Search Documents

By J. D. Davis

THIS REPORT gives results of an investi¬gation of the carbonizing properties of coals from Pittsburgh bed, Jamison No. 9 mine, Marion County, W. Va., and from Upper Freeport bed, Bull Run No. 1 mine, Preston County, W. Va. The study included Bureau of Mines-American Gas Association tests at 800° and 900° C. and various chemical and physical tests designed to evaluate the plastic, expanding, and agglutinating properties of coal. A blend of each coal was carbonized in the 500-pound slot oven. The carbonization sample of Pittsburgh coal contained 2.7 percent moisture, 35.8 percent volatile matter, 54.4 percent fixed carbon, 7.1 percent ash, and 0.9 percent sulfur. It contained 60.9 percent fixed carbon on the dry, mineral-matter-free basis and had a heating value of 14,780 B. t. u. per pound on the moist, mineral-matter-free basis. It therefore ranks as high-volatile A bituminous and was blended with low-volatile Pocahontas No. 3 coal. Upper Freeport coal contained 2.8 percent moisture, 27.7 percent volatile matter, 60.9 percent fixed carbon, 8.6 percent ash, and 1.0 percent sulfur, as carbonized. It contained 69.5 percent fixed carbon on the dry, mineral-matter-free basis and therefore ranks as medium-volatile bituminous. It was blended with high-volatile A Pittsburgh coal from Allegheny County Pa.

Jan 1, 1952

By N. V. Hansell

l. INTRODUCTION. THE last few years have shown an increasing interest in the subject of beneficiating iron-ores -in all iron-producing countries. In the United States, this movement has been slower than in certain parts of Europe, for the obvious reason that the abundance and relative cheapness of the Lake Superior iron ores has hindered the development of enterprises for the preparation of low-grade ores. Gradually, however, conditions have changed. The world's consumption of iron is increasing enormously. Being in 1900 about 40,000,000 tons, in 1910 ii was already 60,000000; and there is no reason to doubt that for the near future the increase in iron-consumption will continue at the same rapid rate, especially with, the development of China, certain parts of Africa, and other regions which have hardly been touched as yet by modern industrialism. It is. therefore, not surprising that apprehension is felt that the known available iron-ore resources of the world are gradually being depleted. Signs of this feeling are the recent investigation, under the direction of the U. S. Geological Survey, of the iron-ore resources of the United States, and the estimate presented to the last International Geological Congress, at Stockholm, Sweden, of the iron-ore resources of the world. These investigations have emphasized the fact that the known high-grade ore-deposits are limited in extent, and will, at a not distant future, be exhausted, compelling the iron industry to depend for raw material on the enormous deposits of low-grade ores which are distributed over almost all the world. The discovery of new deposits of high-grade ore, in countries not yet thoroughly explored, will not materially change this prospect. Of course, the part which such new deposits will play in the future cannot be forecast. The difficulty and cost of transportation will probably exclude many of them from use at the present centers of the iron industry.

May 1, 1912

By I D. Gregson, A Gandhe, A S. Garcia, K M. MacAndrew

"Falls of ground still cause around one-third of all underground mining fatalities. The recent introduction of mechanised room and pillar working into Indian coalmines is an example of the application of new design by measurement and safety monitoring strategies, which can be used to reduce falls of ground risks in mines.Rock Mechanics Technology, now part of Golder Associates UK Ltd (Golder), is providing rock bolt support and pillar design services to the mines using a design by measurement approach. This involves in situ monitoring to confirm support and pillar designs and pillar extraction sequences.Site examples are given of the support designs determined and the monitoring programs undertaken for both design and safety.Routine safety monitoring of roof movement using telltales is also described. A new auto warning telltale has been developed specifically to warn of imminent caving as pillars are extracted.The approach used by Golder has played a major role in ensuring the success of these projects. As a consequence, mechanised room and pillar working is now firmly established in India, and wider application is planned to help meet future demand for coal.The experience confirms that the design by measurement method for this application has important advantages over conventional design approaches using analytical or empirical methods. Firstly, it measures the design performance or outcome rather than trying to calculate or predict it. Secondly, it provides the opportunity for the design to be adjusted to obtain the optimum outcome. Thirdly, it can do this at a local level, so that the support design can be matched to changing conditions to give the most cost-effective design. Finally, it incorporates long-term monitoring of support performance, again at a local level, so that subsequent change can be identified to enable corrective measures to be implemented in a timely manner and to ensure that ground control safety is maintained.CITATION:MacAndrew, K M, Garcia, A S, Gregson, I D and Gandhe, A, 2014. Application of design by measurement for support and pillar design in mechanised room and pillar coal mining in India, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By Stephen Mansfield

Analysing how accurately a blast design is implemented is one of the cornerstones of a successful operation, and critical for mine optimisation. This paper presents a concept that involves the collection and analysis of data for the five stages through which a blast transitions, from budget through to implementation.

Feb 1, 2020

By K. L. Bainbridge

This report describes the results of a study to determine which types of, and to what extent, mining wastes can contaminate groundwater through leaching of acid-forming or potentially toxic constituents. The primary focus of this study was on coal mining wastes, especially overburden spoils and preparation plant refuse. In addition, the potential for contamination by leachates from clean coal stockpiles was also examined. The study approach included investigation of (a) the amounts and geographic locations of mining wastes in the United States; (b) the chemical character of mining wastes, especially with regard to potentially acid-firming or toxic constituents; and (c) the extent to which acid and/or toxic components are leached from mining wastes by rainwater. To evaluate the leachability of coal wastes, a laboratory waste leaching method was developed during this study to specifically simulate the leaching process over a long-term. Waste samples collected during this study were also leached by the EPA extraction procedure and ASTM waste leaching method. Results of the three leach test methods were compared to evaluate their relative capabilities to predict the leachability of mining wastes.

Jan 1, 1980

By Gerald T. Homce

Accidental contact of overhead electrical power lines by mobile equipment is a leading cause of occupational fatalities in the United States, accounting for 20% of on-the-job electrocutions. Overhead electrical power line proximity warning devices (PWDs) are intended to warn personnel if mobile equipment moves within some preselected minimum distance of an energized overhead electrical power line. Two commercially available PWDs were tested at the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). The objective of the tests was to document performance capabilities and limitations for these PWDs by identifying factors that can influence their operation. The two PWDs evaluated in this research are the SIGALARM Model 210 marketed by Allied Safety Systems, LLC, and the ASE Model 2100 from Allied Safety Engineering. Both of these devices operate by measuring the electric field present around energized power lines. The PWDs were installed on a government-owned 22-st (20-mt) rough terrain crane. A purpose-built test site used for this research at PRL allowed operation of the crane near a variety of power line configurations operating at up to 25 kV. Most of the tests involved positioning the crane adjacent to one or more overhead power lines, adjusting sensitivities of the PWDs to alarm when the crane boom was approximately 20 ft (6.1 m) from the power lines, swinging the crane boom toward the lines under a wide variety of test conditions, and finally, for each unique set of test conditions, documenting the deviation from 20 ft (6.1 m) for actual alarm activation. Test results show that several factors can adversely affect PWD performance. PWD alarm accuracy generally deteriorated when operating with a boom position significantly different than that used for the device?s last sensitivity adjustment. Another factor that can affect PWD performance is configuration of the overhead power line(s) involved. Accuracy of alarm activa­tion distances was best for simple single-circuit installations, but degraded for multiple circuits on the same poles. This degradation was slightly greater for installations with different voltage levels and/or a combination of vertical and horizontal conductor arrangements. Performance also degraded for crane operation between two intersecting power line installations, especially for intersecting lines at different voltages. An additional aspect of power line configuration shown to influence PWD accuracy was phase sequence on the power line circuit(s). Specific phase con­ductor arrangements and combinations, particularly in multiple circuit installations, resulted in either improved or degraded accuracy.

Jan 1, 2008

By George W. Land

For the year 1985, the U.S. coal industry produced 881 million tons of bituminous coal and lignite. Domestic consumption amounted to 814 million tons. The electric utilities consumed 689 million tons, almost 85 percent of total consumption, over 78 percent of production. In May, 1986, the NCA forecast that with moderate growth rate averaging 1.9% per year from 1985 through the year 2000, production could reach 1,176 billion tons and domestic consumption 1079 billion. The estimate for electric utilities indicate 924 million tons for the year of 2000, about the same percentage of production and consumption as now experienced. Before we consider the main topic of this paper, the cost of using high sulfur coal, let us examine the coal use patterns of the last 25 years, the changes in those patterns and consider the reasons for those changes. Table I shows those changes.

Jan 1, 1986

By Kevin J. Ma, John Stankus, Dakota Faulkner

"Expandable rock bolts are widely used in hard rock mines as an efficient ground control product. However, capacity and service life can be significantly reduced if the metallic body is subjected to corrosion. In some hard rock mines in the U.S., highly corrosive ground conditions exist, and it has been reported that inflatable rock bolts have corroded within a few months after installation. To provide mining industry a cost-effective inflatable bolt and combat the corrosion issues, Jennmar Corporation, Inc., and its subsidiary Keystone Mining Services, LLC (KMS), analyzed corroded bolt samples, identified root causes, evaluated properties of various coating materials, and developed a new inflatable rock bolt, Python M3TM, that is protected with an innovative PyFlexU2TM coating. The new generation Python M3 features improved steel chemistry for reliable performance, modified profile for better inflation, and surface preparation and coating application. The PyFlexU2 is impervious to liquid and air, durable, and UV resistant. With a flexible adhesive, and highly corrosion-resistant undercoating, and a very hard sacrificial surface coating, the PyFlexU2 coating system provides the Python M3 superior protection against chemical corrosion and physical scratch damage. The under-coating has exceptional flexibility and adhesion to prevent coating micro-cracks or fractures after bolt inflation and possesses excellent corrosion resistance to acids (pH <3), alkalis (pH >11), fuels, and salt solvents. The corrosion and scratch resistant PyFlexU2 coating offers very effective bolt protection for extra longevity in highly corrosive environments. The Python M3 coated with PyFlexU2 has been tested in the most challenging conditions, including laboratory corrosion tests in extreme acidic and basic solvents, rock slurry, and borehole scratch insertion tests. With demonstrated corrosion and scratch resistance, the product has been greatly welcomed by hard rock mines in the West and is currently installed in large scale. This paper identifies the root causes of the bolt corrosion, discusses the analysis process, and details laboratory and underground tests carried out on the Python M3 coated with PyFlexU2. The Python M3TM and PyFlexU2TM are subjects covered by pending U.S. Patent Applications assigned to FCI Holdings Delaware, LLC."

Jan 1, 2017

By Peter N. Gabby

A mineral purvey of 40,000 acres of the 42,213-acre Little Humboldt River Wilderness Study Area was conducted by the U.S. Bureau of Mines in 1985 at the request of the U.S. Bureau of Land Management. There are no identified mineral resources but anomalous gold, silver, mercury, and arsenic concentrations were found. The study area is located in Elko County, NV, in the Owyhee Upland geomorphic subprovince. It is underlain by mid- to late-Miocene-age rhyolite, basalt, tuff, vitric ash, and tuffaceous siltstone. On the south side and partly within the study area, a mining company recently (January 1986) located 125 contiguous claims over an area of hydrothermally-altered volcanic rocks that have anomalous surface concentrations of gold, mercury, arsenic, and silver. Anomalous gold-silver concentrations in altered rocks were encountered at several other widely scattered localities in the study area. These elevated metal concentrations and associated hydrothermal alteration indicate gold resources may be present in the study area. A 20-ft-thick bed of diatomaceous earth, which contains 60 to 85 percent diatoms, crops out 0.3 mi north of the study area. Elsewhere, three samples of altered volcanic tuff taken within the study area contain from 46 to 70 percent zeolite (clinoptilolite). The diatomaceous earth and zeolite sampled are not of sufficient quality to compete with materials presently being marketed. There has been no mineral production from the study area, but a caved adit, about 25 ft long, and six prospect pits were found.

Jan 1, 1987

By LUIS ALBERTO TORRES-CRUZ

The assessment of liquefaction vulnerability is crucial to understanding the potential consequences of a tailings dam failure. The “Plewes method” is a relatively well-known and simple screening method to assess liquefaction potential based on results of cone penetration testing (CPT) which may be complemented with laboratory testing. The objective of the current work is to emphasise the screening nature of the method and its uncertainties when applied in tailings deposits. Specifically, the paper highlights the difficulties in assessing the intrinsic uncertainty of the method and the additional uncertainty that results from variations of the slope of the critical state line (λ10) along the depth of the CPT sounding. The results of the method are too uncertain for detailed characterisation of tailings even when a relatively low intrinsic uncertainty is assumed. However, the method characterises weaker soils with lower uncertainty (although still too high for detailed characterisation) than stronger soils. The uncertainty of the method is negatively affected by the relatively low λ10 values that are typical of nonplastic tailings. It is suggested that the results of the method should be presented in scatter plots in which the spread of the data is consistent with the uncertainty of the method.

Jan 28, 2021

By Gil Bourcier

A process has been developed for detoxifying spent potliner (SPL) in which the SPL is blended with limestone and an anti-agglomeration agent and thermally treated in a rotary kiln. The process has been proven and a commercial plant is in operation at Gum Springs, Arkansas. The treated by-product material has been delisted by the U.S. EPA and is now a potential raw material for many commercial applications. Finding uses for a non-hazardous material has many advantages over finding uses for a hazardous material like SPL. Complete usage of the by-product will complete the life cycle and eliminate any landfilling of non-hazardous SPL by-products or residues. Being non-hazardous and containing compounds used in the ceramic and numerous other industries assures many potential uses for the spent potliner by-product.

Jan 1, 1994

By Brian Lewis, Reinhold Daykin Schnell

Blasting specifications and guidelines are very important aspects of detailed project specifications covering any scope of work (SOW) that involves explosives and blasting procedures. A lot of larger construction or tunneling projects require some degree of project specifications for the entire scope of work on such project, including blasting specifications. It is important that all blasting specifications effectively and accurately address all explosives and blasting concerns associated with the SOW for such project. This includes safety and security, required personnel and their associated responsibilities, procedures and applications involving explosives, blast design and planning, blast monitoring and reporting, quality assurance and quality control, and local, state, and federal regulations and limitations. With the of wide range of information required in blasting and overall project specifications along with the risks associated with work involving explosives, it is also important to ensure qualified personnel are involved in interpreting or compiling and approving any blasting specifications and guidelines. The purpose of the following paper is to explore and present the basic information, as summarized above, that should be included and considered in the creation of detailed blasting specifications and guidelines. Detailed information is presented in specific relation to a potential bid package that would be compiled for a construction or tunneling project requiring protective or high-profile blasting.

Feb 6, 2023

By D. R. Hembree

This paper discusses the mineralogy and metallurgy of the Kuroko-style volcanogenic massive sulfide ores mined at Formosa Exploration Inc. I s Silver Butte Mine located in southwest Oregon. The principle ore type is pyrite + chalcopyrite + sphalerite, while subsidiary pyrite + bornite + sphalerite ore is also mined. The two styles of mineralization have distinctly different metallurgical behaviors and must be treated separately. Selective flotation methods are used to produce copper and zinc concentrates from the first ore type, while bulk concentrates are produced from the bornite ore. Careful mine planning and coordination between the mine and mill are utilized to achieve optimal recoveries.

Jan 1, 1993

By A. C. Lordi

Present industrial plant design is influenced by motivators beyond the usual powerful one, creativity, on which Consultants thrive. The respected, although annoying, ever-present Return on Invested Capital becomes even more significant with anticipated escalation. Government regulations are having an increasing influence as air and water protection, sound and electrical safety requirements must be met And more recently, the increasing cost and uncertain availability of energy sources are having a revolutionary affect on plant design. More than ever before, the Consulting Engineer is faced with requirements and restrictions which tax even the most original thinkers -- and the result is good. This paper includes a brief review of recent trends in Cement Plant Engineering Design.

Jan 1, 1975

By I H. Jung, W O. Choe

Gallium (Ga)-containing compounds such as Gallium Arsenide (GaAs) and Gallium Nitride (GaN) are widely used in electronic devices due to their superior electro-optical properties and their usages increase rapidly. For the sustainable supply of Ga to electronic industry, therefore, the recycling of Gallium becomes essential. Pyrometallurgical Ga recycling process involves the complex chemical reactions between slag, matte, liquid metal, gas, refractories, etc. Therefore, the accurate thermodynamic information and phase diagram data for the oxide system containing Ga2O3 is important. In the present study, new phase diagram experiments for binary SiO2-Ga2O3 and ternary CaO-SiO2-Ga2O3 system are carried out using Differential Thermal Analysis (DTA) and quenching experiments followed by Electron Probe Micro-Analyser (EPMA) and X-Ray Diffraction (XRD) phase analysis. Based on new phase diagram data and available literature data, the thermodynamic modelling of the entire CaO-SiO2-Ga2O3 system is performed for the first time.

Jun 19, 2024

By Walter L. Fisher

The public interest in the Alaskan situation is such that, with the consent of the President, I have concluded, at the request of the American Mining Congress, to make at this time a candid, if somewhat informal, expression of the views I have formed as Secretary of the Interior, under whose official supervision much of the administration of the Territory is now placed. Pressure of other matters imperatively requiring attention has prevented their presentation in as precise and comprehensive a form as I had hoped. The absence of the President from Washington has also prevented the submission to him of what I have prepared. I wish to say, however, that no one is more earnest than he in the desire to see a policy of prompt and wise development inaugurated in Alaska, and that the general policy contained in this address has been discussed with him, meets his approval, and will have his support. I have recently returned from an altogether too brief but nevertheless a most interesting and profitable visit to those portions of Alaska that are more immediately involved in the questions now under public consideration. Favored by extraordinary weather and the cooperation of steamship and railroad lines and the assistance of all of the governmental agencies, including the Revenue-Cutter Service, I visited every port in Alaska that seems likely in the near future to become an important entrance to the country. I examined all of the harbor and town sites which for this purpose have attracted any considerable public attention. I traversed the entire length of each of the three railroads that have been constructed in the Terri.tory and made a short trip from White Horse down the upper Yukon. Both before and during the journey I examined a mass of books, records,' and papers relating to the country and its resources. I had conferences with official committees representing the principal communities I visited and with numerous individuals, residents both of the coast and of the interi.or, and conferred with engineers, miners, prospectors, railroad officials, business and professional men.

Jan 1, 1911

By Henning R. Norbom

Lime has been produced for many centuries. The simple pot kiln was one of the first devices used in this process. It was constructed of stone often on the side of a hill to reduce construction efforts and provide easy access to the top for feeding of limestone. It was fired from below with wood and coal. The pot kiln was very small and operated on the batch principle. The kiln being cooled between each batch, the fuel consumption was horrendous. The lime quality was poor with perhaps only one half of a batch being lime of suitable quality. Of the remaining half one part would be over burned and another part underburned. For centuries the lime burning technique was improved at a barely recognizable rate. One of the first major steps forward was the introduction of the continuous process vertical lime kiln. Although at first crudely constructed, the kiln had a refractory lining. It was charged with alternate layers of limestone and solid fuel usually in the form of coke. Continuous mode of operation, larger unit size and better heat distribution resulted in greatly improved fuel economy. However, quality of lime produced still left much to be desired. One problem was contamination by ashes from solid fuel.

Jan 1, 1978

By Marketa D. Evans

The mining industry has a significant opportunity to capitalize on its past learnings in order to build better social relationships. The industry?s relationship with society is both critical and under pressure. Rising levels of public opposition and social conflict are already having material impacts on operations around the world. Industry has an opportunity to shape the future direction of this social engagement, build public trust and proactively respond to a material risk to operations, but first it needs to better understand the nature of the challenges and the urgency of addressing them.

Aug 1, 2013

By Max Friedemann, Alexandros Bousdekis, Anna Gustafson, Helmut Mischo, Håkan Schunnesson

Many devices used in mining are not monitored by sensors or do not have their own intelligence. By retrofitting sensors and real-time data processing, machines can be integrated into an existing digital infrastructure. Within the project Mine.io funded by the European Union a Sandvik DE110 exploration drill rig is being digitized using various AI algorithms at research and education Mine “Forschungs- und Lehrbergwerk Reiche Zeche (FLB)” of TU Freiberg. The aim is to increase the productivity of drilling with real-time evaluation of the current rock to be drilled and the current maintenance status of the drill rig. The drill rig is equipped with a speed sensor, pressure sensors in the hydraulics, 3-axis vibration sensor, borehole length measurement and temperature sensor. The sensors are additionally attached to the drilling rig and no structural changes on the drill rig are necessary. All data are processed real-time at a server structure outside of the mine using AI algorithms to analyze which rock (ore or host rock) is being drilled and to perform predictive maintenance. Processed Data are visualized for the operator to optimize the workflow and the productivity.

Feb 1, 2025

By Dennis Travagini Cremonese

In the early stage of front end studies of an Iron Ore Project, the sizing of surge capacities and stockpiles are normally assumed based on the experience of the study team. Understanding and sizing of these capacities at the early stages of the project are important for future stages of the project as drastic changes in sizes will impact the economics of the project at that stage. An innovative user configurable high level dynamic modeling tool has been developed to assist in speedy evaluation of assumptions made by the study team. This model incorporates systems or facilities that are commonly used iron ore project from mine to port. This model includes subsystems that will simulate all the logistical components, major process plant systems required for an Iron ore project. The output data provided by this high level dynamic simulation tool will enhance the confidence level of engineering carried out during the early stage of the project. This paper discusses the innovative tool capabilities and a test case comparing various techniques used in iron ore project front end studies.

Aug 1, 2018