Search Documents

By M. H. Harris

A solution has been obtained to the problem of calculating flow into a cased and perforated well. Equations describing the idealized system were solved by numerical analysis techniques on a high-speed digital computer. Computer experimentation indicated that the results are within 3 per cent of the exact solution. Computed results are presented as an apparent skin effect, on a series of dimensionless working curves. Productivity ratios can be rapidly calculated from these data for the wide range of wellbore and reservoir properties actually encountered in field practice. Any reasonable vertical unisotropy ratio can be included in the computation. Productivities can be calculated for wells perforated in a regular pattern, a single horizontal plane or a vertical line on one side of the casing. Solutions for asymmetrical perforation patterns can he easily obtained from the working curves. Solutions for flow into sells completed with a horizontal notch are also provided. Results show that productivity can be increased by extending perforation penetration. This is especially true for shallow penetrations. The highest productivity is obtained when perforations are arranged in horizontal planes, as opposed to a vertical line on one side of the casing. Four or five perforations in one plane will approach the maximum productivity. The effect of perforation hole diameter is small, and is rioticeable only in shallow penetrations. INTRODUCTION The perforating method of well completion has been successfully and widely used in most producing areas. In the past, the desired perforation results were achieved by simply shooting numerous large holes in the casing. A perforating scheme for an area, or particular well, was established by evaluating two types of experimental data: the well flow index and the productivity ratio.' 3 The well flow index test is a means of determining the relative flow capacity of perforations in a linear system. This test also gives information on the perforation size, shape and hole damage which can be expected under well-bore conditions. However, relative flow data from this test cannot be accurately tarnsformed into the radial wellbore system. Thus, no true indication of the productive capacity of a perforated well can be obtained from the well flow index test. A well productivity ratio is derived from electrolytic models built to simulate perforated wells. Available productivity ratio data 2,3 are limited in that all important variables are not extensively evaluated. For example, data are limited to well radii of 3 and 6 in., and to maximum perforation penetration of 1 ft. Practically no information is available on the pattern of flow into a perforation. The effect of various perforation patterns on well productivity has not yet been determined and the effect of perforation diameter has not been thoroughly studied. Also, it will be shown that this type of electrolytic model data is probably in error by as much as 10 per cent or more. Modern completion techniques such as limited-entry perforating, single-plane fracturing, steam and hot air injection and chemical consolidation of incompetent formations all rely on injection and/or production from a limited type of completion. These completions may consist of several high-capacity perforations or a horizontal notch which is equivalent to an infinite number of perforations in one plane. Proper design of these new completion techniques requires, in part, accurate estimates of a well's productive capacity. Data on perforated and notched well productivity have been determined in this investigation. Results are presented as a function of the pertinent variables. Equations describing the idealized system were solved by numerical analysis techniques on a high-speed digital computer. DESCRIPTION OF PROBLEM PRACTICAL APPLICATION The computed results can be applied to wells which meet several general specifications. An external drainage radius of the well must be known or assumed, but the well need not be drilled on a regular pattern. The well must be cased and cemented through the entire producing interval. And, the casing must be perforated with one or more horizontal planes of perforations. The perforation pattern itself must conform to three geometrical requirements. 1. The perforations in a plane must divide the plane into equal angular segments (Fig. 1). Four perforations per plane would be 90" apart. 2. Perforations in a plane must be directly above or beneath perforations in adjacent planes. For two shots per plane, perforations would lie in the BB' plane (Fig. 1). 3. Horizontal planes must have equal vertical spacing and be separated from the top and bottom of the formation by one half the spacing interval. Single planes of perforations should be in the middle of the formation. This is shown in Fig. 2 where h is the formation thickness in a single plane conlpletion or the spacnig interval in a multiple plane completion. The spacing interval at the top and bottom of the formation may vary somewhat without causing an appreciable error in the productivity calculation if the formation is reasonably thick and there are many horizontal planes of perforations. A special provision has been made to calculate the productivity ratios of wells with uneven spacing intervals, or for the case where a single plane of perfora-

Jan 1, 1967

By W. J. Kuit

"Complex facilities which provide for the collection, management and treatment of effluents emanating from the Sullivan mine and concentrator tailings were made operational in October 1979. Key features of the system are the use of upgraded tailings ponds for the storage of up to 800 million litres of metals-contaminated effluents, a treatment plant employing lime in a high-density sludge process and a sludge-impoundment facility designed for maximum long-term environmental safety. The completed works are capable of satisfying a difficult range of operating requirements imposed by highly variable weather conditions, drainage flows and soluble metals loadings. Final capital expenditures for the project approached $10 million and annual operating costs are about $0.8 million.This paper discusses the Kimberley effluents treatment project and the major considerations in its development. The treatment process, major plant equipment and initial operating experience are also described.IntroductionCominco Ltd. has worked the Sullivan orebody at Kimberley, B.C. since 1909 and has operated a concentrator some 5 km distant from the mine since 1923. Over the last 70 years, in excess of 120million tonnes of ore have been mined, and production continues at an average rate of 6,500 tonnes per day. It is a well-known fact that the contribution of this operation to Canada's mining industry and, in particular, Cominco's development has been significant. However, this success has not been without some undesirable side effects.Unfortunately, the Sullivan is one of only a few major Western Canadian orebodies which may be classed as ""acidic"" in nature. That is, the primary economic minerals, galena and marrnatite, are enclosed in a siliceous host rock with abundant pyrrhotite, but with little or no accompanying alkaline gangue minerals such as calcite and dolomite. The unavoidable consequence of mining such an ore is that contact with air and water generates an acid mine drainage containing various soluble metals orginally present as minerals.This problem also arises in the concentrator's tailings ponds, which, in the case of the Sullivan, are two separate impoundments of different materials. The 1,100 tonnesl day of ""iron"" tailings are primarily pyrrhotite which is surplus to the requirements of a separate operation that produces sulphuric acid as an intermediate to phosphate fertilizers. Inert gangue minerals with only a minor sulphide content are the main constituents of the 1,200 tonnes/ day of siliceous tailings. Corresponding to the relative proportion of sulphides in the solids, the decant from the iron tailings is substantially more contaminated than that from the siliceous pond."

Jan 1, 1980

By M. Javier

In business mining, dilution is the result of the operating parameters that occur too often and cause serious consequences to mine performance, questioning TO WHOM BENEFITS DILUTION. Mining persists in changing perception of real meaning of dilution. The lack of interrelation between mineral processes and nature compromises the understanding of dilution; this absence of interrelation occurs due to the misinterpretation of nature, otherwise, Geomimic could be helpful to filling the gap of misinformation. NATURE provides LIMITED metals in low content deposits; it is a challenge to obtain them. Nature never considers dilution. Furthermore, though dilution is a human concept, dilution is accepted and promoted. Reality of dilution is in its errors accumulation that translates into technology level or status applied in nature. It is doubtful that dilution can continue surviving if it is ?meaningless?. It will discourse: Is dilution illegal? If the change occurs in the prediction of mining will prevail a different destiny, it is important to touch the cores of the business; otherwise, it would represent repetition of the same ?negative? effects, as usual. Mining defines many losses during the disturbance of nature, from NPV elaboration to the metal recovery to commerce, demanding BETTER DESIGN. This paper introduces and applies MANAGEMENT BY LOSS, as first steps, to limit risks and uncertainties in mining. As result, the management of dilution will be obtainable under mining practices which promotes its character of SUSTAINABILITY.

Feb 23, 2014

By Alexander May

In its role of providing technology to promote the efficient use of minerals and mineral process waste, the U.S. Bureau of Mines has conducted research at: its Tuscaloosa Research Center to identify and develop high volume uses for phosphogypsum. Mixtures containing a maximum of 50 percent phosphogypsum, 6 to 10 percent lime, and the remainder fly ash had compressive strengths as high as 4,800 psi. The effects of the mounts of phosphogypsum, lime, and fly ash were investigated. Also, the effects of fly ash to lime ratios were studied.

Jan 1, 1983

By James F. Devine

The radial, vertical, and transverse components of particle velocity were recorded by Bureau of Mines investigators along gage arrays extending in one or two directions for 145 to 3,170 feet at five quarries. Of the 39 quarry blasts, 12 were instantaneous blasts, 5 were of the one hole per delay type, using millisecond delayed caps, and 22 were multiple hole per delay type employing millisecond delay detonating fuse connectors. Charge weight per hole ranged from 8 to 1,500 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 25 to 4,620 pounds.

Jan 1, 1966

By Sung-Joo Lee, Gi-Chon Han, Nam-Il Um, Hee-Chan Cho

"In Korea, almost all of bottom ash produced by coal power plants is disposed of in ash ponds. Ash storage areas comprise more than 80% of most coal power plant sites. This disposal method is causing environmental problems and a managerial burden for plant operators. In this study, investigations to develop a beneficiation process for separating coal pond ash into various products were undertaken. To improve efficiency of the separation, coal ash was separated by sizes and each size fraction was subject to various beneficiation processes. The separation process used were flotation (-200 mesh size), hindered settling (16x200) and tabling (16x200 and 8x16 mesh). The results showed that various marketable products, such as lightweight aggregate, sand, high-carbon fuel, could be recovered from coal pond ash using simple physical separation techniques.IntroductionDue to the increased use of coals every year, about fifty million ton of coals were used in 2007 alone. As a result, about 6 million tons of coal ash were generated. In Korea, the coal bottom ash is classified as a general industrial waste and is usually disposed of in ash ponds. The costs for this disposal method continue to increase due to rising costs of site management and development and more strict environmental regulation. Therefore, utilities are constantly looking for ways to increase utilization of coal ash. In this study, various beneficiation processes were evaluated to examine the possibility of separating coal pond ash into various products which can be used as aggregates and high-carbon fuel."

Jan 1, 2008

From 2009 to 2012, Aker Wirth, in cooperation with the BGR (German Federal Institute for Geosciences and Natural Resources), developed a concept for the deep sea mining of manganese nodules, which it also examined by means of a profitability analysis. The study was undertaken for the German Federal Ministry of Economics and Technology. The increasing scarcity of resources, coupled with the continuous rise in resource prices, drive the search for new raw material deposits. As a result, the deep sea is coming increasingly under the spotlight. At depths of more than 1,000 m (3,280 ft), large deposits of ores and precious and high-tech metals, such as manganese, cobalt, nickel, copper and gold, along with rare earths (which are important for the high-tech industry), can be found. The extreme deep sea conditions ? enormous water pressure, ice-cold temperatures and complete darkness ? present huge financial and technical challenges to the mining industry when extracting these materials. Aker Wirth has recognized the potential of this important future market early on and advances the development of relevant products.

Jan 1, 2013

By P Bonniwell

As a part of the Newcrest, Telfer Expansion Project, a consortium of Australian, Canadian and South African Mining Contractors in joint venture have been contracted to develop the hoisting shaft. The parties namely; Byrnecut Mining Pty Ltd, Murray and Roberts RUC and Thyssen Mining Construction of Canada Ltd have combined their individual expertise to excavate the shaft. There is a particular emphasis on the use of proven shaft sinking techniques from North America and in particular integrating electric hydraulic drilling equipment and personnel from the Canadian Mining industry. The Telfer hoist shaft when completed will have a finished diameter of 7.1 metres and extend to a depth of 1170 metres below the collar. The shaft will be fully concrete lined and will later be equipped for hoisting ore from the Telfer deeps at a rate of five million tonnes per annum. The shaft when completed will be the largest shaft ever completed in Australia on a volumetric basis. This paper will examine the technical aspects of the shaft sink, as well as exploring the integration of personnel and equipment from the frozen prairies of Saskatchewan, Canada into an operation in the Great Sandy Desert of Western Australia. What are the spin-off benefits for the development of other shafts within Australia?

Jan 1, 2005

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic location or seam characteristics modem raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality and these objectives may be sought by commencing the preparation of coal underground at the "working face." Underground preparation involves choosing those portions of the bed which can be cleaned to satisfy predetermined market requirements involving (1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1) seam under development, (2) mining equipment available and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another the (1) petrography of the coal in the bed does not re- main uniform, (2) character of roof and floor are subject to change and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content and petrography are of considerable interest and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal. The prospecting and evaluation of any area containing one or more salable coal beds by means of channel samples taken from outcrop openings and/or from diamond-drill cores can yield valuable data on coal characteristics. By correlating the data developed from distinct petrographic sections of channel and/or drill core samples, the quality of the bed according to stratification will be evident. There are few coal beds that do not show wide variations of such characteristics as ash and sulfur

Jan 1, 1968

By E. Haug, Quamrul Ahsan, R. Norcross

Cyanide leaching is the most common process employed in the majority of the gold extraction plants. These gold extraction plants naturally generate tailings and/or effluents that contain highly toxic cyanides, In geographic locations with excess precipitation and therefore net positive water balance, a portion of these tailings must be discharged. Before these highly toxic cyanide-containing effluents can be discharged to the waterways, cyanide and any other toxic substance must be destroyed. Geographic locations with high evaporation and low precipitation, as in the western USA, result in net negative water balance and therefore these plants can operate with a zero discharge option. However, with the current stringent environ­mental regulations and concerns for bird and wildlife mortality, even these operations may be required to partially treat their tailings to preclude potential harm to wildlife. Furthermore, heap leach opera­tions are now generally required to detoxify the heaps before abandonment. It is, there­fore, apparent that all gold extraction plants may be required to install some form of effluent treatment in order to achieve the above objectives,.

Jan 1, 1990

By Ravindra M. Nadkarni, Milton E. Wadsworth

The kinetics of cetnentation of copper with iron were observed to follow first-order kinetics and increase with speed of agitation to a limiting value. Maximum rates agree closely with theoretical values based upon a model of aqueous solution diffusion through a litniting boundary film. Back reaction kinetics are shown both theoretically and experimentally to be independent of ferrous iron concentration in solution. The inlportance of attnospheres of air, oxygen, nitrogen, and hydrogen was studied and the results have been correlated with several impovtant oxidation processes involving metallic iron and copper. The kinetics of the reaction of ferric ion with metallic iron were found to be slow in the absence of metallic copper and essentially proportional to the surface area of metallic copper present in the system. THE precipitation of copper on iron is classic as an example of a relatively ancient art applied successfully for centuries with little fundamental understanding of the important parameters involved. There is some indication that the process has been a commercial means to produce copper since the sixteenth century.' The amount of fundamental work on the cementation of copper with iron is not great. Wartman and Roberson2 carried out a series of detailed copper cementation experiments using natural and synthetic mine water. The following were presented as the three principal reactions: Reaction [I] is the desired cementation reaction and accordingly 0.88 lb of iron would produce 1 lb of copper. In actual practice iron consumption would more normally fall in the range of 1.5 to 2.5 lb per lb of copper. Wartman and Roberson attributed the excess consumption of iron to Reactions [2] and [3]. They found that Reactions [I] and [2] proceeded at approximately the same velocity while Reaction [3] was much slower and would be diminished by controlling the contact time. It was also pointed out that increased agitation is beneficial in removing hydrogen bubbles and barren layers of solution at the iron surface as well as removing contaminants resulting from the hydrolysis of iron. Episkoposyan3 and Episkoposyan and Kakovskii4 studied copper and silver cementation on rotating iron disks in chloride solutions. The kinetics based upon a diffusion model were first order and varied linearly with surface area and with angular velocity raised to the one-half power according to the Levich equation. The experimental activation energy for both copper and silver was approximately 3 kcal per per mole. Excess iron consumption was found to increase with temperature. The rate of cementation first increased with increasing acidity and then diminished at high acid concentrations. sutolov5 has presented an excellent review of the Leach-Precipitation-Flotation (LPF) process including a discussion of copper cementation from an electrochemical point of view although few experimental results were presented. From voltage considerations he predicted that cementation should not be influenced by the concentration of ferrous iron in solution. He considered several secondary reactions including Reactions [2] and [3] and pointed out the importance of oxidation of ferrous iron to ferric with oxygen. In addition it was suggested that Reaction [2] was enhanced by the dissolution of metallic copper by ferric iron which in turn consumed excess iron by the cementation reaction, Eq.[1]. Cementation of copper on metals other than iron has been studied by several investigators but, as in the case of iron, the amount of fundamental work is not extensive. Bashkova and kovalenko6 and Bashkova7 studied the cementation of copper on indium from copper and indium sulfate solutions. The rate was found to be first order and to increase with acidity. This was associated with a decrease in potential (EIn — ECu) and the simultaneous reduction of hydrogen ions at low pH. The rate of cementation also decreased with increasing indium concentrations which was postulated to be due to the decrease in the rate of diffusion of the ions in solution. Below 97°C the experimental activation energy was found to have the unusually low value of 2 kcal per mole and was attributed to diffusional control. Above 97°C the rate increased suddenly and was explained as a change in the rate-controlling step to a chemical reaction. In Part I of this study Nadkarni et a1 .1 have reported on preliminary results obtained in a laboratory study of the kinetics of the cementation process. The rate was found to be first order, proportional to the surface area of the iron, and to increase with speed of stirring until a maximum rate was observed. At low stirring speeds the deposit was spongy and adherent. At medium speeds the copper peeled off in bright strips and at high speeds finely divided copper was produced and continually removed from the surface. The amount of excess iron consumed increased with speed of stirring and with temperature. The average experimental activation energy combining results from several types of iron was 5.8 + 1.6 kcal per mole suggesting diffusional control through a limiting boundary film. Traditionally copper cementation has been carried out over the centuries in gravity-fed launders of various design containing scrap iron. More recently rotating drum precipitators and activated launders8'10 have been used. In the latter, copper-bearing solutions are

Jan 1, 1968

By A. U. Seybol

Eight binary iron alloys were examined after ion nitriding experiments to determine the behavior of the following elements: Al, Mo, Mn, Si, Ti, V,Cr, and C. Only Al, Cr, Ti, and V additions caused hardening in binary iron alloys. A few steels were examined to see the effect of Cr, Cr + Al, Cr + Ti, and Cr + V. It is suggested that a useful new class of ni-triding grade steels might be those containing about I pct V. The nitriding of steel, first described by Fry1 about 45 years ago, rapidly attained commercial application with very little knowledge of the fundamentals involved. While Fry,' in describing the status of nitriding in 1932, apparently correctly postulated hardening by precipitated nitrides, the details of the nitriding process were not understood, nor has the situation changed much since that time. It is also interesting to note that the compositions of some typical nitriding steels given by Fry at that time have changed little in the intervening years. Currently used nitriding steels owe their surface hardening to either chromium (as in 4340 steel) or aluminum plus chromium as in the Nitralloy grades, where both CrN and AlN appear to contribute to harden ing. Titanium additions have been studied experimentally, but thus far titanium steels have not won wide commercial acceptance. This subject will be expanded later. The orthodox ammonia nitriding process has been reviewed very adequately many times as in Jenkins3 and Case and VanHorn,4 and their is no need to outline the process here. Ion nitriding is not as well-known, although there have been several descriptions5-9 of the process given, sometimes with comparisons with the ammonia process. Most of these papers are primarily concerned with a description of the equipment, or of the physics or electrical engineering aspects of ion nitriding, but Noren and Kindbom9 gave the results of a metallurgical investigation using both processes. In brief, ion nitriding is carried out in a vacuum chamber from which the air is exhausted and replaced by a N2-H2 mixture, typically containing 10 to 20 pct N2, at about 5 to 10 torr pressure. While ammonia gas has also been used in ion nitriding, there is no evidence that ammonia makes any improvement in the ion nitriding process. A few hundred volts dc is applied between the grounded container wall (positive) and an insulated center post supporting the work (negative) to be nitrided. A glow discharge is created in the ionized gas, accelerating positive nitrogen ions to the work. These ions contain enough energy to form the normally unstable Fe4N "white layer", thus establish- ing surface nitrogen solubility characteristic of the a Fe/Fe4N equilibrium. This creates a substantial concentration gradient, driving dissolved nitrogen into the steel. The temperature employed is in the same range (around 500" to 550°C) as in ammonia nitriding, but because of factors which are not understood at present the nitriding time is ordinarily considerably reduced in ion nitriding. Other advantages have been cited,9 but it is not the purpose of the present work to contrast the two processes. The present objective was to examine the behavior of binary iron alloys during ion nitriding with respect to the microstructure, hardness level, and depth, and to examine some of these factors in steels as well. In this way it was hoped to be able to find out something about the individual role of these elements in steels. While all the work was done by ion nitriding, there seems to be no reason why any conclusions reached would not equally apply to ammonia nitriding, excepting only the kinetic aspects of the process. Another objective was an exploration of the critical-ity of the ion nitriding variables: gas composition, pressure, temperature, and time. EQUIPMENT AND MATERIALS The equipment used was substantially as described by Jones and Martin.8 The vacuum tank was about 12 in. in diam by about 18 in. high, and consisted of water-cooled stainless steel, with a single small window at the top for viewing inside. This sat on a heavy mild steel base equipped with the main pumping port, pressure control port, and vacuum gaging. A series of variable resistances was interposed between the glow discharge and a large-capacity -40 amp variable primary transformer feeding a 1000-v transformer, but 600 v were about the maximum ordinarily used. With the small l-in.-round, 4-in.-thick discs used for nitriding, the electrical load was usually about 500 v at 0.8 amp. The specimen temperature was controlled by a stainless-steel sheathed chromel-alumel couple, whose junction was in the steel stool upon which the flat discs were placed. These were ground through 400 Sic paper. Cycling of the temperature controller caused -0.2 amp variation in ion current, providing an ample control band. The binary iron alloys were made from vacuum-melted hydrogen-deoxidized electrolytic iron and alloys of 99.9 pct purity. Cast ll-lb-square tapered ingots were forged and hot-rolled to about 11/4-in.-diam rounds. Discs of 1/4 in. thickness by about 1 in. diam were machined from the rods for nitriding specimens. The following alloys were prepared: 1 pct each of Mn, Mo, Cr, Ti, Al, V, Si, and an Fe-0.8 pct C alloy. EXPERIMENTAL VARIABLES Of the variables total gas pressure, nitrogen partial pressure, temperature, and time, only nitrogen partial pressure was found to be critical to the operation. A critical nitrogen partial pressure was found corre-

Jan 1, 1970

By J. Herbst, C. C. Harris, G. Poling

The modern flotation machine is the result of decades of adaptation to a changing environment. In response to falling ore grades, and rising demands, tonnages, and costs, attempts are now underway to expand machine capacity by about an order of magnitude, while at the same time maintaining metallurgical performance and if possible reducing power requirements per unit throughput. Empiricism and rule-of-thumb have guided flotation machine design and scale-up, and a current need is for the development of a fundamental understanding of the subject. Design features of current and some obsolete machines are discussed in an attempt to outline those principles of flotation machine design which are known, and to delineate topics needing investigation. Attempts are made to distinguish between essential machine features required by the physics of the process, those features resulting from speculative theories on the flotation mechanisms, and features which are essentially styling variations. Topics discussed include: flotation mechanisms; tank and impeller/ stator design and dimensions; impeller speed; aeration; power consumption; particle suspension and dispersion; capacity; correlation of design parameters and operating variables; scale-up and scale- down; materials flow; problems in machine design. Design details and operating data for several current machine families are provided in Appendices.

Jan 1, 1976

By G. R. Chaudhury

Many base metals, such as copper, lead and zinc, are commercially extracted by thermal processing of sulphide concentrates. However, owing to the depletion of high grade sulphide ore reserves and to environmental legislation, efforts have been in progress for some years to develop methods for the extraction of metals from lower-grade oxide ores and secondary resources, and there are now examples of commercial-scale operations.

Dec 1, 1995

By Craig R. Barrett, Jack L. Lytton, Oleg D. Sherby

The types of substructures developed during high-temperature creep of (110)[001]-oriented polycrys-talline Fe-3.1 pct Si were examined by electroetching of dislocation sites. Edge dislocations were observed to accumulate adjacent to grain boundaries and poly-gonize perpendicular to their glide planes to form a "Pile-up" of nearly parallel tilt boundaries. The dislocation density developed within the grains during steady-state creep was found to increase with increasing stress. The formation of periodically spaced groups of edge dislocations along grain boundaries was observed, and it was proposed that these formed to relive bending stresses at grain boundary shear .faults. Grain boundary serrations developed at these faults, and it was suggested that this was a result of localized grain boundary migration at the polygonized groups. THE authors have conducted a series of high-temperature creep tests on (110)[001]-oriented poly-crystalline Fe-3.1 pct Si sheet. The creep specimens were examined at various stages of creep by means of electrolytic etching of dislocation sites using the chrome-acetic acid solution developed by Morris.' Hibbard and Dunn2 have demonstrated that the etch pits produced with this technique correspond to single dislocations. It is the purpose of this paper to present and discuss the dislocation substructures which were formed during high-temperature creep at constant stress. EXPERIMENTAL PROCEDURES The polycrystalline Fe-3.1 pct Si sheet employed in this study contained a (110)[001] texture. This texture was quite strong, and the elastic properties of the sheet closely approached those of a single crystal of iron.3,4 A typical analysis in weight percent for this material is 3.1 Si, 0.1 Mn, 0.003 C,

Jan 1, 1965

By P. A. Beck, Hsun Hu

It has been known for many years that in cold drawn polycrystalline aluminum the recrystallization texture is practically identical with the deformation texture.l,2,3 V. Goeler and Sachs4 stated that in cold rolled polycrystalline aluminum, too, the deformation texture is retained upon recrystallization. This behavior was interpreted by Dehlinger9 as an indication that each recrystallized grain inherits the orientation of the matrix in which it grew. However, Burgers and Basart showed6 that in deformed aluminum single crystals the orientation of the recrystallized grains strongly deviates from that of the matrix. Barrett demonstrated8 that even in deformed polycrystalline aggregates the local orientation within each deformed grain changes on recrystallization. No explanation has as yet been offered of how the aggregate texture can be retained, while the local texture is everywhere changing. According to Burgers and Louwerse6 the orientation change on recrystallization in compressed and rolled aluminum single crystals corresponds to a rotation around [112] axes lying in the active slip planes and perpendicular to active slip directions. This orientation change was rationalized by them on the assumption that the orientation of the recrystallized grains is determined by the orientation of the available nuclei, and that these nuclei are small fragments of the deformed crystal, rotated in the deformation process. Barrett pointed out,? however, that these assumptions were by no means proven, and that the total volume of material necessary for the nuclei is so small, that it must be available in any orien- tation whatever. It is, therefore, unlikely that an "oriented nucleation" theory could satisfactorily explain the orientation changes in recrystallization of a deformed crystal. Furthermore, in contradiction to Burgers and LOU-werse's conclusions, Barrett's results for the orientation change could be best expressed in terms of rotations around. [Ill] axes. Thus agreement is lacking not only in the interpretations but apparently even in the experimental results contributed by the various investigators. The orientation relationships on coarsening* in a highly oriented polycrystalline matrix were first investigated by Burgers and Basart.5 They produced a fine grained highly oriented matrix by the recrystallization of a compressed or rolled single crystal of aluminum, and studied the orientation relationships in three successive generations of crystals: the "deformation texture" in the single crystal, the recrystallization texture, and the coarsening texture. Burgers24 showed that the preferred orientation of each successive generation was almost always widely different from that of the preceding one, but that the coarse grains often approximately reverted to the orientation of their grandparent, the deformed single crystal. This observation, and the idea that the orientation of the coarse grains is determined by that of the available "nuclei," led to the concept that the coarse grains are nucleated by the remnants of the deformation texture.12,15 On the other hand, Bowles and Boas16 found, in a carefully conducted experiment, that in recrystallized fine grained copper of cube texture coarse grains grow in orientations which can be derived from the orientation of the recrystallized matrix by rotation around a [lll].] direction: the coarsening texture here does not appear to be related in any simple manner to the original rolling texture from which the cube texture had been obtained by recrystallization. It may be assumed that in a recrystallized material, even with a strong texture, there always are present some grains of practically any orientation. These may serve as "nuclei" for the coarse grains, provided that the conditions are favorable for their growth. The existence of a coarsening texture may be considered as an indication that grains with certain relative orientations with respect to the preferred orientation of their neighbors can grow much faster than others. This "oriented growth" theory was briefly suggested by van Arkel, as early as 1936,13 and it was mentioned by Burgers." Recently, C. G. Dunn produced direct

Jan 1, 1950

By R. Paul De Bruyn

A. Crane Check List -- Make -- Model -- Year of Manufacture -- Where is load chart? Is it for this crane? -- Boom style and length -- Boom tip drawing (sketch) for fixed lead connection. Has the crane manufacturer been consulted on the point of attachment? -- How many drums; diameter and length of wire rope. -- Is the single part line pull enough to lift pile or hammer on single part line? -- What is the effective weight of the whole driving system - leads, pile, hammer, etc? -- Are there any auxilliary hydraulic systems? Are the line pulls on these adequate to lift the pile or hammer? -- What is the anticipated working radius? Will the spotter collapse to that length? -- Nature of foundation under crane - barge, marsh, unstable sand, etc. -- Does the crane meet OSAH and state regulations -current certification. Note - the operator is responsible for compliance with regulations. -- Is there any extra weight added to counterweight by compressors or hydraulic systems? What does crane manufacturer say? Consult factory before adding.

Jan 1, 1990

By Hare S. M, Lumsdaine I, O&apos

Converter slag assaying 3.7 per cent Cu is produced by Mount Isa copper smelter at a rate of up to 180 000 tonnes per annum.Priority is given to the processing of ore, however concentrator capacity periodically exceeds that of the mine and the opportunity is taken to treat converter slag. It is processed in batch campaigns, typically through the Copper Concentrator, but the Hilton Concentrator has also been used. Slag and ore are kept as separate as possible, since each has an adverse effect on the flotation performance of the other.

Jan 1, 1993

By L. C. IlsLey

A preliminary investigation has recently been made by the U. S. Bureau of Mines to determine whether or not the ordinary mine- type telephone is entirely safe in gaseous atmospheres . Two well known makes of mine- type phones were purchased for this investigation . It is not conceivable that the current necessary for talking over telephones could ignite gas . However , such phones are provided with efficient magnetos , and it was believed that danger might result from the ringing of the magneto . Again , while this type of phone has been designed to have a certain measure of dust and moisture tightness , evidently it has not been designed as an explosion- proof device . either with regard to cover joints and fastenings or strength of castings . Therefore , the problem was simplified . First it was assumed that owing to the construction of the telephones the gas would penetrate into their interior , and the question was to ascertain whether or not the gas would be ignited from the operation of the magneto .

Jan 1, 1922

By T. M. Broderick

InveStIgations into the possibilities of economically mining and concentrating low-grade iron ores of the Lake Superior region are attracting increasing attention. Among the organizations that are carrying on the work are the United States Bureau of Mines, the State of Minnesota (which spends about $80,000 annually on problems of the iron and ferroalloy ores of Minnesota), and the State of Michigan (which spends about $10,000 annually of its iron-ore research). Several of the mining companies are also financing research. Of the states in the Lake Superior district, Minnesota has done most in iron-ore concentration. In 1930, thirty-seven concentrating plants were in operation on the Mesabi Range, beneficiating about one-third of the total ore shipped. About one-half of these plants reduced silica; the others reduced moisture or improved the structure of the ore.' Research into the possibilities of magnetic concentration of the Eastern Mesabi magnetite ores indicates that vast tonnages of that ore may be utilized at a profit in the not distant future. Magnetic concentration has also been tried at Sellwood, Ontario, on the Moose Mountain deposit, and at the Berkshire mine in Wisconsin on the magnetic ores of the Western Gogebic Range. There have been few attempts to concentrate Michigan iron ores. In order to determine the possibilities of such concentration, iron-ore research has been carried on at the Michigan College of Mining and Technology for the past few years. After a general survey of the iron ores of the state, a program of more detailed experimentation was outlined, starting with work on the Ironwood formation of the Gogebic Range. The results of this research led to the belief that gravity methods will produce fairly satisfactory concentrates from the parts of the iron formation that are made up of comparatively thick alternating beds of rather high-grade ore and lean chert. About 85 per cent of the iron and steel produced in the United States comes from ores of the Lake Superior district. The reserves of direct

Jan 1, 1935