Search Documents

By Alain Denis, Marcelo Curtes Martins, Jeferson Rocio de Oliveira

In this work we present a study of optimization of a new inhibitor for turbulence pickling line. The efficiency of inhibition was measured and the weight of loss was evaluated in four different materials to optimize the dosage of the inhibitor. In seven months we had 8.7% of reduction in pickling losses.

Oct 1, 2019

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By Cyro Takano

A tecnologia de autorredução apresenta um grande potencial por apresentar características de alta velocidade de redução e de eficiência energética, resultando em economia de energia e em alta produtividade na produção de metal primário. Têmse dois processos consolidados de aglomeração. A utilização de cimento como aglomerante, com cura a frio que formam hidratos que conferem resistência, apresenta problema principal de sofrer degradação às temperaturas na faixa de 800 a 1000 °C, devido à decomposição dos hidratos. O outro processo é o de utilização das propriedades do carvão de alta fluidez e tratá-lo termicamente para que sirva de redutor e aglomerante. Este processo não é o de cura a frio, porém diminui consideravelmente a quantidade de escória em comparação com a utilização de cimento. O objetivo deste trabalho é o de analisar, na literatura técnica, os aglomerantes alternativos e iniciar os ensaios para verificar os comportamentos de resistência mecânica, principalmente a quente. Em função dos resultados a etapa seguinte será a de projetar um processo que seja compatível com resistência mecânica a quente. A análise resultou em sugestões para os ensaios. Os resultados preliminares, com utilização de bentonita e ácido bórico estão indicando resistência a quente das pelotas melhores que as obtidas com a utilização de cimento.

Aug 17, 2017

By Dyego Irineu Silva de Almeida

O presente trabalho teve como objetivo analisar os efeitos dos ciclos de tratamento térmico de recozimento, normalização e esferoidização nas características microestruturais do aço SAE 8620. O aço SAE 8620 é amplamente utilizado na fabricação de engrenagens, pinos e peças onde há exigência de dureza superficial, obtida pelo processo de cementação ou carbonitretação. O aço SAE 8620 é empregado na construção de mecanismos onde a resistência ao desgaste é propriedade mais importante. Para essa aplicação, aços com baixo teor de carbono produzem um núcleo tenaz e os tratamentos termoquímicos conferem as características superficiais necessárias. O espécime original foi caracterizado através dos procedimentos necessários para visualização da microestrutura, bem como as amostras provenientes dos tratamentos térmicos. Sabe-se que o estudo metalográfico de um material é de grande importância para a identificação de suas propriedades, haja vista que essas propriedades estão diretamente relacionadas com a microestrutura que o material possui. Concluiremos que os diferentes ciclos de tratamento térmico, influenciam diretamente nas microestruturas das peças tratadas termicamente, como também na propriedades mecânicas.

Oct 30, 2017

By Yuechang Wang

A new method of manufacturing the wavy-tilt-dam(WTD) mechanical seal has been mentioned. In this method, the special equipment is designed to provide a predetermined force to external and inner circular surface of the ring. After milling the end face of the seal by grinding miller and releasing the preload, the wavy-tilt-dam can be done on the seal surface. In this paper, a prediction model is built up to investigate the relationship between the predetermined force and the deformation on the surface of the ring by using ANSYS software. A WTD ring is manufactured by this method which approves that the prediction model is in accord with the real process and this manufacturing method of the WTD mechanical seal is a proper choice.

Jul 31, 2018

By Romeu Thomaz Viana Júnior

Este trabalho tem como objetivo apresentar a implantação de tratamentos termomecânicos no novo laminador de chapas grossas da Gerdau Ouro Branco, descrevendo seus mecanismos metalúrgicos e o correspondente efeito nos produtos. Para melhor ilustrar essa atividade, tomou-se como exemplo os resultados de testes bem sucedidos de aços estruturais de alta resistência e baixa liga, graus 80 e 90 ksi (550 e 620 MPa, respectivamente), com microestrutura predominantemente bainítica.

Oct 30, 2017

By BTrubT M

In the roast-leach-electrolysis process for the production of zinc, iron contained in zinc concentrates is converted to zinc ferrite during roasting. At Canadian Electrolytic Zinc (CEZinc), the Outokumpu Conversion process is used to simultaneously leach zinc ferrite and precipitate the iron as jarosite. These simultaneous reactions, while providing good process stability, require a compromise between optimum conditions for maximum zinc extraction and efficient iron precipitation. An improved conversion process has been identified which can achieve >99 per cent zinc extraction and more efficient jarosite precipitation to residual iron concentrations of

Jan 1, 1993

By Raissa Santos Salgado

Atualmente, a exigência do mercado pela produção de aços de alta qualidade aliada a redução de custos, impulsiona maiores investimentos em novas tecnologias e a busca pelo melhor conhecimento dos processos que ocorrem na usina siderúrgica. O desgaseificador RH tem-se revelado um equipamento fundamental para produção de aços ultra low carbon, tipo cada vez mais solicitado pelos maiores consumidores de aço. Diante disso, este trabalho visa a elaboração de um modelamento matemático das curvas de descarburação e desidrogenação no RH thyssenkruppCSA. A geração dessas curvas possibilitou o estudo do comportamento do teor de carbono e hidrogênio durante o tratamento das corridas no reator. Os resultados demonstram que o teor de carbono médio obtido não está dentro do esperado, conforme previsto pelo comissionamento. No entanto, a desidrogenação pode ser considerada como satisfatória.

Oct 30, 2017

By Thiago Cesar de Souza Pinto

Os teores de umidade (U) presente no minério de ferro, após o processamento mineral, se torna uma dificuldade para seu transporte marítimo à medida que este teor ultrapassar os limites de TML (Transportable Limit Moisture). O presente trabalho teve por objetivo a identificação dos mecanismos de secagem em concentrados de minério de ferro tipo sínter feed em unidade experimental de secador de bandejas em escala de laboratório. São apresentados e discutidos resultados em que os mecanismos identificados se revelam como água livre superficial e capilaridade, para a faixa de umidade de interesse (13<U<6%). Uma regressão não linear foi realizada identificando o peso das variáveis em estudo, permitindo assim um modelamento dos resultados de redução de umidade. O modelo apresentou boa aderência aos resultados experimentais com desvios menores que 10% entre os dados previstos e observados.

Aug 16, 2017

By D. Tait, M. A. Halim, V. I. Lakshmanan, R. Sridhar

Rare earth elements (REEs), nickel and cobalt find their use in developing strategic materials and their demand is consistently increasing in the world while the extractable ores of these metals are gradually depleting. Process Research ORTECH Inc. (PRO) has developed innovative mixed chloride leaching processes for the recovery of REEs from alumino-silicate ores, and nickel and cobalt from laterite ores. The addition of magnesium chloride in hydrochloric acid enhances the activity of the hydrogen ion by orders of magnitude, which permit rapid leaching rates at moderate temperature and atmospheric pressure, along with high metal recovery. Innovative solvent extraction process steps are used for the separation of these metals from pregnant leach solutions. PRO’s processes also produce value added by-product of high purity iron oxide and recycle chloride lixiviant to the leaching stage. This paper describes the leaching and separation reaction mechanisms and potential process flowsheets.

Mar 1, 2017

By William E. Souder

The behavioral accident simulator (BAS) is a computer program that can be used to simulate accident situations. It demonstrates how the potential to have an accident grows or diminishes as a result of changes in various environmental, organizational, and behavioral factors. It calculates the number of fatalities that may result from various conditions and graphically displays these data. The BAS is useful for studying systems of accident causes, for demonstrating the various ways to diminish fatalities, and for training employees. This Bureau of Mines report provides the detailed instructions needed to use the BAS.

Jan 1, 1988

By Michael G. Zabetakis

Investigation of gas explosions usually reveals that the combustible gases have come from transmission and storage facilities or from natural gas or oil wells. However, combustible gases such as methane and hydrogen can derive from biological processes. Hazardous situations have been created in the past by the use of abandoned mines for the disposal of sewage and rainwater, by the interconnection of storm and sanitary sewers, by sealing the openings in manhole covers when repaving the roadway over a sanitary sewer, and by the construction of buildings over or near garbage fill areas without adequately providing for the release of combustible gases.

Jan 1, 1962

By J. M. Mutmansky

This paper outlines patterns of methane emission in both longwall and room-and-pillar operations and the effects that these patterns have on the decision as to whether the methane is most economically handled by ventilation alone or by means of a methane drainage system in addition to ventilation. The costs of handling the methane in the ventilation system and the costs of implementing the methane drainage system will be discussed as well as the costs related to the production of coal. The important issue of production slowdowns and gas outs will also be discussed as well as the proper response of mine management to such a situation. Suggestions concerning the keeping of production records related to methane problems will be made as well as justification for more intensive economic analysis of coalbed methane extraction and utilization.

Jan 1, 1998

By G J. Jameson, A Agarwal

This paper is concerned with the observation and analysis of bubble clusters in a laboratory flotation cell. A device was used in which bubbles were allowed to rise in clean water containing the same frother and collector concentration as in the cell. Bubble clusters were recorded using a high speed camera and analysed using an image analyser. Dodecyl amine was employed as a collector to float silica. The effect of impeller speed on the cluster behaviour was investigated. The results were interpreted in terms of cluster diameter and shape factor. The sizes of the bubbles forming the clusters were also measured and compared to the sizes of the independent bubbles in the cell. It was found that there was an optimum impeller speed in which the cluster diameter was a maximum. Higher agitation and the consequent higher power inputs resulted in cluster break-up while lower shear rates promoted cluster formation.

Jan 1, 2005

By Kenneth A. Brunk

"This address discusses how ""Mineral Processing Technology"" can play a major role in the life and profitability of a mining company. Examples of past and present technological breakthroughs and their impacts will be examined. Also, the future of processing technology will be emphasized.IntroductionThis talk will center on the role of technology as an important component of a business plan for mining companies. I'll attempt to explain how I see technology development as an underpinning of a successful mining company. We will examine an example of a technology that has resulted in a re-birth of segments of the industry, examine a technology life cycle and discuss technology as it relates to ore reserve replacement. Also, we will touch on technology in today's mining company and propose some food for thought for those designers of corporate organizations."

Jan 1, 1997

By Z. Y. Xie

The visualization techniques were employed for the analysis of computer simulation studies of dislocation core structure in ordered alloys. Atomistic computer simulation was used for the study of the local configuration of the material in the vicinity of the dislocation. Stresses were applied in the simulation in order to study the necessary stress level for the dislocation to move and onset plastic deformation of the material. The results were analyzed in terms of the strain tensor as a function of the position (x, y) in the material with the dislocation located at (0, 0). Various visualization packages are used to plot the invariants of this strain tensor and to visualize the changes that the dislocation core undergoes under stresses until it finally moves.

Jan 1, 1993

By Joel Ochoa, Miguel A. Montiel

El análisis metalográfico se usa en las industrias como herramienta para ayudar a identificar un metal o aleación, para determinar si una aleación se procesó correctamente, para examinar múltiples fases dentro de un material, para caracterizar imperfecciones tales como poros o impurezas, para observar daños o degradaciones y para hacer análisis de fallas. El método para hacer evaluaciones utilizado en el presente estudio es la microscopía óptica, que al igual que la de barrido electrónico con análisis de rayos X de dispersión de energía (SEM / EDX), logra buenos resultados al efectuar un análisis metalográfico.

Dec 31, 2018

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

By V. B. Telles, D. C. R. Espinosa, J. A. S. Tenório

"The purpose of this work was to study the reutilization of the steelmaking dust, derived from steel production in the electric arc furnace (EAF), in iron ore sintering process aiming zinc elimination. In each sintering process were collected sintered samples, these materials were analyzed by chemical analysis using atomic absorption spectrophotometry in order to determine the zinc content. Samples of not sintered mixtures were also characterized by chemical analysis aiming to determine the initial amounts of zinc, i.e. in order to check the zinc amounts present in the mixture before the sintering process. The comparation among the zinc contents of samples sintered and not sintered allowed to determine the elimination of zinc during the experiments. Results showed that the zinc elimination in the process is proportional to the ratio reducer/waste. The zinc removal was lower when the reducer/waste ratio was decreased.IntroductionThe electric arc furnace dust (EAFD) is a residue generated in the steelmaking process using electric arc furnace. Aproximately 30% of all steel produced (in the year 2009) was obtained through electric arc furance (EAF). In the United States of America the percentage of this process in the total crude steel production was about 62% in 2009, while in 2000 this percentage was only 47% [1].The iron ore sintering is a process that reuses wastes generated in metallurgical industries. However, the materials used must be physical and chemical characteristics compatible with the blast furnaces.The quantity of zinc, cadmium, chrome and other metals present in the EAFD depends on the quality of the scrap used to feed the EAF and the type of steel that it is been made [2,3]. The reuse of EAFD waste is interesting to steelmaking processes because of its iron content. However the presence of zinc inside a blast furnace is undesirable since the zinc oxide can be deposited on the blast furnace walls and in the drivers of gas output, interrupting the flow. Another part of the zinc oxide can form deposits on the refractory lining of the blast furnace [4,5]."

Jan 1, 2012

By Chee Theng

"So many talks, so little time.One of the toughest challenges associated with attending the SME Annual Conference and Expo is deciding how to allocate one’s resources. After accounting for keynote and plenary sessions, committee meetings, networking events, luncheons and exhibits, attending even one of the 109 technical sessions and more than 600 technical paper presentations can be a labor of love. Many, however, managed to make it to many of the sessions, including the mineral and metallurgical processing technical session on solvent extraction, ion exchange and electrowinning.At one point, that room was seated to near capacity, with a considerable number of the audience members standing by the walls at the back. Brittany Valera of Freeport-McMoRan Inc. was one who came early and enjoyed the session in its entirety. "Everything was pretty exciting," she said. "I really liked the modular plants. I think the future of mining, just like what we talked about in there, lies in thinking about things like remote locations, lifetimes of plants, anything that would be reusable and sustainable; and lower-cost and user-friendly would be really beneficial."Michael Moats, associate professor of metallurgical engineering at Missouri University of Science and Technology, started off the session by presenting on behalf of post-doctoral student Alex Luyima, who, like many before him, had been snapped up by industry and is now working for a secondary-metals refining company in Texas. Their team studied the nucleation and growth mechanism of copper on stainless steel from synthetic acidified copper sulfate in the absence and presence of chloride ions and three commercial organic additives: Hydrostar 4208, DXG-F7 and Cyquest N-900. Currenttime data were analyzed using known models, with reference to scanning electron microscope images. Good agreement was achieved between the models and SEM micrographs of deposits at a commercially relevant current density of 30 mA/ cm2. The addition of 20 mg/L chloride was found to increase the size and reduce the number of nuclei. The addition of 2.5 mg/L of each additive did not change the mechanism, but all three reduced the size and increased the number of nuclei, leading to more uniform coverage of the substrate with smoother deposits produced in twohour electrowinning experiments. N-900 had the best deposition coverage while DXG-7 was the easiest to dissolve."

Jan 1, 2014