Search Documents

By R. M. Bird

Few persons outside of the foundry trade have any conception of the great variety of sands now regularly specified and furnished, nor of the differences in foundry practice frequently resulting from apparently minor changes in sands. Conditions in each locality where the sands are mined and prepared necessitate special equipment designed to perform the work efficiently. The description that follows of the foundry-sand producing operations is typical of the areas in New York and New Jersey, and particularly refers to the operations of the George F. Pettinos Co. A few years ago the so-called Albany sands were dug by simple methods and hauled by horsecart to railroad. Depletion of sand near railroad sidings and extended use of automotive power have appreciably extended the area from which sand is now being dug. It is not unusual to haul 5 miles to the railroad. As stripping is quite shallow, 6 to 18 in., and the banks of usable sand generally run from 12 in. to 4 ft., it is economical to work the bank by benches so narrow that the overburden can be thrown by hand shovel to the exposed bottoms. In effect the top soil goes back to where it was, but on a lower level. Consequently the general surface appearance of a mined acreage is the same as before. This condition is in fact cutomarily required when a farm owner sells his sand in the ground. After such replacement, in the course of 3 to 5 years the soil is no less fertile than it was before mining. The sand itself varies as to grain and bond vertically and also along the breast. No mechanical equipment has been developed to compete with hand shovels and no machine has as yet been devised that grades the sand as required. Uniformity of sand, as shipped, depends first, last and all the time on the man on the job. Mixing equipment can change the appearance of the sand and mask its lack of uniformity, but it will never correct wrongly graded sand, dug from the bank. Modern methods of testing are helpful in setting up standards against which the man in the bank can compare his sands, but a good bank foreman is the only assurance that the sand, as dug, matches the required sample.

Jan 1, 1926

By A. L. Labbe, J. J. Donoso

Hard-won experience in the operation of smelting plants has pointed the way to the most efficient design and economical operation of a baghouse system for recovery of metallurgical fumes. This paper treats of the principles governing bag filtration and the factors most directly affecting bag life. Methods for temperature conditioning of smoke previous to filtering are described and the evolution of bag shaking mechanisms is brought up to date. THE history of the bag filter process, as applied to the recovery of metallurgical fumes, goes back to 1876, when the Lone Elms Works of Joplin, Missouri, erected a two-section baghouse for filtering fumes from Scotch Hearth lead smelting furnaces. By modern standards this installation was crude, but the basic operating principles remain essentially the same today. Great progress, however, has been made in the mechanization of the process by the use of devices for mechanically and automatically cleaning bags of adhering fumes, in the use of instruments for recording and controlling the variables affecting baghouse operation, and in the conditioning of the smoke previous to filtering. The principles governing bag filtration of fumes were investigated in 1929 by A. J. Seitz of American Smelting and Refining Co., and he arrived at the following conclusions: 1. Pressure on Bags at Constant Volume: The rate at which the pressure builds up in a bag with constant volume is directly proportional to the time, with the same kind of smoke and dust burden (fig. 1). 2. Pressure on Bags for Change in Volume: With equivalent smoke and dust burden, the bag pressure increases with the square of the increase in volume. The rapid increase in pressure is due to (1) increase in volume, (2) increase in amount of dust on the bag, and (3) more intense packing of the dust at higher velocity (fig. 2). 3. Effect of Intensive Filtering on Pressure: Since the pressure builds up directly as the square of the volume, with the same smoke and dust burden, it is necessary to shake the bags in that increased ratio, and vigorously, to keep the pores of the bag open and pressure down. This increases the wear on the bags and the dust losses. 4. Effect of Shaking on Dust Losses: The losses are in direct proportion to the frequency of shaking because the loss takes place immediately after shaking, before the bag seals itself. Tests show that with hand shaking the last 20 pct of the removable dust requires seven times more shaking per unit weight of dust than the first 80 pct. 5. Effect of Fineness of Dust on Losses: The fineness of the dust particle increases the loss in two ways: (1) When the bag is clean a greater percentage of it will pass through before the bag seals itself; (2) fine material penetrates farther into the bag pores, building up pressure faster and necessitating more shaking, thereby increasing the loss. The physical principle of operation of the bag filter is simply the separation of solids from a gaseous carrier through a porous medium, and is analogous to the filtration of solids from liquid carriers. Basically, the mechanics of the process are as follows: Fume-laden gases drawn from the operating fur-

Jan 1, 1951

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson's ratio, and Young's modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young's modulus, s is Poisson's ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman's measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958

By G. E. Johnson

The problem of efficient reclamation of zinc base die cast scrap became interesting early in 1930. Die Cast Metal, as referred to in this paper, is a zinc base alloy with various proportions of aluminum, copper, magnesium, antimony and tin. Many attempts were made to work out some means of reclaiming the discarded die cast metal for re-use as new die cast metal. Difficulties in such reclamation were attributable to contamination by lead and tin from solder, chromium and nickel from electroplated coatings, and iron from iron inserts. This paper relates the experiments that led to the development of a specialized muffle furnace for the treatment of zinc base die cast scrap for the production of zinc oxide and zinc, and describes the development of the muffle furnace and the equipment now used commercially for these purposes. The Eagle-Picher Co. acquired all patent rights' for these developments from the International Smelting and Refining Co. in connection with their purchase of the East Chicago Plant. Zinc Base Serap Situation About 1935, the die cast scrap situation became increasingly acute for scrap dealers. This scrap was accumulating from dismantling automobiles and household appliances which contained die cast parts. Efforts to find an outlet for this type of scrap were intensified. The International Smelting and Refining Co. began to study the possibilities of a commercial process for the recovery of values from die cast scrap. At that time most of the die cast metal reclaimed was melted down in small kettles of from one to five tons capacity, the iron inserts being removed by skimming. The dross was skimmed off and disposed of as a zinc dross. The drossed metal was cast into slabs and was given the trade name "die cast slabs.". Distribution of the products produced by melting die cast scrap in kettles is shown in Table 1. American Process Experiments A method considered for the production of zinc oxide from die cast scrap was an adaption of the standard American Process of zinc oxide manufacture. Thus some die cast scrap was mixed with oxidized zinc materials and charged to Wetherill grates. The zinc oxidized to zinc oxide but, while the aluminum and copper largely remained in the residue, the color of the zinc oxide produced was impaired by copper contamination. As the proportion of die cast scrap was increased, liquation took place; that is, the metal trickled through the charge then solidified in the openings of the grates. French Process Experiments Several hundred tons of die cast scrap were purchased for test purposes and converted into die cast slabs. These slabs were charged into a French Process (horizontal retort) zinc oxide furnace with some electrolytic zinc. A satisfactory grade of zinc oxide was not produced. Distillation in Belgian Retorts It was then decided that, rather than attempt to use scrap die cast metal or scrap zinc for the production of zinc oxide, it would be advisable to redistill the die cast slab metal in a Belgian retort furnace. The opportunity to do so was provided by the closing of the zinc smelter of the Illinois Zinc Co. at Peru, Ill. Arrangements were made for the operation of a Belgian retort furnace for such redistillation purposes. The results of this experiment are summarized in Table 2.

Jan 1, 1950

By H. B. Heller, T. J. LaChapelle

Phosphorus nitride has been used as a diffusant for introducing phosphorus into silicon under various conditions. It has a temperature -dependent rate of decomposition beginning in the 500°C range, increasing very rapidly above 1000 C, producing gas -eous phosphorus and nitrogen. Best control was obtained with a two-temperature arrangement, with silicon at the proper higher diffusion temperature. It is an easier compound to use than the usual P2O5 because it is nonhygroscopic and yields temperature-controlled surface concentrations together with excellent final surfaces. Surface doping nearly as high as that produced by phosphorus pentoxide has been observed for sources at 850" to 900°C. Reproducible high sheet resistances were obtained by using slow flow rates (1 linear in. per min) and staggered-baffle gas mixing with the nitride at 550°C. Both inert gas (argon, nitrogen) and oxidizing ambients have been examined. Oxygen reacts to produce anhydrous P2O5, consuming the source at a rapid rate. Nitrogen, except for short diffusion times, suppressed the dissociation reaction and sometimes produced inferior surfaces. Argon appears to be a more useful ambient. PHOSPHORUS is a common impurity atom which may be introduced into a semiconductor lattice to create a p-n junction or an nn contact region. Various investigators1-4 have described techniques which can be used with either elemental phosphorus or certain of its compounds. This paper discusses a newly available compound of phosphorus, phos- some processes silicon wafers are precoated with a phosphate glass which acts as the doping source. Although a nonoxidizing form like elemental phosphorus or a phosphine can be used, most diffusion methods usually involve the use of phosphorus pentoxide. Because of the rapid volatility of this compound, a two-step process is often used, combining a gaseous deposition to introduce a predetermined quantity of phosphorus into the silicon with a later redistribution to obtain the desired distribution and surface concentration. Such a process usually involves predepositing phosphorus at surface concentrations greater than 1020 cm-'. At such doping levels the phosphorus-diffusion coefficient appears to be strongly concentration-dependent.596 Distribution profiles5'9 for these high concentrations of phosphorus do not follow Fick's laws, having extended subsurface regions which appear electrically to be nearly uniformly doped with ionized impurity atoms. Radioactive-tracer experiments also show near-surface anomalies in the distribution profile. Additionally, it has been shown1' that the introduction of very high surface concentrations of impurity atoms into silicon (a step necessitated by the subsequent lowering of concentration during the redistribution) creates dislocations, even in material having no dislocations originally. For device fabrication the use of oxide masking introduces certain difficulties and limitations.7'8 The standard practice of using phosphorus pentoxide as an impurity source adds other problems to these because of the speed and ease with which this compound reacts with moisture present in any gas in contact with it. In fact, P2O5 is one of the fastest and most effective drying agents for gases. Because it is such an excellent desiccant, completely anhydrous phosphorus pentoxide is difficult to obtain and is even more difficult to keep dry. Adequately dry gloved boxes must be used for storage and transfer of the chemical. The presence of even traces of moisture will cause formation of phosphoric acids which, during the high-temperature diffusion, results in polyphosphoric acids of variable composition. Such reaction by-products end up as gradually accumulating viscous fluids in the cooler parts of the diffusion furnace. The calculation of the final solute distribution for

Jan 1, 1964

By Kenneth S. Johnson

Iodine, a grayish-black nonmetallic element, with a density of 4.9 g/cm3, is a solid at ordinary temperatures. It is a member of the halogen family, along with fluorine, chlorine, bromine, and astatine. Iodine melts at 114°C. and at 184°C it is volatilized to a blue-violet gas that has an irritating odor. It does not occur as an element in nature, but occurs as iodates, iodides, or other combined forms. It is the 47th most abundant element in the earth's crust. Iodine was discovered by Bernard Courtois in 1811. He observed an unknown substance in the crude soda ash that results from the burning of seaweed. Samples of this unknown substance were identified to be a new element, and in 1813 Gay-Lussac named the substance iode, from the Greek word for violet color. The world production during 1989 and 1990 [(Table 1)] is estimated to be about 16 million kg per year (Lyday, 1991), of which about 30% is consumed in the United States. GEOLOGY AND MINERALOGY Compounds of iodine are minor constituents in seawater and brines, in certain marine organisms, and in minerals of the Chilean nitrate deposits. Seawater contains approximately 0.05 ppm iodine, and certain marine organisms, such as seaweed, sponges, fish, and some brown algae, are able to further concentrate iodine (Lyday, 1989a). Some seaweed can extract and accumulate iodine up to 0.45% of their weight, on a dry basis. The northern Chilean nitrate deposits, in the Atacama Desert, contain the following iodine minerals: lautarite, Ca(I03), (calcium iodate); dietzeite, CaJIO,), (CrO,) (calcium iodate-chromate); and bruggenite, Ca(I03), . H20 (Erickson, 1981). Various subsurface brines also contain iodine compounds. Some gas-field brines in the United States and Japan locally contain 30 to 1 300 ppm iodine. Several coals in Germany also contain iodine compounds. Iodine has been recovered from brines mainly in Japan and the United States, but also in Java, Indonesia, Italy, England, and the former USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. Seaweed was a major source of iodine for the world in the first half of this century, and it remains as a large resource. The reserves and future resources of iodine are large, even excluding the resources in seaweed and seawater, and are shown in [Table 1]. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable. PRINCIPAL PRODUCING COUNTRIES Major iodine-producing nations are Japan, Chile, the USSR, and the United States, with lesser amounts being produced in China and Indonesia ([Fig. 1; Table 1]). Annual world production in 1989 and 1990, respectively, is estimated at 15.6 and 16 million kg. In Japan and Chile, the production of iodine depends on production of other materials, such as natural gas or nitrates, respectively, whereas in US operations (in Oklahoma) iodine is the major product recovered from natural brines. Chile was for a long time the principal world producer of iodine from its nitrate-fertilizer operations, but in recent years Japan has become the world leader with increased production of natural gas and associated iodine-rich brines.

Jan 1, 1994

By Henry A. Stiff, and Lawrence E. Davis

The authors previously presented a method for predicting the tendency of oil field waters to deposit calcium sulfate. The present paper gives a similar method for calcium carbonate. Methods for predicting calcium carbonate scaling tendencies in fresh waters have been available for some time, but these could not be used for brines. By experimentally deriving the value of the K term in the Langelier equation, a method has been developed which applies to waters of high salt content. A statistical study is included which shows that the experimentally derived values of K are in good agreement with actual conditions. Several applications of the final equation to production practice are given. INTRODUCTION The authors previously presented a method for predicting the formation of calcium sulfate scale in oil field waters.' Although calcium sulfate deposition is important in production operations, the majority of scale problems involve calcium carbonate. The present communication discusses a method by which the formation of this type of scale in oil field waters can be predicted. Calcium carbonate precipitation is caused by a shift toward carbonate in the carbonate-bicarbonate-carbon dioxide equilibrium. When equilibrium shifts in the other direction, the precipitate goes back into solution. Since there is usually considerable delay between the establishment of an equilibrium and the precipitation or solution of calcium carbonate, unstable conditions exist in which a water will precipitate or dissolve calcium carbonate on standing. Tillmans? who did a major part of the early work on carbonate scaling, pointed out that the condition of equilibrium not only indicates the tendency of a water to scale but also is an indication of its corrosive properties. Previously precipitated calcium carbonate combines with iron to form a dense crust which inhibits corrosion. If the water tends to dissolve carbonate, the scale becomes porous, and electrolytic corrosion takes place. Tillmans1 work was extended by several investigators until in 1934 Langeliers developed an equation setting forth the conditions of carbonate equilibrium. By the use of this equation the pH of a water at equilibrium can be calculated. If the actual pH is higher than the calculated pH, the water has a tendency to form scale. If it is lower. the water has a tendency to be corrosive. Langelier's equation can be expressed in a simple form as follows: SI = pH-pCa-pA lk-K where: SI is the stability index. A positive index indicates scale formation. A negative index indicates corrosion. pH is the pH of the water sample, as actually determined. pCa is the negative logarithm of the calcium concentration. pAlk is the negative logarithm of the total alkalinity. K is a constant, the value of which depends on the total salt concentration and the temperature. This equation has been shown to apply to waters with totaI solid concentrations as high as 4.000 ppm. In fact, control of fresh water treatment by means of this equation has been standard text-book practice for a number of years. Nomographs have been worked out so that the stability index of a fresh water sample can be determined in a matter of minutes. Most oil field waters, however, contain well over 4,000 ppm of salts and for this reason the usual application of Langelier's equation can not be made. By an empirical method we have extended the application of the Langelier equation to waters of high salt concentration. By the use of this equation the tendency of oil field waters to deposit calcium carbonate can be predicted.

Jan 1, 1952

Surface mining of coal involves removing soil and rock that overlay coal beds in order to expose the coal. Compared to underground coal mining, surface mining generally costs less, is safer for miners, and usually results in more complete recovery of the coal. However, it also results in much more extensive, though temporary, disturbance of the land surface, which can cause serious environmental problems unless the mined land is carefully reclaimed. The earliest commercial U.S. coal production was in the anthracite region of Pennsylvania. Beginning in 1807, mining became important enough for the federal government to begin keeping statistics on annual production. During those early years of coal mining, reclamation of mine sites and Support facilities was not required by law; however, in the 1930's, as surface mining became more widespread, the idea of mandatory environmental protection and reclamation started to grow. In 1939 West Virginia enacted the first law to regulate the coal mining industry. Similar laws were enacted by Indiana in 1941, Illinois in 1943, and Pennsylvania in 1945. During that period, coal production accelerated greatly and the surface mining of coal became much more prevalent. During World War 11, the demand for coal took priority over environmental concerns, with little consideration for reclaiming the land after mining. Mining pits were not backfilled. Dangerous highwalls were left exposed. Trees and other vegetation were buried by waste material that was simply dumped down the slopes below mines. Topsoil was buried or allowed to wash away. Landslides formed on unstable hillsides. Slopes eroded rapidly because of the lack of vegetation. Polluted water collected in mine pits. Streams became clogged with sediment. Streams and rivers were frequently polluted by acid mine drainage. This vivid image of surface coal mining remains indelible in the minds of most Americans, who remain unfamiliar with modem surface coal mining methods and the changes brought about by the Surface Mining Control and Reclamation Act. After 1945, more coal-producing states instituted regulatory pro- grams. Many required permits for mining. Some included inspections. A few made operators post performance bonds to guarantee reclamation when mining was completed. However, due to the variations in those individual programs, it cost less to produce coal in states with less stringent reclamation requirements, giving operators in those states an economic advantage, generally at the expense of environmental quality. With the 1970's came a surge in the demand for coal resulting from the nation's need for increasing electric power generation and the uncertain supply and increased cost of imported petroleum-based fuels. The resulting increased coal production prompted a series of state laws, primarily in the West, aimed at controlling the environ- mental effects of surface mining. During the late 1960's and early 1970's, North Dakota, Wyoming, Colorado, and Montana passed laws to regulate mining and reclamation. The continuing lack of uniformity among the state surface mining programs and the increase in unreclaimed land and associated pollution of water and other resources caused a growing demand for nationwide regulation of surface coal mining, both to remove the economic inequities and to is sure an acceptable standard of reclamation. After many years of debate, Congress passed the Surface Mining Control and Reclamation Act (SMCRA), which was signed into law August 3, 1977. The Act established a coordinated effort between the states and the federal government to prevent the abuses that had characterized surface coal mining in the past. The law also applied to surface disturbances created by underground coal mining.

Jan 1, 1992

By O. E. Palasvirta

Close examination of most so-called n.eu processes in mineral dressing reveals that they were conceived and developed a long time ago. High-intensity magnetic separation is no exception. Although its application in iron ore beneficiation seems new, in Germany the process has been commercially successful for almost two decades. High-intensity separators have long been standard equipment in the glass sand industry; they have also been used in concentrating some of the more unusual para-magnetic minerals. The basic features of an induced-rotor, high-intensity magnetic separator were described by Desire Korda in Paris in 1905,' and many patents have since been issued for improvements on the original design. Fig. 1 shows the basic design of an induced-rotor separator. Several U. S. manufacturers have been supplying induced-rotor separators for many years, but these are all devices of relatively low capacity, not suitable for treating such low-cost commodities as iron ore. On the other hand, two German manufacturers are offering induced-rotor separators of high capacity, both proven in the field. The present investigation was prompted by the apparent success of the German installations and by the discovery of iron ores on this continent which may be amenable to high-intensity separation. The objective was to gain better insight into the underlying principles of separation in a high-intensity field and to use this knowledge in selecting or designing an optimum separator. THEORETICAL CONSIDERATIONS he well known low-intensity magnetic separators are. without exception, of the the magnet type with more or less similar field shapes. It is therefore permissible to speak of their comparative strengths in terms of field intensity alone. However, proper understanding of the high-intensity magnetic separation process requires somewhat deeper analysis of the relationship between the magnetic field and the attractive force. Contrary to a widely held belief, a magnetic field of parallel lines of flux exerts no attractive force on a magnetically susceptible particle, but merely aligns its poles parallel to the lines of flux. On the other hand, a non-uniform field attracts a magnetically susceptible particle in the direction of the converging lines of flux. Thus the force of magnetic attraction varies as the product of the field intensity and the field gradient: dH ds As the induced-rotor magnetic separator is primarily intended for separating feebly magnetic materials, it is important that maximum attraction be attained. For the designer, then, the relationship between the magnetic field and the attractive force has the following implications: 1) Insofar as possible, the separation gap must be saturated with flux. 2) The rotor surface must be shaped to insure maximum convergence of lines of flux toward the rotor. 3) The primary pole face (opposite the rotor, on the other side of the separation gap) must be shaped so that the lines of flux do not diverge from it at any location in the effective separation zone. The actual attractive force of the rotor, and its critical speed, can be calculated as shown by Runo-linna, provided that the true flux density, the field gradient, and the magnetic susceptibility of the mineral can be measured with sufficient accuracy. The irregular shape of the rotor surface makes flux measurements difficult, but it can be done if a suitable gaussmeter is available (see Fig. 2). Calculations by the author, and comparisons with the centrifugal force exerted by the rotor, indicate that the force pinning a hematite particle to the rotor is of the same order of magnitude as the force holding a

Jan 1, 1960

By H. J. Beach

This paper describes the properties and uses of cementitious mixtures containing 10 to 20 per cent bentonite and 2 per cent or more sodium chloride. Salt additions improve bentonite cement by increasing early strength and stabilizing viscosity without changing thickening time. The volume yield of cement is increased 20 per cent or more without lowered early strength. The unique properties of salt in this type of system make savings of more than 10 per cent possible where light-weight, low-strength cementitious material is adequate to fill behind pipe. The density range of these mixtures is 12 to 13 1b/gal and the filtration rates are medium-low, aiding the placement of long columns in primary cementing. Where available, sea water is an ideal salt source in preparing these slurries. INTRODUCTION Accelerators increase the rate of cement hydration. In speeding reaction with water, they can affect cement performance by reducing thickening time and increasing early strength after set. Accelerators that cause both effects can be considered "total", and those which produce only one effect can be called "partial". Materials that act conversely to accelerators are retarders. and they also can be total or partial. Partial retarders. make high-temperature cementing possible by prolonging thickening time while impairing early strength only slightly. Most known accelerators are total. A useful partial accelerator would increase strength without altering thickening time. This report concerns material combinations in which a normally total accelerator exerts unique partial properties. Utilizing these limited effects improves bentonite cement. SEPARATE EFFECTS OF SODIUM CHLORIDE AND BENTONITE ON CEMENT Sodium chloride and calcium chloride are commonly used in cement, and at low concentrations their effects are similar. Ludwig1 studied sodium chloride in API Class A and Class E cements.' Figs. 1 and 2 sum- marize his data taken at 140°F on slurry pumpability and early strength. Normal water-to-cement ratios are 0.46 and 0.40, respectively, for Class A and Class E cements. At saturation the salt content is 12 to 14 per cent of the weight of cement solids. The illustrations, therefore, cover the range of salt solubility in the mixing water. The data show that sodium chloride is a total accelerator of the Class E cement studied over the range of solubility. It is total in Class A cement to 6 per cent. Above this concentration salt becomes a retarder— partial from 6 to 10 per cent and total above. These results are general for different brands of Class A cement, although the shift from acceleration to retardation may occur at different salt concentrations for different temperatures. The results are specific for the Class E brand studied. In discussing his data, the investigator emphasized that different Class E cements might respond erratically to salt, depending on the brand chosen. Morgan and Dumbauld3 escribe the properties of bentonite cement in a paper that is a standard reference in using these systems. Bentonite functions in cement as an enabling agent; each bentonite addition equal to 1 per cent of the weight of dry cement makes possible the further addition of 4.5 per cent water.' Thus, 10 per cent bentonite in Class A cement, normally slurried neat with 46 per cent water, enables the slurry to contain another 45 per cent before settling. Water is one of the lightest and cheapest cement extenders; it reduces density and cost. Bentonite cements produce uniform slurries having low susceptibility to solids separation. After set, they offer low resistance to perforation.

By Stanley L. Lopata, Eric B. Kula

The problem of preferred orientation has been considered in quantitative phase analysis by X-ray diffraction techniques. The average intensity of a diffraction peak can be obtained by integration over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. For rod or wire, where the pole figure shows rotational symmetry, the intensity is measured along a radius of the pole figure. Where no symmetry is present, rotational symmetry is imparted by rapid rotation of the sheet around its surface normal during measurement. These methods are applied to the determination of aus-tenite in an Fe-31 pct Ni rod and Fe-28 pct Ni sheet. X-RAY diffraction techniques are frequently used for quantitatively determining the relative amounts of two or more phases present in a structure.1,2 Briefly, the method requires a measurement of the intensity of a Bragg reflection for each phase. The method is based on the principle that the intensity of a Bragg reflection, IA, is directly proportional to the volume fraction of the given phase present, CA: T KRACA/2µ [1] where K is a constant independent of the diffracting phase, RA can be calculated and depends on the Bragg angle ? and the particular reflection measured, and µ is the linear absorption coefficient of the mixture.' For a mixture of two phases A and B, IA = RAcA [2] IA/IB=RAcA/Rbcb and CA+ CB = 1 [3] This allows the volume fraction of a phase to be calculated directly from the measured integrated intensities of the two phases present. This method is frequently used for quantitatively determining retained austenite in steels, but can be used for the quantitative determination of in titanium alloys, as well as phases in other alloy systems. The intensities are generally measured by diffracting only from planes whose normals are perpendicular to the specimen surface, with the implicit assumption being made that this intensity is typical of reflections from planes whose normals lie at other angles to the surface. If the specimen contains a texture or preferred orientation of the crys- tallographic planes by virtue of previous mechanical working, however, this measured intensity is correct only if the intensity level fortuitously is one times random. Examination of pole figures for actual rolled sheet shows that the intensity level at the center of the figure is seldom at the random level, and can very easily differ by a factor of five or more, leading to a commensurate error in the calculated amount of the phases. Textures have been commonly found in materials which are cold-rolled or recrystallized after cold rolling. This problem is becoming of greater importance since structural materials in use today, such as the high-strength stainless steels, frequently are further strengthened by cold rolling, and hence contain textures. Although high-strength carbon-containing alloy steels generally do not contain textures, some of the newer thermomechani-cal treatments will impart a texture even in these cases. In the case of hexagonal metals, such as titanium, probably every wrought sample will show some anisotropy. Since the standard X-ray techniques are inapplicable in all these cases, there is a clear need for some method of taking this anisotropy into account. The specific problem is to obtain the integrated intensity of a Bragg reflection for each phase, averaged over all orientations of the sample with respect to the X-ray beam. This can be done either by purely mechanical means or by a mathematical averaging. Mechanically, a small spherical speci-

Jan 1, 1965

By Guy Borden, Michael J. Rzasa

Laboratory data on bubble point pressures and reservoir volume factors have been correlated as functions of solution gas-oil ratio, calculated gas gravity of the pentanes-and-lighter fraction of the entire fluid, differential residual oil gravity, and reservoir temperatures. INTRODUCTION Several correlations of crude oil properties have appeared in the literature. D. L. Katz4 in 1942 presented five methods of predicting oil shrinkage. these being of decreasing accuracy for decreasing amounts of information available. M. B. Standing- in 1947 published three correlations of laboratory flash vaporization data of California crudes. From values of GOR (gas-oil ratio), gas gravity, liquid gravity, and temperature, his correlations will predict bubble point pressure, formation volumes of bubble point liquids, and two-phase formation volumes. Curtis and Brinkley2 in 1949 presented several correlations. From the gas-oil ratio, an approximation of reservoir volume factor and barrels of condensate recoverable per barrel of reservoir space may be obtained; along with liquid gravity and reservoir temperature, the GOR will allow prediction of bubble point pressure. These last cor- relations seem to be more qualitative than quantitative. Generally, laboratory bottom hole sample tests furnish information on solution gas-oil ratios, residual oil gravities. bubble point pressures, viscosities of oils, liquid shrinkages, and occasionally gas gravities. Each of these data has its own applications and use in reservoir engineering calculations. The particular uses of correlated bottom hole sample data are found in (1 Providing a basis for obtaining estimates of formation crude properties in fields where bottom hole sampling is impractical or impossible. (2) Greatly reducing the time in obtaining the desired information. (3) Determining the applicability of the results from various bottom hole samples to particular field problems. (4) Avoiding, in many cases, the uncertainties of sampling by replacing it with an element over which greater control can be exercised. (5) Permitting use of preliminary field data in application of production procedures before a bottom hole sample can be obtained and analyzed in the laboratory. (6) Serving as a check on data which may appear out of line. (7) Estimating for a particular type crude the appropriate equilibrium constants by working backward from the bubble point pressure. (8) Estimating original or other past history properties of reservoirs that were not sampled in the past. PROCEDURE Application of the published correlations4,6 to Stanolind laboratory data indicated that the general scheme presented by Standing" could give dedrable results if changes were made in parameter positions and scales. The correlation curves were drawn with all the variables having consistent gradations except the temperature increments which were drawn in to best fit the data. The variables from available Stanolind laboratory data are defined below: (1) Gas-oil Ratio: Gas is liberated at reservoir temperature by differential vaporization (or rather by a series of flashes, approaching differential vaporization) and measured at atmospheric pressure and temperature, at which the compressibility factor is assumed to be unity. The oil is the residual liquid remaining after the pressure has been reduced to atmospheric. For the gas-oil ratio both volumes are corrected to standard conditions of 14.7 psia and 60°F. (2) Gas Gravity: It was decided to arbitrarily divide the hydrocarbons of the entire bottom hole sample into pentanes-and-lighter and hex-anes-and-heavier, and use a calculated gas gravity of the pentanes-and-lighter for a correlating variable. (Sample calculation is shown in Table 111.) (3) Liquid Gravity: This is the API gravity of the residual liquid from the differential vaporization. The gravity is measured at room temperature and corrected to 60°F.

Jan 1, 1950

By H. Von Michaelis

The world is rapidly becoming more ?green? i.e. energy conscious. Since mining and mineral processing are massive energy users, the mining industry is seeking ways to reduce its energy footprint. In mining and mineral processing operations, energy is often the most expensive cost item. Comminution, i.e. grinding, is frequently the most energy-intensive step between mine and metal. High pressure grinding rolls (HPGR) are being installed in a rapidly growing number of ?hard rock? mineral processing operations. In the energy conscious cement industry, HPGR grinding has been standard practice for decades. HPGR is known to be energy-efficient; the question is how energy efficient? How can the energy efficiency of HPGR be enhanced? This paper reviews recent HPGR applications for the processing particularly of copper, gold, platinum, PGM-Ni-Cu and iron ores. HPGR technology is discussed with respect to energy efficiency. The harder the ore the greater the energy savings are likely to be. Typical energy savings of 10?20% can be expected when installing HPGR vs. a SAG mill. Wipf(2005) showed why conventional Bond Work index tests on HPGR product is likely to under-estimate the energy savings that can be achieved by installing HPGR. Energy efficiency of HPGR is, however, ore-specific. The biggest energy savings of HPGR tested thus far is 9.5 kWh/tonne claimed for Vista Gold?s Mt. Todd gold ore from Western Australia, a savings of over one-third of conventional SABC comminution energy. Several commercial scale iron-ore pellet feed plants install HPGR for fine-grinding of concentrate to increase the surface area of pellet feed in a manner that reduces overall energy consumption. Energy-consumption in comminution is, however, only part of the energy savings benefit story. HPGR typically also reduces the amount of steel lost through wear of mill liners and media. Marsden(2008) showed that when the energy that would have been consumed to produce the steel that is saved by applying HPGR is factored in, then the overall energy savings of HPGR is considerably greater. Johnson et al.(1988, 2005) tested HPGR in a flowsheet in which energy savings of around 50% can be expected if HPGR product screen oversize is recirculated to the HPGR. Innovative flowsheets have been proposed by Rule et al.(2008) and by Morley (2008) which are expected to result in significantly increased energy savings. HPGR applied in flowsheets in conjunction with coarse ore separation devices, e.g. ore sorting or DMS to remove barren waste from HPGR feed promises significantly greater energy efficiencies. Fine-grinding and ultra-fine grinding of ore or concentrates in conventional ball mills results in energy consumptions that increase exponentially with product fineness. Wipf (2009) presented a flowsheet in which he proposed the installation of HPGR ahead of the Aerosion ?Disintegrator? for ultra-fine grinding of ores and/or concentrates. This dry grinding arrangement is expected to achieve ap80 = 7 µm using up to 100 kWh/t less energy than could be achieved by wet ball milling. Using conventional comminution, an ore might require grinding to p80 = 45µm (? 325 mesh), for example, to liberate the valuable components, e.g. magnetite, from gangue, e.g. silica. Inter-particle comminution in HPGR may break some ores along grain boundaries thereby liberating valuable minerals from gangue at a much coarser particle sizes. Early magnetic separation rejection of silica gangue liberated from magnetite by HPGR at coarser grain sizes could further reduce downstream comminution energy consumption.

Jan 1, 2009

By M. H. Pilkuhn, H. Rupprecht

p layers on n-type substrates of GaAs were prepared by difhsion of zinc into these substrates. Experimental details about the diffusion technique will be presented. It will be shown that inhomogeneity in the substrate doping level and crystal shucture defects cause nonplanarity in the junction plane. These nonplanarities give rise to high threshold current densities. From incremental sheet-conductivity measurements the zinc profile is derived. Data about surface concentration and gradient of the zinc concentration at the junction are presented. Finally, some results of laser diodes, which were made of wafers with extremely planar diffusion fronts, are discussed. ThE investigations reported here are part of a program concerned with the materials aspect in the fabrication of GaAs laser diodes. This includes studies of the influence of crystal defects introduced both during the growth of the crystal and as a consequence of subsequent diffusion. Compared with the progress made in the investigation of structure defects, for instance by X-ray microscopy in materials like silicon, no similar results are known so far for the case of GaAs. The further progress in laser diodes will depend very much upon our knowledge of these structure defects and subsequently upon our ability to avoid them. Laser diodes of GaAs had been made mostly by diffusing an acceptor impurity, normally zinc, into an n-type substrate. This procedure was found more convenient than the inverse one for various technical reasons. We will follow this line and restrict ourselves to zinc diffusion only in this paper. DIFFUSION TECHNIQUES AND EXPERIMENTAL DETAIL In order to set a refgrence for our experiments, we used a standard procedure for the diffusion runs. The diffusions were carried out in a sealed quartz tube for 2-1/2 hr at 850°C. One milligram zinc arsenide (ZnAsz) per cu cm of the tube volume served as zinc source. Under these conditions the junction depth was between 25 and 30 p. It is assumed, according to the investigations of the zinc arsenide system by V. Lyons and V. ilvestri,' that ZnAs2 dissociates completely at 850°C into ZnsAsz and Asg. Since there is a condensed phase of ZnsAs2 in the tube at 850°C, the partial pressure of zinc is controlled by the pressure of the arsenic formed by the dissociation of ZnAs2. Due to the fact that the zinc partial pressure resulting from the dissociation of ZnsAsz is only a weak function of the partial pressure of arsenic, the amount of the initial ZnAs2 is not very critical. Experimentally, we found that the junction depth, as well as the surface concentration, was practically the same, if the ingots of ZnAs2 varied between 0.2 and 5.0 mg per cu cm. The wafers were oriented with the main faces in (100). Surface damage due to cutting and lapping was removed by a chemical-etch treatment in a rotating beaker (etch solution: HzSOr, H202, and HzO in a ratio 3:l:l). The GaAs substrate material was n type and doped with tellurium, selenium, silicon, or germanium. It was grown by means of horizontal or Czochralski techniques. After the diffusion process, junction depth and planarity were checked either by grooving with a

Jan 1, 1964

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum were grown by multipass zone melting in an electron beam apparatus. Tension tests of these crystals at 4.2 x 10&apos;* per sec-gave a resolved louler yield stress of 7300 psi at with a chisel edge; total uniform deformation increased from 1 to 2 pct at 77°K to over 20 pct at 300°K. This, and slip traces, indicated that deformation is more inhomogeneous at lower temperatures. Deformation occurred exclusively by slip in <III> directions, on planes in the <111> zones. Cross slip was frequent, particularly for those orientations where the resolved shear stress on the cross system was comparable with that on the primary plane. The existence and magnitude of the upper yield point were found to be sensitive to orientation. This effect was related to the circumvention of dislocations which were "locked" by interstitial atoms, by double cross slip, or composite slip, of screw dislocations. Prestrainirg at 300°K did not remove the upper yield point in subsequent tension at 77°K. Also, this treatment was found to cause yield points, where none existed for the unprestrained material. This behavior was also rationalized in terms of the circumvention mechanism. The mechanical properties of polycrystalline tantalum have been investigated by several workers,1"4 and may be summarized by pointing out the following features: a) Sharp rise of yield stress with decreasing temperature below room temperature. b) Response to strain aging at 300" to 400"C. c) Yielding with upper and lower yield-point phenomenon at and below room temperature. d) Low strain hardening below room temperature. e) Reluctance to twin except at very high strain rate. Furthermore, tantalum is ductile at ordinary strain rates as low as 4.2"K.&apos; This feature, in particular, makes tantalum unique among the high melting point, bee transition metals of Groups V and VI in the periodic system. Therefore, a more fundamental and detailed knowledge of the low-tempera- ture deformation of tantalum is required. Since high purity and the absence of grain boundary effects make such a study most productive and unambiguous, the method of electron beam zone melting was selected for the preparation of test specimens. This technique has the further advantage that crystals may be seeded in order to obtain any desired orientation. EXPERIMENTAL The electron beam zone-melting equipment was constructed as a modification of that described by Calverley, Davis, and Lever? All crystals were made by three passes of the molten zone at 4 mm per min to achieve an optimum purity commensurate with economy of time and material. Table I reports the chemical analyses of the starting and refined metal. It will be noted that there remain some 50 to 70 wt ppm of interstitial elements, while all substi-tutional elements have been removed by evaporation. Tungsten is picked up by evaporation of the cathode filament wire. Crystal seeding was normally successful within 3 deg, and the orientation of all crystals are given in the standard stereographic triangle in Fig. 1. Tensile bars were prepared from the crystals by centerless grinding to the shape in Fig. 2. Specimens were then electropolished to remove 10 pct of the diameter in order to remove worked material and to prepare a metallographic surface for subsequent deformation trace observations. All specimens were held in the split bushing grips as indicated in the cross section view of Fig. 2. All tests were made at a strain rate of 2 112 pct per min in an Instron testing machine.

Jan 1, 1962

By B. R. Banerjee

MATERIAL used throughout this investigation was high-purity aluminum (99.998 pct). The 1/2-in. cubes were cut out of a cold-rolled slab and annealed at 550°C for 1 hr before deformation. The single crystal specimen was 1 in. in diam x 0.33 in. thick, cut from a cylindrical crystal produced by cooling at about 55°C per hr in a furnace which had a convenient gradient of about 10°C in every 4.5 in. vertical crucible length. Specific data on the ten specimens studied are summarized in table I. Three types of deformation were employed: (I) compression in a hand-operated hydraulic press; (2) impact with a 7-lb sledge hammer; and (3) rolling, using a wedge-shaped specimen&apos; to obtain a gradient of deformations varying from 0 to 50 pct along the length of the wedge. Specimens were either deformed at room temperature, or first cooled in a freezing mixture of dry ice and ether at a temperature of —72°C and then deformed between steel blocks cooled with dry ice. The specimens deformed at the low temperature were ground and polished through 000 emery paper and wheels impregnated with alundum and alumina No. 1. During this entire procedure the specimens were dipped frequently in the freezing mixture of dry ice and ether in order to maintain constantly a frosty surface as insurance against overheating. All specimens were given a final electrolytic polish, using two different electrolytes* to insure that the surface effects observed were not char- acteristic of the polishing technique. With both electrolytes, the annealed specimens gave even surfaces with good polish. Several standard etchants were tried without success. The best results were obtained with an immersion etchant, developed in this connection, containing: hydrofluoric acid, 4 parts; nitric acid, 1 part; glycerine, 3 parts. Discussion of Results Typical strain markings have been observed within deformation bands, as shown in figs. 1, 2, and 4. By stereographic plotting of metallographic measurements, the strain markings within a deformation band in a single crystal of aluminum deformed by compression were found to be traces of (111) planes within a maximum scatter of 6". The edges of the deformation band were found to be traces of the (100) planes also within the maximum scatter of 6" (in agreement with previous workers). At 30 pct deformation, this scatter was considered quite normal because of the fragmentation and rotation of the crystal. This solution, based on the traces on one plane of observation is not unique, but as the planes were observed to be those normally and logically to be expected, further work in this regard was not felt to be necessary. The study of strain markings in a wedge-shaped specimen, rolled to obtain a gradient of deformation from 0 to 50 pct, revealed prominent strain markings at 25 pct reduction in thickness (fig.5). Faint and weak strain markings were visually observable up to a minimum reduction in thickness of about 12 pct. Since strain markings have been observed in other face-centered cubic metals after much smaller deformations;1, 2 and since the rate of recovery in aluminum is high, it is believed that, at lower deformations, self-recovery removes the localized strains at the slip interfaces, thus removing the source of the etching effects that give rise to strain markings. At high magnifications, strain markings sometimes seem to appear as very thin, light-banded re-gions bounded by a pair of dark edges. This so-

Jan 1, 1951

By B. J. Arnold

Froth removal rate is perhaps the most important parameter in scaling up from laboratory tests to plant froth flotation circuits. The WEMCO froth factor, the percentage of the froth height over the lip of the cell, accounts for the difference between laboratory and plant froth removal rates. As laboratory tests are generally run with a high pulp level, laboratory results are directly comparable to plant results only when a high froth factor (high pulp level) is run in the plant. When a plant does not have a high pulp level, laboratory results must be modified by using a ratio between laboratory and plant kinetics to predict plant results. This ratio, which accounts for the froth factor is important in testing any new reagents or reagent dosage levels. CQ Inc. researchers have used predictive scale-up equations using this froth factor coupled with equations for kinetics and the residence time distribution in the froth flotation cells. These equations show that modifying the froth factor in the plant can have a large impact on flotation cell yield and reagent use. EQUATIONS DESCRIBING FROTH FLOTATION Scaling up from laboratory- to plant-scale coal froth flotation has been the subject of much research and debate over the years. Determining the proper rate equation to describe flotation kinetics and an equation to describe the residence time distribution in a bank of flotation cells have been particular areas of study. As shown in Tables 1 and 2, various rate equations and residence time distribution equations have been proposed in the literature. These equations consist of one or two parameters giving the rate constant(s) in units of time-1 and a parameter for recovery at infinite time, [Roo]. Dowling, Klimpel, and Aplan (1985) evaluated the rate equations in Table 1 for their ability to fit froth flotation kinetic data and found that all of the equations give reasonably low standard errors. Several of these equations, however, proved to have superior confidence limits for the parameters. Other equations have also been proposed to describe the recovery versus time profile. Most recently, Diao et al. (1992) proposed a first-order form with a sine wave distribution. As indicated in Table 2, investigators have suggested many equations to describe the residence time distribution in continuous froth flotation. To measure the water residence time distribution in a bank of cells, a soluble tracer is often used, with the level of tracer being measured over time at the tailings discharge. This response is then put on a dimensionless basis as described by Austin et al. (1984) in order to compare mixing behavior between cells or under different conditions. Coal flotation cells are generally of the flow-through or hog-trough variety allowing for some degree of backmixing and short-circuiting. While the water residence time distribution (see Figure 1) at the end of one cell in a bank of 1.4 cu ft WEMCO froth flotation cells may approximate perfect mixing conditions (Arnold, 1989), the water residence time distribution at the end of a bank of cells does not. Figure 2 shows the RTD for various flotation cell types compared to that for perfect mixers in series. To better describe the water residence time distribution in coal froth flotation cells, Van Orden (1986) used an equation similar to the perfect-mixers-in-aeries equation. This

Jan 1, 1993

By R. L. Smith, I. G. Greenfield

The binary system Ga-Sb has been investigated by thermal, X-ray, and metallo-graphic methods. &apos;The intermetallic compound GaSb melts at 705.9OC and forms a eutectic with antimony at 11.8 atomic pct Ga. This eutectic melts at 589.8OC. A eutectic appears to be formed at 29.8°C but is too close to the composition of pure gallium to be detected. IN the course of an investigation of the semiconducting properties of the intermetallic compound, GaSb, the phase equilibrium between gallium and antimony has been investigated. Recently, the phase diagram of similar systems, such as In-Sb,&apos; In-AS,&apos; and Bi-As3 have been determined. These diagrams have the same general appearance in that an intermetallic compound is formed at 50 atomic pct and a eutectic is formed on both sides of the intermetallic compound. Jenny,& who has been investigating the semiconducting properties of intermetallic compounds, has concluded from thermal data of several alloys that the phase diagram of the Ga-Sb system resembles those mentioned previously. This paper represents a more detailed study of the Ga-Sb equilibrium. Experimental Procedure The gallium that was used to prepare the alloys was obtained from A. D. Mackay Inc. and the Aluminum Co. of America; the latter reported the purity as 99.95 pct. The antimony was obtained from Bradley Mining Corp. who specified a purity of 99.997 pct. Since the intermetallic compound of GaSb was prepared primarily to be used for further studies of the semiconducting properties, additional purification by a standard zone-melting technique under an atmosphere of hydrogen was performed. Hall-effect measurements on this material indicated an impurity content of less than 3 ppm.5 The antimony also was purified by zone melting and used in conjunction with the compound GaSb to make the necessary alloys for the determinations of the antimony-rich side of the phase diagram. The antimony-rich alloys were chill cast in Vycor tubes which were evacuated to a pressure of less than one micron. Since these alloys expand on freezing, precautions were taken to prevent oxidation of the ingot in the event the tube fractured. To insure homogeneity, the brittle alloys were ground and then placed in the furnace for the thermal-arrest determinations. Since the cost of gallium is high, the experimental procedure was complicated somewhat because of the necessarily limited sizes of the melts. In order to economize, the gallium-rich side of the diagram was determined by using a 35 g ingot of pure gallium initially and adding increasing amounts of antimony in order to obtain additional alloys. The furnace used in the determination of the cooling curves is illustrated in Fig. 1. A 2¼ in. quartz tube, sealed at one end, was fitted with a brass flange which was attached with DeKhotinsky cement. The brass collar was water cooled to prevent the cement from softening. An "0" ring was used to provide a seal between the brass collar and the furnace cover. Nichrome ribbon was wound around a 2 ½ in. asbestos-covered copper core which was used to reduce the thermal gradient in the furnace. The insulation consisted of alternate layers of asbestos and aluminum foil surrounded by sil-o-cel refractory and

Jan 1, 1956

By E. N. Cameron

GRAPHITE has been included in U. S. lists of strategic minerals since the problem of mineral deficiencies was revealed during World War I. Since 1918 the domestic graphite industry has led a precarious existence, and there has been much uncertainty as to the amounts of usable graphite of various grades that would be available from domestic sources in time of emergency. In 1950-1951 therefore, the writer, assisted by Paul L. Weis, undertook a review of domestic graphite sources for the U. S. Geological Survey.&apos; The conclusions of this study are presented here, with a discussion of some technologic and politico-economic factors bearing upon the problem. Uses of Graphite: Natural graphite as marketed exhibits a wide range of properties, which determine the uses to which it is put. The most essential uses are in the manufacture of crucibles and related refractory articles, in lubricants and packing materials, and in the manufacture of batteries, foundry facings, pencils, and carbon brushes. Numerous specifications covering the mineral in its various applications must be met by producers and processors of graphite. The problem of supply is therefore not simply one of procuring a sufficient total tonnage, but the more difficult problem of procuring enough of each different grade to meet foreseeable needs. The amount of graphite required by American industry is not large. Ordinarily only a few thousand tons of strategic grades are consumed annually, yet the elimination of this small tonnage would have serious effects in several industries. Strategic Graphite: Since World War I, 60 to 100 pct of the country&apos;s annual supply of graphite has been furnished from imports. At present, natural amorphous graphite for use in pencils and batteries is produced largely from American-owned mines in Mexico. Graphite for foundry facings is obtained from a number of sources. Neither grade is a serious problem. High purity graphite for carbon brushes and for pencil leads, however, is imported, largely from Ceylon, in the form of amorphous lump graphite. Most of the flake graphite used for crucibles and related refractory articles is likewise imported, largely from Madagascar, and much of the lubricant and packing grade graphite used by industry is obtained from the same source. The strateg&apos;ic grades of graphite are therefore amorphous lump of the Ceylon type, crucible flake, and flake suitable for lubricants and packing. Ceylon lump and Madagascar flake have for many years been accepted as standard by domestic consumers of graphite, and various essential manufacturing processes are geared to the use of graphite from these sources. Ceylon graphite as marketed is classified into several grades based on particle size and purity. Processing methods are said to be simple, but the products marketed are carefully graded and are consistent in their characteristics, an important matter to the consumer. Nearly all the graphite produced in Ceylon is from veins. Resources are reported to be large, labor is cheap, production costs are low, and world competition is slight—factors accounting for the commercial success of the graphite mining industry in Ceylon. Madagascar is reported to have deposits of the Ceylon type, but its output consists almost entirely of flake. Madagascar graphite as received in the U. S. is further processed by importing organizations, and a large number of grades are produced to meet industry requirements, especially those for crucible flake and for lubricant and packing grade flake. Madagascar crucible flake as marketed is noted for coarseness, uniformity, toughness, clean-

Jan 1, 1957

By M. L. Jeremic

"Hydraulic mining consists of coal erosion by powerful jet s of water from hydraulic monitors operated by remote control. The broken coal is crushed and mixed with water and then transported from the face to the surface using gravity whenever possible. This is a simple, safe and productive method. It will easily satisfy North American productivity standards if the structural features and coal properties are favourable for water jet cutting technology (Kaiser Resources Ltd. , hydraulic mine). General ConsiderationIn open-pit mines, placer mining (Fig. I) and hydroelectric construction projects, hydraulic earth moving techniques have been successfully applied. The stripping and transporting of the overburden has been accomplished by means of large monitor jets augmented by slurry pumps and pipes. An extension of this technique has led to the underground extraction of coal and ores. To date, the method has been most successfully used in undergrond coal mining, because the coal can be easily cut and flushed away by water jets, and the rocks of the roof strata can be left behind. Due to this favourable situation, the hydraulic mining definition only relates to the underground coal mines.At present, there are four basic types of hydraulic mining, which can be defined according to the coal breaking technique used in each case. The methods are briefly discussed below:(1) Coal excavation may be carried out by conventional techniques, but the mine is designed and equipped for the hydraulic transport of the mineral from the working place to surface. Under these circumstances, the coal breaking may not be influenced by the water jet, however it may be indirectly involved. For example, pre-loosening of the coal may be done by water infusion-hydraulic fracturing. Water may also be used to flush the broken coal, which has been excavated either by drilling and blasting or by mechanical cutting, into the transport flumes. In other cases, a mechanical loader may load the coal directly into the hydraulic transport system, without using any water for the extraction process. This hydraulic mining concept is primarily used for hard and impermeable coal, such as anthracite."

Jan 1, 1980