Search Documents

By Zia Zafir

Design of the deep foundations for the loads imposed by lateral spread include the estimate of the pressure applied by the liquefied material as well as amount of anticipated displacement. In the absence of a non-liquefiable cover over a liquefiable layer, it is possible to design the foundation system just for the additional pressure applied by the flow slides. On the other hand, if a non-liquefiable layer exists above the liquefied zone, the foundation should be designed for anticipated movements. To completely account for liquefaction and/or lateral spread and their interaction with the deep foundation system, a coupled soil-structure interaction (SSI) analysis should be performed. However, a complete SSI analysis may not be feasible for most of the projects. This paper will present recent advances in analysis techniques and simplified methods to design deep foundations for liquefaction and lateral spreading. In addition, a case history of the Rancho California Bridge in southern California located within 1 km of the active Elsinore fault will be presented. One of the bridge abutments is underlain by potentially liquefiable layers. The pressure applied by the liquefiable layer was estimated to be greater than the shear capacity of the 36-inch CIDH piles designed for the abutment. However, with limited ground improvement and more careful analyses incorporating structural effects of CIDH piles, resulting design and construction resulted in a factor of safety greater than 1 against slope failure. The recommended approach was generally consistent with the recently published, and AASHTO sponsored, NCHRP 12-49 project regarding seismic design guidelines for new bridges and the effects of seismic displacements against bridge foundations.

Jan 1, 2006

By L. Ou

This paper reports on research on leaching pyrite in a germ-free system. The effects of mineral particle size, pulp potential and various oxidation agents on pyrite leaching were studied. The results indicated that a smaller mineral particle size leads to a higher leaching rate of pyrite. The optimum results were obtained with a mineral particle size of -0.037 mm. The pulp potential reflected the leaching process and an increasing pulp potential improved pyrite leaching. The leaching rate rapidly increased with the addition of oxidation agents such as Fe3+ and H2O2. However, the precipitate generated by ferric ion coated the surface of the pyrite and prevented further leaching.

Jan 1, 2007

When the first rush of miners took place on the Molyneux River, in the Dunstan Gorge, the gold was won by means of cradling the gravel, which was shovelled from the various beaches and crevices in the rock-bound sides of the river.The above method of winning the gold was only practicable when the beaches were not covered with water, hence the work was usually carried on during the winter months, the ordinary level of the river during spring and summer months being some ten or twelve feet above winter level. The melting of the spow in the Lakes water-shed being responsible for the high summer level of the river.As the available beaches were worked out, other methods of winning the gold were proposed and worked with more or less successful results the first advance being to work the bed of the river by means of a spoon dredge. The spoon was made with a round lip or ring of iron, having a steel cutting edge on one half of the circumference, at the opposite side a socket being forged to take a long spar or boom, which was securely fitted thereto. At intervals round the hoop, half-inch holes were bored to enable. a bullock-hide bag to be laced on to same. The spoon was worked from a pontoon which carried a crab winch, tackles and the necessary washing appliances to treat the washdirt lifted. In starting to dredge, a tackle was attached to near the upper end of the boom, and a line or chain was carried over a cat head from the crab winch...

Jan 1, 1901

By O. Bernal, G. Velarde

Sociedad Minera Cerro Verde, majority owned by Phelps Dodge produces 200M lbs per year of LME Grade A copper from low cost leaching of secondary sulfides and SXEW processing. Central to the success of Cerro Verde has been the continuous improvement of leaching practices which currently yield over 80% recovery of the contained copper in the ore. This recovery has been achieved by careful attention to operational practices and leaching process fundamentals. This paper details the development of the concept of “Lixiviant Request Rate” where by solution is applied at an optimal rate for the grade, mineralogy, and the point in the leach cycle. Also paramount to the success of Request Rate technology has been the development of irrigation practices such as drip irrigation and irrigation grid design. These developments have ultimately resulted in improved copper production, decreased sulfuric acid and water consumption, decreased pumping cost, and more consistent PLS grades.

Jan 1, 2004

By Charles Pretorius, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge.

Jan 1, 2006

By G. Thodos, W. F. Stevens

The point-source function introduced by Horner' us a solution to the general unsteady-state equation for the flow of fluids through porous media has been utilized to calculate pressure profiles for adjacent wells as a function of time. By trial and error, the time at which the pressure waves meet to cause interference can then be calculated. For this calculation, the time of interference is arbitrarily defined as that time when both pressure waves exhibit a pressure decrease of 25 psi ar the same point within the formation. To illustrate the method, an example involving two adjacent wells producing at different rates has been worked out and is presented in detail. INTRODUCTION The initiation of production of a new well is usually accompanied by pressure drawdown measurements in order to establish the extent and characteristics of the formation. The interpretation of such pressure drawdown data is based on mathematical developments involving a single well in an infinite reservoir. If more than one well is present in a reservoir, the possibility of interaction between wells exists. Therefore, care must be taken in interpreting the pressure drawdown data. It becomes important to be able to determine when this interaction, or interference, becomes significant. This paper presents a method for the prediction of the approximate time of interference between two such adjacent wells. The basic differential equation describing the pressure distribution existing during unsteady-state flow of a slightly compressible fluid has been solved by Hor-ner.' for a constant production rate from a circular homogeneous reservoir of infinite extent. The solution utilizes the point-source function to define the pressure at various points within the formation as a function of time. The resulting expression is: q = production rate, STB/D ,;= formation volume factor, dimension-less µ = fluid viscosity, cp k = formation permeability. md H = formation thickness, ft C - fluid compressibility, psi' F = formation porosity, dimensionless R = distance from centerline of well, ft T = production time, hours Ei(—u) = Ei-function of U Eq. 1 may be used to calculate the pressure profiles generated during production from a single well in an infinite reservoir.

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

By Jose Luis Sosa, Marco Surichaqui, Ramirez Marcelino

El proyecto permite obtener resultados de operación que no siempre son los esperados en cuanto a calidad y recuperación, aquí es donde destaca el programa; tiene una data que PRONOSTICA estos resultados, con el control de parámetros, corrigiendo estos resultados al valor óptimo esperado, haciendo que su empleo permita obtener en “tiempo real” excelentes resultados en cuanto a calidad y recuperación del licor lixiviado y se refleja en costos.

Sep 1, 2017

By L. Connolly, F. R. De Luca

"Rubber liners at Denison Mines Limited are used in 10 1/2x 24' low discharg0 pebble mills. These were originally 10 1/2 x 13 Dominion overflow type ball mills. Experience here shows that the wear of rubber and ni-hard lifters is approximately the same in the feed end half of the mill, while the wear of rubber lifters is much greater in the discharge half. The wear of rubber plates is considerably less than white iron in the feed end half of the Mill and slightly more in the discharge end half of the Mill. Rubber components are lighter to handle but their installation is time consuming. This leads to the conclusion that a combination of ni-hard lifters a~~ rubber plates is the most economical compromise in Denison's case, for the Mill. Rubber discharge grates are superior to steel grates, while steel feed end liners are superior to rubber.The Use of Rubber Mill Liners at Denison Mines LimitedGrinding is done in two identic0al circuits each consist-ing of one 10 1/2 x 14' Dominion overflow rod mill, two Dorr Oliver quadraplex rake type classifiers, two 10 1/2 x 24' Dominion low discharge grate pebble mills and ancillary pumps and conveyors for pebbles. There is one centrally located distributor box that receives the discharge of the 4 pebble mills and splits it out to the classifiers."

Jan 1, 1974

By Nick Poushinsky

OVERVIEW OF PRESENTATION ?Stantec?s Northern Presence ?Challenges for Northern Development ?Environmental Approval Challenges ?History/Expectations ?Baseline Data ?Consultation ?Regulatory Processes ?Extra ?Regulatory ?Keys to Success

May 1, 2009

By P Steinier

Most operations, when considering their comminution circuit, are primarily concerned with achieving the desired particle size distribution to obtain adequate liberation for the separation process, at minimum cost. Invariably, the effect the grinding media has on the subsequent separation process (ie flotation, leaching) is not taken into account when selecting the media. This choice is driven by cost rather than metallurgical outcomes. Maximising valuable mineral recovery, with optimum selectivity against gangue minerals, is about good particle preparation. And, particle preparation is strongly related to achieving adequate mineral liberation with the correct pulp chemical conditions. However, the pulp chemistry of a system is largely ignored and relies heavily on pH control and the addition of appropriate reagents (collectors, frothers, activators, depressants). The changes effected by the addition of the various reagents are obtained through conditioning the ground pulp prior to or during the concentration stage, subsequent to grinding. Frequently, reagents are added during grinding with good effect, but the impact of the grinding media on down stream processing is usually overlooked. A number of case studies examining the effect of grinding media on pulp chemistry and subsequent flotation performance were completed on several different sulfide mineral systems (for example, lead/zinc, copper, refractory gold). The evidence suggests that a change in grinding media type from forged to high chrome (ie conditioning the pulp during grinding) resulted in a shift in pulp Eh to less reducing conditions, an increase in the dissolved oxygen content of the pulp and a reduction in the iron species present. The changes have a positive impact on flotation behaviour. The results of the case studies are discussed.

Jan 1, 2004

A massive cobalt-containing pyrite orebody occurs in banded albite-quartz-biotite rocks at Thackaringa, some 30 km SW of Broken Hill. Because of the world-wide shortage of cobalt during the late 1970s, serious consideration was given to the development of a suitable flow-sheet to recover the cobalt from this ore. Details of a pressure leaching process in which more than 90 per cent of the cobalt is extracted from a pyrite concentrate are presented.

Jan 1, 1983

By Christian J. Sorensen, Christopher Armstrong, Andrew Matejunas

A team consisting of junior and senior mechanical engineering students at New Mexico Tech worked on the design of an explosively loaded vessel, with a maximum load of 15 grams (0.53 oz) TNT equivalent explosive. The main challenge presented was to meet the stringent sample positioning specification of 3 microns in two Degrees Of Freedom (DOF) and one degree of rotation in a third DOF. This is to accommodate precise sample placement in a tight x-ray beam, and to bring areas such as explosives/metal interfaces into magnified field-of-view photography. This presentation describes the process and design decisions to arrive at the final product presented to LANL in December 2014. Our engineering analysis techniques will be reviewed, including use of American Society of Mechanical Engineers (ASME) Boiling & Pressure Vessel Code (BPVC) Code Case for Impulse Loaded Pressure Vessels (ASME BPVC Code Case 2564-3). Also discussed will be integration of Hydrocode computer models with Finite Element Method analysis.

Jan 1, 2015

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

By Boris Chacón

Durante el desarrollo cotidiano de una operación minera, se obtienen diversos tipos de información como: muestreo, perforación diamantina, etc. las cuales, se originan en base a observaciones de campo. En ese sentido, es vital desarrollar procedimientos adecuados que permitan administrar la información compilada. Por ello, el presente trabajo señala la aplicación de la administración de datos geológicos en la empresa minera Iscaycruz. La información de datos geológicos se puede administrar en formatos tipo gráfico o en bases de datos, por lo cual se requiere que la estructura de almacenamiento de dichos formatos contenga parámetros previamente analizados. Asimismo, es necesario que el equipo de trabajo organize la base de datos, a través de los objetivos y metas trazadas, así como de la verificación y análisis de los resultados, para mantener actualizada la información.

Aug 25, 2002

By D. M. Wyslouzil

"This paper was prepared for presentation at the 16th Canadian Mineral Processor's Annual Meeting, Ottawa, Ontario, Jan. 17 to Jan. 19, 1984.This paper gives an account of the development of treatment procedures for the differential flotation of refractory copper-zinc ores. Special references are made to the effectiveness of various zinc depressants and their combinations.Studies carried out on refractory copper-zinc ores demonstrated that conventional zinc depressants such as cyanide and zinc sulphate were not particularly effective when secondary copper minerals were present in the ore; the flotation activity of sphalerite was enhanced in the presence of cyanide.Among the various zinc depressants evaluated, the following depressant combinations were found most effective: Zn(OH) 2-S02 , 802-CaO, Na2S-Na2S03-S02, Na 2 S-S02 and Na 2S-S0rDS22.The practical application of any of these systems depends on the type of ore treated and other conditions such as pH, levels and points of collector and depressant additions.In this paper the effect of each depressant combination on different ores is described with reference to the selection of collectors."

Jan 1, 1984

By Pablo Velasco

After becoming an oil exporter in 1972, Ecuador experienced a remarkable economic upswing until 1978. However, in 1979 and 1980, a combination of only slight improvements in agricultural output and stagnating petroleum output lowered rates of real gross domestic product (GDP) expansion to 5.3% and 4.3%, respectively. In current prices, the GDP in 1980 was estimated at $11.3 billion.2 The slowdown in growth is attributable in large part to the low level of petroleum exploration in the 1972-79 period. Ecuador's production of petroleum declined 4.5% in 1980 compared with that of 1979. The consortium of Corporación Eatetal Petrolera Ecuatoriana (CEPS), the State oil company, and Texaco, Inc., operating in Ecuador's eastern jungle region was responsible for nearly all of 1980 production, The volume of total crude petroleum exports from Ecuador dropped from 44.7 million barrels in 1979 to 40 million barrels in 1980, although crude petroleum export revenues rose from $1,032 million in 1979 to $1,294 million in 1980- The latter figure represented 54% of Ecuador's 1980 merchandise exports. Crude oil exports accounted far about 46% of the value of 1979 merchandise exports. The total nonfuel mineral exports in 1980 were valued at less than $1 million.

Jan 1, 1982

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

By Andre Vervoort

Falls of ground, such as falls of roof and sidewall collapses, are a major cause of fatalities and injuries in South African collieries. Based on information obtained from the accident reports of the various Chief Inspectors of nines, a statistical analysis was conducted covering the period 1970 to 1988. This study shows that the volume of rock in a fatal fall of ground is often quite small. In intersections, fatal falls are on average larger than in roadways and at the face. It was also found that in 36 % of all fatal falls of ground no temporary or permanent support was installed at the site of the accident.

Jan 1, 1990

An active list of permissible explosives was published in December 1936 as part of Bureau of Mines Report of Investigations 3324, under the title "Active List of Permissible Explosives and Blasting Devices Approved Prior to July 31, 1936." This list included 170 brand names. Changes in the list that have been authorized to June 30, 1937 placed 35 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Ten permissible explosives were transferred from the active to the inactive list. The present list contains 196 brand names, one explosive having been placed on the list subsequent to June 30, 1937. The brand names of the permissible explosives placed on the active list are as follows:

Jan 1, 1937