Search Documents

By H Lieberwirth, M Pfeifer, F Heinicke

HPGRs (high pressure grinding rolls) have been developed within the last decades for energy efficient processing of a wide variety of ores. Special interest has been raised by projects increasing the capacities of processing plants by installing HPGRs prior to ball mills. Bond ball mill tests have been used for decades as a base for ball mill dimensioning in mineral circuits. For final CAPEXOPEX considerations of the processing circuit, one key question is about the level of grinding energy split between HPGR and downstream grinding stages. This is especially interesting if the downstream process comprises multiple grinding stages combined with separation steps. The paper presents investigations on grinding energy consumption, size distribution and microfracturing of HPGR products, which affect the efficiency of the whole comminution and sorting process.

Aug 24, 2022

By Keith MacKay, John Carter, David Siddle, Fernando Faminia

"The River Green Residential development, is located in the municipality of Richmond, BC adjacent to the Fraser River. Ground conditions at the site consisted of medium to fine grained alluvial sands and a high groundwater elevation. A temporary low permeability retaining wall was required in order to facilitate the construction of an underground parking structure without inducing settlement of adjacent structures, which include the Richmond Olympic Oval; part of the legacy of the Vancouver 2010 Winter Olympics. Golder Associates Ltd. and GeoPacific Consultants Ltd. utilized Cutter Soil Mixing (CSM) technology to enable construction of a continuous combined low permeability cut-off and retaining wall around the perimeter of the property. The 350m long wall was keyed into marine clay at a depth of 28m below ground surface, and contained H-Pile reinforcement installed at regular intervals. The CSM technology provided many benefits for this project, allowing the combined cut-off and retaining wall to be constructed within a very narrow footprint (650mm width). The low noise impact and near vibration free construction of the CSM equipment provided minimal inconvenience to nearby stakeholders during construction. To reduce dewatering volumes during excavation and prevent significant water-table drawdown the Hydraulic Conductivity requirements for the wall were 1 x 10-7 cm/s or less. Project specifications called for a different strength requirement for upper and lower portions of the wall. The top 13 meters of the wall required an Unconfined Compressive Strength (UCS) of 4MPa to act as a retaining and cut-off wall, whereas the bottom 15 meters of the wall required a UCS of only 0.5 MPa to act only as a cut-off wall. Wet-grab and core samples were obtained from the panels to confirm the UCS and Hydraulic Conductivity specifications were met.INTRODUCTIONGolder Construction Inc. and GeoPacific Consultants Ltd. conducted the design and construction of a deep soil mixed cut-off and retaining wall system. The “dry-box” solution was used to surround the excavation of an underground parkade and prevent flows of groundwater into the excavation."

Jan 1, 2016

By Chuanyu Feng

In this paper, a load-based micro-indentation technique suitable for field applications was developed. This technique bears the same theoretical background as traditional load-depth sensing indentation, and does not need any direct measurement of indentation depth or contact area. The removal of this requirement will reduce much of the cost associated with traditional instrumented indentation. To demonstrate the feasibility, a portable indentation system suitable for online material characterization was developed. Design issues of the portable unit were discussed and preliminary results using the portable unit were also presented.

Jan 1, 2009

By J. M. Hird

By blending phosphogypsum with thickened mill clays, Texasgulf has successfully resolved the problems of gypsum disposal and reclamation of mined-over areas. In the process, clays are thickened to 10% solids through high rate thickeners, mixed with gypsum from a drained gypsum pile (75%) and a direct discharge from belt filters (25%), then pumped to mined-over areas. The blending of clays and the low pH gypsum yield a mixture with a pH of about 7. Dewatering is rapid to 40-45% solids within 3 months. The material spreads with very shallow slopes and within a year desiccation by high flotation ditching equipment is possible. The artificial soil is classified as a silty loam in texture, lacking only in nitrogenous nutrients. The soil material has proven to support many field crops including small grain, corn, alfalfa, and grasses. Sycamore, green ash, sweetgum and bald cypress have done well in 3 years of growth. The nitrogen source for tree growth will be made up through an alfalfa cover.

Jan 1, 1993

The performance of the Australian Mining Industry over the past 10 years using key indicators of production, revenue, aftertax return investment, together with key cost elements, market changes and ore reserves is briefly reviewed. The elements of competitiveness are discussed forthe industry and the effects of Government charges and policies relating to existing operations are outlined. There is a demonstrated need for improvements in competitiveness in direct and indirect costs and for improved access to resources for the mining industry to continue to grow and add to Australia's economic growth.

Jan 1, 1987

By Maja Franjic, Ian Tolliday, Chris Collins, James Wiltshire

Ammonium Nitrate Emulsions (ANE) are a large segment of the explosives market for the mining industry. These emulsions are generally designed to be very stable but when breakdown does occur, removal of the resulting thick, crystallized material can be difficult, hazardous, time consuming and costly. A heavily crystallized emulsion cannot be pumped, so manual removal often becomes necessary. Buildup of semi-solid layers of crystallized emulsion can occur in bulk storage tanks or in truck compartments. In these situations, a manual cleanup involving hazardous confined-space entry and a significant amount of downtime is usually required. Once the crystallized emulsion is removed from the equipment, there is very expensive disposal of the resultant waste via a licensed trade-waste company. A much more desirable solution for dealing with waste emulsion is to completely break the emulsion, allowing the oxidizer and fuel phases to separate into two distinct layers. These layers would then be readily pumpable and could be disposed of much more economically. It may even be possible that the separated oxidizer phase could be repurposed as fertilizer and the fuel phase could be used to manufacture granular ANFO explosives. There are some existing products on the market for breaking emulsion explosives, but these generally need a high degree of mixing into the emulsion to achieve adequate breakdown. The aim of this study was to identify surfactants systems (demulsifiers) capable of effectively breaking a range of waste emulsions with minimized agitation. This paper describes the development and performance testing of novel demulsifier products. The test work involved a comprehensive series of laboratory screening tests, where the demulsifier formulations were optimized. A highly efficient formulation was identified, and field trials were conducted on real world, full-scale waste emulsions. Results will be presented that demonstrate a viable solution for the disposal, and potential re-use, of waste ANE in the explosives industry.

Jan 21, 2025

By Paul Hewitt, Aaron Rastall

The New South Wales South Coast rail corridor is key infrastructure for both freight and passenger transport. Geomorphological and geological evidence suggests that land instability has been widespread throughout sections of the rail corridor, long before the first documented record of landslide activity in 1879. Major landslides occurred along a 25-km length of the South Coast Railway connecting Sydney and Wollongong because of significant rainfall events of the late 1980s. Since this time, several sites have been identified as subject to instability and treated progressively under a risk priority and safety management system. Two such sites comprise a station footbridge and overhead wiring structure (OHWS), both founded on high embankments overlying colluvial materials resulting in the structures’ potential movement and associated stability concerns. This paper presents these two sites as case studies, and discusses the project geology, geotechnical models developed, interpretation of monitoring data, and successful remediation of the rail structures using sleeved bored piles. The sleeved pile system was used to isolate bored piles, which separated the bridge foundations and OHWS from the moving soil mass to ensure the piles can carry the rail structure loads, unaffected by downslope soil movements.

Nov 1, 2022

By C Mark, Z Agioutantis

This paper presents an empirical design methodology that is based on successful US roof support systems using both primary and secondary support in coal mining entries and intersections. The recent nationwide dramatic reduction of roof fall rates, especially in areas with weaker roof, can be directly correlated to the effectiveness of the roof support systems. A large database of roof fall histories at several mines is used to define the approximate boundaries of three modes of roof support with respect to roof strength as classified by the Coal Mine Roof Rating (CMRR) and in situ vertical stress as indicated by the depth of cover. These roof support classifications are: • Suspension, where roof bolts mainly provide skin control for strong roof. • Beam building or reinforcement, where a roof of moderate strength can be supported by roof bolts only. • Supplemental (secondary) support, where the primary support by roof bolts may be augmented by several secondary support systems, eg cable bolts, trusses, additional roof bolts or standing supports. The Primary Support Rating index (PSUP) captures the capacity of the primary roof bolt system as a function of the actually implemented roof control plan, ie roof bolt length, roof bolt density, and roof bolt capacity, while it does not consider the type of bolt. The actual PSUP value is compared against a suggested PSUP value derived from statistical analysis of US case histories. Where secondary support is indicated, the expected rock load determines the necessary capacity of the secondary support system. A new (free) software package, Analysis of Mine Roof Support (AMRS), implements the design methodology and also allows comparison with other international indices such as the Reinforcement Density Index (RDI), the PRSUP, etc.

Nov 29, 2022

By Yazen Khasawneh, Yao Zhang

Upgrading and maintenance programs were proposed at a power generating plant in Indiana. To perform construction activities associated with the proposed upgrading and maintenance, a LR11350 crawler crane with a dead load of 1,500 ton was required in the vicinity of existing plant structures. The contact pressure from the crane tracks for the heaviest lift, maximum reach and angle (worst loading condition) were estimated by the rigging engineer to be on the order of 84 psi. Several concerns were raised regarding the total and differential settlements while the crane is in operation and the induced stresses on existing underground utilities due to crane loads. Three-dimensional finite element simulations were conducted using hardening soil model for the subsurface soils and elastic model for the other structural elements (underground utilities and crane mats) to optimize the configuration of the proposed crane foundation. It was found 1-foot thick engineered steel mats underlain by a 1.5-foot thick crushed stone pad will provide enough support to the crane. It will also control the settlement to the allowable limit and maintain the stresses in the underground utilities within tolerance. INTRODUCTION A LR11350 heavy lift crawler crane was proposed as part of an upgrade program at an existing power plant in the state of Indiana. The proposed crane will be sitting on an open ground in the vicinity of existing plant facilities, with multiple underground utilities going beneath the proposed footprint of the new crane pad. The existing utilities are of diverse kinds, including sanitary sewer corrugated metal pipes, electrical conduits and variable steel water/oil drain pipes. The safety and functionality of these underground utilities are critical to maintain the proper operation of the power plant. Therefore, the design of the new crane pad foundation system is of essential to control the ground settlement and the imposed stresses to the existing utilities (Davie et al., 1998, Scott 2017). To ensure all utility locations and depths are identified, the proposed footprint was thoroughly surveyed. Information in regard to each identified utility was provided by the owner. Subsurface explorations were conducted using geotechnical soil borings and soundings to evaluate the ground conditions and generate soil profiles. Numerical simulation and analysis utilizing finite element method were performed to design the crane pad foundation system and evaluate the responses of the utilities. This paper summarizes project information, geotechnical conditions and then focuses on the finite element analysis in assisting the design of crane pad and the utilities evaluation.

Jan 1, 2019

By M S. Powell, M P. Bueno

The commonly used SAB, SABC and run-of-mine (ROM) ball mill circuits can achieve high throughputs with good operating stability. However, these circuits consume a substantial amount of grinding media, which can have a substantial impact on the OPEX and the æcarbon footprintÆ, specifically when viewed as an æembodiedÆ energy input. On the other hand, fully autogenous (AG) circuits can operate at much lower operating costs, but with limited throughput. The control of AG mills, fed by ores with hard and soft components, can also be challenging, due to the sensitivity of the mill to the ratio of hard to soft components.In this paper, a multi-component modelling approach was used to demonstrate that the harder component should be used as grinding media, and its use should be kept to a minimum to avoid reduction in the mill throughput. There is an optimal blend of hard to soft, and any optimal blending condition is both ore-dependent and mill-specific. Establishing this blend is challenging, and consequently discourages the use of autogenous mills. The new modelling approach addresses this challenge by providing a quantitative prediction of the influence of blending soft and hard components in a mill. This prediction can then be used to establish the required blend for maintaining a stable and efficient operation in autogenous grinding mode.CITATION:Bueno, M P and Powell, M S, 2012. How to use hard ore components as grinding media, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 31-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Stefan Wahlund, Tom Adams, Mats Söder, Zhi Zhang

By applying high-end rolls with utmost performance and superior surface quality, hot strip mills can be further optimized. Operations in the mill have been also waiting for improved roll solutions that can minimize required roll changes which impact production efficiency. Limitations are usually due to the low performance and surface degradation of the rolls in the late finishing stands (F5 – F7). VICTURATM is the most recent developed grade for rolls utilized in the late finishing stand at Union Electric Åkers (UEÅ). These rolls have been tested and applied in mills all over the world. A significant improvement over the enhanced ICDP rolls has been observed. Hot strip mills are realizing improved operating efficiency and Total Cost of Ownership (TCO) through the transition of their entire roll inventories to these break-through products.

Oct 1, 2019

By Giovanna Lorena Carneiro Costa, Ana Paula Silva, Amarildo Ferreira, Vinícius Freitas Paixão

Uma maneira de detectar macro inclusões é através de testes ultrassônicos, embora a análise e a interpretação dos resultados dos testes sejam difíceis de entender. Com os resultados da inspeção, temos informações sobre a localização das macro inclusões e, portanto, sua distribuição ao longo do material. No entanto, estabelecer critérios para classificar o material quanto à sua pureza tem sido uma tarefa difícil. O presente trabalho visa estabelecer uma ferramenta de análise de dados a ser utilizada para controle de qualidade de materiais. Os resultados mostram uma viabilidade estatística e metalúrgica de aplicar este modelo analítico para avaliar o nível de pureza dos aços laminados a quente.

Mar 1, 2019

By Daniel Suarez

Over the last few years the mining industry has continuously been facing increases in capital and operating costs for new projects; plant expansions and also significant increases in the operating costs of existing plants. To counteract such trend the industry is seeking technologies such as the Vertimill as an option to lower the operating costs of grinding circuits. The benefits the Vertimill offers in terms of lower energy consumption and lower media consumption are well established and documented; such benefits can significantly improve the viability of a new project, plant expansions or upgrading grinding mills that need to be replaced. The paper briefly describes the operation of the Vertimill, recent regrind applications in processing Iron ores where the impact of lower energy and grinding media consumption is very significant because of the large tonnages involved, and also applications as a tertiary and secondary grinding stages of grinding circuits. The paper also highlight the expected role the Vertimill can play in secondary applications and the expected impact on the overall economics of the project.

Aug 1, 2018

By Leonardo Carneiro Andrade

O desenvolvimento de materiais renováveis e biodegradáveis é uma vertente que almeja a diminuição dos custos e dos impactos ambientais. Nesse âmbito, o presente trabalho visa o desenvolvimento de novos materiais, fabricados com fibras vegetais e que possam substituir outros que são derivados do petróleo. Fibras vegetais foram utilizadas e devidamente modificadas por mercerização e acetilação com o intuito de produzir materiais com compatibilidade química. Foram obtidos, nesse trabalho, compósitos de polietileno reciclado reforçados com fibras de sisal[1]. Utilizamos a ferramenta estatística denominada distribuição de Weibull, para prever as falhas mecânicas dos sistemas estudados. Foi possível observarmos que o compósito resultante teve uma melhora relativa em suas propriedades mecânicas, o que pôde ser comprovado por meio dos ensaios de tração. A distribuição de Weibull foi uma ferramenta que produziu resultados de acordo com os esperados, comprovando a melhoria de propriedades mecânicas do material.

Oct 30, 2017

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By D Readett

The most critical variable in the successful establishment of the Murrin Murrin Heap Leach plant was the effective agglomeration of the Ni laterite ore. This paper describes the test work undertaken to establish the key agglomeration parameters including state of the art testing and analysis procedures. These parameters were then utilised to establish the key design and operational concepts for the world’s first commercial scale Ni laterite heap leach. Following the technical and economic success of the operation, the actual operational data is compared back to the original test work data.

Aug 8, 2011

By Bobby Michael (Mike) Roberts, G. M. (Mike) Bernard, Ronald R. Kelly

This paper describes Cananea's successful implementation of the world's first mobile high angle conveyor (MHAC™) to achieve multiple-lift stacking of their primary crushed (2,500 mtph) low-grade ore. The mobile high angle conveyor answered Cananea's needs to stack a second lift, 30-meter high, on their Quebalix I pad. The mobile high angle conveyor is a custom unit that was designed by Terra Nova Technologies (TNT) in conjunction with Continental Conveyor and Equipment Company (CCE's 100th HAC). The stacking system expansion project also includes a rail mounted tripper on the existing overland conveyor and a custom designed "corridor conveyor" to build the corridor for the upper mobile HAC tracks and tail of the existing mobile stacking conveyor. Mexicana de Cananea, part of Grupo Mexico, is a large copper producer in Sonora Mexico and has been in operation continuously for over 100 years.

Jan 1, 2002

By T. Peter Philip, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Douglas N. Halbe

Scarcely a month goes by that I or someone else at Newmont Mining or Newmont Gold isn't asked to give a talk on the topic I was asked to discuss today. Investors, financial analysts, geologists, metallurgists, even our government--everybody wants to know what the future holds for gold mining. Well, you're not going to get exactly what you asked for. Today, I'm prepared to focus primarily not on what the future will bring to us, but rather on what the future will demand from us. More than that, I cannot undertake because it isn't within my scope to predict how wise and resourceful everyone in our industry will be in the future. What our future will hold, as I see it, will depend on our--and our colleagues'-- responses to these very real demands. Three critical issues stand out in my mind as to what the future will demand of us in the gold mining industry. And these demands will be for: 1. The very greatest of technical expertise and innovation. 2. The highest order of environmental sensitivity and timely accommodation. 3. Planning, planning and more planning. All of these flow inexorably today from the traditional objective of any mining company--or any company in any business, and that is, to make money. Nothing as I see it, should be undertaken by a geologist, metallurgist or even an environmental department, unless the exercises will enhance profits; and nothing may be ignored which can have consequent damage to the bottom line. Thus, the three issues I've listed for you subordinate themselves to the objective of making money, although at least in the environmental area, it might seem to some that we can only incur additional costs without even a dollar-for-dollar return. I hope to disabuse you today of any such out-of-date notion. Let's tackle the first issue-- Technical Expertise and Innovation. Newmont Gold Company this year is celebrating its 25th anniversary of successful and profitable operations on the Carlin Trend. Carlin in 1961, which is when exploration began on the "Trend" by Newmont, actually may share a lot of similarities with Carlin today. They didn't then know where the gold was and, if they found it, they had one hell of a challenge mining and processing ore at a profit because gold was selling at only $35 an ounce. Today, we know where the current reserves are. But we don't know where our future reserves lie. Furthermore, we don't know exactly how we're going to mine them, and, as everyone here knows too well, we don't know what the optimum metallurgical treatment is, even if we can find and mine them. And all that despite the abundant level of modern experience and skills within the current generation of mining companies, and the fact that, even taking inflation into account, gold sells at a higher price today than in 1965 when Carlin began operations. But, of course, I'm telling you what you already know.

Jan 1, 1990

By Dion Weatherley, Raúl Castro, Pablo Cid, René Gómez

In underground mining, hang-ups due to coarse fragmentation are frequently observed in drawpoints, drawbells, and ore passes during ore draw. Hang-ups can often require operational interference and hang-up removal activities. Drawpoint and drawbell design has been shown in some studies to influence hang-ups; however, the full extent of this influence remains open to question. In this study, the discrete element method was used to analyze the effect of hang-ups on three distinct drawbell geometries: the Drawer type, Circular type, and El Teniente type. The drawer type was used as the base case given that data was available from a physical model in which hang-ups were studied. The drawer type base case data was then used to calibrate our numerical model. Results show that the El Teniente drawbell geometry sustained 13% more hang-up events as compared with the base case, while the circular drawbell geometry had 16% fewer hang-up events than the base case. From this study, it can be concluded that fewer hang-up events will occur with a rounded drawbell geometry.

Apr 11, 2023

By M. A. Kader, M. A. Islam, P. J. Hazell, M. Saadatfar, J. P. Escobedo, A. D. Brown

The dynamic pore collapse mechanisms and energy absorption capacity of closed-cell aluminium foams subjected to low velocity impacts have been investigated. Impact experiments were carried out using an instrumented drop-tower with two impactor geometries: a 50 mm square flat steel impactor to investigate pore collapse mechanisms and a 20 mm diameter hemispherical steel impactortostudy indentation resistance.X-ray computedtomography was utilized to generate views of the deformation field within the impacted specimen. The results show that the strain rate and incident impact energy influence the energy absorption capacities of closed-cell aluminium foams. Furthermore, damage initiation, propagation and cell collapse mechanisms under drop weight impact have been elucidated.

Mar 1, 2017