 1.49, 1.93, and 2.28 pct Al. The solubility was measured as a function of the nitrogen gas pressure at temperatures of 1600°, 1650°, and 1700°C. The apparatus used is the same as described by Small and Pehlke.2 The 100-g melts were made from Ferrovac-E high-purity iron, Crucible Steel Co.; 99.95 pct Cr, Union Carbide Corp.; 99.9 pct Ni, International Nickel Co.; and 99.99+ pct Al, Aluminum Co. of America. The aluminum was charged at the bottom of the crucible, surrounded by nickel and iron. The chromium was packed into the interstices to minimize vapor transport of the aluminum during initial melting. The hot volume of the system, measured for each melt with argon, ranged from 45 to 55 standard cu cm with a temperature coefficient of —8 x 10-3 cu cm per °C. The melt temperature was measured with a Leeds and Northrup disappearing-filament type optical pyrometer sighted vertically downward on the center of the melt surface. The temperature calibration of the system by Small and pehlke2 was assumed. Two problems are involved in determining the solubility product of a solid, metal nitride phase in liquid iron alloys. These are: 1) establishing the point of departure from Henrian behavior at the solubility limit of the metal nitride phase; and 2) determining the composition of the solid nitride which is precipitated. Determination of the solubility product of AlN was made by admitting small amounts of nitrogen into the reaction bulb until the deviation from Sieverts' law was clearly evident in the form of a pressure halt. To obtain the solubility product at several temperatures during one run the following procedure was used: 1) add increments of nitrogen to determine the Sieverts' law line at the lowest desired temperature; 2) continue to add nitrogen to precipitate a small amount of the nitride phase; 3) increase the melt temperature 50°C to dissolve the precipitated nitride; 4) repeat step 2 until either a nitride formed or the system reached ambient pressure; if a nitride formed at 1650°C, the sequence was repeated at 1700°C. The composition of the precipitated phase was checked by an X-ray diffraction pattern obtained from powder scraped from the surface of the solidified 1.93 pct A1 melt. RESULTS AND DISCUSSlON Solubility Measurements. Fig. 1 is a typical nitrogen-absorption curve obtained from measurements on a 1.93 pct A1 alloy. Since the initial absorption of nitrogen follows Sieverts' law the nitrogen solubility is plotted as a function of the square root of the pressure of nitrogen gas in the reaction bulb. The results of the solubility measurements for all alloys studied are summarized in Table I. The slope of the Sieverts' law line for each alloy was determined. Since this is also the solubility of nitrogen at 1 atm pressure of nitrogen gas, the latter designation is used for the data. It should be noted. however, that in most cases the value lies above the solubility limit for AlN. Fig. 2 shows the effect of aluminum on the solubility of nitrogen at this reference pressure and as a function of melt temperature. The solid portions of the lines represent attainable solutions; the dashed regions lie above the limit for precipitation of AlN.

Jan 1, 1969

Mark R. Lamb, Torres, Sonora, Mexico (communication to the Secretary*): I have read Mr. Merrill's paper with much interest, and cannot but accept his challenge as regards the cost of the clean-up at the Homestake mill. If I understand him correctly, the two men take the precipitates from the presses in about six hours, and do nothing towards refining them. If that is so, it would correspond to the work four men do here in about eight hours—that is, to clean the box and to place the precipitates in the driers. In order to make a fair comparison, the bullion in each case should be stated in ounces, since it is as diflicult to precipitate silver as gold, and our bullion is mostly silver. Bullion to the value of $50,000 is equivalent to a weight of about 2,500 oz. At our last clean-up eight standard bars, each 1,100 oz. in weight, were made, which equals a total weight of 8,800 oz'. Four men had the precipitates drying by 8 p.m. This plant, the Minas Prietas works of Charles Butters & Co., at Minas Prietas, has square-bottomed electrolytic vats, an arrangement which necessitates the handling of all the precipitates in buckets. The Butters plant at Virginia City, Nev., is equipped with conical vats, and probably could make a still better showing under similar conditions. Another point is that common labor only is required. (Ordinary laborer's wages at Minas Prietas are $0.70 gold.) I may say also that, except for the convenience of the refinery, the box could be cleaned monthly, instead of bi-monthly, at only a slight additional expense. The comparison, if made a few months ago, would have been much more in favor of the electrolytic process, as the tailings handled at that time contained a large quantity of copper, and the amount of zinc-dust required would have been enormous.

Jan 1, 1904

By Jay S. Gunasekera

Metal parts are traditionally processed by either filly-liquid (e.g., casting) or filly-solid (e.g., forging) state. Semi-solid metal forming incorporates elements of both casting and forging. In 1991, Gunasekera(5) developed a model illustrating the influence of flow stress by the liquid fraction. The result fits Kiuchi's (1979)(7) experimental data quite well. This model assumed the liquid part is surrounded by solid as small pockets inside the material, which is opposite to the real practical situation. Since the melting usually first happens at the grain boundary, it is better to treat the semi-solid material as small metal crystal surrounded by liquid.

Jan 1, 1997

By Hiroyuki Sano

A closed recycling process for the low-grade scrap of Al-based composite materials was developed. In this process flux treatment with water-soluble halide is a key technique. In the present work, flux treatment conditions were discussed from the viewpoint of the separation and the recovery of the base material, reinforcement and flux. Optimum separation condition was obtained for the NaCl-KCI-KF flux treatment. The recovered aluminum alloy can be recycled for various usages. The recovered SiC particles cannot be reused as reinforcement because of the coexistence of the contamination, therefore it is necessary to eliminate these contaminates or to find another use. The recovered flux is reusable with supplemental addition of fluoride.

Jan 1, 2003

THE progress in lead smelting practice in the United States during 1930 has been along previously defined lines. Since most of the material treated is high-grade concentrate relatively high in zinc, practically all the plants have been forced to adopt double sintering. This generally results in there being' no matte fall, and most of the copper in the charge is recovered in the furnace dross. The furnace dross is . smelted with. scrap iron and flux .in small reverberatories, giving a shipping matte or speiss high in copper and low in lead. Details of this reverberatory. furnace practice vary at the different plants. There is a decided tendency toward moreintensive filtration of blast- furnace and sinter fume. Bag capacity has been in- creased by using higher pressures and more frequent shaking.

Jan 1, 1931

By Wang Dawan

During the process of arsenic bearing gold concentration biooxidation, the content of chloride ion in water is a very important factor to the activity of bacteria and the oxidation of sulfide minerals. In this paper, the influence of underground mine water with different chloride ion content to the biooxidation of arsenic bearing gold concentration and the limit of chloride ion content to bacteria were summarized. These results indicated if the content of chloride ion was less than 1.2g/L, the bacteria?s ability to oxidize sulfide minerals was little affected, and if the content of chloride ion were increased to 2g/L or more, the activity of bacteria was seriously restrained, and if the content of chloride ion were increased to 4g/L, the activity of bacteria was absolutely restrained. So, as the content of chloride ion in water was cumulated to 2g/L or more in biooxidation plant, the water must be refreshed to maintain normal production.

Jan 1, 2008

By C. B. Espag de Klerk, J. de Goede, M. Le Roux, Q. P. Campbell

"Excessive amounts of moisture in product coal can influence the efficiency of downstream utilization processes due to a decreased calorific value and handling problems. Stockpiles can be used to decrease the moisture content of coal by means of gravity drainage and evaporation. This paper is focused on the evaporation of moisture from a coal stockpile surface with the aim of investigating the effect of particle size on the rate of evaporation as well as the depth to which evaporation extends.It was observed that moisture initially evaporates at a higher rate from a stockpile consisting of fine particles (-6.7 mm) than from coarser particles (-13.2 mm +6.7 mm). This high rate of evaporation is restricted to the outer shell of the fine coal stockpile. However, for coarse coal, the porous nature increases the depth at which evaporation occurs. Evaporation of moisture was observed up to the fourth day of each experimental run, after which steady state was obtained. It was shown the water can evaporate from the surface into the body of the stockpile, depending on the coal particle size and void spacing. An experimental reclaim depth of 0.4 m was achieved after 4 days. IntroductionCoal stockpiles serve as surge capacity for downstream utilization processes and can also be used for moisture reduction by means of gravity drainage and evaporation. Excessive amounts of moisture in coal can cause handling problems and, most importantly, will decrease the calorific value, leading to inefficient combustion.Research has shown that evaporation by means of wind and solar action is considerably more effective than gravity drainage(Williams, D.J. 2006), but the effect is limited to a restricted depth from the exterior of the stockpile (Boyapati, E. and Oates, A. 1994; CSEM-UAE, 2010). The effectiveness of wind and solar action can be improved by orienting the stockpile perpendicular to the predominant wind direction, maximizing the surface area of the pile, and reclaiming the coal from the pile gradually in shallow cuts over a large area (Williams, D.J. 2006)."

Jan 1, 2016

By Taiping Lou

The coarsening process of precipitates in non-equilibrium systems was studied, and then a physical model of coarsening was proposed. The coarsening process of CaO'TiO2 in MgO-TiO2-Al2O3-SiO2-CaO-CaF system was investigated. It is shown that the coarsening process by the model predicting is agreed with the experimental results.

Jan 1, 2000

By S. Kemball-Cook, D. Heinze, A. Kornberg, M. Harmon

Climate change presents risks to mine infrastructure, operations and long-term obligations to protect environmental conditions. Management strategies and design of infrastructure and containment systems based on past or current climate conditions may be inadequate in the future if changes in climate are not taken into account in planning for mine operations, decommissioning, closure and post-closure. Data-driven assessments using climate model projections of the future can be used to quantify: • Changes in site-specific risks to mine structures, access, containment facilities, operations and staff safety. • Changes in vegetation and water balance/chemistry, and potential for acid mine drainage, erosion and design failure. Climate- and weather-related risks are a serious threat to the mining industry, but risk transfer solutions can alleviate these vulnerabilities. Mining companies can protect themselves through bespoke solutions which provide operators, investors and buyers with protection against weather-related disruptions to operations by hedging to smooth revenues. Using risk transfer structures to mitigate climate risks is a mechanism that is available to all types of mining operations world-wide. In this paper, we describe methods for evaluating site-specific climate change impacts and developing risk transfer solutions to mitigate their effects. EVALUATING MINE RISKS FROM CLIMATE CHANGE The best available tool for understanding potential future changes to the earth’s climate system are global climate models (GCMs) (IPCC, 2014). GCMs are computer simulations of the climate system which include the atmosphere, ocean, land surface, cryosphere and biosphere. Because of the computational demands of running a global model for many decades, the spatial resolutions of the GCM grids are necessarily coarse, typically on the order of 100-300 km. GCM data are therefore suitable for evaluating future physical risks on global or continental scales, but may not be appropriate for evaluating location-specific risks (e.g. Kotamarthi et al., 2016). For site-specific, quantitative physical risk assessment, GCM projection data are “downscaled” or adapted for use at the local level using statistical techniques together with observed data (statistical downscaling) or using high-resolution regional climate models (RCMs) that focus on a single geographic region and have spatial resolutions of 10-50 km (dynamical downscaling). Downscaling bridges the gap between the GCM scale and regional/local scale. Through the downscaling process, new information is added to the GCM output from observations and/or RCMs, resulting in patterns for weather variables that are more consistent with local terrain and weather influences. Downscaled climate change projections for the mine site are selected considering mine location and geography, the availability of local observations, and the performance of the downscaling method and global/regional models used to develop the projection in simulating the variable under study. Where possible, we use projections from an ensemble of global and regional model runs spanning a range of future greenhouse gas (GHG) scenarios.

Jan 1, 2019

By A. Dadgar

Extraction of gold and silver from two refractory concentrates using cyanide and bromine reagents was reported at the 12th International Precious Metal Conference (1). The objective of this paper is to present the gold extraction, recovery, and economics for two refractory concentrates using cyanide and bromine reagents. Gold extractions for cyanide leaching (24- 48 hours) and bromine leaching (6 hours) were the same and ranged from 94% to 96%. Gold recoveries from bromine pregnant solutions using carbon adsorption, ion exchange, solvent extraction, and zinc and aluminum precipitation methods, were better than 99.9%. A preliminary economic analysis indicates that chemical costs? for cyanidation and bromine process are $9.50 and $10.50, respectively per ton of calcine processed.

Jan 1, 1989

By R. Eggert

Since the discovery of high temperature superconductors has led to extensive interest and conjecture regarding their potential to change contemporary technology, discussions of the impact on the metallurgical and other industries have naturally arisen. In this paper we present data showing the possible impact of these developments on the materials related to the fabrication and proliferation of devices based on superconductor materials. We observe that the largest volume of effort with LTSC will be for the demonstration of high power devices while applied research relating to processing will remain the principal HTSC activity. We also note that in the next decade copper consumption in the US is expected to remain essentially at the current level while the need for Nb and Sn,; two major components of LTSC, will grow at a faster rate both in the US and the world. Although the use of superconductor-based magnetic separation is anticipated to increase, no major impact of these components on the metallurgical industries is expected.

Jan 1, 1990

By A. C. Veatch

Jan 1, 1921

By James R. Cudworth

OUR colleges and universities have met many difficulties during the past year. From a period of small enrollments and depleted faculties, the educational institutions have passed quickly to a period of the largest enrollments in their history with inadequate facilities and staffs. The results of the shortsighted policy of the Selective Service system which drained the technical schools and universities of many of the students who were potential teachers are now being felt. The movement of faculty members into positions in industry during the war years has resulted in many of them forsaking permanently the educational field for the higher salaried positions they now occupy. Competition is keen between the educational institutions, and between the institutions and industry, for technically trained men. Dean Holbrook's statement in last year's annual review that he thought it would take three or four years to restore our engineering departments to their former level in quality of instructors is even more convincing today. Somehow, the institutions must not only reach their former level in quality of instruction but they must also increase the quantity of their staffs to meet the demands of the ex-service men and the high school graduates for engineering education. The enrollments in the mineral industry fields of mining, metallurgical, geological, petroleum, and ceramic engineering, although greatly increased, are not expanding as much as in the more widely known fields of electrical, mechanical, aeronautical, and civil engineering. In fact, many educators are tremendously worried about the segregation of so many young men in a relatively few fields while the needs of others will remain unanswered.

Jan 1, 1947

By Sidmar Aparecido Ceresani

O presente estudo tem como objetivo demonstrar a cinética de recristalização e o amolecimento da liga C272000 processada na laminação a frio com uma deformação de 75%. Para determinar o modelo cinético Johnson, Mehl e Kolmogorov (JMAK) foi adotado a temperatura de 450° entre 5min. a 50min. Restaurando totalmente a microestrutura deformada plasticamente sendo progressiva a elevação do tempo e da temperatura. A caracterização microestrutural das amostras foi utilizado microscopia óptica e metalografia. Conclui-se que o modelo JMAK satisfaz a forma de nucleação da recristalização da liga C272000.

Oct 30, 2017

By Mario Luiz Cruz Nascimento

Devido a seu preço competitivo e alta resistência à fluência e à corrosão, atualmente as colunas dos fornos de reforma são confeccionadas com tubos fundidos por centrifugação de aços inoxidáveis austeníticos da classe HP modificados ao nióbio. Apesar de projetadas para uma vida mínima de 100.000 horas em serviço, falham frequentemente devido a intercorrências operacionais que levam ao superaquecimento localizado, designados surtos de temperatura. No presente trabalho, microscopia eletrônica de varredura (MEV) e microanálise por energia dispersiva de raios-X (EDS) foram utilizadas para estudar duas colunas trincadas após um surto de temperatura. Descobriu-se que o NbC reprecipita na morfologia de pequenas partículas nos sítios onde a fase G foi dissolvida durante o surto de temperatura. Desta forma estas partículas servem como marcadores microestruturais da ocorrência do surto.

Aug 17, 2017

By Dongping Duan, Hongliang Han, Li Zhong, Siming Chen, E Zhou

In this study, physical, chemical and microscopic characteristics of Celestine were investigated firstly. Based on which, the thermodynamic analysis of Celestine reduction was discussed. And the experiments of Celestine carbon-containing pellets used in rotary hearth furnace process were studied. The results showed that it is feasible to deal with Celestine by rotary hearth furnace direct reduction process. When the temperature is 1200°C, C/O ratio is 0.8 and holding times is 20min, the conversion rate of SrSO4 in Celestine is above 95%, the utilization rate of Celestine is nearly 100%. This study can provide theoretical and technical basis on economical and rational use of Celestine.

Jan 1, 2016

By Andrea Brickey, RICHARD AMOAKO, Akshay Chowdu

Production forecasts derived from the medium-term schedule represent the best path forward for underground mining operations to achieve corporate and operational goals. Unforeseen circumstances, such as equipment breakdown, can cause significant deviations from established production forecasts in the short term. Such situations require timely mitigation of the effects of the deviations in order to stay as close as possible to the medium-term plan. This paper presents a deterministic mathematical formulation for short-term scheduling that addresses this challenge. The formulation is able to make up for deficits resulting from operational disruptions by minimizing deviations from medium-term production goals and medium-term activity start dates. We demonstrate this in a case study by simulating disruptions involving reduction in ore extraction capacity and development advance rate. Aside from the rescheduling capability, this formulation can help mine planners conduct analysis on the impact of various disruptions on the schedule. The formulation can help identify those conditions or disruptions that are more detrimental to the achievement of forecast targets, or otherwise. The formulation also affords mine planners the flexibility to prioritize one production goal over the other, depending on operational conditions at the mine. In the future, we seek to incorporate in the formulation respirable dust, diesel particulate matter and ventilation constraints in order to create more realistic schedules, and enhance miners’ health and safety.

Jan 1, 2024