Search Documents

By NEFE AEWFW

Changes in the 1980 quantity and value of the sales of various natural abrasives, compared with the data for 1979, were of a mixed nature. Output of garnet and special silica stone products increased in both tonnage and value during the year, while emery and tripoli-type materials production decreased in both tonnage and value. The reported quantity and value of sales of manufactured abrasive material-fused alumina and alumina-zirconia, silicon car-bidet and metallic iron and steel shot and grit-also decreased for 1980. [ ]

Jan 1, 1981

By Richard F. Link, George S. Koch

Advantages and disadvantages of deflecting (wedging) diamond-drill holes to obtain sampling data are compared with the alternative of drilling additional holes. The discussion is based on a statistical analysis of a large set of deflection data from exploratory boreholes in South African gold mines. Representative cost comparisons show the conditions under which deflections are likely to be desirable.

Jan 1, 1969

By R B. Wanty

Historically, most investigations of biogeochemical cycling in acid rock drainage systems involved synoptic sampling over longer time periods (one sample per week or month) or intensive time series studies over a few hours or days. However, many important episodic loading events, such as seasonal meltwater and storm events occur on timescales that are rarely observed by these traditional sampling approaches. Monitoring these transient processes, which may contribute the bulk of the annual metal loading, is essential for accurate assessment in acid rock drainage areas. Recent work also has demonstrated dramatic diel (24 hour cycle) variations in trace metal concentrations in response to diel changes in temperature, pH, oxygen, and photochemical cycling (Brick and Moore, 1996; Nimick et al, in prep). To characterise a system that may respond to diel, seasonal, and episodic events, a monitoring program must sample at a frequency that captures the details of these major forcing events. We developed two novel instruments, the Zn-DigiScan and the DigiSampler to examine low and high frequency temporal changes in acid rock drainage areas. The Zn-DigiScan is a battery powered real time in situ chemical analyser designed for long-term deployments with hourly analyses of Zn. Stream physical parameters (temperature, conductivity, dissolved oxygen, pH, turbidity, etc) were measured every 15 minutes with a water quality sonde. The DigiSampler was developed for the long-term daily sampling of biogeochemically active elements and can take either discrete samples or samples integrated over 24 hours. The DigiSampler collects 2 ml samples in a Teflon coil which are separated by 0.2 ml nitrogen bubbles. The sample coil is returned to lab and the 2 ml samples are diluted 1:10 and analysed for trace metals by ICP-MS. Initial results from a three-day deployment at Fisher Creek, MT, USA have successfully demonstrated the ability of the Zn-DigiScan to record Zn concentrations at levels below 100 ¦g/L. Zinc concentrations measured at 30 minute intervals in Fisher Creek showed a diel cycle with low values of ~25 ¦g/L in the late afternoon and increasing to ~60 ¦g/L by early morning. Zn concentrations were inversely related to temperature and pH, suggesting that temperature and pH dependent adsorption was the main factor controlling diel Zn fluctuations. Initial deployment of the DigiSampler also was successful, revealing diel cycles in Zn, Cu, and Mn. Comparison of trace metal samples collected by the DigiSampler showed good agreement with samples collected by an Isco automated water sampler, demonstrating that the DigiSampler can collect clean samples for trace metal analysis at the low ¦g/L range.

Jan 1, 2003

By D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Jan 1, 1997

By V. P. Keran

Design of the Bajo de la Alumbrera Project started in June 1995 and concentrate production commenced early in the Third Quarter of 1997. The project is situated in North-Western Argentina and is being developed by Minera Alumbrera Limited which is owned by MIM Holdings Limited of Australia (50%), North Limited of Australia (25%) and Rio Algom Limited of Canada (25%). This paper outlines the key features that were incorporated in the design from both process and plant layout perspectives. It explains the background of flowsheet and equipment selection for the plant. A feature of the flowsheet is that it incorporates gravity gold circuits in both primary and regrind circuits for recovery of gold to dore as well as in the copper concentrate product.

Jan 1, 1998

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuOQs) increased with increasing slag basicity, defined by Xcao /XSiO, The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By T. T. Read

"Education is the one thing which is unanimously regarded as valuable. The growing complexity of modern life, with its intricate organization, the manifold kinds of mechanical equipment that are used, and the constantly growing, necessity for the speedy and accurate interchange of information and ideas, make education an asset that constantly increases in value. The number of things that may profitably be known has grown so large that the field of education has been divided, and attention is often directed to only those things that are most immediately valuable. Modern educational facilities are often directed to what may be called corrective, work; the, providing of people with information that they teed in the conduct of their daily lives, but which for various reasons they have not previously had facilities for acquiring. The value of special education in the industrial world has been so thoroughly demonstrated that far-seeing managers of mining enterprises are always interested in the educational facilities existing in the community where their work is carried on.The educational facilities of a modern community may be classified in several ways. They may be divided into;1. Facilities for general education, for the purpose of increasing the whole field of knowledge of the student.2. Facilities for special education, which are intended to remedy a specific defect, or to give proficiency in some special field. This may be divided as follows;a. Training for work, intended to fit an employee to adequately perform the task assigned to him, this ranges from brief instruction by a foreman or fellow-worker up to definite training courses in which the employee dose nothing but study for a period of several weeks or months, being paid during this period a wage that may range from a nominal amount up to practically full time salary. The student's educational preparation may already be fairly advanced. Some of the manufacturers of electric machinery maintain, a school similar to that just described for graduates of engineering colleges. In other cases the only pre-requisite may be a common school education, as in the schools for operators, maintained by the telephone companies."

Apr 1, 1920

By Toshiaki Tsuru, Takeshi Ohgai, Hisaaki Fukushima, Shigeo Kobayashi, Tetsuya Akiyama

"Electrodeposition behavior of Zn-Cr alloys from the methanol baths was investigated. In the methanol baths of low Cr3+ concentration, Cr (III) compound was incorporated in the deposits and no lusfrous Zn-Cr alloys was deposited. However, Cr was existed as metallic state in the deposits obtained from the baths of higher Cr3+ concentration. With an increase in water content in the baths, the chemical state of Cr in the deposits changed from metallic to trivalent state. Under the condition that metallic Cr can be electrodeposited, Zn deposition was significantly polarized to the potential of Cr deposition.INTRODUCTIONAn attention has been paid to Zn-Cr alloy plated steel sheet because of its excellent properties for body panels of automobile and electrical appliances [1]-[4]. This plating process can be operated using the sulfate solutions containing Cr3+ ion [1] - [6].In decorative single Cr plating, on the other hand, many attempts have been made to electroplate Cr from trivalent electrolytes, which is motived by environmental deficiencies of the presently used hexavalent process [7]. [8]. However, it has been reported that in the aqueous solutions the behavior of the electroreduction of 0 3+ is atypical due to the complicated nature of the chemistry and electrochemistry of cr3+ species [9]-[11]. Even in Zn-Cr alloy plating, it is difficult to codeposit metallic Cr with Zn in simple sulfate electrolytes [l]-[4], [12]. Therefore, it can be expected that the electrodeposition behaviors of Zn-Cr alloys as well as Cr are significantly changed when the electrodeposition is conducted in non-aqueous plating solutions.In this study, the electrodeposition of Zn-Cr alloy was conducted from methanol solutions to clarify the electroreduction mechanism of Cr3·-Cr0 in the alloy deposition process."

Jan 1, 2000

By F. J. Chernosky

In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these papers have attempted to correlate the intrinsic chemical and physical properties of the reagents or reagent groups to the floatability of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, (1) the yields obtained, (2) the ash levels obtained, and (3) the reagent cost relating to these results.

Jan 1, 1962

By J. Salazar

This paper presents a dynamic simulator of the semi-autogenous grinding operation deduced from first principles (non-stationary population balances) coupled to a Model-Based Real-Time Optimization (MBRTO) system to study optimizing strategies for an industrial semi-autogenous mill using genetic algorithms. For the design of the MBRTO both a validated first-principle steady-state model adapted on-line and a dynamic model were used to study the transient effect. The objective function considered is to maximize the ore throughput or the fine-product rate by changing the power-draw. For these purposes, these two performance indexes were introduced as fitness functions in the genetic algorithms. The three decision variables used were the ore feed rate, the water feed rate and the mill rotating velocity. The optimization problem was solved using a classical genetic algorithm with constant population. Constraints in the power draw and the filling level were handled by assigning a penalty function to the fitness function. Simulation results using industrial data for a large 1800 t/h copper-ore mill show the effectiveness of the system in finding the optimum controller set-points as a function of the process-operating constraints; mainly maximum ore feed rate, power draw and filling level. Starting from non- optimum conditions, the optimizer is able to improve the global performance index by 50% relative to a base case.

Jan 1, 2007

By W. L. Cornell

Bulk sulfide concentrate produced from Missouri Pb ore concentrator tailings must be reground to liberate sulfide values for subsequent sepa-ration. Studies to determine grinding parameters for optimum liberation were carried out using optical microscopy coupled with image analysis. The major sulfide phases present in the ground mineral particulates are marca-site, pyrite, sphalerite, galena, chalcopyrite, siegenite. and bravoite. Results showed that the base metal minerals were liberated by grinding to 74 micrometers (200 mesh), but the siegenite and bravoite required grinding to 20 micrometers or less to achieve liberation. Both the experimental method and results are presented.

Jan 1, 1987

By Carlos A. Jaramillo, Seng Hing Ngu

"The Murum Hydroelectric Project is a 944-MW development consisting of a 145 meter high RCC dam, two 2660 meter long, 9 meter excavated diameter upper pressure tunnels, surge shafts, two 950 meter long 7 even meter OD penstock tunnels and a surface powerhouse. The project is located in the eastern section of the State of Sarawak, Malaysia, about 200 kilometer from Bintulu, in the Rajang Fold-Thrust Belt, an Upper Cretaceous to Upper Eocene fold and thrust belt that extends under most of Sarawak. The Belaga Formation consists of a thick sequence of deep marine sediments currently appearing as steeply dipping strata of thin to thick bedded, fine to medium grained sandstone interbedded with argillaceous rocks, resulting on a “Flysch” type geologic environment. The project pressure tunnels were excavated perpendicularly to these strata resulting on frequent change on rock conditions and behavior, and required rock support. This paper describes the characterization of the rock mass, design of rock support, and incidents during construction. Particularly interesting were convergence issues in Tunnel 1 resulting from Tunnel 2 excavation. INTRODUCTION The Murum Hydroelectric Project is located in the eastern section of the State of Sarawak, Malaysia, about 200 kilometers from Bintulu, and upstream of the Bakun Hydroelectric Project. The project consists of a 145 meter high RCC dam, a 50 meter high intake tower, two nine meter OD and 2660 meter long upper pressure tunnels, two nine meter OD and 175 meter long vertical shafts, two 25 meter diameter and 80 meter deep surge tanks, two seven meter OD and 950 meter long penstock tunnels and four seven meter OD and 50 meter long branch tunnels, two 8 meter diameter to 3.4 meter diameter and 1400 meter long penstocks installed within the shafts, penstock tunnels and branch tunnels ending in a powerhouse with 944 MW installed capacity. LAYOUT OF THE WATERWAY TUNNELS The two waterways tunnels are basically parallel as shown in Figure 1, with each tunnel supplying water to two units in the powerhouse. The tunnels start separated 25 meters center to center, but 250 meter from the intake the separation increases to 35 meters. The tunnels are lined with reinforced concrete until they reach the surge shafts and steel lined from there to the powerhouse. The tunnel profile is shown in Figure 2."

Jan 1, 2016

By R. Y. Wan, S. L. Chryssoulis

"Gold associations were established in a·biooxidized, chlorinated CIL residue assaying 0.02 oz Ault and in a biooxidized thiosulfate leach residue assaying 0.01 oz Au/t. A detailed mineralogical study involved: assays of screened fractions; light microscopy; ion probe microanalysis to quantify 'invisible' gold in sulfide minerals; proton probe microanalysis to detect and quantify preg-robbed gold. In the CIL residue, most of the gold is preg-robbed (71 %). In the thiosulfate leach residue, gold occurs mainly as submicroscopic disseminations in microcrystalline quartz (chert). In both residues, the 'invisible' gold in pyrite accounts for a minor fraction of the gold assay. Quantitative determination of the gold occurrence in the two residue samples established conclusively that gold adsorption on carbonaceous matter in the thiosulfate leach is of minor importance.Acknowledgement: published with permission of Newmont Gold Company."

Jan 1, 1997

By José De La Cruz

Para la construcción del dique de arranque de una planta concentradora es importante considerar la ingeniería y diseño del mismo -en tanto debe realizarse un diseño adecuado y así evitar problemas a largo plazo en la estabilidad de la presa de relaves. En ese sentido, el presente texto señala los costos, calidad y estabilidad del diseño de presas de relaves a través del proyecto de Toromocho S.A, perteneciente a la minera Chinalco, cuyo dique de arranque es CFRD (Concrete Face Rock File Design), método aguas abajo. La modalidad de este método permite diseños con un menor empleo de volúmenes de material de cantera que es aplicable en aquellas zonas con baja producción de material constructivo.

Dec 1, 2014

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuO0.5) increased with increasing slag basicity, defined by XCao/Xsio2 The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By R. S. Kasper

This paper reviews the procedure used to quantify the conveyor frictional resistance on a 3.9 km (2.4 mile) long overland conveyor belt. Field torque measurements of the three drives were used to help fine tune a computer simulation of the conveyor. This enabled the prediction of the effect on various conveyor components that cold temperatures will have on increasing the throughput tonnage.

Jan 1, 1995

By Lan Li, Izaak Williamson

"The efficient separation and storage of CO2 from power plant flue gases can reduce the amount of CO2 released into the atmosphere and mitigate global warming. Potential candidates for industrial applications are solid sorbent materials. Crucial factors to control the efficiency of porous sorbent materials include the framework and pore structure, and the chemical and physical reactivity of CO2 within the pores. Computational modeling approaches, based on density functional theory (DFT) and van der Waals-DFT, have been applied to nanoporous solid – manganese dioxide a-MnO2. We found that the types and charges of cations as dopants in the a-MnO2 and the concentration of CO2 influence the structural features of a-MnO2, which control its CO2 selectivity performance within the flue gases.IntroductionCarbon capture and storage is a technique to separate large quantities of CO2 from power plant flue gases before being released into the atmosphere. Porous solids are a potential candidate as sorbents to “trap” CO2 through chemical or physical adsorption on their porous surfaces[1]. Such separation efficiency is determined by the size and shape of its pores and by the interaction between the porous surface and the gas adsorbates. The incorporation of cations into the pore can act as a means of structural support and alter the pore diameter to be comparable to the kinetic diameter of the gas adsorbate, such as CO2.A porous solid of particular interest for CCS is manganese dioxide a-MnO2, an octahedral molecular sieve (OMS) composed of edge-sharing MnO6 octahedra that are linked into a nanoporous framework[2]. The framework consists of (1×1) and (2×2) tunnels, referred to as OMS-2. Due to the larger tunnel size, cations and gas adsorbates prefer to reside along the (2×2) tunnel axis of the OMS-2. As seen in Figure 1, a potassium cation K+ is located in the (2×2) tunnel, known as cryptomelane-type MnO2. Its pore diameter of ~ 4.6 Å gives it a good CO2 selectivity performance, because the diameter is comparable to the kinetic diameter of 3.3 Å for CO2[3]. Alternatively, replacing potassium K+ with other cations, e.g. barium Ba2+, sodium Na+ or lithium Li+, in the OMS-2 tunnel is of great research interest, due to the effects of their concentrations, types and charges on the CO2 selectivity efficiency and sorption hysteresis phenomenon[2,4]."

Jan 1, 2014

By Wei Wei

Mining induced ground movement and/or stress redistribution could cause ground instability issues. This is particularly true when the extraction of large stopes is done with one or two large production blasts. Often enough, it is the nearby mine development like haulage drifts and cross cuts that are influenced the most by production blasts. Proper and timely mitigation of ground control issues due to stress redistribution is required. This is usually done by drift rehabilitation involving the installation of secondary support system in the affected areas of the mine development which include; slashing, wire mesh, and in some cases the use of shotcrete liners. It is imperative that such rehabilitation be implemented to the mine infrastructure in a timely manner in order to avoid aggravated ground control problems and production delays. If the real time performance of the support system is captured, it would be possible to determine the timing for rehabilitation job. Birchtree Mine in Thompson, at the Vale Manitoba Operation, has begun mining the 84 Deep Orebody. One of the identified risks is the stability of the crusher room under mining induced stress redistribution. It is proposed to use the U-Cell technology to monitor the primary support system performance (rebar bolts and extension bolts) and monitor the real time performances of the bolt axial loads. The U-Cell technology is a 7-inch long, coupler load cell that is screwed onto the threaded portion of a rock bolt prior to installation. Rehabilitation in the vicinity of the crusher area where U-Cells are installed is recommended when the bolts have reached 70% of their yielding capacity. Catastrophic ground failure can be avoided by adding secondary support in a timely fashion. This paper presents a case study at Birchtree Mine in Thompson Manitoba, where the performance of primary ground support system is monitored and recorded during production.

Jun 1, 2012

By J. Bai, C. Zang, W. Yuan, L. Zhuang

"This study evaluates the efficiency of using mechanochemical reduction to assist the extraction of zinc from zinc ferrites by alkaline leaching. The transition of zinc ferrite into a metastable state after mechanochemical reduction with metallic iron contributes to the ready dissolution of zinc from the activated zinc ferrites in alkaline solution. Zinc ferrites were mechanochemically reduced under conditions of Fe:ZnFe2O4 mole ratio of 2:1, using 5 mm diameter stainless steel balls as the activation medium at a mass ratio of balls to raw materials of 25:1. Subsequent leaching in 6 mol/L NaOH solution at 90°C resulted in more than 70% Zn extraction. These results may be used to further develop a hydrometallurgical process for recovering zinc from zinc ferrites in alkaline solution.IntroductionZinc is an important nonferrous metal required for various applications in batteries, solder, dielectric materials, and piezoelectric materials. High-grade, easily concentrated ores are becoming scarcer: to meet world demands for zinc, it is necessary to develop economical and environmentally safe metallurgical technologies that use secondary materials such as leach residues of roasted zinc concentrates and electric arc furnace dusts. The zinc in the majority of these wastes occurs in the form of zinc ferrite (franklinite, ZnFe2O4), which is very stable and insoluble in most acidic and alkaline solutions (Langova and Matysek, 2009; Youcai and Stanforth, 2000).Several pyrometallurgical and hydrometallurgical processes (Jankovi et al., 2014; Langova and Matysek, 2010; Morcali et al., 2012; Shawabkeh, 2010) have been proposed for the treatment of zinc ferrites. Pyrometallurgical methods are costly owing to high energy consumption and their emissions of toxic gases are considered an environmental problem; hydrometallurgical methods are preferred for process economy and environmental reasons (Copur et al., 2004)."

Jan 1, 2016

By Irina Melekestseva, Beltenev. Victor, Victor Ivanov

"One of the major problems discussed over the last years is a possibility of mining of seafloor massive sulfide deposits. In spite of the pessimistic points of view on their commercial development, they are still of great interest and continue to be studied (Hannington et al., 2011). Recently, Barriga (2012) paid special attention to the underestimated amount of massive sulfide hydrothermal fields and pointed to the importance of the buried fields and subseafloor mineralization.This study examines the geochemistry of seafloor and subseafloor precipitates collected at the Peterburgskoe (19°52´ N) and Irinovskoe (13°20´ N) hydrothermal fields (MAR) during the 34th cruise of the R/V Professor Logatchev in 2011. These fields were discovered by the Polar Marine Geosurvey Expedition in 2010 and 2011, respectively (Shilov et al., 2011; Beltenev et al., 2012). The Peterburgskoe field, associated with basalts, is located 16 km west of the main rift valley at the depth of 2800-3100 m at the junction of a large non-transform discontinuity with the second rift ridge parallel to the rift valley. The Irinovskoe field occurs at depths of 2700-2850 m and has a northwestern satellite sulfide site, both confined to an oceanic core complex (MacLeod et al., 2009), which includes mafic and ultramafic rocks. The details of geological structure of the fields may be found in the relevant papers.Diverse samples were collected from the hydrothermal fields: seafloor massive sulfides, Fe-hydroxide crusts, SiO2-rich sulfide-bearing precipitates, and subseafloor mineralized rocks (Melekestseva et al., 2014a). Massive sulfides may be subdivided on the Fe-rich and Cu-rich types. The marcasite-pyrite, pyrite, hydroxide-marcasite, and chalcopyrite-pyrite (Fe-rich) mineral types are dominant in the Peterburgskoe field at lesser amounts of sphalerite-hydroxide-chalcopyrite and pyrite-covellite-chalcopyrite (Cu-rich) massive sulfides. The mineralized sulfide-talc-carbonate-chlorite, chlorite-sulfide-quartz, and hematite-sulfide-quartz rocks host stringer-disseminated sulfides including chalcopyrite, covellite, and pyrite."

Sep 1, 2014