Search Documents

By Rixon K. L

Hargraves (1983) has reviewed the phenomenon of instantaneous outbursts of coal and gas with special attention to Australian occurrences. The purpose of this discussion is to highlight some problems and omissions in his review that reflect particularly on the authors' structural geological investigations of outburst-prone coal seams.It is surprising to find that much of the authors' reported work has either been glossed over or the results distorted by Hargraves (1983) and it is, therefore, important to clarify the contribution that structural analysis of coal seams can make.For many years it has been known that faults provided preferred loci for gas outbursts (for example, Briggs 1920-21) but the roie that faults played in outburstprone seams was unclear. The present authors reviewed the association of faults and outbursts drawing upon local investigations and the world-wide literature (Shepherd et aI., 1981), and discussed some wideranging aspects that result from the high coincidence of faults and outburst sites. Without repeating large segments of this article the authors will discuss four aspects of coal seam faulting and fracturing.

Jan 1, 1983

By J. C. Schneider, G. Van Weert

Hydrochem Developments Ltd. has developed and put into full scale operation a novel type of vertical flotation column incorporating a multiplicity of mechanically agitated stages. Characteristics of this flotation column include a low height to diameter ratio, high upgrading factors and the possibility of modifying geometry and operation to specific flotation requirements. A commercial unit is currently handling up to 100 tpd rougher concentrate at Dickenson Mines Limited, Balmertown, Ontario. Design parameters and plant performance will be discussed.

Jan 1, 1988

By S Chew, A Bennett, N Di Giorgio, B Osborne

After relining one of two blast furnaces and enlarging its sinter plant in 2009, BlueScope radically restructured its Port Kembla steelworks operation in 2011, shutting a blast furnace and halving its total production. This drastic move in response to unprecedented raw material prices relative to achievable steel prices was like that of many integrated steelmakers worldwide facing similar challenges. The 2011 restructure also saw major changes in the amount and type of iron ores and ferrous burdens purchased, and a fundamental reappraising of ‘value’ in iron ores. This paper outlines the changes to raw materials purchases from 2011 to 2017, how BlueScope has responded to the changes in pricing and raw materials quality, the effect on the sintering and blast furnace processes at Port Kembla resulting from higher gangue content, some of the broad technical and economic challenges faced by steelmakers confronted with lower quality iron ores and how BlueScope is meeting those challenges.CITATION:Di Giorgio, N, Bennett, A, Osborne, B and Chew, S, 2017. Recent Port Kembla experience with iron ore use – sintering and blast furnace, in Proceedings Iron Ore 2017, pp 25–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Frank E. Chase, John L. Ellenberger, Christopher Mark

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

By Victor C. Bryan

One of the most sought after answers in any consideration of blasting activities relative to mines and quarries is how to safely and efficiently use explosives. While that discussion might be relatively straightfonvard in a “site specific” situation. it becomes more complex when viewed from a broad geographic perspective. Such is the case in considering the operations of one United States producer of crushed stone with surface and underground mines spread over a thirteen state area. Differing geologic environments set conditions that dictate to the blaster as now specifically to get optimum results from the blast hole. This treatise is a discussion of the various methods, materials, and principles used in conducting such blasting operations.

Jan 1, 1991

By Gregory Yates

INTRODUCTION Project Description The Silver Line is a Bus Rapid Transit (BRT) Line and is Boston?s newest transit service. Silver Line Phase I extends along Washington Street entirely on the surface in priority bus lanes from Dudley Station in Roxbury through the South End and Chinatown neighborhoods to downtown Boston. The Phase I opened in July 2002. Silver Line Phase II consists of an underground transit tunnel from South Station to the South Boston Waterfront with underground stations at Courthouse and World Trade Center to Silver Line Way east of D Street. Phase II continues through the Ted Williams Tunnel to all the terminals at Logan Airport, and on the surface to the Boston Marine Industrial Park and City Point. Phase II opened in December 2004. Silver Line Phase III is a one mile tunnel connection to the existing Phase II tunnel in the vicinity of South Station and will eventually portal on Tremont Street just north of Marginal Road. After leaving the portal, the buses will use dedicated bus only lanes on the surface roadway network to connect to the Phase I service. Figure 1 shows the alignment of the Silver Line upon completion of the Phase III project.

By R. J. Hickson

From 1993 through 1999 Cyprus Amax Minerals Company successfully completed eight major construction projects around the world. Six greenfield mines were brought into production, an ongoing operation was completely modernized, and an environmental issue was appropriately remediated. The projects stretched over three continents, from arctic Russia to the Atacama Desert, from 16,000feet to sea level, from city suburbs to remote wilderness, from a low of $130 million to over $1 billion. Open pit and underground; mill and leach; gold, copper, molybdenum, and coal were all encompassed. The breadth of diversity experience from these projects inspired Cyprus Amax to create a “best practices” project management protocol, to steer corporate expansion into the next millenium. This paper summarizes those best practices, while high-lighting project management pitfalls to avoid.

Jan 1, 2000

By J. C. Willett, J. R. Sanfilipo, P. D. Warwick

The U.S. Geological Survey has conducted an assessment of the Nation’s coal deposits that potentially could be mined during the next 30 or more years. For the Gulf Coastal Plain region, the assessment includes reviews of the stratigraphy, coal quality and resources, and coalbed methane potential of the Cretaceous, Paleocene, and Eocene coal deposits in the region. The results of these efforts are a series of digital maps, text, and tables published in CD-ROM format. Although abundant coal resources are available in the Gulf Coast region, coal quality issues may limit large-scale development in the future. Additional data are required to better evaluate the coalbed methane resource potential for the Gulf Coast region.

Jan 1, 2001

By B. M. Coombes

The McCracken and Stacey (1989) method of assessing geotechnical risk for largediameter raisebored shafts has been the basis for most Australian pre-construction raisebore investigations for the past 20 years. At the time of its publication, the McCracken and Stacey (M&S) Method did not include a database of raisebore diameter and rock mass conditions versus actual performance. It did, however, provide a chart that quantified geotechnical risk in terms of proposed shaft diameter and the raisebore rock quality index, QR. Two parameters, RQD/Jn and Jr/Ja were identified as being critical to raisebore stability, but the contribution of these to overall raisebore stability was not quantified. Peck and Lee (2008) published a database of raisebore performance from Australian case histories. Raisebore diameter and ground conditions, in terms of a Lower Bound QR value, were presented for 50 cases versus raisebore performance. This paper updates the database with further case histories and corrected SRF values. This paper further evaluates the reasons for the variable raisebore performance for similar RSR values. For all case histories, three parameters, RQD/Jn, Jr/Ja and Jw/SRF are investigated to assess their influence on raisebore performance.

May 1, 2011

By Lorenzo Pellegrini

The respect of EPB reference pressure during TBM advance and hyperbaric activities, the complete and effective filling of the annular gap between tunnel lining extrados and the excavation section and a well organized monitoring system, to control surface settlements and ground distortion, are items of utmost importance in EPB tunnelling process. The paper describes how these concepts have been applied while excavating in the difficult underground conditions found at Sao Paulo (Brazil) during the execution of the Sao Paulo Metro Line 4-Lot 1. In this project, the annular gap has been filled by two components type, cement grouting. The back feed of the extensive monitoring campaign carried out to check the surface settlements during the excavation and hyperbaric maintenance operations will also be described in the paper.

By Des Bolton

With the introduction of Cast Blasting techniques, field controls of Drilling & Blasting operations became more important. New drills were purchased which were equipped with sophisticated instrumentation and more accurate drilling plans were required. Concurrently a decision had to be made on the replacement of borehole logging equipment owned by the mine. The use of a contractor to log blast boreholes was eventually decided upon, the information gained from this operation is used in the short-term drill and blast planning and may also be used to assist in the coaling operation if density I quality correlations prove acceptable.

Jan 1, 1994

By Robert Schnab

ASFINAG is responsible for the construction and operation of the Austrian highway system. It is approx. 2,400 km of highways and 65 tunnels with a total length of 200 km including the Tauern Tunnel. In order to improve the documentation of the tunnel construction, ASFINAG chose to use a state of the art tunnel scanning system to record the various stages of construction: excavation, initial shotcrete lining, smoothing layer and final cast in place concrete lining. The geometric and photogrammetric documentation is provided on a daily basis to all par-ties involved. This innovative concept provides accurate & complete information in real time. The tunnel scanner documentation of the 2nd tube at the 6.4 km long Tauern Tunnel will be presented in this paper as a part of the survey contract.

By Vojtech Gall

Pre-support measures for urban tunneling have seen a substantial development in the recent past. Ground improvement techniques, pipe-arch and spiling methods now allow for non-disruptive tunneling at very shallow depths under sensitive structures, rail tracks and roadways. The paper presents experience gained on national and international projects built over the past decade that represent case histories and therefore may be used as guidance for the development of similar solutions for future tunneling projects at shallow depths. Reference projects include tunnels for the Washington, DC Metro, London Underground, Dulles Inter-national Airport, Busway tunnels in Boston and the Ft. Canning Tunnel in Singapore.

Jan 1, 2008

By Maurizio Siepi

The realisation of most of the civil engineering works is subordinate to the execution of consolidation works, in order to improve the soil physical-mechanics characteristics. The works classifiable with the term "Soil Improvement" can be realised using several technologies, among which the Deep Mixing Method is distinguished for his remarkable flexibility and productivity characteristics. The Deep Mixing Method is a process whereby a rotary drilling machine mechanically drills a constant diameter hole while cement slurry is injected into the soil at high pressure. The process combines state of the art construction techniques merging mechanical and hydraulic mixing energies at the tool bit. The result is a soil-cement column of engineered strength, consistency and dimension. Whereby the soil cement column formation process is controlled by a computerised device, the result is a speedy installation, thorough mixing, and a high degree of control, repeatability and documentation.

Jan 1, 2002

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By Sherwin F. Kelly

One of the most succinct and illuminating perspectives of the field of geophysical exploration to appear in recent years is an article by E. A. Eckhardt, in the magazine Geophysics for October 1949. Although his review covers the year 1948, many of the data presented are apropos to a review of 1949, and form a pertinent background for a consideration of current progress. He presents charts of the world-wide distribution of gravimeter and seismograph activity in oil exploration, which show that surveys in the United States accounted for practically 68%; of all gravity work and 80%; of all seismic activity. Canada ranked second, with a proportion of roughly 6%, in each case; South America accounted for about the same percentage of seismic work, and double that amount for gravity surveys. Within the United States, Texas and Louisiana were the scenes of the greatest activity, both claiming about 60% of all surveys by each method.

Jan 1, 1950

Comparing Energy Efficiency of Multi-Pass High Pressure Grinding Roll (HPGR) Circuits With increased emphasis on reducing costs and carbon emissions in mineral processing, it is becoming essential to employ the most efficient comminution devices and to use them to maximum effect. High pressure grinding rolls (HPGR) are considered highly efficient compared with other devices, however their relative efficiency in multi-HPGR circuits is less well understood. A series of comminution tests was carried out to evaluate three multi-pass HPGR circuits and a jaw crusher-ball mill circuit. Combinations of HPGR units (1.0 m and 0.25 m diameter), jaw crushers and Bond ball mills were used to grind a 32 mm top size porphyry copper feed (BBWI = 12.1) to a product P80 size of about 150 ¦m. Up to three passes of HPGR were used in each circuit, with energy measurement and size analysis at each point in the comminution process. The energy efficiencies of individual comminution stages and of the overall circuits were quantified and evaluated using three different approaches. The operating work index method for comparing comminution energy efficiency underestimated HPGR performance due to the large amount of fines generated. The -75 ¦m efficiency factor and F50/P50 reduction ratio interpolation methods both give a fairer measure because they better take into account the amount of fines generated by HPGR. The results show that the relative comminution efficiencies of the three multi-pass HPGR circuits tested differ by as much as 22%, providing insights as how to best employ HPGR in a comminution circuit. The most energy efficient of the circuits tested was a three-pass HPGR circuit with a 1.0 m diameter roll on the first pass in closed circuit with an 8 mm screen followed by a second and third pass in a 0.25 m roll.

Sep 13, 2010

By Carlos León, David Estrella, Javier Linares

"Recently, Antamina has completed an expansion program of its operations which increased the thoughput in grinding from acapacity of 109 to 130 ktpd. After commissioning, throughput could be exceeded in grinding and downstream processes but primary crushing became a major bottleneck to the overall production process.With an objective to increase the processing capacity of the primary crusher system, a multidisciplinary team was formed with members of Mine, Concentrator and Maintenance departments, who analyzed the overall context of this process restriction. The main implementations developed were: automatic discharge systems of trucks, logic to count trucks and elaboration of a daily performance report. Following implementation of developed improvements, the numbers of discharged trucks to crusher were increased from 449 to 614 units per day. As a result, the expansion target of 130 ktpd was exceeded and processing capacity was increased from 109 ktpd to 145 ktpd. This improvement adds very significant economical value for Antamina.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and had a nominal 77,000 ktpd mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper and zinc, concentrates are transported by pipeline down to the port of Huarmey. Molybdenum and lead-bismuth concentrates are bagged and trucked to port."

Jan 1, 2013

This method determines tellurium at concentrations down to 0·01 p.p.m., with geochemical accuracy. Tellurium is volatilized from the rock at 800°C in the presence of sulphur from decomposing pyrite, condensed, dissolved, and finally determined by atomic absorption in a long tube burner. The distribution of Te is shown near some gold lodes at Kalgoorlie. Lastly, a method of synthesizing Te-free pyrite from sulphur and ferrous sulphate is described.

Jan 1, 1969

By Guosheng Zhan

The Homestake Mine included the open cut and underground workings up to 2,484 m (8,150 ft) deep. The mine ceased mining activities in December 2001 after 125 years of operation. Pumping from the underground workings continued for 18 more months until June 10, 2003. Homestake had completed a comprehensive hydrologic evaluation on post-closure underground flooding prior to the shutdown of pumping. After closure, the mine was selected by the National Science Foundation as the site for the Deep Underground Science and Engineering Laboratory (DUSEL). An interim laboratory facility will be set at the 1478 m (4850 ft) Level. The final facility will be set at the 2256 m (7400 ft) Level or deeper. Pumping from the underground workings began on June 5, 2008 by the South Dakota Science and Technology Authority (SDSTA). During the period of June 2008 through March 2009, the pumping rate increased from 41 L/s (650 gpm) to 81 L/s (1,290 gpm) with an average rate of 60 L/s (950 gpm). As a result, the water level had been lowered more than 95 m (310 ft). It was found that the observed rebound and later decline to date is in close agreement with the model projections. Because of this, the authors of this paper reject claims of a lack of sufficient measurement devices in place and a lack of understanding of the hydrologic system at the Homestake Mine prior to shutdown of pumping in 2003 (Davis et al, 2009). Furthermore, it is believed that this validated model can serve as a useful tool for the SDSTA to manage future underground dewatering for the DUSEL operation. This paper evaluates the hydrologic conditions in the Homestake Mine area and projects the post-closure groundwater rebound and decline due to DUSEL pumping.

Jan 4, 2010