Search Documents

By Hong Nguen Vu, Pavla Ovcarí, Peter Fecko, Barbara Tora

"The goal of the work was verification of bacterial leaching on the samples of black coal. From the results obtained it was clear that the coal is very well leached by Thiobacillus ferrooxidans and this technology can be used for coal desulphurization. A leaching time of one month is required, to remove 65% of total sulphur and 85% of pyritic sulphur.Microscopic evaluation of samples from Jaworzno showed, that it should be classed as a coal with low coalification, probably from black coal hemiphase. Macerals of the liptinite group were well distinguishable; they were of a dark brown colour. Evidence of coal mass oxidation was apparent on the fresh sample; in the test samples (during bacterial leaching) small grains were oxidised."

Jan 1, 2003

"The Merensky Reef is a platinum group minerals (PGM) bearing reef in the Bushveld Igneous Complex in South Africa. The reef has been treated by bulk PGM and sulphide flotation with the aim of maximisingthe valuable minerals recovery and gangue minerals rejection.Synthetic water with a calcium concentration of 80 ppm and 500 ppm was prepared and the flotation results obtained were compared to a simple electrolyte in order to determine the effect water quality has on pentlandite and pyroxene surface alteration and, ultimately, floatability. During the study, the possible effect of interactions between the minerals investigated and Ca2+ ions in the presence of sodium isobutyl xanthate was studied at pH 6 and pH 9 by means of zeta potential determinations, microflotation tests and ToF-SIMS analysis.The results obtained on 1:1 pentlandite-pyroxene mixtures showed that the quality of process water plays an important role in flotation. The flotation recoveries of pentlandite and pyroxene were lower in synthetic process water compared to those obtained in a simple electrolyte solution."

Jan 1, 2003

By M. Salas, L. Rolf, H. Z. Kuyumcu

"Industrial use of abrasive stress takes place in the area of fine grinding and in order to clean surface contaminated soil particles. Also, at many mechanical operations abrasion emerge as an unintended side effect. At the Institute for Raw and Waste Material Processing at the Technical University of Berlin systematic investigations are carried out, to further the knowledge regarding the dependence of abrasion process on material properties and stress mechanisms as a basis for design and optimisation of the process or for its avoidance. Aim was the mathematical description of the abrasion process running with a single particle stress. For the purpose of investigations an agitation cell was used. Limestone served as material.In the presented work the influence of particle diameter, particle shape and collision energy on the mass and particle size distribution of abrasion debris was studied. The surface geometry of the particle was characterised by the particle shape factor ?x and the particle diameter dp. The particle shape factor ?x stays in direct relation with the abrasion degree x, and can be substituted by a mathematical function of x.Physically the particle shape factor ?x can be interpreted as a proportion of abrasive stresses splitting up complete crystals and crystal fragments. These two different mechanisms depend on different ratios of curvature of the surface of the stressed particle. The abrasive stress of strongly curved surface areas leads to separation of complete crystals. The abrasive stress of weakly curved surface areas leads to separation of crystals fragments. Accordingly the mass of wear mAb and median diameter of the abrasion debris d50 are different. The derived mathematical relations consider this behaviour by the particle shape factor ?x , which represents the ratio of the mixture of both stress mechanisms. The dependence of the particle shape factor ?x on the abrasion degree x with an exponent approximately to 2/3 points out that the particle shape factor ?x represents a surface area relation."

Jan 1, 2003

By Susanna G. de Jager, Francis W. Petersen

"To enable the prediction of reagents suitable for fine coal flotation, it is necessary to develop a methodology applicable to different South African coal types. Statistical confirmation of the applicability of this methodology is important to avoid recommendation of reagents on a trial and error basis.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements. Flotation tests were used to validate expectations from the characterisation of the coal samples.RESULTSThe flotation data indicated that all of the coal samples were amendable to froth flotation. The best results were obtained with the Witbank seam 2 coal and the poorest flotation with Syferfontein seam 5 coal. The flotation tests showed that the best reagents to float all of the coal samples studied were iso-decanol and dodecene. These reagents produced flotation products that were near to the release curve, which are the optimum flotation results (obtained when using iso-paraffin as collector). Dodecene resulted in low ash products and iso-decanol in high yield products."

Jan 1, 2003

By Boris K. Krstev

INTRODUCTION The flotation process, in the real industrial complexes, is characterized by the existence of the significant number of the close reciprocal interrelationship between the input and output Darameters. Traditional complexity is appeared with regard to absence of the suitable a priori information for the physico-chemical characteristics of the flotation process. It’s led to needful of taking of consideration about the undefinition which have got the place in the real conditions and application of the statistical methods. The identification of the flotation process through statistical methods is conception of the more-stages procedure, including the collection and previous analysis, the choice of the model structure and valuation method, the estimation of the model un- known parameters and the results interpretation. The essential concept for the subject of this paper belongs to the empirical models ("black-box") and deals with optimizing in constant industrial plant process. The offered method envisages the application of process operation data in order to improve the work process or constant accomplishment of better results for the target function in relation to the former achievement. The optimum process solution isn't afixed value under the influence of various factors, but "a moving point" along the response surface and deviates from the scheme solutions. The evolutive planning method constantly "investigates and approaches" the optimum solution for the selected target function. As a matter of fact the expert operates the plant without interrupting the normal work process. The essential concept of method is to attain changes in the standard conditions, but so limited that they will not effect either production or the product. This method is based on statistical concepts and availability of following the risk of error. The possible influental factors for the flotation process (m=l, 2, 3) is following: the metal content in the feed ore; production level (t/h); grinding fineness in the flotation pulp; pH-values; the consumption of collectors and modifiers The possible target functions are: the recovery of plant capacity, metal recovery in the concentration process and concentration quality. The application of the evolutive operativity method in the chalcopyrite flotation- Bucim concentrator, combines the statistical data and the operator's experience in the interpretation and making a decision which adds up to the precise automatic performance of the process. The advantages of this method in relation to the existing procedure for the flotation process are the following: • The method is unexpensive and losses are reduced to the time necessary to collect the data and record them in the computer. This method provides a constant process control and a quality decision which is better than those brought by an ex- pert with great experience ("hit-and-miss method"). • The method also provides incidental data about the effects. • The method should not be considered as a procedure for solving an incidental problem ("crash program"). • The obtained results must be interpreted by an appropriate expert in order to be considered instructive. MATHEMATICAL STATISTICS Taking into consideration the complexity of the enrichment processes it's necessary the application of "black-box" and mathematical modelling. The presence of the indefinite elements compel us towards the both theory of the probability and mathematical statistics. The mathematical statistics by the mineral processing investigation of the valuable raw materials in the last years has had greater signifance and widely spread application. The application of the mathematical statistics methods for the technological pro- cess analysis and the construction of the mathematical models is bound up by the task putting of the automatic control system de- sign (Fisher R. A. 1941, 1949). The statistical analysis in the enrichment processes is applied formerly, especially in the sampling estimation. Contemporary, in the last years is imposed the tendency of mathematical statistics application for the obtaining of quantity characteristics and quantity valuation from the individual influental factors. Above mentioned tendency in the significant level is based by the mathematical statistics development as a mathematical discipline close connected with the technical cybernetics general joining to the investigated object as a "black-box". Another essential factor in the mathematical statistics development is appeared the created mathematical theory of experiments as a new, to some extent, autonomous statistical domain. The theory of experiments has demonstrated exclusively importance for the investigation of the complex more-factorial processes in the chemistry, mineral processing, metallurgy etc. The investigation by the enrichment processes of the valuable raw materials and their management is possible by the statistical method application. In the same time, it's possible to use the wide-spread traditional methods of the statistical analysis, such as the methods of the dispersion, correlation, regression etc. Also, it may be mentioned above all the methods of the statistical planning of the extreme experiments. The more perspective are representatived some cybernetic methods which are based by the probability as an approach in the process analysis, for example, the identify of the ways and forms, the graph application as an additional instrument in the correlation analysis, the dynamic programming etc. The mathematical statistics application in the laboratory investigation scale is connected above all by the experimented material analysis and the compact representation of the obtained results. The mathematical statistics methods are more varrying and may be applied in the investigations of the wide circle of problems

Jan 1, 1996

By J. H. Viljoen, A. Heyns, J. F. Morrison, C. H. Wyndham, N. B. Strydom

Discussion M. J. Martinson* (Associate Member): This is another interesting paper in the series which the Human Sciences Laboratory is publishing on the physiological cost of the more strenuous manual tasks performed underground. As a mining engineer-albeit presently an academic one -this contributor is more concerned with the practical significance of the study in the field of stope cleaning than with physiological niceties, but before discussing some of the practical issues raised by the paper perhaps the authors would care to reply to lay comment on three physiological matters. Firstly, in two places the authors make statements to the effect that the maximum oxygen intake of 'average' (sic) Bantu mine workers is 3.0 l/min. What do the authors mean by 'average'? Maximum oxygen intake in the individual is probably some function of inter alia age, physical fitness, state of health, ambient partial pressure of oxygen, diurnal and/or seasonal changes in metabolism, and possibly cumulative exposure to dust and other occupational contaminants. Since maximum oxygen intake is apparently such an important quality in manual labourers we ought to have a clear picture of its distribution in the entire labour force, and also know precisely how the individual's quantum is affected by factors such as those mentioned above. Secondly, arising out of the same statements and ignoring the reservation implicit in the previous paragraph, is it correct to say that the 'average' Bantu mine worker has a maximum intake of 3.0 l/min? In the August 1966 issue of the South African Journal of Science four of the present co-authors reported the mean maximum oxygen intake of a random sample of 338 Bantu recruits of different tribes to be 2.63 l/min with a standard deviation of 0.542 l/min, and these figures were repeated in a paper published in the November 1968 issue of this Journal. Admittedly the mean maximum oxygen intake of the six subjects used in the present study was 3.05 l/min, but since they were selected on the grounds of previous shovelling experience they can hardly be regarded as being 'average' recruits. Thirdly, it seems to me that the authors are perhaps a little uncritical in their acceptance of the '50 per cent of maximum oxygen intake' level of activity for endurance work. I am not unmindful of the evidence upon which this level is based, but I suggest that the evidence is at best tenuous and that the whole topic of fatigue and 'optimum' levels of productivity under conditions of high muscular activity and considerable psychological stress is a lot more complicated than would appear from the authors' ready acceptance of the 50 per cent level. Under present working conditions the question is largely rhetorical because it would need an army of supervisors to ensure that all members of a typical gang work at 'optimum' levels throughout the shift, but if individual performance should ever become more readily determinable the issue might become crucial to management and malayisha alike. So much for physiological matters; now a few random thoughts on some wider, practical issues raised by the paper. In the paragraph headed Material the statement is made that 'The mixture (of fine, medium-sized and bigger rocks) was considered to be representative of an average underground rock sample'. Elsewhere in the report the authors specifically draw attention to the effect of particle size on the oxygen consumption of men shovelling graded material, and intuitively one imagines that the size distribution of the material being shovelled would be highly significant in a study such as this. Presumably the authors were forced to assess size distribution subjectively because of the lack of objective data on the subject, and possibly the necessity for this assumption highlights how little we know quantitatively about any of the variables in stope cleaning systems. In this connection it may be remarked that although the present study was largely designed to show how dip and stoping width effect energy expenditure in shovelling, no data are given-nor, probably, are they available-to show how the industry's stoping tonnage is distributed in terms of these two factors. It seems to me that if the mining industry seriously hopes to improve stope productivity it must start by measuring the basic variables in existing systems. Elaborating somewhat on the previous paragraph, there also seems to be a tremendous gap between the present study-and its predecessors-and the prospect of gainfully using the information so carefully garnered by the authors. It would be reassuring to hear from the authors that their work on the physiological aspects is being integrated in some master plan for increasing productivity of manual labour. This I fear is not the case, and if productivity has changed at all in recent years I would hazard a guess that the change has been brought about by random factors rather than by systematic engineering design. The Human Sciences Laboratory has worked extensively in stopes in the past, and possibly the time has come when it should widen the ambit of its operations to include engineering-type analyses of cleaning systems, with particular emphasis on the economics of rapid cleaning by manual labour. Perhaps experiments could be conducted with stakhanovite-type gangs consisting of men selected for their high maximum oxygen intake and superior motivation; these men might be offered special incentives in the shape of extra pay

Jan 10, 1969

By A. A. Collins

When we speak of high copper on a lead blast furnace we think in terms of 4 to 5 pct, or. any lead charge carrying over 1 pct. Any copper on charge will produce its corresponding troubles such as lead well, extra slag losses, drossing problems, and the working up of the dross. This is indeed a very interesting subject and one that used to give the old-time lead metallurgists such as Eiler, Hahn and lles many worries, not so much in the actual operation of the hlast furnace but in the working up of the copper. When the American nletallurgists commenced with the American rectangular-shaped lead blast furnace in the 1870's and got away from the reverberatories such as were in use in Germany and other parts of the world, they went to greater tonnages, as 80 to 100 tons per day in comparison to the 20 to 30 tons per day in the other processes. With the greater tonnages along with insuficient settling capacity, the silver losses in some cases were increased. Hence the lead-fall was low, for there were no leady concentrates in those days to assist the metallurgist to gain lead or an absorber for the precious metals; and in some cases copper sulphides were added intentionally to the charge to produce a copper matte to lessen the silver losses through the dump slag. The operators in those days thought that where some copper was always present in the lead ores the copper should not enter into the reduced lead and alloy with it. This, by the way, is just the reverse of our present-day practice, when we try to put all of the copper into the blast furnace lead and to remove the same through the drossing kettles. Therefore the furnace was operated to produce a certain amount of matte or artificial sulphides, since, due to the great affinity of copper for sulphur, any copper present would enter the matte almost completely. Thus, the lead bullion produced was practically free from copper. The products of the furnace were metallic lead or lead bullion, containing 05 to 95 pct of the lead and about 96 pct of the silver which were in the ore—a lead-copper-iron matte which contained nearly all the copper in the ore and the slag, the waste product. In the United States, up through the year 1092, we find the small furnace 100 X 32 1/2 in. with 12 tuyeres, some 6 on each side, plagued with a small amount of poorly roasted sulphides— either from heap or hand roasters that produced matte. This matte was roasted and if poor in copper was returned for the ore smelting. Otherwise it was smelted either alone or with additions of rich slags or argentiferous copper ores, the products being lead and a highly cupriferous matte, the latter being subsequently worked up for its copper. The lead metallurgists kept trying and improving on furnace and roasting equipment designs until we find blalvin W. Iles constructing at the old Globe Plant at Denver what came to be the modern furnace. That is, in 1900 he built a furnace of 42 in. width by 140 in. at the tuyeres with a 10 in. bosh and a 16-ft ore column. This type has been more or less standard to the present time, though modified in width and length to meet the demand for large tonnages and improvements in structural details. In 1905 at Cananea, Mexico, Dwight and Lloyd developed the present down-draft sinter machine that has meant so much in producing a well-processed material for the lead blast furnace. In 1912 Guy C. Riddell came forth with double roasting at the East Helena Plant of the American Smelting and Refining Co., which removed the "zinc mush plague." Incidentally, with the introduction of double roasting, which most lead plants were forced into after 1924, when lead flotation came into its own, less matte or no matte was produced. When this stage arrived, the copper was forced into the dross and the casting of lead at the blast furnace lead-wells was stopped. In plants with a fair copper carry 1 pct or better on the blast furnace charge, the lead wells became inoperative once the production of matte stopped. The copper drosses clogged the lead wells and even with bombing, either water or dynamite, the operators could not keep them open. Thus, the lead wells were abandoned in some plants, such as at the El Paso and Chihuahua smelters of the American Smelting and Refinillg Co., and all lead taken out through the first settlers. The elimination of sulphur, espccially sulphide sulphur, from the blast furnace charge and the nonproductiori of matte resulted in a great saving of tinie, energy and equipment in the recirculation of the copper, With the copper content in the dross and dross-fall ranging in quantities from a few percent up to 60 pct, such as at El Paso, a drossing problem was created. As the old-time operators hated dross and buried the same in the shipping bullion, the modern metallurgists from 1925 on decided that with increasing dross-falls they would have to adopt the lead refiner's ideas of drossing kettles with subsequent treatment of the lead with a sulphur addition to have the shipping lead of 0.01

Jan 1, 1950

Jan 1, 1934

By Linda Lee, R. E. Reed-Hill, C. R. Smeal

Four fcc metal surfaces, etched to make them responsive to polarized light, have been studied with an electron microscope. Jones'prediction that these surfaces are grooved has been verified. Optical-goniometer measurements made on commercially pure nickel indicate that the groove walls are poorly defined (100) facets. Surface mientations close to either 4001 or {ill).- show no extinctions on the polam'zid-light microscope. An explanation is offered for this orientation dependence. It has also been deduced that polarized-light extinctions on a grooved cubic-metal surface should not be used directly in crystallographic-orientation determinations. The nature of the etching solutions that produce these surfaces is considered. A cubic-metal surface may be made responsive to polarized light in two basic ways."' In one, an anodic film, believed anisotropic, is formed on the surface. A plane-polarized-light beam, at normal incidence, should be reflected from this type of film with an ellipticity that varies with grain orientation. Under crossed polarizers of a polarized-light microscope, each grain may be distinguished from its neighbors by a difference in reflected-light intensity. An alternate treatment,' more generally applicable to cubic metals and of principal concern here, involves etching of grain surfaces. The characteristic features of this surface were first deduced by Jones3 from light-microscope observations. She concluded that, in general, grain surfaces were furrowed so that light was reflected from two parallel sets of etched facets. A grooved surface produces elliptical polarization of a plane-polarized beam because the beam does not strike groove walls at normal incidence. Jones also observed that the furrows must have faces inclined to each other by approximately 90 deg, since the light returns along the incident path, and that a grooved surface should show four maxima and minima of reflected-light intensity during a 360-deg stage rotation of the polarizing microscope. Positions of maximum extinction were predicted to occur when groove axes were parallel to either polarizer or analyzer vibration directions. Because of the limited resolving power of Jones' optical microscope, her deductions were primarily indirect. Proof of the correctness of her conclu-sions, as demonstrated by the electron microscope, will be given as well as evidence concerning the crystallographic nature of the etch furrows and the types of etching solutions that produce them. EXPERIMENTAL PROCEDURE During a comprehensive study of hot plastic deformation in nickel and nickel alloys, an etch was evolved that produced a surface with an excellent polarized-light response on Nickel 200 ("A" Nickel). The etching solution and associated metal-lographic procedures are given in Table I. In evaluating this etch, a study was made of the topological features of the etched surface and their relation to the underlying crystalline structure. As part of this investigation, large crystals (2 mm average diameter) were grown in a 1-cm-sq Nickel 200 specimen. After the surface was etched, the crystallographic orientations of ten grains were determined by the standard back-reflection Laue technique of Gren-inger.4 Maximum extinction positions during a microscope stage rotation were also measured for the ten grains. Groove-wall positions on the surfaces of the ten grains were measured with a two-circle optical goniometer. The technique was essentially that of Barrett and Levenson.5 Several grain surfaces were photographed with a Philips Model 100A electron microscope. All specimens were replicated with collodion, or collodion backed with formvar and chromium shadowed at 18 to 20 deg. The basic material was Nickel 200. However, an electron-micrographic study was also made of surfaces developed by polarized-light etches on other fcc metals (90-10 a brass, Monel 400, and lead). All etching procedures are given in Tables I and 11. EXPERIMENTAL RESULTS Fig. 1 shows typical electron micrographs of three different fcc metal specimens and an optical micrograph of a fourth. All photographs show a grooved structure corresponding closely to Jones'3 predictions. Also, as noted by Jones, extinctions were always observed when groove axes were either parallel or perpendicular to the microscopes' vertical cross hair. The symmetry of the grooves, with respect to the twin boundaries in Fig. 1, implies that furrows have a crystallographic basis. The coarse-grained Nickel 200 specimen was used to study this basis. Facet Orientation. The poles of the ten Nickel 200

Jan 1, 1964

By E. R. Helderman, C. Y. Ang, C. C. Nealey

Beryllium-base alloys have been successfully p7.-epared by the liquid-phase sintering technique. Depending orz the composition and amount of the intended liquid please, microstructures either single -phase or duplex in feature with randomly oriented grains have been obtained. Qualitative and semi-qualitative determination of distribution of alloying elements md microsegregations in some experi)uzental alloys haue been made by electron-micro-probe analysis in conjunction with microliardness testing and standard metallography. Tensile tests reoealed that some conzpositions possess attractive elastic properties with Young's mot1uli greater than 40 X 10' psi. In powder metallurgy, liquid-phase sintering is a process or phenomenon that has proven to be of practical value. For example, the heavy metals such as tungsten-copper-nickel, high-strength heavy gyro alloys,' heavy-duty electrical contacts,' and tungsten carbide tool materials are all products of liquid-phase sintering. Mechanisms involved in liquid-phase sintering, however, are not completely understood. Questions regarding the exact roles played by rearrangement of particles, liquid/vapor surface energy, solution and precipitation, and so forth, have not been completely answered. Evidence has been cited3 that at least volume shrinkage in the densification process is diffusion-controlled. It is possible that the predominant mechanisms for the complete densification and grain growth in a liquid-phase sintered system depend primarily on the alloy systems involved, in addition to processing conditions. Despite the lack of sound understanding of the mechanisms of the process, liquid-phase sintering has been and is being used to advantage either to synthesize microstructures for their special properties or to prepare alloys which are difficult to form by fusion process. Liquid-phase sintering of beryllium alloys was first attempted by Jones and Williams.4 They first tried infiltrating beryllium with magnesium, and then succeeded in preparing the alloy by sintering Be-Mg powder compact in molten magnesium bath. This investigation resulted in the identification of some Mg-Be intermediate phases. Crossley et a1.5 also used liquid-phase sintering technique in an attempt to produce ductile beryllium alloys for structural applications. The major liquid-phase components investigated by Crossley et al. were aluminum and silver with minor additives of germanium, calcium, lanthanum, cerium, and yttrium. The lack of wetting and the bleeding out of liquid phase were the difficulties encountered during experimentation. According to Hodge,6 the two compositions investigated by Crossley, which showed some promise based on compression tests, involved large amounts (over 35 wt pct) of silver, thus making them too heavy to be of practical interest to the aerospace industry and military users. The present investigation was prompted by the search for light-weight (density less than aluminum) beryllium alloys exhibiting small anisotropy in physical properties for precision inertial navigation instrument applications. In addition to isotropy, good structural properties such as high elastic modulus or desirable combination of mechanical and physical properties are also objectives of this investigation. The technique of liquid-phase sintering was chosen for its versatility in producing either duplex or homogeneous microstructures. This report is concerned with the use of copper and aluminum, with or without silicon addition, as the intended liquid phase, and the resultant micro-structures and some physical properties of the beryllium alloys. Qualitative and semiquantitative electron-microprobe analyses of some of the alloys are presented to illustrate the usefulness of this microanalytical technique for the identification of microconstituents and their distribution. EXPERIMENTAL PROCEDURES The beryllium powder used was -200 mesh Brush Beryllium Co. QMV NP-50 grade. Typical chemical analysis of the powder is shown in Table I. Commercial high-purity copper, aluminum, and silicon powders all screened to —100 mesh were used as additions. Mixed powder compositions were ball-milled in ceramic jars for 1/2 hr to ensure thorough blending. Milled powder was loaded either in 3/4-in.-diam button die or in Metal Powder Association flat tensile specimen die and compacted under top and bottom pressure. No lubricant or organic binder was used. Sintering was carried out in a quartz tube under a vacuum of 50 to 100 µ pressure. Surface hardness and some microhardness readings were taken on sintered specimens. Sintered density was

Jan 1, 1965

By Donald B. Evans, Robert D. Pehlke

The solubility of nitrogen in liquid Fe-B alloys has been measured up to the solubility limit for the formation of boron nitride. The activity coefficient of nitrogen increases with increasing boron content in the range 0 to 7 wt pct B. From experimen -tal data, values have been calculated for the B-N interaction parameter e3 at temperatures in the range 1550" to 1750°C. A value of 0.038 has been estimated for the boron self-interaction parameter eg at 1550°C. The standard free energy of decomposition of boron nitride into the elements dissolved in liquid iron has been determined to be: ?F° = 45,900 -21.25T in the range from 1550° to 1750°C. The nitride is assumed to be of composition BN. BORON nitride has an unusual combination of properties which make it appear attractive in a wide range of engineering applications. Some of its more important and most recent applications are in the nuclear area, particularly in connection with the liquid-metal cooled reactor concept now receiving considerable emphasis. Boron nitride has a high degree of stability at elevated temperatures. It also has excellent ma-chinability and the ease with which its crystals deform suggests applications as a lubricant. These properties stem from a hexagonal layer-type structure similar to the structure of graphite. One of its primary uses to date has been for seals in liquid-metal pumping systems. It is also used in nuclear reactors as an insulating layer to separate two solid metals which are not themselves compatible under the conditions of temperature and atmosphere in which they are used. Its inertness to liquid metals has also suggested use as a mold-release agent in casting processes. In addition to its excellent machinability and reported inertness to liquid metals such as iron, silicon, aluminum, copper, and zinc, boron nitride has high thermal conductivity and excellent thermal shock resistance. This combination of properties would make it appear ideal as a refractory crucible material for refining of high-purity liquid metals, for example high-quality steels. However, since it is known that concentrations of boron as low as 50 ppm can have a marked effect on the physical properties of certain steels,' in particular on the creep and stress-rupture properties, an investigation was undertaken to define accurately the chemical equilibrium among boron, nitrogen, and liquid iron in the range of steelmaking temperatures. EXPERIMENTAL PROCEDURE Two experimental approaches to this problem were employed: a Sieverts' method and a quenching method. In the first method, the Sieverts' technique was used to measure the equilibrium nitrogen solubility in liquid Fe-B alloys of 0 to 7 pct B as a function of nitrogen gas pressure over the melt. The solubility limit of the boron nitride phase formed was determined by the point of departure of the nitrogen absorption from Sieverts' Law. This technique has been applied to liquid Fe-Ti alloys by Rao and parlee,' to liquid Fe-A1 alloys by Evans and Pehlke,3 and to solid Fe-V alloys by Fountain and Chipman.4 In the second method a melt of liquid iron was held in a crucible of boron nitride under a known partial pressure of nitrogen gas. After thermodynamic equilibrium was attained, the melt was quenched in a stream of helium and then analyzed by wet-chemical methods for boron and nitrogen. The Sieverts' apparatus used in the first method was essentially of the same design as the one described by Pehlke and Elliott.5 The charge materials were vacuum-melted high-purity iron (Ferro-vac E) supplied by the Crucible Steel Co. and -325 mesh boron powder supplied by Cooper Metallurgical Associates of Cleveland, Ohio. The boron contained less than 0.02 wt pct O, according to supplier's analysis. Recrystallized alumina crucibles were used to contain the melt. Examination of solidified melts showed these crucibles to be satisfactory with no evidence of any reaction or physical penetration of the crucible wall by the melt. The melt temperature was measured by a disappearing filament-type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diam sight hole in the crucible lid. The pyrometer was calibrated against the melting point of pure iron in the same apparatus, taking the emissivity of

Jan 1, 1964

By Robert E. Green, P. W. Kingman

Application of a constant geometry compression test to single crystals of aluminum of selected diameters from 1/4 to 1/64 in. showed the presence of a diameter-dependmt size effect. The most pronounced effects were found in those crystals oriented for single slip, while for specimens possessing orientations in the comers of the standard stereographic triangle virtually no size effect was exhibited. The yield stress of the crystals oriented for single slip was found to increase with decrease in specimen diameter, while the strain-hardening rate was found to be lower for the smaller specimens. The experimental results are in general agreement with those of other investigators obtained from lensile tests on copper and aluminum crystals. THE earliest systematic investigation of a possible size effect on the plasticity of metals was that of no,' who in 1926 performed tensile tests on cylindrical aluminum single crystals with diameters of 3 to 8 mm. Ono concluded that the gross stress-strain curve did not show a diameter dependence, but that the resistance to slip for strains of 0.1 pet and less appeared higher for 3-mm-diam crystals than for larger sizes. Later studies of aluminum by Maddin et al2 tentatively concluded that a size effect exists, but the conclusions were again open to question because of inconsistencies in the experimental data. Wu and Smoluchowski3 had previously shown that the slip system activated in a single-crystal sheet specimen of aluminum is a function of the specimen cross section in the slip direction, but no stress-strain data were obtained. Subsequently Fleischer and Chalmers4 studied the effect of the length of the slip direction of the primary-slip system on the stress-strain curve by testing aluminum crystals with geometrically dissimilar cross sections. In the course of this investigation a size effect was indicated in rather large crystals; however, the number of these tests was small. Other investigators have indicated that a size effect in aluminum is appreciable only for diameters of 0.5 mm or less.5, 6 Size-effect studies have also been carried out on copper crystals, the most detailed being that of Suzuki et a1.7 who performed tensile tests on specimens of many diameters ranging from 2 to 0.12 mm. Suzuki found a strong size dependence in the easy-glide region, both the extent of the easy glide and the hardening rate in easy glide were size-dependent, and the size effect was found to be orientation-dependent. Suzuki's results are in agreement with the less extensive observations of Pater-sonB and those of Garstone et al.9 A size effect was found by Rebstock using tubular copper crystals.'0 Size effects have also been noted in a brass,6, 11 in cadmium,12'19 and in hexagonal crystals.14 All the previously cited works have been entirely concerned with the variation of specimen cross section. The effects of specimen length and the change of specimen geometry which results from using progressively thinner specimens while maintaining the same specimen length have been largely ignored. A theoretical discussion of the effects of specimen length and geometry has been given by Hauser and Jackson,15 who predict a grip effect on easy glide as a function of specimen geometry provided that the specimen dimensions are large compared with the spacing between the slip bands, and by Fleischer and Chalmers,18 whose analysis of grip effects resulting from lattice rotation predicts an increase in easy glide with an increase in specimen length. A study of size and geometry effects in aluminum crystals by Kitajima and shimba17 indicated increasing amounts of easy glide in specimens of increasing length and identical cross section, and nearly identical stress-strain curves for specimens of different sizes having constant length-to-diameter ratios. Since the present study is primarily concerned with diameter dependence, the following factors were taken into account: specimen material, specimen geometry, testing method, range of sizes to be tested, and possible influence of surface and volume effects. Aluminum was chosen because of the present lack of conclusive results and the seeming possibility of size effects at relatively large diameters, the

Jan 1, 1964

By J. W. Downey, S. T. Zegler

A study has been made of the occurrence of Phases having the Cr30-type structure in ternary alloys having the general composition where B cept for iron and copper all the B components are known to form binary compounds having the type structure. The occurrence of the struc-ture type in the ternary alloys was investigated using optical and X-ray metallography. The results indicate that iron can replace virtually none of the cobalt in at 900°C, but substitutes for nickel in up to the approximate composition tually insoluble in V3Ni and 2) and exhibit complete solubility. At 100 nickel can be substituted for cobalt in VSCo up to the composition solubility; and 3) in the system , two solid solutions having the type structure occur. At the same temperature, 1000°C, V3Si exhibits limited solubility for V3Co but is completely mis-cible with V3Ga. Lattice parameters have been determined for all the binary and ternary phases. The solid solutions are discussed in terms of the atomic size and electronic factors which are thought to influence the occurrence of Cr30-type phases. The binary compounds V3Co and V3Ni were found to form peritectoidally from o phases and a vanadium, the former compound at a temperature between 1000" and 1050°C, the latter between 800°and 900°C. The substitutions of nickel and rhodium for cobalt in V3Co were determined not to raise the superconducting transition of VSCo to a temperature as high as 2°K. The occurrence and stability of binary intermediate phases having the Cr30- or A15-type structure (space group o;, Pm3n) have been discussed in several recent papers . Vanadium forms the struc -ture at or near V3B stoichiometry with all the mem -bers of the cobalt and nickel groups in the periodic table and also with Au, Ga, Si, Ge, Sn, P, As, and Sb. This paper describes a survey of the occurrence of the CrsO-type structure in ternary alloys having the general composition V3(B, B') where B and B' are Fe, Co, Ni, Cu, Rh, Ir, Si, and Ga. The purpose of the survey was to clarify the connection between the position of the B partner in the periodic table and its CrsO-type phase-forming tenden~y.~,~ The survey is part of a broader program concerned with the influence of B-partner substitutions on the superconducting transition temperatures of CrsO-type compounds. The transition temperatures, Tc, of some of the ternary Cr,O-type phases found in the survey are also discussed in this paper. EXPERIMENTAL PROCEDURE The alloys were prepared by arc-melting in an A-He atmosphere and were in the form of buttons, weighing approximately 3 g. The metals used in their preparation were received from commercial sources and were in all cases 99.9+ pct pure. The vanadium was spectrochemically pure except for 800 ppm of Si, 200 ppm of Fe, and 200 ppm of Al. For study of each pseudobinary system at least seven alloys were prepared having the general compositions case of alloys containing gallium, melting losses were small, usually less than 0.3 pct of the total weight of the metals charged for melting. Melting losses were somewhat greater for gallium alloys, ranging in general from 0.9 to 5.0 pct. Ternary V-Si-Ga alloys were chemically analyzed and the results are given in Table I. The analyses show most alloys to be within 2 at. pct of the intended composition. Throughout the balance of the paper the intended compositions are used in discussing the alloys. The cast buttons were annealed within evacuated quartz capsules for times ranging from 3 to 6 weeks at temperatures between 800" and 1000°C and water-quenched. The phases present in the annealed and quenched alloys were identified by optical and X-ray metallography. X-ray diffraction photograms were made with powders prepared from the bulk specimens, by the use of a 114.6-mm-diam powder camera with copper irradiation. The lattice parameter of CrsO-type phases and their standard errors

Jan 1, 1963

By John M. Tinsley, Calvin D. Saunders, H. K. van Poollen

In the past few years much con-sideration has been given to the evaluation of the effect of hydraulic fracturing on the productivity of wells. Generally, these studies included the evaluation of fracturing materials, fracture extension and formation damage due to the use of various fracturing fluids. Only little consideration has been given to the characteristics, and in particular the flow capacity, of the fracture itself and its effect on well productivity. This paper presents the results of laboratory investigations pointed toward fie evaluation of the efficiency of various fracrures with special emphasis on the flow capacity of these fractures. Data presented in this paper are the results of both an electrical model study and physical testing. Under consideration are (I) effect of overflush, (2) premature production of well after treatment, (3) "tailing-in" with coarse sand near the end of the treatment, (4) effect of propping agent size and concentration, (5) reduction in effective frac-ture permeability caused by formation caused by formation fines, silt and clays, and (6) effect of various fluids on formation strength and competency. The results of this investigation indicate that the flow capacity of a fracture is affected by any or all of the various parameters mentioned above. The authors believe that a better understanding arid utilization of these factors should result in more efficient formation fracturing. INTRODUCTION Hydraulic fracturing has become almost a standard practice of many companies for stimulating production from old and new wells. Although most companies utilize this service, techniques of application vary widely between companies and areas. Probably too often when a well in an area responds favorably to a particular technique all future wells in the same area are treated in a similar manner. Possibly a modification of the technique would result in a further production increase. Variables, of which many are extremely difficult to evaluate from field results, hamper the selection of procedure changes. Attempts are being made by a number of organizations to analyze statistically treating techniques from production data. This is a very worthy and necessary approach but very possibly laboratory investigations may aid in evaluating some of the variables which tend to affect the results of a fracturing treatment. Some of the factors cannot be studied from practical field experience and only laboratory tests can show the possibilities which might exist. One of the factors which appears to be of major concern today is the flow capacity of the created fracture and how it can be changed. Papers on this general subject have been primarily concerned with the size of propping agent and the extent of fracture. Papers have also been written on the possible permeability damage to formations by fracturing fluids. In addition, it might be possible that another type of flow restriction is prevalent. This would be a restriction of flow through a sand-packed frac- ture caused by foreign materials integrating within the propping agent. This paper presents preliminary data obtained in an attempt to evaluate the effect of some factors affecting flow through sand-packed fractures. No attempt is being made to offer a fracturing technique adaptable to all areas and conditions, but to furnish data tending to show the possible effects which might be caused by variations in procedures and materials. PROPPING AGENT PERMEABLLITIES A hydraulically induced fracture containing sand as a propping agent may theoretically be classified as a packed-sand system. The flow of fluids through such packed systems has been the subject of much research. Although there have been numerous methods proposed for the evaluation of such systems, most writers agree on the general properties affecting their flow capacity or permeability. These properties include porosity, particle size, sphericity and the roughness of the particle. In some methods of evaluation . the particle size and sphericity terms are combined to produce an equation which is a function of the surface area of the particles. In this study the permeability of various fracturing sands was both measured and calculated. The apparatus for the permeability measurements consisted of a 52-in. Lucite tube with a 2.5-in. ID. A screen and drain plug were fitted in the bottom of this tube to retain and hold the sand in place while allowing fluid flow. Two pressure taps consisting of thin, highly perforated

By G. W. Tracy, R. D. Carter

Numerical calculations were made to determine the behavior of reservoirs with high-pressure drawdown and wide well spacing where the initial productivity is low and the wells are completed by hydraulic fracturing. The two-phase flow equations were solved for the flow into a single well. This well was assumed to be producing from a reservoir with hydraulically created horizontal fractures (four different systems with fractures were studied). For comparison purposes, additional two-phase flow calculations were made assuming a reservoir with uniform rock properties. The two-phase flow results were also compared with the conventional calculation methods, which do not include the effect of saturation gradients resulting from a simultaneous flow of oil and gas which are normal to this type reservoir. It was found that the conventional methods predict (1) a high and too optimistic value of ultimate recovery, (2) a high producing rate and a high reservoir pressure at a given oil recovery and (3) a low trend of gas-oil ratio with oil recovery. Included in the two-phase flow calculations were provisions to control the oil production rate by an allowable rate and, also, by a gas-oil ratio penalty rule. For the systems with hydraulic fractures, the producing rate was controlled by the gas-oil ratio penalty rule for most of the life. This is in contrast to the system with uniform rock properties which went "on decline" almost immediately. An unexpected characteristic of the systems which included fractures was the early rise in producing gas-oil ratio from 730 cu ft/bbl to approximately 1,200 cu ft/bbl, followed by a "leveling off" before the normally expected gas-oil ratio rise began. Additional features which are a result of hydraulic fracturing are (I) greater ultimate recovery, (2) higher average producing rates and (3) a lower average reservoir pressure at a given oil recovery. INTRODUCTION Some oil fields discovered during the past few years are producing from certain volumetric ally controlled reservoirs (often referred to as solution or internal gas- drive reservoirs) which are characterized by high-pressure drawdown at the wells. Since the available pressure drawdown at a well is limited by the static reservoir pressure and the producing rate is controlled by the available drawdown, wells completed in this type of reservoir usually produce at a rate less than the allowable from the time of completion. Because of this, this type of reservoir is referred to as a low productivity reservoir. Economic considerations require the use of wide well spacing and well stimulation by hydraulic fracturing to make commercial wells in this type of reservoir. Performance predictions for volumetrically controlled reservoirs have been made using a combination of two standard equations. 1. The "Schilthuis" or "Muskat" type material balance equation is used to relate the average reservoir pressure and the cumulative oil recovery. 2. The results from the material balance equation and the productivity factor as described by Pirson' are used to relate the cumulative recovery with producing rate and time. The material balance equation assumed uniform pressure and liquid saturation conditions throughout a reservoir. The steady-state radial flow formula allows for a pressure gradient toward a well but assumes uniform liquid saturation. These calculation methods are adequate for application to reservoirs wherein the drawdown at the well to realize satisfactory producing rates is small compared to the total pressure. In low productivity, volumetrically controlled reservoirs, the pressure drawdown at the well is large cornpared to the total pressure. Although a precise number cannot be given for the magnitude of a large pressure drawdown, values in excess of 1,000 psi would definitely be included. For practical considerations, this usually occurs when the formation flow capacity is less than about 100 md-ft. However, this limit of formation flow capacity will vary with the well producing rate. The low pressure in the neighborhood of the well which results from a high drawdown causes evolution of large volumes of gas. This causes the gas saturation to be higher near the well than at a greater distance—-hence, a non-uniform gas saturation. Also, the relationship between the relative permeability to oil (K/K) and gas saturation is nonlinear but decreases approximately in an exponential way with increases in gas saturation. Because of this, the following chain reaction is established.

By Peter Grundy

La eficiencia de los recursos en los procesos transparentes de gestión de las empresas permite aumentar el valor de los accionistas. En ese sentido, el presente texto señala el uso de la RCM como estrategia en el funcionamiento de un equipo que se centra en la confiabilidad. RCM es un proceso lógico que involucra aspectos técnicos y de negocio, capaz de producir resultados a muy corto plazo. Este proceso concluye con una recopilación de documentos fiables y totalmente óptimos para el desarrollo de las funciones de mantenimiento. Su uso correcto en la evaluación de los requisitos de mantenimiento de los equipos existentes, genera un mantenimiento menos costoso, confiable y eficaz. Asimismo se disminuye los costos de mantenimiento y se relaciona los aspectos ambientales y de seguridad.

Jul 17, 2000

By Carl Fisher

A microseismic roof fall warning system was field tested in Western and Eastern coal mines in the United States to better define the capabilities and limitations of the microseismic method in predicting roof fall Microseismic event and energy type data were obtained and documented for twenty-three coal mine roof falls. Field test results indicate that both the microseismic event and energy methods, as applied in this development effort, have a high probability for successful application in a commercially practical roof fall warning system. Based on the results and experience obtained during field testing, a commercial prototype microseismic roof fall warning system was designed and constructed. Although it was the intent of the program to field test the commercial prototype system, delays in equipment fabrication and contract time limitations did not permit field testing.

Jan 1, 1980

By H. B. Probst

Mechanical twins were produced in zone-refined tungsten single crystals by explosive working at room temperature. These twins are parallel to (112) planes and have irregular boundaries rather than the classical plane twin boundaries. These boundaries aye grooved surfaces in which the grooves themselves are parallel to a <111> direction and the sides of the grooves appear to be par-allel to (110) planes. TWINS were produced in tungsten single crystals by explosive working at room temperature. These twins differ in character from any previously reported for tungsten; however, they are similar to those found in molybdenum after compression at -196°C.1 Deformation twins "resembling Neumann bands in ingot iron" have been observed in tungsten by Bech-told and Shewmon.2 This observation was made with sintered polycrystalline tungsten pulled in tension to fracture at 100°C and using a strain rate of 2.8 x 10-4 sec-1. More recently Schadler3 found deformation twins in zone-refined tungsten single crystals pulled in tension at -196"&apos; and -253°C. These tests were conducted using a strain rate of 3.3 x l0-4 sec-1, and the twin bands were found to be parallel to a (112) plane. Deformation twins in tungsten&apos;s sister metal, molybdenum, were observed by Cahn.4 These twins were produced by compressing small (0.7 mm) vapor-deproducedposited molybdenum single crystals at -183°C. The compression was performed &apos;by impact." By the use of precession X-ray techniques, Cahn was able to identify the twin plane as {112} and the shear direction as <1ll>. Mueller and Parker1 produced deformation twins in polycrystalline electron-beam-melted molybdenum by compression at -196°C. Their "loading rate" was 5000 psi per min which, judging from their stress-strain curve, corresponds to a strain rate of approximately 0.3 x 10-4 sec-1. These twin bands were found to be parallel to (1 12) planes; however, they differed in appearance from previously observed twins. In place of straight and parallel twin boundaries they were found to be irregular, jagged, and sawtoothed. The sides of the saw teeth were identified as (110) planes and irrational planes of a (111) zone. The twins observed in the present work in tungsten single crystals are similar in appearance to those of Mueller and Parker in polycrystalline molybdenum. The starting material used in this investigation was 3/16-in. diam commercial tungsten rod produced by powder-metallurgy techniques. This material was converted to a single crystal by the electron-bombardment floating-zone technique.= The process was carried out in a vacuum of 10-5 mm of Hg using a traversing speed of 4 mm per min. Segments (=2 in. long and 3/16 in. in diam) of two crystals (A and B) produced in this manner were studied. Crystal A received one zoning pass, while crystal B received two passes. The two crystals were explosively worked at Bat-telle Memorial Institute in the following manner. A 1/2-in.-thick layer of plastic was applied to the crystals to serve as a buffer in an attempt to prevent cracking. The composite, crystal and buffer, was then wrapped with 1/8-in.-thick DuPont sheet explosive EL506A2 and detonated in water at room temperature. Metallographic samples of the worked crystals were prepared, and back-reflection Laue X-ray patterns were obtained using unfiltered molybdenum radiation. RESULTS AND DISCUSSION Blasting the crystals as described above failed to prevent cracking. The crystals fractured into several fragments about 3/16 to 1/2 in. long; however, the fragments were of sufficient size to be useful for the subsequent study. The diamond pyramid hardness of the crystals after blasting was in the range 430 to 450 as compared with 340 for the as-melted material, which shows a definite hardening resulting from plastic deformation. These hardness values were obtained using a 1000-g load and taking readings only in sound portions of the crystals free of cracks. The crystals exhibited profuse twinning as shown in Fig. 1. No such structure is present in the as-melted condition. Most of these twins have jagged twin boundaries and are similar in appearance to those found in molybdenum by Mueller and Parker. The twins in both crystals were found to be parallel to {112} planes. This identification was made by using the conventional two-trace method. Subsequent efforts to describe these twins more fully were carried out on crystal A. If the longitudinal axis of crystal A is placed in the (001)-(011)-(Il l) basic triangle of the standard cubic stereographic projection, as in Fig. 2, then the two sets of twins shown in Fig. 1 are parallel to the (112) and (121) planes. Fig. 3 shows a schematic representation of a twin with jagged boundaries. This type of twin with a <111>

Jan 1, 1962

By W. A. Backofen, R. L. Fleischer

Single crystal, bicrystal, and polycrystal tensile tests of aluminum at 4.2°K, 77°K, and 300°K have been used to examine the role of grain boundaries in the deformation process. Results indicate that a grain boundary may affect the extent and slope of easy glide. The stage II hardening rate, on the other hand, is independent of the presence or absence of grain boundaries. This conclusion allows the size of the region of multiple slip caused by an incompatible grain boundary to be determined. For the size of bicyystal sample used in this study, multiple slip occurs in about half of the cross section. PREVIOUS studies of the stress-strain characteristics of bicrystals of face-centered-cubic metals have been limited to aluminuml-5 at room temperature. Recent results, however, indicate that the stress-strain curves of single crystals of such metals may be separated into at least three stages6 in which different deformation processes are occurring7 provided testing is done at sufficiently low temperatures.&apos; Since for aluminum a well-defined stage II develops only below room temperature, previous studies have not been able to relate effects of grain boundaries to all of the three stages of deformation. It is therefore to be expected that low-temperature deformation of aluminum single crystals and bicrystals should clarify the effects of grain boundaries on the different processes of deformation. EXPERIMENTAL PROCEDURE Single crystals and bicrystals were grown from the melt by the standard techniqueg with aluminum reported by Alcoa to be 99.993 pct pure. Ridges in the boat were used to guide the grain boundary during growth, assuring that the boundary would bisect the sample.10 The rate of furnace motion during growth was 1.0 cm per hr. During growth zone purification resulted, as evidenced by the ability of the first material to freeze to recrystallize at room temperature following severe deformation. Samples were approximately 4.4 X 6.6 mm in cross section and 103.5 mm in length between grips. Samples were annealed at 635" i 5°C for 40 hr and furnace cooled over a 7-hr period. They were then electropolished in a solution of 5 parts methanol to 1 part perchloric acid at a current density of 15 amp per sq dm for about 30 min at temperatures below 0°C. Tensile testing was performed at 295" (room temperature), 77" (sample in liquid nitrogen), and 4.2"K (sample in liquid helium) on the hard-type machine indicated schematically in Fig. 1. The machine con- sists basically of a tube surrounding a rod; one end of the sample is attached to each member, and the rod is pulled up the tube to extend the sample. The rod is rigidly mounted and is moved vertically by a system described by asinski." The pulling force is measured continuously by an electrical strain gage load cell, and the relative displacement of the tube and rod is also recorded continuously by a soft cantilever beam with electrical strain gages. Maximum stress and strain sensitivities were ±2g per sq mm and * 3-10-5. In all tests the strain rate was approximately 5.10-5 per sec. The thin wires in the tensile apparatus introduce softness, which may be corrected for, however, by measuring load vs displacement with the sample replaced by an elastic member. For loads greater than 15 kg the spring constant is 1.875.106 g per cm. The flexible wires also served to reduce substantially the large shearing forces which may arise in the case of grips having horizontal rigidity.&apos;&apos; As in any gripping system, however, bending moments will arise in the course of deformation by single slip. Engineering stress, s = (load)/(original cross-sectional area), and strain, E = (increase in length)/ (original length), are used for stress-strain curves unless otherwise indicated. Tables list resolved shear stress, T=mo and shear strain ? = dm, where m is the usual Schmid resolved shear stress factor for the primary slip system at the start of deformation. The first group of samples to be described forms an isoaxial set, all of the crystals making up the single crystals or bicrystals having the same tensile axis, the orientation of which is indicated by the cross in Fig. 2. For this orientation the primary slip plane and slip direction make angles of 45 deg with the tensile axis and the Schmid factor m has its maximum possible value of 0.5. Rotations about the tensile axis are indexed by means of an angle 0 between the small-area surface of the samples and the projection of the primary slip direction onto the cross section, as defined in Fig. 3. In single crystals, values of 0 were 0 and 90 deg, while in bicrystals 0 values were (0 deg, 180 deg), (90 deg, 270 deg), and (0 deg, 90 deg) as indicated in Fig. 4.

Jan 1, 1961

By B. W. Clyburn

"Coals from the Corporation&apos;s Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing a/l essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.IntroductionVery high fluidity and unusually low ash are the outstanding characteristics of coal from Devco&apos;s mines in the Harbour seam of the Sydney coal field.However, sulphur content, mainly pyritic, ranges from 1 to 2.5070. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required .Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs.Typical data on the various coal properties of importance in the production of coke are included in Table I. Necessity of Low-Gravity SeparationThe design of any coal preparation plant requires the study of washability properties of the coal to be treated to determine the quantity and quality of coal produced at a given specific gravity along with the difficulty in accomplishing that separation.Their low ash content allows the important washability aspects of Harbour seam coals to be represented by sulphur! specific gravity curves (Fig. I). This particular example indicates that a yield of 54.5% is attained, at a sulphur content of 1.20%, for a perfect separating device operating with a 1.29 S.G. cut point.Material rejected from this separation still contains usable coal, which is recovered as middlings by separating at a higher gravity."

Jan 1, 1980