Search Documents

By M. H. Gaskell, D. M. Kehn, G. T. Pyndus

A correlation of the bubble point pressure for black oil systems is developed using the standard physical-chemical equations of soiutions. The correlation is based on 158 experimentally measured bubble point pressures of 137 independent systems and is expressed in terins of the usually measured field pnrameters— flash separation gm-oil ratio, rank oil gravity, total gas gravity, and reservoir temperature. The data were obtained on systems produced in Canada, Western and Mid-Continent01 United States, and South America. The average error (algebraic) in the representation is 3.8 per cent, and the maximum error encountered is 14.7 per cent. INTRODUCTION In the absence of experimentally measured properties of reservoir fluids, it is often necessary for the field engineer to make estimates regarding the fluid properties based on the usually measured producing parameters. To aid in these estimations, various correlations have appeared in the literature in recent years. Among the pertinent properties of interest is the bubble point pressure. A correlation for this parameter has been reported by Standing'. However, this correlation was based essentially on California produced crudes and this limitation was pointed out with its presentation. The correlation presented in this paper utilized data on crude oil systems from Canada, Wes- tern and Mid-Continental United States, and South America. CORRELATION DEVELOPMENT The basic assumption used in this development is the same as employed by Standing', There is a wide variety of ways to combine these parameters; however, in this instance the combination was made on the basis of Henry's law2. Accordingly, the relationship proposed is Although Eq. 2 defines an individual system, it is of limited value since H' is a function of gas-phase composition and the system temperature. It was observed that for the systems where the bubble point was measured at several temperatures that the ratio of the bubble point pressures and the ratio of the corresponding absolute temperatures (R) were practically identical. Thus, for correlation purposes the bubble point pressure may be taken as a direct function of the absolute temperature. This relation is valid only for those systems that are not near the critical point. Accordingly, this correlation will be inadequate for systems in the region of the critical point. The solubility of the various hydrocarbons found in the gas phase increases with the molecular weight. Thus, the saturation pressure should be inversely related to the gas gravity. Applying these principles to Eq. 2 and rearranging terms gives: The variables 02 the left side of Eq. 3 were designated as the "hubble point pressure factor". The number of mols of tank oil per barrel is a function of the "mclecular weight" of the tank oil. Although the tank oil is a complex mixture, it was assumed for the purposes of this correlation that a unique molecular weight could be assigned to a given oil. This was designated as the "effective molecular weight", and was related to the oil gravity, This empirical relationship was developed simultaneously with the correlation by assuming values of M,. and working to obtain a smooth curve for both the correlation and the effective molecular weight. The relationship between the oil gravity and the effective molecular weight used in this correlation is shown in Fig. 1. The effective molecular weight is somewhat higher than the molecular weight of the C fraction. The difference between these values is largest for the low-gravity systems. It is noted that this effective molecular

By Nicholas J. Grant, Hanna Ibach, Bill C. Giessen

The system Ta-Rh was investigated over the entire comnposition range using metallogvaphic and X-ray techniques as well as thermal analysis. Terminal solubility limits, solidus temperatures, and the crystal structures of two new intermediate phases were determined. There are five intermediate phases: o, tetragonal, isostructural with o(Fe-Cr); a1, orthorhomnbic : a2, orthorhombic, isostructural with CozSi; 0 3, a high -temperature phase of unknozun structure; and a TaRh3, cubic, AuCu3 structure. a, aL, a,, and a melt peritectically; and a TaRh, has a maximum melting point. Five peritectic and one eutectic reactions occur. THE Ta-Rh phase diagram has not been fully treated in the literature; however, two inter metallic phases have been described.&apos;-&apos; This study attempts to work out the diagram covering the details of phase boundaries as well as the crystallography of the intermediate phases. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by National Research Corp., Cambridge, Mass., and rhodium powder of 99.9 pct purity, supplied by Bishop Co., Malvern, Pa. Analyses as given by the manufacturers are presented in Table I. In addition to the spectroscopic analysis, an oxygen analysis has been made of the tantalum powder. After preliminary trials, the standard procedure employed in making the alloys was as follows (see Ref. 4 for further details). The powders were weighed, mixed manually, compacted under 16,000 psi, and arc-melted at not more than 500 amp under thoroughly titanium gettered welding-grade argon of 400 mm Hg pressure. The gettering process was repeated after each melt. It had been shown previously5 that under these conditions no oxygen pick-up exceeding 0.001 pct in a hafnium button could be detected. The buttons, ranging from 5 to 10 g in weight, were inverted or, if possible, crushed and remelted three times. Melting presented no difficulty, except for tantalum-rich al- loys, which showed considerable spashing during melting. The average weight loss of 1 wt pct rose to 2.5 wt pct in these cases. Subsequent melting, however, resulted in losses of less than 0.1 wt pct. The melts obtained frequently showed small in-homogeneities, mostly in the tantalum-rich part of the system below 25 at. pct Rh. This was not due to insufficient blending of the elements, but to crystallization taking place from the cooled bottom. This condition was not improved by further re-melting; therefore the following precautions were taken. Cross sections of as-cast buttons were made. For the investigation only buttons were used where these inhomogeneities did not exceed 1 at. pct (estimated from the amounts of haSeS resent). In addition, only the center portions of such buttdns were utilized to minimize errors. Smaller buttons showed smaller concentration gradients and were used as a check. Finally, all alloys were homogenized to eliminate coring (see below). After this, the error in alloy composition due to inhomogeneity was cl at. pct. In order to confirm the concentrations of the alloys and to provide an impurity check, wet-chemical analyses and oxygen-fusion analyses of four key alloys were carried out. The results, together with the concentrations as calculated with the weight balance method, are presented in Table 11. It was found that for three alloys the agreement is very good (< 0.2

Jan 1, 1964

By M. H. Childs, K. E. Merklin

Blast furnace feed specifications are being revolutionized because of the large increase in iron pellet production from low-grade ores of the Lake Superior region. Recent laboratory findings aimed at a better understanding of factors influencing the physical quality of pellets produced from taconite concentrates are reviewed. Tests for determining better product quality, the effects of additives, and production factors are discussed. The current revolution in specifications for blast furnace feed is typified to a great extent by the recent tremendous growth in iron ore pellet production from low grade ores of the Lake Superior region. Indeed, pellets are responsible, at least in part, for many of the stringent new requirements that are being placed on the suppliers of furnace raw materials. As the tonnage of pellets going to the steel mills increases, more and more attention is being turned to the detailed characteristics that make this product an ideal blast furnace feed. Control of quality in pellets is similar to that of any other product. A basic understanding of the factors that are encountered in their production, from the crude ore through to the finished product, is required, along with careful process supervision and frequent quality checks. Normally, chemical grade is not a problem. This usually can be controlled within the desired specifications by minor operating variations in the con- centrator. While future changes in requirements may result in the need for self-fluxing pellets1 or other chemical changes, today&apos;s quality demands center primarily around the physical characteristics of the pellets. It is in this area that many of the recent laboratory studies have proven helpful to the operating plants. A better understanding of the physical factors involved in pelletizing has provided the basis for a continuing program of quality improvement. Tigerschiold and Ilmoni2 and Cooke with various associates are responsible for the development of much of the basic understanding of the pelletiz-ing process. These earlier findings have served as a most useful background for this work. LABORATORY PROCEDURES Magnetite concentrates produced from eastern Mesabi Range magnetic taconites were used for all of the work reported herein. The sizing and chemical analysis of a random sample are shown in Table t Additives usually are mixed with the concentrates in taconite plants before pelletizing to improve the strength characteristics of the unfired balls. Ben-tonite, soda ash, and coal are in common use. The bentonite used in these studies was of the Wyoming sodium type; the soda ash was a standard commercia1 brand. Anthrafines were used where coal was called for. The procedure for making batches of balls at the Hibbing Laboratory is as follows: In an especially designed mulling equipment 2800 g of dry ore are mixed for 10 min with the desired additives. Water is added and mixing continued for 1 1/2 min. The charge is removed from the muller and put through a mechanical shredder to break down any lumps that may have formed. sixty previously formed seed balls are placed in the balling drum, which is in fact a 6 x 16-in. diam airplane tire turning at 53 Wm. Two thousand grams of the shredded concentrate and additive mix are fed by hand into the tire at a con-

Jan 1, 1961

By W. T. Turrall, M. J. Cook

A discussion of modern developments in beneficiation of fine sizes of anthracite, this paper includes a description of the plant flowsheet, an analysis of operating results, and a summary of fundamentals of mineral separation relative to plant operation. DURING the past several years Lehigh Naviga-tion Coal Co. has installed equipment at Tamaqua and Lansford collieries for cleaning and sizing No. 4 buckwheat —3/32 + 3/64 in. and for recovering and cleaning flotation coal —20 + 200 mesh at Tamaqua colliery. Papers describing some of these installations have been presented to AIME. At Coaldale colliery, however, methods used to clean fine coal were inadequate and inefficient. Management decided upon a thorough investigation of all existing processes before building a plant to treat the combined three sizes mentioned. Investigation, carried out on company property and at other plants, entailed a study of hydrotators, hydroclassifiers, tables, spirals, flotation machines, methods of screening, and methods of dewatering. On the basis of this investigation a flowsheet was designed which necessarily excluded many processes in use, and the writers wish to emphasize that no criticism is implied by omission of processes or machines. A determining factor in selection of many machines was the policy of standardizing equipment wherever possible. Flowsheet and Operational Data The first principle to be considered in designing of any plant is efficiency of cleaning as related to laws of classification. Beneficiation of coal may be described as separation of two materials having different specific gravities. Although there is an inherent ash content even in the purest coal which slightly affects its specific gravity, it is recognized that many particles are true middlings. The percentage of these particles allowable in the final product depends upon the ultimate ash, or specifications of the consumer. Richards in his study of free settling and hindered settling classification&apos; determined that particles of equal size and different specific gravities had unequal settling velocities. He also determined a definite size relationship for equal settling velocities with free settling and hindered settling conditions. Considering the design of machines used to clean No. 4 and No. 5 buckwheat, it may be assumed that both free settling and hindered settling conditions exist and that ratio of size for practical operations is between the established values. The essential factor is that the more efficiently and closely sized the feed is maintained, the more nearly perfect the resulting separation. Flowsheet design was governed primarily by factors related to the 1200 to 1500 tons per hr feed to the main plant. It should be stressed that because of the many sources of supply from mine and stripping, the physical characteristics of this feed varied considerably. The most significant influence was varying percentage of fines, necessitating that all machines be capable of operating under maximum peak load during periods of surge. Since cleaning practice is a wet process, about 9000 gal per min containing 14 to 15 pct solids, or 350 tons per hr, must be treated. This slurry contained all the fines, or —3/32 in., but also percentages of oversize, up to 1 % in., dependent on spills or breaks in screen jackets, a not uncommon occurrence in preparation plant practice. The flowsheet developed is shown in Fig. 1. Circled numbers represent points of sampling. Table I gives operational data including size, ash by size, composite ash, rate of flow in gallons per minute, percent solids dry weight, and average tons of solids per hour. It should be noted that these results are subject to human error in sampling practice. Detailed information reported is a representative evaluation of plant operation.

Jan 1, 1954

By L. R. Page, J. J. Norton

EFFECTIVE methods for determining grade and reserves of pegmatites in advance of mining have been developed in recent years. When intensive work began on the economic geology of pegmatites during the early years of World War 11, it was widely believed that grade and reserves could be estimated only in a most general way. The literature indicated that not all pegmatite deposits are unpredictable, but statements emphasizing unpredictability and irregularity seem to have been more widely accepted. Many standard references reflect the prevailing opinion that minerals: are unsystematic in their occurrence in pegmatites. Pegmatites have been described as "notorious for their irregular structure," and minerals within pegmatites as "irregularly distributed." "irregularly disseminated," of "erratic occurrence," "proverbially erratic in distribution," "characterized by extreme irregularity in ... size and distribution of the essential minerals, and variety and proportion of the accessory minerals," and "spotty.&apos;"" Over many years, however, geologic techniques have been applied with increasing success to economic analysis of pegmatites. Investigations, chiefly since 1939, have shown that mineral distribution and structure of pegmatites are largely systematic and that detailed geologic study can be used to predict the size and shape of mineral deposits in pegmatites. Because the writers are most familiar with the pegmatites of the Black Hills, S. D., examples cited are from that area." Pegmatites mined in other dis- * All examples are described more cornpletely elsewhere.: tricts are similar to those in the Black Hills," and the techniques described here have been applied by geologists and engineers working in other districts. In actual practice few pegmatite mine operators attempt to make accurate estimates of grade and reserves in advance of mining. Many deposits are too small for mining except on a very small scale; few pegmatite mines have more than ten employes. Hence there is little systematic preparation for mining, and the capital outlay may be so small that only a general knowledge of reserves is necessary. Technical personnel are rarely employed by pegmatite mine operators to make such estimates. In the future, however, as capital outlay becomes larger, estimates of grade and reserves will have to be more accurate. Geologic Aspects of Determining Grade and Reserves Estimating grade and reserves requires that the type of pegmatite, the size and shape, and the internal structure be determined by detailed geologic mapping and careful mineralogic study. The wide variations in the texture and distribution of minerals within many pegmatite deposits make a thorough geologic study of this kind necessary before it is possible to decide what sampling methods should be used to determine mineral content or grade. Types of Pegmatites: The first step in economic appraisal of a pegmatite is to determine the min-eralogical and structural type. In general, pegmatites may be classified into two groups: 1) those in which component minerals are more or less evenly distributed throughout the entire body and show relatively minor variations in texture, and 2) those in which component minerals have been segregated into units with recognizable differences in texture, mineralogy. or both. Johnston" has classified these types of pegmatites as homogeneous and heterogeneous, respectively. Cameron et al.10 have used the terms ~inzoned and zoned for similar types. The difference between the homogeneous and heterogeneous types is of great commercial importance. Homogeneous pegmatites can seldom be mined where the products are concentrated by the hand methods now commonly used, but they have been mined in a few places where a milling process has

Jan 1, 1957

By Bengt Helmerson

A new tankhouse was started in January 1959 at the Copper Refinery of the Boliden Co., Skelleftehamn, Sweden. In early 1961 a semiautomatic machine for looping and straightening of starting sheets was introduced to substitute previous manual operations. The machine as well as consequent, racking and handling is described. Finally, economic benefits achieved and new constructions for the future are discussed. HISTORY Tankhouse operations at the Boliden Co. &apos;s Smelter in Skelleftehamn started in 1932 on a scale that since then has been gradually increasing. In order to rationalize the operations, a new tankhouse was erected. It went into production in January 1959 and was designed for a yearly production of 35,000 metric tons at a current density of 16 amps per sq ft. Already from the beginning, however, the tankhouse has been run with a current density of 21.5 amps per sq ft, corresponding to a maximum capacity of 50,000 tons a year. During the time of planning of the new tankhouse, due consideration was given to the possibilities of mechanizing the operations. New ideas could be and were actually tested on full or pilot plant scale in the old tankhouse. In that way we developed a system for the cathode handling including washing, weighing, and transportation. A system using forklift trucks in combination with trailers and overhead cranes has been developed for transportation and racking of anodes and also for handling of anode scrap. With respect to the electrolyte, circulation and temperature control are partly automatic. Special attention was paid to the production of starting sheets, which operation normally requires a great number of man hours, and it was made the object of a particular survey as to the best ways of straightening starting sheets, attaching loops to the sheets, and so forth. As a result, a machine was designed during 1957-58 and built in our own shops. After a period of tests, the new equipment was put in operation commercially on the 10th of April, 1961. Since this date the machine has produced about 2 million starting sheets without interruption and has been the only source of looped starting sheets for the tankhouse. GENERAL DESCRIPTION Fig. 1 shows all the major parts of the system. These parts are: slitting machine with feeding table (I), standard roller leveler, type Ungerer (2), tilting roller table (3), conveyors for sheets and suspension bars (4, 7), storage of suspension bars (51, punching and stitching machine (6), two lift-turn-tilt tables (8) for discharging the starting sheets, two rack conveyors (9) for sheet assemblies. Included are a hy-daulic pump station and panels for pneumatic and electric controls. SLITTING AND STRAIGHTENING The machine is fed by hand by a man sitting in front of the slitting-machine table, Fig. 2. This operator inserts one sheet at a time into the slitter. After being trimmed, the sheet is automatically conveyed to the following step of handling, straightening. The slitting machine cuts away about 8 mm of the upper and lower parts of the sheet (in relation to its original position in the stripper section) for two reasons. The first one is to give the machine sheets of uniform dimensions; the second one is a matter of quality. Normally the starting sheets as stripped have a thick edge at the bottom end. This part would collect anode slimes and might also cause short circuits when inserted in the cells without trimming. The straightener used is of German construction

Jan 1, 1967

By J. Murray Riddell, Grover J. Holt, Arthur E. Anderson

Out of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in Pow gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1940

By J. A. Bossert

"In 1957, the Department of Mines and Technical Surveys (now Energy, Mines and Resources Canada) issued their first certificate for a fire-resistant conveyor belt. The testing procedure used was a combination of those used in the U.S.A. and the U.K. Subsequently, certification was granted to fire resistant electric cables (1974), fire-resistant mine duct material (1976) and fire-resistant hydraulic fluids (1978).Until recently, the testing procedures were copied from either the U.S. or the U.K. However, since the founding of the new Canadian Standards Association (CSA) Steering Committee for Electrical/Mechanical Mine Safety in 1981, these requirements have come under the close scrutiny of new CSA technical committees who will attempt to adopt or change the existing procedures to meet Canadian needs. This paper outlines the existing test requirements and attempts to predict how they will appear after ""Canadianization"" by the CSA committees.IntroductionFires in underground mines have always been considered more serious than in other locations because of the confined space and limited atmosphere. A fire can make escape difficult or impossible if it is blocking all of the routes to the surface. Also, the products of combustion from an underground fire can asphyxiate anyone not having self-contained breathing apparatus.In an underground coal mine, the consequences of a fire can be even more serious because of the presence of methane and coal dust in the atmosphere (which can explode) and because the coal itself is combustible.For these reasons, the inspection authorities having jurisdiction over underground mine s in Canada are quite concerned about the flammability of any materials that are used in quantity in the underground environmentAs early as 1957, the Canadian Explosive Atmospheres Laboratory (CEAL) was asked to certify conveyor belting as fire-resistant. This is because many miles of this material are used in underground mines in Canada and, as it generally travels through the mine, it is a perfect vehicle for spreading a fire."

Jan 1, 1982

By J. Murray Riddell, Arthur E. Anderson, Grover J. Holt

Out of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in Pow gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1940

By J. Murray Riddell, Arthur E. Anderson, Grover J. Holt

OUT of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the seasor1 of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in low gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1938

By R. W. Carn, D. Vincent

During the next 15 years, US coal production is expected to double, with the increased production evenly divided between the East and the West. Along with greater production, coal export markets should increase dramatically from East, West, and Gulf Coast ports. The annual overseas export capacity of US coal-loading terminals is expected to rise from 147.1 Mt (162.1 million st) in 1981 to a minimum of 278.1 Mt (306.6 million st) in 1985, according to the US Maritime Administration. Increased coal production and use will lead to more development of import and export terminals, a vital link in the coal transportation chain. With continually escalating capital costs and the competitive markets that the terminals will serve, a well designed and efficient terminal is necessary. This article begins a two-part series that presents concepts presently used in coal export terminal design. Part I looks at site selection factors and equipment needs, while Part II will examine environmental considerations in building a terminal as well as typical capital and operating costs. The world is nearing the end of the oil era. In a few years oil will not be available to sustain the growth rate and increasing standard of living we have known in our lifetime. The big question is what energy era are we moving into? With the decline of readily available oil reserves and rapidly increasing prices, many countries are trying to switch to alternate energy forms. While intensive efforts to find new oil reserves continue, alternate energy sources such as natural gas, coal, synthetic fuels, nuclear, hydroelectric, solar, and wind power are being developed. Recent indications are that coal is expected to bridge the energy gap over the next 25-30 years until the technology and economics of the alternate energy forms reach satisfactory levels. Use of coal for energy is receiving strong attention due to its long-term availability (200-300 years minimum), relative ease of development, and its low cost per unit of power produced. By the year 2000, it is expected that 25% of world energy supply will be met by direct coal combustion and possibly another 5-10% by synthetic fuel from coal. Coal&apos;s expanding share in the world energy market, along with an increase in coking coal requirements, will result in a large increase in the world&apos;s seaborne coal trade. Recent statistics and projections for the future are shown in Table 1. This phenomenal development rate includes increases in both coking and thermal coal requirements. Because of the rapid increase of seaborne coal trade during the last 10 years and the even greater projected increase of trade to 2000, various sectors of the coal industry are faced with enormous technical challenges and huge investments in equipment, land, transportation systems, and port facilities. Very large bulk terminals are under development throughout the world. Latest surveys indicate that there are about 30 new coal export and import terminals under consideration and at least 30 existing terminals have expansion programs planned or underway. With the high cost of borrowed capital and rapid inflation rates there is great emphasis on new planning and design techniques to minimize capital and operating costs of coal transportation systems. Terminals A total coal supply system can be considered to consist of one or more mines; a train, barge, truck, or other haulage system; an export terminal; a fleet of bulk carriers; a receiving terminal; and possibly, local inland distribution networks that include barges and railways. Terminals, though only a small link in the total transportation system, play a key role in overall system efficiency. At ports or inland distribution centers, terminals act as transportation links bringing trains, ships, barges, or trucks together for cargo transfer and temporary storage. A well-designed terminal can provide maximum independence between two modes of transportation and optimum freedom for intermodal interference. A terminal acts as a buffer between the two transportation modes by providing sufficient storage capacity so a ship need not wait for its cargo on, for example, a train-by-train basis, but can load immediately from the ready stock. Similarly, a train need not wait for a ship to unload its contents but can dump immediately into storage. A terminal also can be used to properly mix various types of coal to satisfy a buyer&apos;s requirements. Consider the relative value of various production and transport segments for a typical steam coal

Jan 6, 1983

By Leah L. Naugle, H. G. Landau, H. H. Lowry

EVIDENCE has been accumulating in recent years, in part from the work of the Coal Research Laboratory, that coals belong to a family of natural polymers and that even in complex reactions the differences between coals are quantitative and not qualitative. This point of view leads to the expectation that if a series of coals were subjected to a closely controlled set of experimental conditions the results obtained should be related to the chemical analyses of the individual coals. The data accumulated over the past 10 years by the Bureau of Mines in its "Survey of Coke-, Gas-, and By-Product-Making Properties of American Coals," in what has come to be recognized as the Bureau of Mines-American Gas Association (BM-AGA) carbonization assay test,1-12 offer an unusual opportunity to check this conclusion. The present paper reports an analysis of the data on the first go coals and coal blends-including coals numbered I to 55b, inclusive -which have been carbonized according to a standard procedure at intervals of 100°C. from 500° to 1100° in either or both 13 or I8-in. cylindrical retorts." In Table I are given the name of the seam from which the sample was obtained, the analytical data used, and the reference to the original publication of the Bureau of Mines. The coals range in fixed carbon from 46.2 to 79.0 per cent, in volatile matter from 15.4 to 41.3 per cent, in ash; from 2.1 to 15.9 per cent, in moisture from o.8 to 19.7 per cent, and in total sulphur from 0.40 to 4.44 per cent; therefore the entire gamut of bituminous coals is represented. The petrographic nature of the individual coals is not considered in the following analysis, although both "normal" bright coals and splint coals are included in the samples studied. For information on the petrography of the coals and for further information characterizing the coals the original papers should be consulted. Although the coals that are included extend over the whole range of bituminous coals, they do not cover this range entirely adequately. In particular, only 13 of the go coals have moisture contents greater than 3 per cent. This concentration at low moisture values means that the effect of moisture, which is an important factor, cannot be determined with as much certainty as would be desirable. All the coals were not tested at every temperature and in both retort sizes. Only the first 30 coals were tested at 1100°, and only about 50 at the other temperatures, except at 900°, where nearly all of them were included. In the accompanying tables the actual number of observations entering into each correlation is given. In this study equations are given for calculating analyses, yields, and properties of coke and by-products from the coal analyses. To decide whether these equations are satisfactory it is necessary to know the accuracy with which these quantities were measured in the assay tests.

Jan 1, 1941

Reason Analysis of Impurity Containing and Technology Discussion of Quality Improvement for Low-Quality Iron Concentrate

Sep 13, 2010

By S. -H. Chang, C. -I. Lee, Y. -K. Lee

Based on results from triaxial compressive tests, an experimental damage model to simulate post-peak behaviours as well as nonlinear behaviours before peak strength was developed. In order to consider pre-peak behaviours, variations of elastic constants at each damage level were regressed by functions of confining pressure. In addition, post-peak behaviours were simulated successfully by using Hoek-Brown constants. As results, the experimental model could predict nonlinear behaviours, peak strengths and stiffness changes observed in experiments. Basé sur des résultats des essais compressifs à trois axes, un modèle expérimental de dommages pour simuler des comportements de poteau-crête aussi bien que des comportements non-linéaires avant la force maximale a été développé. Afin de considérer des comportements de pré-crête, des variations des constantes élastiques à chaque niveau de dommages ont été régressées par des fonctions de pression d&apos;emprisonnement. En outre, des comportements de poteau-crête ont été simulés avec succès en employant des constantes de Hoek-Brunes. Comme résultat, le modèle expérimental a pu prévoir des comportements non-linéaires, des forces maximales et des changements de riidité observés dans les expériences. Auf Basis der Ergebnisse des dreiaxialen Drucktests wurde das experimentelle Schadensmodell, das sowohl das nicht-lineare Verhalten vor der maximalen Stärke als auch das Verhalten nach der maximalen Stärke simulieren kann, entwickelt. Um das Verhalten vor der maximalen Stärke zu berücksichtigen, wurden die Veränderungen der elastischen Konstante bei dem jeweiligen Schadensniveau durch die Funktionen des begrenzten Drucks zurückgegangen. Außerdem wurde das Verhalten nach der maximalen Stärke unter Benutzung von Hoek-Brown Konstanten erfolgreich simuliert. Schließlich konnte das experimentelle Modell das nicht-lineare Verhalten, die maximale Stärke und die Veränderungen bezüglich der Steifigkeit während der Experimente voraussehen.

Jan 1, 2003

The quantity, quality and detail of project information increases as project development moves from initial scoping level studies, to pre-feasibility and option studies, then definitive feasibility study and basic engineering stages. Data accumulates from metallurgical and vendor testing from various ore types and composites carried out to assess physical characteristics and processing responses of the ore. Over-simplification or assumptions about the orebody for flow sheet development can result in using æaverageÆ information for design. Use of averages of data can have adverse implications on sizing of plant and equipment and consequently on definitive study cost estimates and detailed engineering. In practice, the treatment plant workforce is faced with managing a non-homogeneous or non-average orebody in a variable operating environment that is not always predictable. This paper presents views on how to use the data generated from testwork in project development and for process and plant design. Examples of process design risk or operating risk are presented. Although this topic is applicable to the broad range of process design decision making in the minerals industry, this discussion references comminution, flotation and extraction processes for gold and base metal ores.

Jan 1, 2004

By V. T. McLemore

Deposits of rare earth elements (REE) are found in NM, but they have not been important exploration targets in past years because demand has been met elsewhere. However, with the projected increase in demand and potential lack of available production from China, the New Mexico deposits are being re-examined for their potential. REE-Th-U veins are found in the Gallinas, Caballo, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Past production of bastnaesite has come from the Gallinas Mountains. Carbonatites are found in the Lemitar and Chupadera Mountains, Laughlin Peak-Chico Hills, Lobo Hill, and Monte Largo (Sandia Mountains). Although carbonatites have not been found in the Gallinas Mountains, they are suspected to occur in the subsurface based upon mineralogy/alteration. Disseminated Y-Zr deposits in syenite are found at Pajarito Mountain, Mescalero Apache Indian Reservation near Ruidoso. In 1990, Molycorp, Inc. reported historic resources of 2.7 million short tons grading 0.18% Y2O3 and 1.2% ZrO2 as disseminated eudialyte. Two additional deposit types have potential for REE in New Mexico: Cretaceous heavy mineral, beach-placer sandstone deposits and pegmatites. Exploration is ongoing in the Lemitar, Gallinas, and Cornudas Mountains.

Jan 1, 2012

By L. Nahai

Overall mineral industry productive activity in Europe increased in 1965, following general upward trends in gross national product and total industrial production4 recorded. The gross national product of non-Communist Europe in market prices in 1965 was estimated at $572 billion and that of Communist Europe at $409 billion. However, the extractive sectors of the mineral industries generally did not fare as well as the processing sectors. In fact, a number of countries recorded lower production levels in this sector in 1965 than in 1964 and most countries had a lower growth rate in extractive industry output than in overall industrial output. Among the non-Communist nations of Europe, a general decline in coal production and lower levels of iron ore output in France, West Germany, and Luxembourg contributed significantly to the smaller growth rates or declines in extractive indexes. Where higher indexes were registered, this generally resulted from the performance of the petroleum and natural gas industry; exceptions were Greece, Norway, and Sweden. The decline recorded for Czechoslovakia was attributable entirely to poorer performance by that nation&apos;s coal industry.

Jan 1, 1967

By Laurence Delisle, Aaron Finger

THE alloys formed by the addition of nickel to iron by convelltional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.? owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect could be obtained in alloys of iron and nickel prepared by powder metallurgy technique. PROCEDURE Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, 0.001 5 ; lead, 0.035; tin, 0.025 ; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A representative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 3 2 5-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the surfaces of the particles. The reduced powders, slightly caked, were ground in a mortar and screened again through a 325- mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hydraulic presses. The pellets were compacted in a cylindrical die, ½ in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specifed for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

DR. BANOWSKY: Thank you very much. That was the shortest introduction that I have had lately, and I didn&apos;t have time to get my coat on. But I appreciated it, and I&apos;m delighted to be here with an industry with which 1 feel strong affinity. At the University of Oklahoma we have an energy history. We are a little more currently involved in oil and gas, and those of you who know the history of our state would be aware we have an early coal development back really before the turn of the century in the southeast part of our state what we call Little Dixie. How many of you have spent anytime in Oklahoma or are from the state of Oklahoma? I&apos;m not going to ask how many are from OSU or the University of Colorado. We did send you a football coach here from Oklahoma, and 1 see you have exchanged him. Several of you were only interested in the lobby in asking about our football team this year. 1 would like to go somewhere where we can talk about something besides football. I&apos;m just trying to build a University that our football team can be proud of. We&apos;re going to be strong again. 1 can assure you. We&apos;ve got the best football team money can buy. It&apos;s not quite as bad as the college president who called the coach in and said, "Coach we&apos;re in trouble, you&apos;re losing games and the alumni is very unhappy." "What can we do?" the president asked. The coach said, "Well the football team is flunking the admissions test. We can&apos;t get them in with the standard achievement and SAT tests." The president said, "What can we do?" The coach said, "Well the coaching staff has substituted for the American College Test the simple fill in the blank questionnaire." The president said, "Let&apos;s use it. We have got to get the team in." The first question was, Old MacDonald had a (-). And a couple of the big tackles were taking it and one of them said, "Hey, what did Old MacDonald have?" His friend said, "Stupid, Old MacDonald had a farm." "Well how do you spell farm?" He said, "Stupid, e i e i 0." Now the gentleman who met me at the registration line from Lakewood, Colorado, was asking me about one of our great big tackles; and he is doing well. We call him Doctor Death; he is also a wrestler and that gentleman said, "1 don&apos;t know how bright he is." 1 said, "He is bright enough for our academic tutoring that he is going to get through all right." So I&apos;m delighted to see you and be here with my very dear friend, Carl Terzian. Carl and 1 were in Los Angeles together for 10 or 12 years when I was president of Pepperdine University. He and I are exactly the same age. Born in 1935 and 1 a month or two later in 1936. Fewer children were born in that period than in any other period of time in this century. For those of you who remember anything about that period, you will know why no one was having babies during that period. But Carl called and said, "Bill do you know where Vail, Colorado is?" Well when you live in Oklahoma, you learn where Colorado is in a hurry. 1 not only know this beautiful area, but have made too much of an investment here at a place called Beaver Creek. The real estate is cheap over there. 1 play regularly in the Gerald Ford Invitational Golf Tournament here. Hope you will visit Beaver Creek. It&apos;s just 10- 12 miles to the west. The sight of the 1976 winter olympics until the people of Colorado voted them out. And now Vail Associates and I are good Oklahoma families. Bass family, Harry Bass of course, many of you know this story, who is chairman of the Board of Vail Associates, is making quite an investment in that year-round resort area. Beautiful golf course now. You can come out and afford the green&apos;s fee and beautiful, beauti-

Jan 1, 1982

By R. G. Treuting

Germanium single crystals strained in tension at 600°C slip on the {Ill} plane and, macroscopically at least, in the <110> direction. Deformation is in homogeneous: various localized rotations are observed, as is a banding consistent with secondary slip banding. The structure after deformation is polygonized with a domain size of about 2x1O-3 cm. In relaxation tests, an incubation period prior to flow is observed, of duration inversely related to temperature and applied stress. Under continuous loading, there is a sharp first yield point. A critical resolved shear stress therefore must be cited with respect both to temperature and to rate of loading. At 600°C, when loading proceeds at 2900 psi per min, it is 1310 psi. The yield point phenomenon is suggestive of Cottrell&apos;s solute atom atmosphere theory and five points of qualitative agreement with this theory are found. PLASTICITY of germanium at elevated temperatures has been reported by Gallagher,&apos; who ascribed it to slip on {Ill) planes and described some associated effects. Preliminary experiments with single crystals of silicon and germanium loaded as simple beams confirmed {ill) as the slip plane of both materials.V his was demonstrated by the standard technique employing traces on two surfaces of known angle on a deformed crystal of known orientation.3 These experiments did not fix the slip direction, since more than one glide system operated. Uniaxial tensile straining is preferred for this purpose in order to restrict slip to one predominant system and to provide an unequivocal determination of the orientation change with respect to the stress axis. Experimental Method Specimens were diamond-sawed from germanium crystals containing about 5x10-5 wt pct Sb prepared by the zone-leveling process described by Pfann and Olsen;4 these specimens measured about 81/2 in. long, 0.20 in. wide, and were of various thicknesses from 0.035 to 0.060 in. Prior to testing, a specimen was coated over 1 in. or more of length at each end with Apiezon wax, chemically polished (in a solution of 15 ml HF, 25 ml HNO,, 15 ml CH3COOH, and 3 to 4 drops Br2), and dewaxed in warm xylene. A brief re-etching after scribing through a complete wax coating with vernier dividers provided gage marks at 0.200 in. intervals on the polished surface. A specimen with grips soft soldered to the ends was passed through the furnace tube and the grips pinned to the tensile machine in series with a stress gage. The Schopper testing machine is best described by reference to the illustration on p. 107 of Schmid and Boas5 and is operated with the pendulum arm locked, fixing the upper head. Load is applied through the screw-driven lower head, manually or by reduced speed motor. The furnace is 21/2 in. long surrounding a 4x7/16 in. ID quartz tube and was positioned about the specimen to permit free motion. The inert or reducing atmosphere required was sufficiently provided by a flow of helium introduced at the center of the furnace tube, with the tube ends loosely plugged with asbestos paper. Surface corrosion was slight. The stress gage employs a Be-Cu strip with SR-4 units incorporated in a simple bridge network with provision for balancing and calibrating. The bridge output on loading is fed through a Leeds and North-rup dc amplifier to a Speedomax 10 mv recorder, and calibration is obtained by dead loading. Experiments of two types have been conducted. Most have been in relaxation at constant elongation. One stress-strain curve has been taken with the machine continuously driven. Following extension of a specimen, Laue X-ray photographs were taken to obtain the orientation change between deformed and undeformed regions, recorded on a single film by translating the specimen in a plane normal to the beam between exposures. Sequences of such multiple exposures were made on some specimens to include the entire orientation range on one film. Slip Direction To obtain a maximum orientation change with a single slip system, crystals of very closely <110> axial orientation were used. The classic determination of slip direction rests on establishing that direc-

Jan 1, 1956