Search Documents

By Joan T. May

The Federal Bureau of Mines investigated the potential for recovering aluminum from copper-dump leach liquors by use of single-contact ion-exchange technology. A strongly acidic ion-exchange resin was used to extract aluminum from a typical dump leach liquor and from synthetic leach liquors. Aluminum was stripped from resin with a HS04 or NaCl solution. Bench-scale experiments indicate that a single-contact ion exchange is technically feasible, but that the process is limited by the relatively low loading capacity of the resin and the excessive amount of stripping agent required. A further limitation is that significant amounts of magnesium and iron are loaded and stripped along with the aluminum.

Jan 1, 1976

The height of permanent slopes at the Panguna mine of Bougainville Copper Limited will vary from 350 to 950 metres. A few degrees difference in slope angle has a large effect on the ore/waste stripping ratio. Optimum slopes can be achieved if longer batter slopes (exceeding 45m height) are excavated using bulldozers to trim parallel to controlling fracture surfaces. Unnecessary slope flattening by incorporating benches can cost millions of dollars in lost ore. Faults and other major weaknesses, which can result in wedge failure or erodible zones have been treated successfully with shotcrete, rockbolts and cable dowels. To minimize support effort and interference with mine production, early identification and treatment of unstable areas is important.

Jan 1, 1987

By Weijia Guo

With the exploitation of coal resources, a large area of land had been affected by surface subsidence, causing conflicts between man and land to become more conspicuous by the day, affecting the life of general public, and constraining further development of the land. This paper predicts the subsidence areas according to the 10-year mining plan of the Jibei mining district as an example. A plan of environmental management was developed based on sciences and practical economics.

Jan 1, 2006

By R. J. Reynik, F. R. Meeks

IN the classical paper1 of Mehl and Rhines entitled "The Rates of Diffusion in the Alpha Solid Solutions of Copper", the authors state: "It has been mathematically demonstrated that the treatment of the data as though the diffusion were taking place between two flat plates instead of radially in a cylinder has no appreciable effect upon the results. Were the bars of a much smaller diameter, a modification of the analytical treatment would have been required." Unfortunately, the errors in the reported concentrations are much too large to neglect, as shown in the results below. A planar treatment of diffusion data assumes that the reference planes separated by a nominal distance (AX) have identical areas. An adjustment must be made on the concentration data should the successive diffusion planes differ in area. The Mehl-Rhines' diffusion samples were cylindrical with copper electroplated onto copper-based alloys. Successive surface areas through which diffusion occurs are in the ratio ri/r1, where ri is the radial distance between the center of the sample and the center of the i th shell to which the host (alloy) atoms diffuse, and r1 is the radial distance between the center of the sample and the center of the innermost (i = 1) experimentally reported shell from which the alloy atoms diffuse. Hence, ri/r1 (i = 1, ..., n layers) is a dimensionless correction factor to be multiplied by the reported concentration data before planar-data analysis is attempted. In the forty-seven samples reported, the original interface between the copper alloys and the electroplated copper was located at a mean distance of 8.255 mm from the center of the samples. The successive layers, machined off the samples, were approximately 0.0762 mm thick. The distance (xi) at which concentration (ci) was reported was always a distance measured with respect to the original interface, that is, with respect to the fixed distance of 8.255 mm. Hence, the as yet undiscovered Kirkendall Effect was precompensated. The values of ri and r1 are therefore given by ri = 8.255 + xi and Y, = 8.255 + x,. The illustrative table below lists the position xi (mm), ri (mm), the value of ri/r1, the reported concentration (ci) in weight percent (only valid for radial analysis of data), and the corrected concentration [c'i = (ri/r1)ci] in weight percent (only valid for planar analysis of data). Similar tables can be constructed for the remaining forty-six samples. The corrected data can be used to re-evaluate the diffusion coefficients for the reported systems.

Jan 1, 1965

The mining industry continues to faces significant challenges due to increasing resource constraints (quality of ore bodies, water, energy, human resources) and increasing license to operate requirements (safety, health, environment, location) from society, employees and shareholders. Technology advancements and hence research are necessary to ensure that the industry remains viable in this changing environment. Collaborative research is an important part of a company's research portfolio and offers the opportunity for the industry to work on generic issues that it is facing. Obvious benefits include the reduced cost to individual companies by sharing the costs, the opportunity to leverage government funding and the opportunity to conduct longer term projects resulting in skills development (PhD and MSc). Limitations of collaborative research include the reduced focus on company specific issues and the loss of competitive advantage from owning the outcomes of the research. The challenge for researchers and research managers is for them to demonstrate the value derived from longer term, pre-competitive collaborative research. The competitive advantage is not necessarily derived only from the outcomes of the research but rather from the company's ability to direct the research, translate the generic research outcomes to address company specific issues and to implement improvements at its operations. Implementation remains the greatest challenge. In this paper, case studies of selected collaborative research projects are presented to demonstrate key success factors required for implementation of research outcomes. This is an ABSTRACT ONLY. A full-length paper was not prepared for this presentation.

Sep 13, 2010

The Horn Island gold and mineral field produced 194 kilograms of gold in the 4 years subsequent to its discovery in 1894, from an area of shallow workings 1.5 kilometres x 0.5 kilometres. Gold deposits in the adjacent Prince of Wales, Hammond and Possession Islands also drew attention at that time.These islands form part of a Carboniferous sequence of ignimbrites (Torres Strait Volcanics) intruded by the Badu Granite and minor volcanics within the Cape York-Oriomo Ridge. Gold is associated with the epithermal stages of igneous activity. Recent exploration has defined sub-horizontal zones of disseminated gold mineralisation in the sub-surface, as well as reserves in the outcropping sub-vertical structures mined in the past. Released estimates of 170,00 tonnes proven ore and 550,000 probable ore at 4 grams per tonne gold, have been established.Gold is mostly contained in quartz vein stockworks and hydrothermal breccias within the intensely propylitised medium grained granites which form the local host rocks within the coarse grained Badu Granite. Associated vein minerals are sulphides (primarily of lead, zinc and iron) and calcite. Various intrusions of porphyry, aplite and granodiorite occur through the prospect area.

Jan 1, 1986

By W. J. Turbeville

The subject of this discussion is timely. The U.S. phosphate industry is suffering the throes of depression. It's plight is a matter of widespread concern. The future role of the U.S. industry in world markets is of particular interest. If we should prognosticate phosphate supply-demand on the basis of recent history, we would face a puzzling choice of scenario. In 1980, perhaps the best year ever for U.S. phosphate, 54.6 million metric tons of phosphate rock entered the market place. Of this, more than half was exported -- divided almost equally - as rock or phosphate fertilizer. During the last half of 1981 the situation had begun to change.

Jan 1, 1983

By J. Galloway, P. K. Hofmeyr

Obviously all mining operations require much analytical work to be carried out. This starts with exploration, becomes more stringent with the evaluation of a mineralised area and finally becomes on-going when mining operations are under way. All these phases are carried out by geologists, metallurgists and mining engineers. They require analyses to carry out their functions but usually have no involvement in the analyses themselves. Analyses are carried out at commercial laboratories or in-house analytical laboratories. In the past in South Africa the tendency was for the larger mining houses to have their own centralised laboratories for exploration samples with each mine having it?s own laboratory to meet only that mine?s requirements. The centralised laboratory maintains QC functions at the subsidiary laboratories. In other mining areas of the world there has been a strong tendency for all geological analytical requirements, especially for exploration and mining, to be carried out at commercial analytical laboratories. In recent years there has been a tendency for mines in South Africa to move in the same direction. This paper discusses the factors that need to be taken into consideration when a new laboratory is being planned and automation is an option. The planning of the laboratory at the new Langer Heinrich Uranium mine in Namibia is discussed considering these factors. 2.0 REQUIREMENTS OF A MINING ANALYTICAL LABORATORY The purpose and requirements of a mining analytical laboratory are fairly obvious and can be summarised as follows :- 1. All mining operations must have access to analytical facilities, either in-house or commercial 2. The laboratory must be able to handle all the sample types submitted by the mining operation These can be mining, exploration and/or plant samples. They can comprise solids (rocks, bore-cores), slurries and/or liquids.

Jan 1, 2007

By Mr. Peter J. Huck

Recent research has developed procedural control and geophysical test methods that can greatly enhance quality control in rock grouting. Confidence that design objectives will be made In construction requires that grout monitoring efforts be carefully designed and integrated into the overall project. Parameters that should be monitored are identified and documentation/review procedures that permit effective evaluation of the grouting effort are discussed.

Jan 1, 1980

By M. G. Ayat

Although other methods of mineral concentration have been developed over the years, gravity separation remains one of the most efficient and economical for cleaning coal. The concentrating table and the spiral separator are popular devices used for the separation of minerals by exploiting the differences in specific gravities of the product material and the gangue. While the former device has been servicing the coal industry for over 75 years, the latter seems to have not been employed extensively for coal cleaning purposes in this country. As far as coal preparation is concerned, both separatory devices seem to be most efficient for intermediate to fine size fractions. As it stands there exists a great deal of confusion amongst preparation engineers and plant managers as to whether spirals can have a place in the coal industry. If so, whether their come back is the beginning of the end for concentrating tables, or can they be employed along with concentrating tables to contribute toward more efficient cleaning processes resulting in an improvement in the overall economics of the coal preparation industry. This paper examines the efficiency of both systems for coal processing operations as well as the basic principles, operational variables, economics, advantages and disadvantages associated with each unit operation. Attempts have been made to draw conclusions and make recommendations as to which system would be more beneficial for coals of known characteristics.

Jan 1, 1986

By Rowena Anderson

Mining companies are now looking for more effective ways to engage the community in public participation. Consensus-based approaches are becoming the most popularly applied way of achieving meaningful public participation. This paper introduces the principles surrounding consensus-building approaches and the processes for getting them started. The Healthy Communities Movement is one such consensus-based approach that offers a well-established holistic model for conceptualizing a healthy sustainable community. It also highlights the importance of public participation as an essential component of achieving a sustainable community. The paper concludes by illustrating how current company-community relations programs can utilize these models.

May 1, 2002

By S. Agarwal

The mining industry collects a significant amount of operational data. However, gleaning useful information from the terabytes of data is difficult, and not just because of the sheer volume of the data. Therefore, an automated tool was developed at the University of Alaska Fairbanks to go through data and apply very sophisticated statistical and neural network techniques, to identify the data streams that are important to a process. This paper presents results from the tool as applied to SAG mill data from a gold mine. The results were benched against commercial tool. Results indicate that there was little or no loss in performance by automating the very complicated process of neural network modeling. Therefore, the intent of the exercise, to examine if complicated modeling tasks can be automated, was realized.

Jan 1, 2011

By Max Arias Shreiber

El presente texto establece de forma general los aciertos y deficiencias más importantes del Código de Minería de 1950. Para elllo, se revisa las características de la industria minera, productividad, nivel de inversión, sistema de propiedad eminente del Estado sobre los yacimientos mineros, establecido por la Constitución y repetido por los Códigos Civil y Minero.

Sep 1, 1963

Jan 7, 1976

By G. Brackebusch, S. J. Jung

Backfilling techniques are widely used in large-scale underground mines. Massive pillars, which have been left in place for stability, limit mining activity. Backfilling allows safe recovery of the ore remaining in pillars and assures long term stability. In deep mines expected high stress can be relieved with the backfill. Initially, waste rock was used to fill the openings with mixed results. The need to improve safety and reduce costs has prompted the industry to investigate alternatives. Hydraulic filling with Portland cement added has shown considerable promise, but little has been done to define the parameters of design effective system. The purpose of this study is to determine the relationship between backfill and mining components that can be used to effectively design a best-case hydraulic backfill.

Jan 1, 2000

By Klaus Beckmann

Gentlemen : My object reads "Longwall Rapid Advance of Coal Mining in the Federal Republic of Germany". It is true that the percentage of coal obtained in your country from longwall faces, with at present 1.2, is still rather low, but it increased considerably since 1966 with 0.4 %. The coal mines of the Federal Republic of Germany ever used longwall as the classical method of coal getting. All attempts to introduce bord and pillar mining did not lead to any wider application of this method. The principal reasons, for this appear to have been: - the deeper depth of our workings, - the wish to keep working losses as low as possible and to utilize the deposits opened up by deep and therefore expensive shafts to the furthest possible degree, - the dense sequence of seams and the mutual influencing of the working points, - the high number of disturbances in the geologically much stressed deposits, - and the necessary considerations to the protection of the densely built-upon surface.

Jan 1, 1970

By Ronald L. Wiegel

Success has been achieved in developing mathematical models of rod mills, ball mills and recently to a limited extent autogenous grinding mills. There is also considerable activity in the development of mathematical models of various mineral concentration opera¬tions, such as flotation, magnetic separation and electrostatic concentration. However, at present there is a technological gap which hinders the integration of both size reduction and mineral concentration models into an overall process simulation model. This gap exists because size reduction models have been aimed at describing the size of the product and have not dealt with the equally important problem of identifying the product composition in each size fraction. Without this information the concentration model is ineffective. This situation is especially critical in the simulation of the magnetite-taconite beneficiation process, where a portion of the ore is rejected from the process following each stage of size reduction. Consideration has therefore been given to the merging of a size reduction model and a mineral liberation model to permit prediction of mineral composition as a function of size. The results of this integration of size reduction and mineral liberation models are discussed from both theoretical and practical viewpoints using batch grinding data for a magnetite iron formation sample as a demonstration vehicle.

Jan 1, 1975

By E. M. Abraham

The establishment and survival of different grass species and cultivars on various phytotechnic treatments at a limestone quarry was studied. The treatments applied were: a) bare soil, b) bentonite, c) bentonite-straw and d) asphalt-straw. According to the results, significant differences were found among species and cultivars, growing on different treatments as far as plant growth and survival are concerned. The seed germination was higher on bentonite -straw and asphaltic-straw than on bentonite but the plants survival were higher on bentonite. Lolium perenne had higher seed germination rate and better establishment than the other tested species at all treatments. However, the survival rate of Agropyron desertorum and of the cultivars palestina and chrysopigi of Dactylis glomerata was higher than of the other species.

Jan 1, 2007

By R. V. Ramani

In this report, the application and limitation of the various equipment available for surface coal mining are discussed. The correction factors for adjusting equipment performance arising from machine design, material characteristics, and modes of operation are presented. Engineering design, pit layout and equipment selection are discussed with mathematical derivations. Two computer programs (SMCALC and SMRES) have been written to aid in pit design and equipment selection. The Strip Mine Calculation Program (SMCALC) can be used to select the bucket size and reach of shovels and draglines for various pit widths. It will also calculate the number of drills, loading shovels, trucks and bulldozers needed to achieve a production target. The Surface Mine Reclamation Equipment Selector (SMRES) can be used to select the number of bulldozers, scrapers and front-end loaders needed to achieve the desired production.

Jan 1, 1976

By James J. Scott

Workshops were held in eight states during the period from December 12. 1975. through June 25, 1976, under U. S. Bureau of Mines Contract to the University of Missouri-Rolla. The workshops were designed to help define the Bureau's research and development priorities. At each workshop a summary of the current Bureau mine reclamation research was presented which was followed by identification of problems associated with mine land reclamation in the state where the meeting was being held. Discussions included the seriousness of problems locally and how the Bureau could best undertake research to assist the state in solving the problems identified. Participants included representatives of state agencies, educational institutions, and companies involved in surface mining. Attendance at these workshops totaled 201 persons who displayed a wide variety of opinions and ideas as to what should be done In government research and development efforts. A breakdown of these attendees is as follows: 91 state and Federal employees; 69 mine operators, equipment manufacturers and consultants; 33 educators and researchers; and 8 others representing such varied interests as environmental and conservation groups, news media and students .

Jan 1, 1976