Search Documents

By D. D. Pollock, D. I. Finch

PREVIOUS work' on a four-component system (Cu-Mn-Ni-Fe) resulted in the development of consistent relationships between the chemical composition and the electrical properties of these manganin-type alloys. The present study was undertaken to develop alloys with temperature coefficients of resistivity and thermoelectric properties more desirable than those of the manganin type, and to determine whether the relationships which had been found for the Cu-Mn-Ni-Fe alloys could be extended to five-and six-component alloy systems. PREPARATION OF ALLOYS The five- and six-component alloys were made from OFHC copper rod, ARMCO iron, electrolytic nickel, manganese cathode chip, and special high-purity aluminum and indium. A Cu-Mg master was used for deoxidation. The compositions of these materials are given in Table I. The alloys were melted and cast as indicated previously,' except that no cover was used and the melts were teemed. EXPERIMENTAL PROCEDURE The finished wire size of 0.0808 in. diam was again selected for the reason that the test specimens would be self-supporting, thus eliminating any extraneous effects which might have been introduced by winding smaller diameter wire on spools or forms. The following tests were performed on the finished wires: A) Chemical Analyses—All of the components of these alloys were determined by premium gravimetric methods. The principle residual impurity contained in these alloys is 0.008 pct Mg (by weight), maximum. Tables II and 111 present the mean analyses computed from at least four determinations of each constituent. B) Electrical Characteristics—The test procedures forthe determination of the thermal emf vs copper, resistivity, and the resistance-temperature relationship are given in detail in Ref. 1. It was also shown that the resistance-temperature relationship is of the form Pt = P,n + At -B/2, [1] where P, is the resistance at t C expressed in percent of a given standard resistance, P, is this per- 0 centage at 0°C, and A and B are constants for a given, properly treated, composition. The results of the electrical tests are also given in Tables II and 111. INTERPRETATION OF DATA The modified Linde2 formula, known to be valid for dilute binary solid solutions, was applied to the complex Cu-Mn-Ni-Fe type alloys. This relationship is of the form where Ap is the increase in resistivity. Zb the valence of the solute, Zn the valence of the solvent, and K and K are designations assigned by Robinson and Dorn3 to the constants for the periodic group to which solute element belongs. The units of K, are -cm per valence difference squared per at. pct; those of K2 are pa-cm per at. pct. For the sake of brevity, these units are not repeated in the following discussion. Calculations were made to determine if this formula was accurate for five-component systems. No experimental studies were made of the Cu-In and Cu-A1 binary systems. The effects of indium additions upon the resistivity of copper are given by Linde. These data, along with those of the effects of Mn and Fe, permitted the calculation of the effects of Al.

Jan 1, 1959

By J. P. Matoney, E. J. Sandy, D. A. Dahlstorm

INTRODUCTION Before an understandable discussion concerning coal-dewatering processes can be initiated, it is necessary to define some terms of usage. The many different meanings and interpretations of terms preclude development of standard definitions so that the terms which are defined in this chapter should be regarded mainly as working terms intended to facilitate communication. A coal slurry ' might be defined as a watery suspension carrying particles of fine coal and other assorted material ranging upward in size from the finest clay particles. Some particles may be in the colloidal sue range and exhibit characteristics of suspended colloids. The dilution of the system generally is such that it is in a condition of independent particle subsidence. In some coal mining areas a slurry is regarded as a suspension of fine coal and other materials having a dilution that cannot be economically dewatered by filtration. A coal slime may be regarded as a slurry containing particles of such size range that 50 per cent or more (by weight) will pass a 200-mesh sieve. Slime suspensions generally are difficult to handle without special treatment in conventional sedimentation equipment. A coal sludge is defined as a slurry that has been partly dewatered by sedimentation usually to a thick or viscous consistency where further dewatering can be most readily facilitated by filtration. Culm and silt are terms characteristic of coal-preparation practice which should be defined. In anthracite terminology, culm is the generally coarse residue or waste accumulation of coal, bone and rock from preparation plants most of which are no longer functional. Culm has a wide range of sizes, some rather coarse, and except to differentiate it from silt, the term is of limited interest in this discussion. In anthracite terminology, silt is the accumulation of waste fine coal, bone and slate settled out from preparation plant water in excavated basins. Silt is generally made up of particles ranging in size from 3/32-in. round-opening screen to the very finest sues. Silt is also referred to at times as sludge, fines, slush, and mud and is the partly dewatered derivative of what has been previously defined as slurry. In the terminology of the bituminous coal producing areas, the word culm commonly corresponds to slurry or slime, depending upon the size distribution of the suspended solids. Editor's Note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections authored by each individual as is the case in most chapters of this book.

Jan 1, 1968

By E. Sabina Brady

Over the next two decades there will be significant trade and development opportunities in China for mining, engineering, equipment, and construction companies interested in becoming part of the development of China's chemical and fertilizer industries. At last count, China's phosphate ore reserves of 11.8 Gt (13 billion st), ranked fourth in the world behind the US, the USSR, and Sahara-Morocco. However, a recent statement by the head of the Ministry of Geology and Minerals, Sun Daguang, claims that with increased prospecting in the last few years, China's phosphate reserves now rank first in the world. Whatever the actual size of its known and potential reserves, China's present phosphate processing capabilities fall far short of demand, while the substantial progress that has been made in this area points out the severity of the problems that still remain. Since 1949 China has developed 181 mines and increased its phosphate concentrate production from 10 kt (11,000 st) to 10.86 Mt (11.97 million st). By the 1980s, China was the third largest chemical fertilizer producer in the world-although this claim is slightly misleading as China's nitrogen/phosphate potassium ratios are far from average world ratios and even further from US standards. According to the Sixth Five Year Plan promulgated in 1982, the country's development plans emphasize the expansion and upgrading of key energy and industrial sectors, including that of fertilizer production-specifically phosphate and potash. Within the framework of the plan, the Ministry of Chemical Industry's development priorities are to: • Increase potash production by 150% to 50 kt (55,115 st). • Raise phosphate fertilizer production 21.2% to 2.8 Mt (3.1 million st), 46 kt (50,705 st) of which will come from new projects constructed and completed within the Sixth Five Year Plan, with projected new production of phosphate concentrate and complex fertilizer in the next decades totaling 500 kt (551,146 st). • Commence work to increase phosphate ore production by 8.33 Mt (9.18 million st). Facilities for 2.43 Mt (2.68 million st) will be completed and come on stream by 1985. • Commence work to increase iron pyrite ore production by 3.69 Mt (4.07 million st), facilities for 2.9 Mt (3.2 million st) will be completed and come on stream by 1985. • Verify 600 Mt (661 million st) of new phosphate ore reserves. Since the promulgation of the Sixth Five Year Plan, Chinese authorities have announced that 70 key construction projects will receive top priority in the implementation of the plan. These projects include five in the chemical industry area, including the construction of four fertilizer plants in Urumqi (Xinjiang), Zhenhai (Zhejiang), Beijing, and Lucheng (Shanxi), and a pyrite mine in Yunfu (Guangdong). In addition, by 1985 the state will expand or construct three major phosphate mines: Wangji in Hubei, Kaiyang in Guizhou, and Kunyang in Yunnan. Fertilizer Ratios In 1982, China's fertilizer production was slightly higher than 12 Mt (13.2 million st) and consisted of 80% nitrogen, 19% phosphate, and 0.19% potassium. By 1985, state officials project that fertilizer production will reach 13.4 Mt (14.8 million st) and consist of 78.4% nitrogen (10.5 Mt or 11.6 million st), 21.2% phosphate (2.8 Mt or 3 million st), and 0.39% potassium (52.3 kt or 57,605 st). To attain the world average using the country's 1985 projected production level for nitrogen, China will have to double its 1985 phosphate production to 5.76 Mt (6.35 million st) and increase its 1985 potassium production almost 80 times to 4.1 Mt (4.5 million st). These numbers demonstrate the seriousness of the fertilizer production problem in China today and the long-term nature of the problem's solution. Development Examples Yunnan is the third largest phosphate-rich province in China with verified deposits of 1.9 Gt (2.1 billion st). Despite this abundance, the province only mines around 3 Mt (3.3 million st) of phosphate rock annually. In June of this year, Yunnan announced its intention to initiate 39 development projects within the next two and a half years, requiring an estimated $200 million worth of foreign investment. The three areas receiving the most emphasis will be:

Jan 9, 1983

By T. W. Watson, D. R. Flynn

Measurements have been made of the thermal conductivity and electrical resistivity of two specimens of 0.005-cm (2-mil) Be-Cufoil over the temperature range -140° to +200°C. The thermal cmductivity of Be-Cu Alloy 125 was found to be significantly higher than that of Alloy 25, which had a higher impurity content. The thermal conductivity and electrical resistivity values obtained were in concordance with the Smith and Palmer relation for copper alloys which states that ? = 0.0239 (T/p) + 0.075 where A is thermal conductivity (W cm-' deg-'), p is electrical resistivity (microhm-cm), and T is absolute temperature (OK) , indicating that the Smith and Palmer relation can be used to predict the thermal conductivity of this type of Be-Cu alloy over the temperature range -140" to + 200°C to within an accuracy suitable for most engineering applications. THE National Aeronautics and Space Administration, Goddard Space Flight Center, Greenbelt, Md., requested the National Bureau of Standards to measure the thermal conductivity of 0.005-cm Be-Cu foil which was to be used to fabricate antennae for use in Radio Astronomy Explorer space craft. It was felt that measurements had to be made on the actual antenna material, rather than on a thick bar of similar material, since the cold-working and age-hardening properties of the alloy would make it very difficult, if not impossible, to place a thick bar in the same metallurgical state as the 0.005-cm material. As discussed in Section 111 of this paper, the thermal conductivity of many copper alloys can be computed rather accurately from electrical resistivity data using an empirical relation developed by Smith and palmer' and further confirmed by owell.' However, there has been very little work done on correlating thermal and electrical conductivities on Be-Cu alloys. We were reluctant to assume the validity of the Smith-Palmer relation on Be-Cu alloys because of the very large mass difference between beryllium and copper. As will be seen, however, our experimental results indicate that the Smith-Palmer relation is valid for the two alloys on which we made measurements. I) DESCRIPTION OF SAMPLES Samples of Be-Cu Alloy 25 and Be-Cu Alloy 125 were furnished to NBS in the form of rolled strip material, 0.005 cm thick by 5.08 cm wide. The Be-Cu Alloy 25 was purchased by NBS in the form of a continuous length of flat strip. The Be-Cu Alloy 125 was furnished to NBS by Goddard Space Flight Center in the form of two lengths of strip that had been formed into "tubing" of about 1.2 cm diam, with one side of the strip overlapping (but not connected to) the other side by about 90 deg. This "tubing" had been opened up to be flat and then rolled onto spools of about 3 cm diam. When unrolled, the strip would spring back into tubular form. Samples of both of the Be-Cu alloys were chemically analyzed by the NBS Analytical Chemistry Division. The beryllium content was determined quantitatively by the phosphate-gravimetric method to be 1.83 wt pct for Alloy 25 and 1.80 wt pct for Alloy 125. The two alloys were also examined by a general qualitative spectrochemical method for metallic elements. The Alloy 25 specimen contained between 0.1 and 1.0 wt pct Al, Co, Fe, and Si and between 0.01 and 0.1 pct Ni. The Alloy 125 specimen contained between 0.1 and 1.0 pct Co and between 0.01 and 0.1 pct Al, Fe, and Si. Other metallic elements present were in amounts less than 0.01 pct. The NBS Engineering Metallurgy Section measured the tensile strength, elongation, and Knoop hardness of both the Be-Cu Alloy 25 and the Be-Cu Alloy 125. These are given in Table I. The NBS Engineering Metallurgy Section also prepared photomicrographs of the two alloys; these are shown in Figs. 1 and 2.

Jan 1, 1969

By E. C. Smith

THE CHAIRMAN.-Mr. Earle Smith- has kindly offered to make some remarks in connection with segregation in the product, Mr. Smith: E. C. SMITH,* Cleveland, Ohio-I will start this off by a story of the code days of the American Iron and Steel Institute. In those days, Republic did not have a big strip mill, and the question came up of the check analysis of rimmed steel. I suggested that they let me be the chairman of the Committee on Accumulating the Information on the Variation of the Composition of the Ingots of Rimmed Steel. Somebody wanted to know why I wanted to be the chairman. I said, "We don't make any of the big ingots of rimmed steel, and no matter who makes them they are so bad that you don't dare publish the information. So if I collect it and hide it you can't charge me with having done anything that really disrupted the commercial situation. So, everybody furnished me with a rather complete story as to the horrible variations in big rimmed ingots. I took it out to my house and put it away, and it is still there. Now, segregation in the big ingot is no longer an "-academic-matter-as far as II am concerned. ¬I am in a situation like that of the German who was told in 1936 about the coming war. He said: "Until it is your throat that is going to be cut, you don't pay any attention to what is happening to the other man." That is the way with the problem that we have in front of us. Recently I have been told that the comptroller was questioning the payment for certain articles of stamped steel that had been made from rimmed steel, because upon check analysis of the rimmed steel it had been determined that these stamped articles were not within the compositions that were included in the specification, and therefore he as the comptroller had no alternative. It was not meeting the specification; therefore, no payment. So I would say to all of you: You can very seriously consider this matter of segregation now and on into the future on the basis of the fact that it is actually going to cost your companies, which are making these products, money unless there is some new idea about the infallibility of quantitative chemists who analyze some of these products or lawyers who read specifications. I don't know which man is going to be the major factor in the future. If the National Bureau of Standards could in some way show the specification writers the variation between good chemists analyzing for what they expect to be umpire results, the writers would certainly realize that some of the specifications to which we have calmly signed our names as being O.K. are well, as one man said to me, they might be filled by the devil, and they, certainly could be filled by the Lord, but they could not be filled by mankind. I would like to inject two or three things into a segregation study which I want you to think about, because I would be a little surprised if there is very much discussion of them. In the first place, we generally make steel in the United States in the basic open hearth, and I do not think there has been nearly enough consideration given to segregation within the bath before it moves into the ladle. I am sure that any of the people who handled the 9400 series of the NE series when it contained the 0.60 per cent silicon have more respect than they had previously for the segregation that is within the ladle; that is, before the metal reaches the ingot mold, the frozen ingots and the segregation in them. Another point to which I think we ought to give serious consideration is the segregation of iron oxide in the ingot-iron type of material, where the distinction between that and the steel segregation is that it is actually segregating iron oxide. Normally we are segregating some form of carbon or sulphur, or something like. that, with the stamping steel industry now coming down into the ranges of chemistry, where the segregation of iron oxide will be just

Jan 1, 1944

By Earle C. Smith

The Chairman.—Mr. Earle Smith has kindly offered to make some remarks in connection with segregation in the product, Mr. Smith: E. C. Smith,* Cleveland, Ohio—I will start this Off by a story oF the code days of the American Iron and Steel Institute. In those days, Republic did not have a big strip mill, and the question came up of the check analysis of rimmed steel. I suggested that they let me be the chairman of the Committee on Accumulating the Information on the Variation of the Composition of the Ingots of Rimmed Steel. Somebody wanted to know why I wanted to be the chairman. I said, "we don't make any of the big ingots of rimmed steel, and no matter who makes them they are so bad that you don't dare publish the information. So if 1 collect it and hide it you can't charge me with having done anything that really disrupted the commercial situation." So, everybody furnished me with a rather complete story as to the horrible variations in big rimmed ingots. I took it out to my house and put it away, and it is still there. Now, segregation in the big ingot is no longer an "academic " matter as far as I am concerned. I am in a situation like that of the German who was told in 1956 about the coming war. He said: "until it is your throat that is going to be cut, you don't pay any attention to what is happening to the otherman." 'That is the way with the problem that we have in front of us. Recently I have been told that the 'Omptroller was questioning the payment for certain articles of stamped steel that had been made from rimmed steel, because upon check analysis of the rimmed steel it had been determined that these stamped articles were nut within the compositions that were included in the specification, and therefore he as the camptroller had no alternative. It was not meeting the specification; therefore, no payment. So I I say to all of you: You can very seriously consider this matter of segregation now and on into the future on the basis of the fact that it is actually going to cost your companies, which are making these products, money unless there is some new idea about the infallibility of quantitative , chemists who analyze some of these products or lawyers who read specifications, I don't know which man is going to be the major factor in the future. if the National Bureau of Standards could in some way show the specification writers the variation between good chemists analyzing for That they expect to be umpire eel. the writers would certainly realize that some of the to to which we have calmly signed our names as being O.K. are— well, as one man said to me, they might be filled by the devil, and they certainly could be filled by the Lord, but they could not he me by mankind. I would like to inject two or three things into a segregation study which I Want you to think about, because 1 would be a little surprised if there is very much discussion of them, In the first place, we generslly make steel in the United States in the basic open hearth, and I do not think there has bee,, nearly enough consideration given to segregation German the bath before it moves into the ladle. I am sure that any of the people who handled the 9400 series of the NE series when it contained the 0,60 per cent silicon have more respect than they had previously for the segregation that is within, the ladle; that is, before the metal reaches the ingot mold, the frozen ingots and the segregation in them. Another pint to which I think We ought to sis serious consideration is the segregation of iron oxide in the ingot-iron type of material, where the distinction between that and the steel segregation is that it is actually segregat. ing iron oxide, Normally we are segregating some form of carbon or sulphur, or something like that, with the stamping steel industry now coming down into the ranges of chemistry, where the segregation of iron oxide will be just

Jan 1, 1945

By E. S. Machlin

The wzodel of Blandin and Diplunt;, generalized to include a phase factor, is applied to the carbon-carbon interaction in iron. Darken&apos;s "energetic" model is generalized to include not only first neighbor interactions but further neighbor interactions as well. On the bases of these generalized models relations are derived for the activity of carbon in both austenite and ferrite in terms of the carbon-carbon Pair interaction energies. A single function then yields the pair interaction energies consistent with the experimental activities of carbon in both ferrite and austenite. Thus, a simple explanation is given for the observation that the nearest-neighbor interaction between carbon is repulsive in austenite and attractive in ferrite. Certain consequences of this approach are explored. OnE object of the present paper is to attempt to take into account the consequences of electrostatic contributions to the carbon-carbon pair interaction energy for carbon as a solute in iron. Friedel&apos; has shown that oscillations in electrostatic potential are to be expected about a solute atom in a metallic solution. Blandin and 6lant6&apos; have shown that such oscillations yield an interaction energy between pairs of solute atoms that obeys the relation: W{ = A cos(2ftFri + 4>)/(kFri)3 [l] where kF = Fermi wave vector, ri = distance between solute atoms comprising the pair7 <p = phase factor dependent only on electronic nature of solute and solvent, A = coefficient dependent only on electronic nature of solute and solvent. Machlin3 found that Eq. [I] accurately described the pair interaction energy derived from short-range order measurements based on field ion microscope observations of dilute alloys of platinum. He also found that the value of the phase factor $ derived from residual resistivity measurements agreed well with that obtained from the analysis of the short-range order data. Harrison and paskin4 were able to predict the long-range ordering energy of 0 brass using Relation [I] and residual resistivity values to predict the value of the phase factor $. Machlin5 has repeated their analysis and applied it to the prediction of the long-range ordering energy in AgZn and AgCd with excellent agreement between prediction and experiment. Both A and $ are independent of the crystal structure. The Fermi wave vector depends uniquely upon the conduction electron concentration per unit volume in the spherical approximation of the Fermi surface. Thus, Eq. [I] is expected to apply to both fer- rite and austenite with only one set of values of A and $. Mossbauer studies6 yield the result that iron has one 4s electron. We shall make an assumption found to hold previously for platinum3&apos;7 and nikel, which is that only the s electrons are involved in shielding the perturbing potential of carbon. With this assumption, kF = 1.35 A-l. Although A and $ may be obtained from certain mdels&apos;&apos;&apos; we shall take A and $ to be empirical constants in the spirit of Kohn and osko.&apos; Thus, Eq. [I] involves two adjustible parameters. Consequently, two independent relations in A and $I are required in order to evaluate them for carbon as a solute in iron. We may use a recent analysis of Aaronson, Domain, and poundg who showed that Darken&apos;s energetic model,1° as well as others, can be used to describe the activity-temperature data for carbon in iron in both the aus-tenitic and ferritic phases. Darken&apos;s model takes into account only first neighbor pair interactions. For our needs, all neighbor pairs need to be taken into account. It is convenient to generalize Darken&apos;s model. The result for the partition function for austenite is: over the temperature range 800" to 1200°C and where the uncertainty corresponds to one standard deviation. Eq. [4] effectively yields only one relation. Another relation is required to obtain unique values for A and $. One property of Eq. [4] is that it is independent of crystal structure. Hence, data for a iron can be used to obtain another relation. To arrive at this relation we must generalize Eqs. [2] and [3] so that they may be applied to the bcc a iron. The result is that:

Jan 1, 1969

By W. R. Dengler

INTRODUCTION Shaft sinking represents a relatively small proportion of the activities involved in mine development. Because of this limited utilization, shaft sinking has been one of the most difficult functions to mechanize. Although shaft machines (muckers) were introduced more than 30 years ago, the first machines were low-capacity units, and machines of this type did not gain wide acceptance by the mining industry until the late 1950s. However, the increasing depth of underground mines and the es¬calating costs of labor have increased the benefits obtain¬able from high-speed shaft sinking. The result has been a growing need for high-capacity shaft machines. Most of the machines available at the present time have been developed by modifying existing equipment to increase the payload capacity and performance. AVAILABLE SHAFT MACHINES In general, shaft machines may be classified accord¬ing to the types of digging mechanisms and the mecha¬nisms of operation. The available digging mechanisms include clamshells, cactus grabs, front-end buckets, and backhoes. The mechanisms of operation can be classified as either pneumatic or hydraulic. Selection Criteria For efficient operation, the primary consideration in selecting a shaft machine is its capacity. The minimum capacity of the machine should match the capacity of the hoisting system at the ultimate depth of the shaft. In many cases, two machines may be needed to obtain a sufficient mucking capacity. The shaft dimensions and configuration often dictate the type of machine that may be utilized; for example, an overshot loader does not work well in a circular shaft that has a diameter of less than 5.5 m (18 ft). Similarly, a single Cryderman mucker is not suitable for a large-diameter shaft, nor is it applicable where very high sinking buckets are to be used. Other factors for consideration include the degree of material fragmentation, the abrasiveness of the rock, and the amount of ground water that is inter¬sected. Machine Descriptions Riddell Mucker: The Riddell mucker, illustrated in Fig. 1, was first introduced in 1948. This is one of the most common shaft machines in the medium-capacity range. The Riddell mucker consists of a hoisting and traveling mechanism that operates a clamshell suspended on cables. The early machines operated with a 0.3 m3 (10 cu ft) clamshell and had an hourly capacity of approximately 27 t (30 st). This type of shaft machine has gained wide acceptance throughout North America. Essentially, the Riddell mucker consists of standard components, such as the pneumatic tugger hoists that operate the clamshell. The carriage is suspended on rails that also serve as the blasting set, located immediately below the shaft timbers. To effectively position the clam¬shell in the shaft, the operator controls the carriage travel by means of wheels that are driven by a pneu¬matic motor. The Riddell mucker most commonly is used in rec¬tangular timbered shafts. However, some units have been installed with circular rails, allowing them to work in circular concrete-lined shafts. A popular practice with many Riddell muckers is to increase the capacity through the use of larger clamshells, often ranging up to 0.76 m3 (1.0 cu yd), in conjunction with more powerful tugger hoists. In some large rectangular shafts, two Riddell units have been used side by side to achieve a sufficient capacity. Cryderman Mucker: The Cryderman mucker, illus¬trated in Fig. 2, is another common shaft machine in the low- to medium-capacity range. Developed in the early 1950s, it also has gained wide acceptance throughout North America. Equipped with a 0.3 m3 (10 cu ft) bucket, the Cryderman mucker has an hourly capacity of approximately 23 t (25 st). The Cryderman mucker is operated entirely by means of pneumatic cylinders and a pneumatic telescopic boom. The boom is suspended from a sectional frame¬work that is usually located at one end of the shaft. The framework or headframe can be suspended from an independent hoisting system located either on the sur¬face or in the shaft. In large shafts of either rectangular

Jan 1, 1982

it may be clearly seen that one of the most rapidly increasing items in mining operations is the cost of the timber alone, to say nothing of the cost of installation. Consequently, any practical means that may be used to lengthen the life of mine timber will greatly tend to decrease mining costs and result in important economies in operation. The four principal agents by which mine timbers are destroyed are, decay, insect attack, fire and mechanical abrasion. Decay and insect attack are credited with more than 50 per cent of the total amount of timber destroyed in the mines. Numerous methods may be used to conserve mine timbers, such as better selection, preparation, storage and segregation. It frequently happens that good timber goes into places where poor timber would do as well, and timber of inferior quality is sent into places where only the best grade should be used. However, the most effective method of conservation is by treatment with some standard preservative to prevent decay. Some of. the benefits to be noted from the use of preserved timbers are; the reduction in operating costs by decrease in timber purchases; cuts down interference with mining operations due to timber failures on main haulageways; prevents excessive falling of roof in entries by maintaining timber in sound condition; conserves timber supplies and makes possible the utilization of inferior woods; reduces the danger of mine accidents; improves mine ventilation; lessens fire hazard. Our experience thus far with preservatives, while not of a sufficient period of time to establish just what length of life we may obtain from timber so treated, results obtained during the past four years indicate that the intelligent use of preservatives will effect sufficient economies in mine timber costs to justify the expenditures made for this purpose. MR. BAKER (Concluding): Now, if there are any questions you gentlemen would like to ask about our particular operations, I will attempt to answer them. J. H. EMRICK (Sullivan Machinery Company, Denver, Colo.) ; I was wondering how much penetration you get. MR. BAKER: We get between one-sixteenth and one-eighth of an inch; it is a dipping process. With pressure treatment you get-a greater absorption; that is, better than one-sixteenth of an inch. As long as there is no mechanical abrasion, it seems to serve the purpose. MR. EMRICK: Does that apply to the condition of the timber before it is treated? If it is perfectly dry, will it absorb more treatment than if it is partly green? MR. BAKER: Certainly; one of the things we do is to have it thoroughly seasoned before it is put into the preservative. We put some green timber into the mine once, and the fungus went after it right away. MR. EMRICK: What was the difference in the depth reached by the preservative? MR. BAKER: It hardly penetrated at all when it was green. It has to be sound and well seasoned. MR. EMRICK: How long was the timber dipped or treated? MR. BAKER: According to the seasoning. If it was well seasoned, it was left in the hot bath for an hour; if not so well seasoned, it was left for about a couple of hours. C. M. BILLINGTON (General Superintendent, Rocky Mountain Fuel Company, Lafayette, Colo.): Have you found it necessary to treat timber that has been charred? MR. BAKER: No. However, I suppose it has the sane effect; in lots of places they char timber for the purpose of treatment. MR. BILLINGTON: Have you ever tried lime and salt? MR. BAKER: No, this is the only thing we have tried, the creosote and the Aczol; the Aczol is a foreign product. WM. LITTLEJOHN: Which I is preferable, the Aczol or the creosote? MR. BAKER: I couldn&apos;t say as to that. MR. LITTLEJOHN: Have you had any tests as to the value of either? MR. BAKER: We have had some of the Aczol timbers in service for a little over four years; we have had some creosote timbers in service

Jan 1, 1926

By M. Garfinkle

LITERATURE data1&apos;3 have suggested that the resolved shear stress necessary to initiate slip in a particular slip system in tungsten single crystals is strongly dependent on the tensile orientation of the crystals. This orientation dependence is contrary to the critical resolved shear stress criterion. Because the Schmid factors for slip on particular {110}( I l l), {112}(Ill), or {123}(111) slip systems in a (100) oriented tungsten crystal are virtually identical to the respective Schmid factors for a (110) oriented crystal, slip should initiate on the same system in both orientations, independent of the values of the critical resolved shear stresses. Thus, it would be expected that, for a critical resolved shear stress model to hold, the proportional-limit stress for these two orientations must be similar. The expectation of similar proportional -limit stresses has not been borne out by reported experimental observations. Rose et nl.&apos; reported that the proportional-limit stress for crystals near the (110) orientation was 92,000 psi, approximately three times that of (100) oriented crystals (31,000 psi). Garlick and probst2 reported greater than a fourfold difference. Most recently, Beardmore and ~ull~ examined tungsten crystals with orientations along the edge of the standard stereographic triangle and showed a gradual increase in proportional-limit stress from 28,000 psi for the (100) orientation to 93,000 psi for the (110) orientation. Again, the difference was more than threefold. As has been emphasized by these investigators, the apparent gross variation of proportional-limit stress with orientation precludes any meaningful analysis of slip mechanics using a simple critical resolved shear stress relation. The purpose of the present communication is to report that, by use of refined strain-measuring techniques, the proportional-limit stresses for the (100) and (110) orientations are quite similar. Obviously, to determine accurately the value of the proportional-limit stress, which is by definition the stress at which nonlinear stress-strain behavior first occurs, the method of measuring strain must be capable of high accuracy. The investigators cited used as the measured elongation the crosshead displacement of the tensile machine. This method, however, introduces extraneous strain contributions from the load train. Because these extraneous contributions are considerable in the initial portions of loading (as has been well-documented in the literature) the proportional-limit stress measurement, dependent on the deviation of a line from linearity, can be significantly affected. During the course of a recent study, room-temperature strain was measured directly on several (100)-and (110)-oriented tensile specimens axially oriented within 5 deg of the desired direction. Each specimen was fitted with two foil strain gages mounted on opposite sides of the 0.08-in.-diam reduced section. The tensile specimens were loaded at a crosshead speed of 0.01 in. per min on an Instron Universal Testing Machine. Strain was monitored through an external bridge circuit in which the specimen strain gages comprised two arms. The bridge output was recorded against the applied load. A strain of 2 x 10"" could be readily detected by this method. Some specimens were subjected to conventional loading while the load for others was cycled between zero and continually increasing values until the first deviation from linearity was observed. The results of these methods were similar, and the stress at which nonlinear behavior occurred was considered the proportional-limit stress. The proportional-limit stresses measured in this study are approximately 5000 and 6500 psi for the ( 100) - and ( 110) -oriented crystals, respectively, a range of values almost a magnitude less than those reported previously. Representative curves are presented in Fig. 1. Because of the nature of the measurements made, the point of departure of a line from linearity is often debatable. While the load-strain curve for the (100) -oriented crystals made a relatively abrupt deviation from linearity, the curve for the (110) -oriented crystal was more gradual, so that the actual point of tangency may be at a lower load than reported. Thus, the difference in values for the proportional-

Jan 1, 1967

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes . The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper&apos; described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely. First, curves have been calculated for dipping discontinuities. Stern&apos; and Aldredge hose a few widely separated dip angles. Trudu confined his attention to small dips. Berel&apos;kovskiy and Zubanov computed gradient curves for widely separated dip angles. Unz as given the most complete solution, with a brief attempt to treat the three-layer case. Second, anisotropy can be taken into account. It seems geologically probable that layered materials have different vertical and horizontal conductivities. Cagniard, Maillet, and Pirson et up methods for finding an equivalent hypothetical isotropic medium. Standard interpretation methods can be applied to this, and the actual medium can then be deduced. Belluigi&apos;" discounts the practical importance of anisotropy; Geneslay and Rouget do not agree with his conclusion. Third, the effect of variable resistivity in a layer can be considered. Keck and Colby" examine the mathematics of an exponential increase in a surface layer. Several authors, for example, Stevenson,&apos;&apos; consider a continuous variation of resistivity with depth. The present paper deals with a linear variation of resistivity in a surface layer. Geologically, surface variations should be expected. Unconsolidated materials such as glacial drift show marked irregularities over short distances. The effects of weathering change with depth. The moisture content of material above the water table may vary from a dry sand to a saturated clay, and both of these will be changed by rainfall. Figs. 1 to 6 present apparent resistivity curves to show the effect of a variable surface layer. In all cases resistivity varies linearly with depth down to a depth of one unit. Material beneath this depth has constant resistivity. Electrode separation is plotted in depth units. Insets on each figure show the corresponding cross-sections, plotting true resistivity against depth. To illustrate, consider curve A of Fig. 1. The true resistivity of material at the surface of the earth is taken as 0.4 units. Resistivity increases with depth, reaching a value of 1.0 at 0.5 depth units and 1.6 at 1.0 depth units. Below a depth of 1.0, all the material has very low resistivity (zero, for purposes of calculation). Curve A in the main part of Fig. 1 shows how apparent resistivity varies for this case as the electrode spacing is increased. To illustrate further, curve E of Fig. 4 corresponds to true resistivity of 1.2 units at the surface, 1.0 at a depth of 0.5 units, 0.8 at a depth of 1.0, and 1.5 for all depths greater than 1.0. Apparent resistivity curves have been plotted logarithmically so that the shape of the curves becomes independent of the units, giving the curves wide validity. A certain drift-covered area, for example, shows a gradual decrease of resistivity from 230 ohm-meters at the surface to 150 ohm-meters at the bedrock surface, 275 ft down; bedrock resistivity is 800 ohm-meters. Curve E of Fig. 5 indicates that true resistivity decreases from 1.2 units at the surface to 0.8 at a depth of 1.0, then increases abruptly to a constant value of 4.0 units. Since resistivity and depth ratios are the same, this can be used to predict the field curve. For Fig. 5, multiply true resistivity and apparent resistivity by

Jan 1, 1955

By Ian MacGregor

INTRODUCTION I retired in 1977 and have been enjoying myself ever since doing odd jobs for various people - on occasions, politicians. I commend it to you as post retirement - get involved in situations that nobody else will take on. It produces all sorts of excitement, it is a lot of fun and, courtesy of the media, you provide great raw material for their current Punch and Judy shows. The example of the adventures in the Escondida financing made me think about the history of the minerals industry in the United States. In order to see more clearly what is going to happen in the future, we have to look at the past and what we have learned, and try to extrapolate from that a scenario for the future. This paper is about global material cycles and the financial needs of the extractive industries. Since about 2,000 years B.C. we have been living in the Iron Age. Since about 4,000 B.C. we have been living in the Copper Age. These have been the two foundations of modern industrial society. Understanding the use of metals and materials helps us understand the civilization in which we live today. Let me focus more closely on the United States, particularly in this century. In the first two-thirds of this century the United States was growing and expanding and developing. It was providing for its inhabitants a society which was enjoying the benefits of a rising standard of living, improved opportunities and the ability to support a population growing at quite a dramatic rate. It is still growing. In the Department of Commerce, there is a clock that shows how many people there are in the United States. It turns all the time; the numbers are going up. On January 21,1980, when Ronald Reagan was sworn in as President, the number on that clock was a little over 220 million, and in the last week before he left, it was travelling towards 245 million. During his period in Washington, we have added , the equivalent of one total state such as California. That gives the dimensions of the U.S. appetite for raw material inputs. The inputs are of critical importance. COMPARATIVE ADVANTAGE During the first two-thirds of this century, the minerals sector enjoyed comparative advantages. There was a clear understanding of the importance of minerals enshrined in the tax legislation of the country from the early decades of this century - the depletion allowance. No other country identified as clearly that the supplies of minerals were finite. As they are used up, just as with a wearing-out machine, one must get capital back to replace the resource when the time comes. Within the last decade, that idea has been questioned and criticised. It is now seen as giving money away to a preferred part of the economy, instead of recognizing what depletion is all about. In previous times it insured that the U.S. always was able to regenerate the capital in its minerals industry, so that it could remain competitive. The U.S. had plenty of everything, including energy. We had a growing population. Equally important, we had an agriculture that led the world in productivity, even as far back as the turn of the century. It continues to do so. We still retain that comparative advantage, an ability to produce our foodstuffs in quantity and quality at excellent cost. Look at another ingredient of our comparative advantage, the energy position. We ran through the first two-thirds of the century with ever- decreasing energy costs. In the 1940s and 1950s the coal industry went into a decline. Why? Because the $3.00 - $5.00 a ton cost of mining coal in the U.S. represented relatively expensive energy. A ton of good grade bituminous coal contains 25 million BTU&apos;s. $0.20 a million BTU&apos;s represents $5.00 a ton at the pithead. That price was undermined by the increasing ability to find petroleum at even lower costs. At the apex of the growth of development of the American dominated

Jan 1, 1990

By M. E. Wadswort, A. S. Peck

Infrared data disclose that phenacite reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. The absorption band characteristic of the antisymmetrical C = 0 oleate structure appears at a spectral wavelength of 1623 cm-&apos;. Chemisorption also results in the displacement of OH- and silicate from the mineral surface. Infrared absorbance at 1623 cm-1 is correlated with float-ability at different pH for -60-mesh phenacite particles. Phenacite, Be2SiO4, is an ore mineral often associated with quartz, microcline, and chrysoberyl in pegmatites and mica schist. Experimental phenacite beneficiating processes have been confined principally to the flotation of low grade ores occur-ing in several mountain ranges of Utah and Nevada. The U.S. Bureau of Mines &apos; has recently reported on the separation of phenacite from ore deposits of Mount Wheeler, Nev. Infrared techniques were previously applied by the authors to characterize the role of sodium oleate and oleic acid in the flotation of several non-sulfide minerals.23 A parallel study was projected to the flotation of the orthosilicate mineral phenacite with oleic acid. Infrared spectra provided a &apos;molecular fingerprint&apos; of the mineral surface and permitted identification of the reaction mechanisms. Infrared data were complemented with flotation and chemical tests. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation, for which data are presented in graphical or spectral form, are described in chronological test order. Phenacite crystals from Mt. Antero, Colo., were obtained from Ward&apos;s Co., Monterey, Calif. The crystals were fragmented in a porcelain mortar to -60 mesh and then pretreated with 0.5 molar HC1 for 15 min to remove iron. Then, the mineral particles were washed free of acid with distilled water and dried. Part of the dried material was ground to a fine powder with a Fisher Grinder using an agate mortar and pestle. Next, the powder was placed in a graduated cylinder and mixed with 500 ml of distilled water. The mineral in suspension was decanted from the settled fraction after 5 min, and the colloidal suspension was used for adsorption tests in which a high specific mineral surface area was required for adsorption and infrared analysis. Conditioning was performed in 50 ml glass centrifuge tubes for both infrared and flotation test determinations. Twenty ml of colloidal suspension was used for the infrared adsorption tests. One and a half g of deslimed -60-mesh HCl pretreated phenacite was added to 20 ml of distilled water for flotation conditioning tests. Six mg of oleic acid was used for each infrared adsorption test, and 0.2 mg of oleic acid was used for the flotation conditioning tests. HCl and NaOH were used for pH modification. The pulps were stirred at a speed of about 1500 rpm for 3 min. Then, the solids were separated out and either dried at 50°C or immediately transferred to a float cell. The pH of the residual liquid was determined with a Beckman Zeromatic pH meter. The flotation procedure is described as follows: 1) A 325-1111 glass micro-float cell was filled with distilled water. 2) Conditioned mineral was placed in the cell and the pulp was aerated through the glass fritted bottom at 7 psi pressure. 3) Floated mineral was skimmed from the cell with a glass slide until flotation ceased. (The end point was reached in all tests in less than 2 min.) 4) The flotation products were dried, weighed, and the recovery was calculated. Samples for infrared analysis were made into mulls using either oleic acid or series 13-21 Halocarbon oil obtained from Halocarbon Products Corp., Hacken-sack, N.J. The mulls were placed between two sodium chloride windows. A characteristic phenacite infrared band at 1868 cm-&apos; was used as an internal standard for quantitative determinations in which absorbance at this position was quantified by the baseline-tangent method4 and related to absorbance at 1623 cm-&apos;. The ratio obtained by dividing absorbance at 1623 cm-&apos; by absorbance at 1868 cm-&apos; was defined as an absorbance quotient for use in graphical presentation.

Jan 1, 1968

By P. G. Winchell, A. J. Heckler

An experimentally simple method for determining the effect of alloying elements on the activity of carbon is validated in Fe-Ni-C austenite. The technique consists of the equilibration of carbon between specimens of different nickel contents within a sealed silica capsule. The attainment of carbon equilibrium within each capsule is evidenced by: 1) in each capsule specimens of the same nickel content attained the same final carbon content regardless of their initial carbon contents, 2) in every capsule the final carbon content was reached for most nickel contents by carburizing and by decarburizing. The activity of carbon attained within each capsule was calculated from the carbon content of a binary Fe-C alloy placed within the capsule, and from the activity coefficient of carbon in the Fe-C system as found by Smith for CO/CO2/C equilibrium. The activity of carbon in Fe-Ni-C austenite determined by this method at 1000°C agrees with prior work by Smith, who used mother method. The measurements are extended to 800°and 1200°C. The activity coefficient of carbon 7c, in Fe-Ni-C austenite is given by: where xC is the ratio of carbon to metal atoms and XNi is the ratio of nickel to metal atoms and where the standard state is chosen such that yC = 1 as xc approaches zero in Fe-C alloys. This equation appears to be valid for xni < 0.3, and 1073° < T<1473°K. ThE activity of carbon in Fe-C austenite has been measured by smithL at 800°, 1000°, and 1200°C. Smith has also studied the effect of nickel on the activity A. J, HECKLER and P. G. WINCHELL are Graduate Student and Associate Professor of Metallurgical Engineering, respectively, School of Metallurgical Engineering, Purdue University, Lafayette, Ind. This paper is based on a thesis submitted ty,to Purdue University, in partial fulfillment of the requirements for the degree of M.S. in Metallurgical Engineering which A. J. HECKLER received from Purdue in January 1962. Manuscript submitted August 13, 1962. IMD of carbon in austenite at 1000°C. In both these studies the activity of carbon was fixed by a flowing CO-C02* *Gas mixtures of hydrogen and methane were also used in Ref. 1 but these results are not incorporated in Ref. 2 or in the present study. gas mixture. In the present work, Smith&apos;s results for Fe-Ni-C austenite are confirmed and extended to 800" and 1200°C by a different experimental technique. EXPERIMENTAL PROCEDURE In essence the experimental technique consisted of enclosing specimens of various nickel contents in an initially evacuated silica capsule and annealing the capsule until carbon equilibrium was attained among the enclosed specimens. The carbon activity obtained within the capsule was determined from the final carbon content of the binary Fe-C alloy included in each capsule and the results of smith.&apos; In order to evaluate this method the absence of nickel transfer between specimens must be established and the attainment of carbon equilibrium between samples must be assured. The absence of nickel transfer was demonstrated in the case of an originally pure iron sample which was annealed at 1200°C in a capsule with a 27.3 at. pct Ni alloy. The final nickel content of the iron specimen was less than 0.1 at. pct, a change which has a negligible effect on carbon activity. The attainment of carbon equilibrium was demonstrated within every capsule and in over half the results by achieving the same final carbon content in a sample which carburized during equilibration and in a sample of the same nickel content which decarburized during equilibration. The base Fe-Ni alloys were vacuum melted from Ferrovac E or electrolytic iron and Mond or electrolytic nickel. The samples were rolled and/or swaged and their carbon content adjusted to the desired pre-equilibration level either by methane-hydrogen carburization or by direct carbon transfer from a graphite source in a sealed silica capsule. As mentioned previously, high-carbon and low-carbon samples were prepared for most nickel levels in each capsule. The specimens were cleaned and

Jan 1, 1963

By J. W. Sandelin, L. S. Birks

The group five metals, vanadium, niobium, and tantalum all show cold-rolled textures of {100)(011) and {112)(0ll) with a preference for the (100) in vanadium and niobium and for the {112) in tantalum. Recrys-tallization texture of (100) and (111) was reported1 for vanadium after annealing (no temperature stated). For tantal~m ,~ annealing below 1200°C strengthened the (112) texture but the (111) texture increased and was predominant as the annealing temperature was raised to 2500°C. Annealing niobium up to 1100°C strengthened the ( 100) texture and developed a weak (111) texture.&apos; In the present work niobium has been annealed up to 2000°C. Nearly 70 pct of the grains showed {111) texture with only a weak (112) component and an insignificant (100) component remaining. In addition, double-crystal rocking curves were used to follow the increase in crystal perfection of the grains with increased annealing time. Material and Treatment. Samples i by 4 in. were sawed from & -in.-thick cold-rolled niobium sheet obtained from Wah Chang. Chemical analysis of the material showed it to be 99.4 pct pure with tantalum as the major impurity. Individual pieces were annealed for 2, 15, 30, and 60 rnin in a vacuum of 10&apos;* Torr using an rf generator. They were etched until the grain boundaries were well-defined, Fig. 1. Average grain size varied from 1 mm for 2 min annealing to 2 mm for 60 rnin annealing. Experimental Results. Preferred Orientation. The orientations of 97 of the 117 grains in the specimens of Fig. 1 were determined by back-reflect ion Laue patterns. A General Electric 10-cm-diam cylindrical camera was used rather than the conventional flat camera in order to record more of the low-index spots. The method proposed by Forest, Barton, and schieltz4 was used to transform the cylindrical film patterns to standard stereographic projections. Table I gives the compilation of data. Even 2 rnin anneal at 2000°C is sufficient to yield a strong (111) preferred orientation, and the percentage of grains with this orientation increases steadily with annealing time at the expense of all other orientations. Crystal Perfection. X-ray topographs were taken of each specimen in both the (111) and (112) orientation using the method described by Birks and Grant.&apos; As the anneal time increases, the grains become larger and the individual reflections become slightly more uniform in intensity, indicating an increase in crystal perfection. For a more quantitative measure of crystal perfection, it was necessary to measure the double-crystal rocking curve. The spectrometer employed was a Gaertner instrument of Compton design. LiF was chosen for the first crystal because the (400) reflection with d spacing of 1.05 AU is a good match to the (222) niobium reflection with d spacing of 0.95 AU. CuKp radiation was used in order to further reduce the d spacing mixmatch correction.&apos; A variable aperture was placed between the LiF and the niobium specimen so that a single grain or even a small portion of a grain could be examined. Fig. 2 shows typical rocking curves for the four annealing times. For the 2-min specimen, a single peak is observed with 10&apos; of arc full-breadth at half maximum. As the annealing time is increased to 15 or 30 min, several sharper peaks of 40 to 80" breadth can be seen within a single grain. After 60 rnin anneal only a single peak of about 30" is observed. Table I1 shows the corrected rocking curve breadths and the dislocation densities, ND. The latter were calculated from the equation7 where W is the corrected rocking curve breadth at half maximum in radians and b is the effective Burger&apos;s vector. For (110)(111) slip in niobium, b is 2.86 AU. Discussion. The annealing of cold-rolled niobium at 2000°C causes rapid preferential growth of grains with {ill} orientation. After only 2 rnin annealing time, 35 pct of the grains have the (111) orientation, and after

Jan 1, 1968

By Robert Gillham, Victoria Yablonsky, Grover R. Castle

INTRODUCTION The commercial paper market, unique to the United States, is a direct exchange of funds between high-grade borrowers and large lenders; because it eliminates both the bank&apos;s role as middleman and also some significant transaction costs, commercial paper is the lowest cost short term instrument in the world. For this reason, virtually all borrowers would like to enter the market, but only issuers with the highest rating from Moody&apos;s and Standard & Poor can attract purchasers at the best rates. COMMERCIAL PAPER The commercial paper market, in existence for over 100 years, has traditionally been used for short-term financings, with most paper maturing within 30-45 days. Under the U. S. Securities Act of 1933, (section 3(a)3) industrial paper can avoid registration only if it matures within 270 days and is used for current transactions. It was first used to finance the short-term seasonal working capital needs of manufacturing companies. Since World War II, commercial paper use has grown steadily, serving in the 1950&apos;s as the market in which finance companies financed the explosion in consumer credit purchases of heavy consumer durables. LETTER OF CREDIT BACKING As far as is known, the use of letters of credit to support energy-related commercial paper began about 13 years ago with an arrangement to finance the nuclear fuel for Con Edison&apos;s Indian Point 3 Plant. Goldman, Sachs was the architect of this financing and Chemical Bank provided the letter of credit support. After an early burst of interest, this type of financing wobbled severely in the difficult credit markets of the mid-seventies before regaining serious momentum in 1976 and 1977. A mining project would not normally qualify as a borrower in the commercial paper market because of its credit standing and because its large capital needs require long term financing. However, lately, commercial paper has begun to take the place of a bank term loan in limited recourse project financings. L/C backed commercial paper took this new and startling turn in 1982 when it was used as part of the $700 million financing for the development of the Newlands-Collinsville coal mines of Mount Isa Mines Ltd. in Australia. This was the first use of L/C backed commercial paper in a long-term limited recourse project financing. First Boston acted as financial advisor and, again, Chemical Bank provided sole letter of credit support of $155 million. The $785 million BHP financing for the acquisition of the Queensland (Australia) coal assets of Utah International from General Electric Company followed the next year; there we acted with two other Front Banks to provide $270 million of L/C support. These two important transactions indicate that not only has commercial paper become an integral part of a long-term financing package, but also that it is no longer the exclusive domain of the best known U. S. companies. Lesser-rated companies and a multitude of foreign borrowers have gained access to this "exclusive club." How has this become possible? OPERATION OF AN L/C An instrument of the commercial banks, the "direct pay" letter of credit, has enabled lesser-rated companies to issue commercial paper in their own names. The letter of credit allows the issuer to substitute the credit rating of the supporting bank for its own. The L/C in effect allows a lesser-rated company to rent the bank&apos;s credit rating. This upgrading is possible because the bank is unconditionally obliged to pay the note-holders at maturity and then turn to the Issuer for reimbursement. The Issuer commonly "rolls over" a new short-term issue and reimburses the supporting bank from the sale of the new issue until cash flows from the project allow the borrower to reduce the level of paper outstanding. The commitment for an L/C facility, up to 12 years in the case of the Broken Hill transaction, governs the life of the commercial paper tranche of the financing. The term of the L/C commitment thus has the power to extend the ordinary 30-45

Jan 1, 1985

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined because it is used both as a rock term and as a particle size term. Actually most persons using the term clay realize that it has a double meaning and in most instances define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it so that the definition has to be general. Clay is a natural, earthy, fine-grained material composed largely of a limited group of crystalline minerals known as the clay minerals. Many definitions state that a clay has the property of plasticity when wet, but some clays are not plastic, i.e., halloysite and flint clay; however, most clay materials are plastic when wet. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on some grade scales. Soil investigators and mineralogists generally use 2 microns as the maximum size. The Wentworth scale&apos; defines clay as material finer than approximately 4 microns. Grim&apos; has found it convenient to use the term clay material for any fine-grained, natural, earthy, argillaceous material and in this way can include clays, shales, or argillites, and some soils if they are argillaceous. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, still the term is generally understood by all who use it. Clay is an abundant natural raw material and has an amazing variety of uses and properties which will be discussed in this chapter. In order to understand better the relationships between the clays and their uses, a brief discussion of the structure, chemical composition, and identification of the clay minerals is given. Mineralogical Composition of Clays Clays are composed of certain groups of hydrous aluminum, magnesium, and iron silicates that may contain calcium, potassium, and other ions, which are called the clay minerals, and other minerals of variable composition, which are nonclay minerals. Both clay minerals and nonclay minerals influence the properties of a clay material. In order to understand the relationship between clay minerals and the properties of a clay material, a short summary of the structure and composition of clay minerals is necessary. Any scheme of classification tends to impose a certain rigidity and as new and additional data become available it is necessary to revise classifications. Brindley3 has discussed the classification and structural mineralogy of clays in very lucid fashion and chose a classification based on structural features and chemical composition. Grim2 proposed a tentative classification which is based on the structural attributes of the various clay minerals. This classification is relatively simple and workable, and is shown as follows: I. Amorphous Allophane group II. Crystalline A. Two-layer types (sheet structures composed of units of one layer of silica tetrahedrons and one layer of alumina octahedrons). 1. Equidimensional Kaolin group kaolinite, dickite, nacrite 2. Elongate Halloysite group

Jan 1, 1960

By William J. Wiehagen

The training of mining personnel is a large and continuing activity for the mineral industries. Although safety and skills training has long been recognized as an essential element for reducing injuries and improving productivity, the research literature lacks definitive reports documenting the specific value of such training. The training literature presents a variety of testimonials as to the "benefits of training," but lacks data that specifically tie that training to the performance of the worker.

Jan 1, 1983

By M. A. Stoakes, H. D. S. Miller

Surface subsidence is becoming an increasingly important factor in the economics of mining Louisiana salt domes due to, amongst others, excessive shaft deformations and land loss to encroaching sea water. The vast majority of subsidence studies have been undertaken on bedded, tabular deposits. It is important to understand the causes of subsidence due to mining domal salt and how it can be minimized. The paper will review the major differences between subsidence caused by domal and tabular evaporite mines, the problems encountered in predicting subsidence, the factors that influence subsidence and, finally, possible alternative mining methods.

Jan 1, 1986