Search Documents

By Taeyong Lee, Cole Bales, Matt Fowler, John Horne

Mitchell Point Tunnel near Hood River, Oregon is one of the more unique segments of the Historic Columbia River Highway and State Trail being constructed through the Columbia River Gorge. This 650-foot bike/pedestrian tunnel set to open in 2024 is being delivered by FHWA in partnership with Oregon DOT, Oregon State Parks, and the U.S. Forest Service. Primarily driven using drill & blast excavation methods through basalt, the shotcrete and dowel-supported tunnel features masonry portals and ve window adits that provide illumination and views of the river similar to the original highway tunnel of many vistas built in 1915 that was removed in 1966 to make way for Interstate 84. This paper summarizes the planning, design, and construction.

Jun 23, 2024

By Lowell Stroud

Ten natural gases containing from 0.023 to 8.4 percent helium were investigated. In seven high-helium samples, the isotopic abundance of Ne21 was greater than in the atmosphere, being supplemented by 33 to 85 percent of "excess" or "radiogenic" Ne21. The ratio of He4/Ne21(rad) in these gases was evaluated and found to vary between 2.9 x 107 and 5.9 x 107 , a factor of approximately 2. Argon concentrations were determined by the isotope dilution method. The isotopic ratios of Ar40/Ar36 in the high-helium gases were from 5 to 75 times the atmospheric value, with the Ar40 being about 80 to 99 percent radiogenic in nature. The ratios of He4/Ar40(rad) in all 10 gases were evaluated and found to range from 4 to 18. The isotopic ratio of N14/N15 in four of the high-helium gases was essentially the same as in the atmosphere; in three cases it was approximately 5 percent higher than the atmospheric value of 272.0. The genesis of nitrogen and the relationship of nitrogen to helium in natural gases were reviewed and are discussed in terms of a theory for the concurrent generation of nitrogen, helium, radiogenic neon 21, and petroleum (hydrocarbon gases and liquids).

Jan 1, 1967

By Jacques F. Abrahamse, Kevin A. Bahe, T. Arthur Palm, Gregory E. McCluskey, Stephen L. Bessinger

Introduction Basis For System San Juan Coal Company (SJCC) is a subsidiary of BHP Billiton. Until recently, BHP Billiton operated three surface mines in northwestern New Mexico: Navajo, San Juan, and La Plata. The San Juan and La Plata Mines supplied the San Juan Generating Station operated by Public Service of New Mexico. Stripping ratios at those operations were increasing, and by 2000 a feasibility study was underway to develop SJCC’s vast underground reserves as a replacement. Early in the evaluation and planning phase for the San Juan Underground Mine, it was determined that the target seams (Fruitland #8 and #9) had a high propensity for spontaneous combustion. Spontaneous combustion was identified as a risk, both to personnel and equipment, and to the ability of SJCC to reliably fulfill its obligation to the power plant. In the last 20 years, several western US coal mines suffered underground spontaneous combustion events and/or mine fires. Included in this group were Colorado Westmoreland’s Orchard Valley Mine (1987), RAG’s Willow Creek Mine (1998 and 2000), Oxbow’s Sanborn Creek Mine (1999), the West Elk Mine of Arch Coal (2000), Arch’s Skyline Mine (2002), Western Fuels’ Deserado Mine (1996), and the West Ridge Mine of Andalex Resources (2003). The cause for the majority of these fires was spontaneous combustion. Fighting the fires required injection of an inert gas or foam. Nitrogen and carbon dioxide were the predominant choices of inert gas. In all cases, the gasses had to be trucked in from considerable distances. Before the inert gas could be used, injection holes had to be drilled into or near the suspected fire locations. This drilling and trucking caused costly delays in the timing of the fire fighting effort, and was not as precise as desirable. Emergency purchasing of gas and pumping services was extremely expensive, running as high as $70,000 per day at one mine. As a result of the experience of other western US coal operators, and the risk inherent with spontaneous combustion at SJCC, it was decided to pursue installation of a nitrogen delivery facility on-site at SJCC. This decision was later expanded to include a continuous supply of nitrogen.

Jan 1, 2005

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By G Fahey, S Rose

"Mining geology as a defined profession is only about 100 years old. The successful modern mine geologist needs to be a multidisciplinarian, but also needs to maintain a focus on the key outputs of the role. The technical skills needed in the role have increased as mining methods move to increasingly mechanised techniques. As well as being the guardian of the orebody and ensuring minimal dilution to expected ore grades, the mine geologist should be competent in the 12-point mine geology process. The mine geology process should include:a statement of purpose (a ‘mission statement’)geological mapping/logging system that supports consistent and regular geological data collection, storage, and interpretationsampling system that can produce representative samples and fits in with the mining scheduleassay database with relevant controls to ensure only ‘clean’ data is loadedsimple quality assurance / quality control (QA/QC) system for samples and assays, with a response process to react to out of specification resultsconsistent method of exporting, visualising, processing and interpreting assay data to create mining blocksdevelopment sign-off system so that all development and stoping is controlledproduction tracking system to monitoring and reporting what ore and waste volumes have been moved from the face, to any intermediate stockpiles, the run-of-mine (ROM) pad and into the crusherreporting system for daily, weekly and monthly reporting of tonnes and gradesdocumentation so that the grade control system has simple, but effective descriptions of how it works, who has responsibilities, and authorities, and be easily maintainedreconciliation system to compare resource and reserve to grade control and to mined and milledtraining system so that the geology team can quickly become competent.In this paper, the authors discuss the requirements of each point, and comment on common shortfalls observed by them over several years’ experience on producing mines worldwide.CITATION:Rose, S and Fahey, G, 2014. Modern mining geology, in Proceedings Ninth International Mining Geology Conference 2014 , pp 461–466 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By Andrew J. Petruska, Austin F. Oltmanns

The paper proposes a capacitive load cell for detecting changes in material and tool wear conditions for conical picks used in underground mining. The current process is dangerous and subjective, relying on human operators near the cutting interface. The new sensor aims to improve worker safety by allowing operators to perform their functions from a greater distance.

Aug 1, 2023

By N. Paas

Diesel powered equipment has been operated in underground coal for more than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trona, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment.

Jan 1, 1997

By M Singh, R C. Steinhaus, J J. Rust

Metallurgical process control systems in mineral plants often employ state-of-the-art monitoring analysers in an attempt to optimise plant operations and enhance mineral recoveries. These systems are unfortunately invariably fed by simplistic ‘sampling’ designs consisting of various in-stream methods or pressurised probes. These are unfortunate compromises and provide a false picture of what a mineral flotation or other process can achieve. The situation is further aggravated by some manufacturers using misleading marketing to suggest discrete cross-stream methods for metallurgical accounting and unreliable continuous in-stream off-takes for control sampling and that they are of synonymous integrity.Reliable, absolute or representative samples are often absent in many modern day concentrator plants, due to compromises around sample taking, particularly in terms of delineation and extraction errors and thus leading to sample bias. For more reliable information from online analysers we need a continuous, but much more reliable sample taken, than is current practice.Online analysers require a fully proportional and continuous supply of sample for effective process control, otherwise maximised or benchmark recoveries will be nothing but a pipe dream. Large discrete cross-stream samples from mechanically less reliable equipment cannot be used as feed to online analysers, as it will negatively impact real-time feedback and efficient process control.It is possible to build correct sampling systems that could do both process controls online and metallurgical accounting at the same time. Multotec Process Equipment (Pty) Limited, in close association with experienced sampling consultant Francis Pitard, have jointly patented a concept to achieve this and which is embodied in the design of the unique Rotating Cone® Sampler (International Patent Application No. PCT/IB2016/057464). This versatile unit for dry and wet applications has high division ratios via two-step sampling and division.A prototype was built and tested to validate the design and levels of precision achievable when employing the unit to split dry mineral fines or even certain foodstuffs.CITATION:Steinhaus, R C, Rust, J J and Singh, M, 2017. Does process control sampling always have to be a compromise?, in Proceedings Eighth World Conference on Sampling and Blending , pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By A. E. Schwaneke

Plans and specifications are given for constructing a quartz composite oscillator designed to measure internal friction in metals and alloys . The characteristics of the system are listed , and detailed procedures for its operation are explained . Typical measurements on manganese - copper alloy , on single - crystal magnesium , and on polycrystalline magnesium are shown to illustrate applications of the system .

Jan 1, 1964

By Arthur S. Cornford

According to Arbiter (Reference 1), the ball mill was invented by Brückner in Germany in 1876 and was first used in the United States on ores about 1905. The basic concept was a simple rotating cylindrical drum in which the tumbling action of the charge of material and grinding media resulted in size reduction of the material. Despite the very low mechanical efficiency of this method a number of factors have caused the tumbling mill to remain, by far, the most widely used piece of equipment for mineral grinding. The principal factors influencing this situation have been simplicity of design, ease of manufacture, ready adaptability to familiar material handling layouts and the absence of practical alternatives acceptable to the industry. In the early mills, the material was ground in batches, the mills being charged and discharged through doors in the shell. The shell was supported by means of solid trunnion shafts resting in plain bearings and the drive was accomplished through one of these shafts. In some later batch mills, the mill shell was supported on rollers which were also used to drive the mill. At an early stage, continuous operation was made possible by feeding and discharging the mill through hollow trunnions, the method still in most widespread use. The mechanical and structural design of the early mills was not an onerous engineering task. Norse sense and good practical knowledge were key qualifications. The mill shells had to be heavy enough to withstand the physical abuse they would receive in the field and the bearings had to have low enough unit pressures and sufficient wear retol to ensure several months of operation before the need for replacement occurred. When these requirements were satisfied, stresses developed in the equipment during operation were insignificant and the majority of structural failures were probably due to the use of inferior materials in manufacture. Over the years, the ever present demand for increased productivity has resulted in a steady Increase in the size of units of production equipment, including grinding mills. Arguments have been presented elsewhere, for and against the Idea of a high throughput single line grinding operation as opposed

Jan 1, 1972

By H. Kenworthy

Laboratory experiments were conducted on several materials to determine their suitability for the production of mineral wool. By blending raw charges in the proper proportions and in some instances by adding lime, acceptable wools were made from samples originating in Alaska, Florida, Texas, and Virginia. It was shown that satisfactory wools can be produced from many kinds of raw materials if the ratios of acidic and basic constituents are properly maintained. INTRODUCTION The Federal Bureau of Mines has facilities at the Mississippi Valley Experiment Station, Rolla, Mo., for examining and testing mineral-wool raw materials. Samples are evaluated through small-scale wool-blowing experiments, aided by petrographic, chemical, and physical analyses of the raw materials and finished wools. When enough experimental data have been accumulated they are made public through Government reports and periodicals. This report of investigations follows that published in 19513/ and presents test data on samples received and examined since 1951.

Jan 1, 1956

By K J. Kidd

There is general understanding of hoisting systems throughout the mining industry. However, the relative importance of the various parameters influencing hoist selection and utilization is not completely understood. In order to determine if these parameters can be identified and prioritized, data covering 613 hoist installations were compiled. The 613 installations represent hoisting systems in 30 countries on six continents. This study compares data to historical trends, correlates design parameters in an attempt to identify underlying selection criteria, and comments on the apparent trends in recent developments in hoist design.

Jan 1, 1998

By LUDWIG VOGELSTEIN

WE are indebted to Mr. Barbour for his valuable contribution to the literature on copper statistics; it is to my knowledge the only intelligent attempt to throw light on a much misunderstood subject. If I should appear to criticize some of his findings and arguments, I do not want to leave the impression that I do not appreciate the article; I think Mr. Barbour has been painstaking, and even where one might not agree with his conclusions, he has opened our eyes and stimulated us in our search for the truth.' It might be well to define the term "secondary copper" and to make a few remarks about the origin and the reasons for the variation of the supply. Mr. Barbour has touched on these points, but not sufficiently to make them clear to those not in the business.

Jan 1, 1931

By Steven J. Page

Accurate measurement of workplace respirable dust concentration is an essential step in eliminating lung disease in any occupational setting. In the United States (U.S.) coal mining industry, this measurement process has relied upon a personal sampler that includes a 10 mm Dorr-Oliver (DO) nylon cyclone operated at a flow rate of 2.0 L min-1 to collect a respirable dust sample. Dust concentrations measured with this sampler are multiplied by 1.38, which was empirically derived, to convert them to measurements approximating the United Kingdom British Medical Research Council (BMRC) definition of respirable dust upon which the health effects of coal mine dust are based. The International Organization for Standardization (ISO) subsequently refined the respirable dust definition and the U.S. National Institute for Occupational Safety and Health (NIOSH) 1995 Criteria for a Recommended Standard presented a conversion multiplier of 0.857 to apply to the 2.0 L min-' DO (in addition to thel.38 multiplier) to obtain equivalent ISO concentrations, as approximated by the 1.7 L min-1 DO. However, the conversion multiplier 0.857 was derived indirectly from a limited size distribution data set rather than a direct comparison of the DO samplers. The present analysis focuses on providing a more accurate conversion multiplier derived from direct comparisons of the 2.0 L min-1 (with 1.38 BMRC equivalency multiplier) and 1.7 L min-1 DO cyclones. A weighted linear regression analysis of this database suggests that a more accurate estimate of the conversion multiplier is 0.815.

Jan 1, 2009

By C. Liu

Corrosion behavior of the stir zone in a friction stir weld of dissimilar A12024/AZ31 alloys was investigated in the immersion test in distilled water (pH=6) for different times. Microstructures and the distribution of chemical elements were analyzed by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Due to the difference in the corrosion potentials between A12024 and AZ31, the AZ31 alloy constituent in the stir zone was susceptible to the corrosion attack in the distilled water. The corrosion attack was found to occur in the narrow region of the AZ31 alloy adjoining the A12024 region, where there was a low ratio of anode-to-cathode surface area. The corrosion attack became more severe in the AZ31 alloy regions with increasing immersion time. The A12024 alloy region in the stir zone of the weld was protected by cathodic reactivity due to sacrificial anode AZ31 alloy.

Jan 1, 2007

_What is standard technology infrastructure _ Business Context _ The mine operator?s technology challenges and needs _ The benefits of technology standards _ Overview of the SMART initiative _ Technology standards description _ Current status _ Next steps What is Standard Technology Infrastructure Technology Infrastructure is: ? Networking communications ? Computing operating systems ? Hardware platforms ? Data storage and access ? Operator interface _ These components are based on recognized open standards organization, and _ Commonly and widely utilized by industry, and _ Commercially available off-the-shelf systems (COTS), both hardware and software _ Standard capability to provide immediate and open access to raw or derived data at source, APIs, configuration parameters & sub-routines from all system components; ALL CURRENTLY AVAILABLE

May 1, 2008

By C. Holmes, T. Holmes

Engineered-in material handling problems are responsible for significant unrealized value in mineral processing plants. At the root, is a lack of awareness and understanding of bulk material handling science and how important it is, especially in early design stages. Mineral processes add value to mined raw feedstock through physical and chemical transformations in unit operations, but only if the material can flow through them. Essentially, each unit operation receives a unique feedstock and produces a unique product to be collected, transported, and fed into the next unit operation. Such material-handling systems can only be expected to achieve design throughput if the system equipment is designed to the materials’ characteristics, over their full range of conditions. This requires quantification of flow properties to support the necessary customized equipment designs. Too often, assumptions or “library values” of a material’s properties are used as the basis for flow modelling and conceptual, and sometimes even detailed, design. This is especially true for hazardous materials like uranium ore, for which the additional precautions, costs, and time necessary for safe handling are often used to rationalize postponing or even bypassing testing. The surprises that often transpire in the wake of insufficient material handling consideration can have acute and costly effects. Fortunately, there is a better way.

Jan 1, 2020

By K. Hausmann, P. A. Sashin, G. J. Prejean

Misfires caused by unreliable shock tube constructions can have significant cost implications and place field workers at serious risk during remediation. Ionomer materials, used as a subtube in shock tube constructions, provide superior hot tack strength, oil resistance, impact resistance at cold temperatures and excellent thermoformability properties. These are important features for resisting blast-throughs and ensuring blasting reliability in demanding environments, such as open pit mining in harsh environments. Superior hot tack strength, strain hardening, and excellent thermoformability properties of the ionomer materials ensure uniform powder distribution along the shock tube during construction and avoid undesired powder accumulation due to deformation or vibration during use. Oil or chemical resistance is another feature of Ionomers. This allows improved property retention in contact with oils and hence longer sleep times of the shock tube. Another feature of these highly engineered ionomers is superior impact strength at low temperatures. This plays an important role considering the resistance to fly rock impact in open pit mining operations in particular in cold climates.

Jan 1, 2011

By Renan Oss Giacomelli

A adesão de revestimentos multifuncionais em substratos moles é de extrema importância para o comportamento tribológico desta importante classe de tratamentos superficiais. Mais especificamente, testes de indentação e de riscamento são bastante utilizados na medição desta propriedade. No presente estudo, a adesão de filmes de DLC do tipo a-C:H depositados em aço baixo carbono nitretado foi investigada através de testes de indentação e riscamento. Os revestimentos foram produzidos através de PECVD em substratos de aço 1020 com dois acabamentos superficiais: lixado (Sq = 0,184 µm) e polido (Sq = 0,002 µm). Foram realizados testes de indentação Rockwell C e a adesão foi quantificada através da medição da área desplacada em imagens obtidas através de microscopia ótica. Esta análise produziu resultados semi-quantitativos, eliminando a análise qualitativa subjetiva sugerida pela norma VDI3198. Ainda, testes de riscamento foram realizados nas mesmas amostras com o mesmo indentador para que uma comparação entre ambas as técnicas pudesse ser estabelecida. Por fim, o método apresentado mostrou resultados coerentes, onde amostras com menor carga crítica apresentaram uma maior área desplacada. Amostras lixadas apresentaram um desempenho inferior em relação a adesividade.

Aug 16, 2017

By Yoshinobu Fukumori, Testuya Watanabe, Futoshi Shikata, Hiroyuki Tokumitsu, Hideki Ichikawa, Masahito Miyamoto

Nano-particulate systems have attracted much attention recently in pharmaceutical field as drug carriers and functional components of pharmaceutical dosage forms. This paper describes our approaches in design and preparation of nano-particulate systems, including lipid nano-emulsions, chitosan nanoparticles and thermosensitive acrylic nanoparticles, for certain pharmaceutical applications mentioned below. The lipid nano-emulsions with their particle size smaller than 100 nm were prepared for gadolinium neutron-capture therapy (Gd-NCT) of cancer by a thin-film hydration method with sonication, and intraperitoneally injected into Greene's melanoma (melanotic No. 179)-bearing Syrian hamsters. This provided such a high gadolinium concentraton in tumor as 107 µg/g tumor (wet basis) at 48 h after administration. As an alternative gadolinium nano-carrier for Gd-NCT, biodegradable and highly gadopentetate-loaded chitosan nanoparticles (Gd-nanoCPs, 426 mTI in particle diameter and 9.3% in Gd content) were prepared by a novel emulsion-droplet coalescence technique. A significant tumor-killing effect could be obtained when Gd-nanoCP suspension was injected intratumorally twice 24 and 8 hours before neutron irradiation into B 16Fl O melanoma-bearing mice and subsequently thermalneutron was irradiated toward tumor site with a flux of 2 x 109 n/cm2/sec for 60 min. As one another application of nanoparticles, a novel acrylic composite latex with a hydrophobic core and a thermosenstively swellable shell was designed for fabricating microcapsules showing thermosensitive mode of drug release. The microcapsules with the composite latex-dispersing membranes exhibited an exceptionally rapid on-off response of drug-release in a thermosensitive manner.

Jan 1, 2000