Search Documents

The Mineral Resources Act 1989 was assented to on 25th October, 1989 after more than two years of consultation and negotiation between Government, the mining industry and other affected parties particularly the major rural organisations.The legislation proposes major conceptual changes in a number of areas and adopts a totally new approach to the definition of land and the mechanisms available to the mining industry for accessing such land.Unfortunately the passage of the legislation through Parliament coincided with the lead-up to the State election. Ultimately it became an election issue generating much adverse comment in the media particularly from rural and landholder groups. It was obvious that much of this anti-mining propaganda resulted from a lack of understanding of the legislation and the benefits that flow to the majority of landholders as well as the mining industry.It is essential that the contents of the Mineral Resources Act be thoroughly understood by all parties. Only then will all the State's resources be able to be developed in a multiple land use environment.This paper outlines the philosophy behind the new Act and the more important provisions contained therein.

Jan 1, 1990

By Robert Bakish

VARIOUS aspects of structure-sensitive corrosion of single crystals and polycrystalline aggregates of Cu,Au have been presented in papers by the author, in association with W. D. Robertson. Prompted by some observations in the course of these studies, a new approach to the problem was undertaken. Results of these new experiments are reported here. Thin slices, less than 2 mm thick, were prepared from single crystals 3.5 mm in diam grown by the Bridgman technique. The crystals were homogen- ized for 300 hr at 850°C. Crystals with no deformation, crystals deformed in tension to the yield point, and crystals deformed 20 pct in excess of the yield point were used. Crystals of several different orientations were studied. Slices were immersed for one month in 2 pct aqueous solution of FeCl3 and, subsequent to this immersion, were subjected to bending. Immersion and bending were carried out at room temperature. The size and geometry of the crystals did not permit accurate data on the loads involved. A most unexpected result was obtained in the process of bending these slices of Cu3Au crystals normal to the (110) plane. Completely brittle be-

Jan 1, 1958

By Malcolm Scoble

School Values ?? Each other; ?? Students, & helping them develop intellectually, personally & professionally; ?? Freedom to pursue educational & research opportunities; ?? Home-work-life balance; ?? The geographic-business community in which we operate ; ?? The pursuit of excellence; ?? Our contribution to society; ?? Creativity & innovation; ?? Teamwork & collaboration; ?? Career development, achievement & reward.

May 1, 2008

By Erie F. Wolstenholme

The purpose of this paper is to describe work undertaken, within the System Dynamics Research Group at Bradford Management Centre, into the development and application of a System Dynamics model of an international mineral industry; aimed at providing a basis for analysis of the interrelationship of supply, consumption and price over time, under different production and stocking policies. A review is presented of some of the major characteristics and problems associated with such industries. This is followed by an outline description of the model and the way it has been applied to examine various supply responses, in the light of changing consumption patterns. Demonstration results deal with model validation and with analysis of international buffer stocks and conflicting supply policies on the historic situation in the copper industry.

Jan 1, 1979

By David H. Y. Tang, Syd S. Peng

In general, the strata sequence of the immediate roof in the under- ground coal mine openings can be divided into three types. They are: (A) each stratum deflects independently, (B) some stratum (or strata) loads on the underlying stratum, and (C) each stratum loads on its underlying stratum. The flexural behavior of the immediate roof which is made up of multiple strata not only depends on the material property, geometry, and external loading of rock strata, but also on the strata sequence. A computer program based on the beam-column theory is written for determining the bending stress and deflection for the generalized immediate roof. The flexural behavior of the immediate roof in various strata sequences are investigated for the following effects: roof span, horizontal stress, thickness and Young's modulus of the lowest stratum. In addition, some of the results are compared with the results of the finite element method.

Jan 1, 1983

By Mallett C

Coal mines are dynamic systems that change continually in size, shape, and condition. Large quantities of data about production, coal quality, ground stability, ventilation monitoring, equipment performance and location, vehicle and personnel movements and geology, are generated from all parts of the mine.Internet technology and virtual reality technology are now being combined to provide an intuitive, multi-dimensional information system which can simultaneously display any information that can be collected and stored by a computer. Physical information is directly displayed as 3-dimensional objects in the mine model. Numerical and text information is dynamically linked to these objects and accessed by "clicking" on them.

Jan 1, 1998

By Donald W. Gentry

Many firms in the minerals industry are facing enormous capital-equipment requirements for existing operations, planned expansion programs, pollution control systems, etc. Yet, because of existing economic conditions, mining companies find it increasingly difficult to obtain reasonable financing for the acquisition of large, high-cost capital equipment. One way of obtaining the use of mining and other major pieces of high-cost capital equipment is through leasing. The popularity of this approach is evidenced by the growing number of leasing companies, equipment manufacturers, and financial institutions now offering this service to their customers. Indeed, leasing has become a billion-dollar industry, and many commercial banks have developed sizeable portfolios in this area. "Should we buy or lease?" This question eventually comes up whenever a mining company needs additional major capital assets. Unfortunately, many buy-or-lease decisions are made on an emotional basis-rather than on a proper financial evaluation that would yield the…

Jan 9, 1975

By Gianfranco Ferrara, Carlos A. Guimaraes, M. C. Williams, T. P. Meloy

Presented is a method of continuously producing very narrowly sized particle streams. Currently Sieve Cascadography is a batch method of analyzing particle shape - a form of particle chromatography. This paper introduces and analyzes the continuous Sieve Cascadograph, a device that enables a series of narrowly sized particle fractions to be produced continuously. Properly designed, the continuous Sieve Cascadograph will produce many product streams of particles with as little as one percent difference in particle size within a given size fraction - an order of magnitude better than existing technology permits. By varying operating conditions, the size of the output fractions may be varied.

Jan 1, 1992

By H. Sis, S. Chander

The pressure filtration behaviors of dispersed and flocculated alumnae slurries at high percent solids were investigated with the objective of determining the effect of surfactant type and concentration on slurry properties. A high-purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by pH and by surfactants that are known to act as electric and steric stabilizers. The effects of both ionic and nonionic sutfactants were investigated. Surface charge measurements of the slurries were carried out by an electrokinetic sonic amplitude (ESA) method to better understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and cake properties are discussed.

Jan 1, 2000

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationships in fact discernable.

Jan 1, 2011

By R. Haynes

ON the basis of compositional changes of a phase observed in a eutectoid Cu-Al alloy1 it has been suggested that mechanisms for the decomposition of the ß phase proposed by earlier workers2-5 were incorrect. These data are reinterpreted in conjunction with lattice parameter data obtained on an alloy containing 12.2 pet Al, whose isothermal transformations have been reported elsewhere.5 The a Lattice Parameters of a 12.2 Pet A1-Cu Alloy—~iffraction patterns of completely transformed specimens were obtained in a back reflection camera using copper Ka radiation. Lattice parameters of

Jan 1, 1959

By Angel Benjamín

En Minera Coimolache se generan 720 m3 anuales de residuos semisólidos (grasas) en las trampas posteriores al alcantarillado de los comedores, los cuales al carecer de tratamientos de depuración estos eran trasladados por una empresa prestadora de servicios de residuos. Por el contrario en la actualidad se viene utilizando la microbiología enzimática y micronutrientes naturales que alimentan, fortalecen y potencian las bacterias que existen y crecen en la grasa acelerando el proceso de biodegradación como primera fase para reducir la grasa en un 70%.

Sep 1, 2017

By Stuart M. Jones

This paper describes the state of the art of grinding in the Copper Industry today including descriptions of the largest equipment and design features which allow processing of as much as 100,000 mtpd in a single mill line. We include a typical flowsheet, control philosophies, and maintenance techniques which result in low cost production which is essential in today's market.

Jan 1, 1999

By Berthold Pilz

The importance of a power economy that is efficient both in technological and economic terms has been clearly recognized in recent years. In 1977 the German Federal Government therefore introduced its Energy Research and Energy Technologies Program 1977-1980, which consolidates the government activities in the field of nuclear and non-nuclear energy research. The priority objectives of this program can be summarized as follows: safeguarding the medium- to long-term energy supply in the Federal Republic of Germany at reasonable overall macroeconomic cost, taking into account the requirements of environmental protection and the safety of the population. In the field of coal mining technologies, about 200 research projects are currently under way. A total of DM 1.7 billion is earmarked for research to be conducted in this area between 1977 and 1980.

Jan 1, 1979

By J. F. Able, F. Djahanguiri

The US Bureau of Mines conducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1998

"Minerals in Transition" is the timely theme of this year's SME-AIME Fall Meeting and Exhibit, to be held September 10-12 at the Salt Palace, Salt Lake City, Utah. Approximately 2000 members and guests are expected to attend the meeting, which will include 117 technical papers, presented during 27 sessions. To complement the technical program, a record number of mining manufacturers and suppliers will be on hand to exhibit the latest in equipment innovation and professional services.

Jan 8, 1975

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTLATION NETWORK ANALYSIS

Jan 1, 1977

By Sadough vanini Ali

The silicon anisotropic wet chemical etching technique is widely employed for fabricating various microelectromechanical system (MEMS) structures for advantages such as simple etching equipment and its capability to fabricate special microstructures. In this paper, we consider a complete theoretical derivation of the analytical solution based on geometrical and kinetic aspects of step flow on any surface and with a mathematical method we derive new equation for calculating the microscopic etch rates of surface atoms for a new range of concentrations and temperatures. Furthermore, a novel equation is presented for the calculation of the microscopic activation energies for some typical surface atoms and a new comparison of activation energies between some atoms is made that divides atoms into three categories. The results demonstrate agreement with the experimental results.

Oct 1, 2011

By S. H. Castro

In 1997 Chile was the world's largest copper mine producer with around 3.4 million metric tomes of copper. Conventional technology (conminution-flotation- smelting-converting-electrorefining) for copper sulfide ores was used. For copper oxidized ores hydrometallurgical processes (heap leaching-solvent extraction- electrowinning) were employed. Consequently, the most important waste effluents include flotation tailings, gaseous emissions, smelter slags, acidic and alkaline wastewater, electrolytic sludges, solid residues from leaching, etc. The introduction of stricter environmental regulations are forcing the Chilean industry to minimise the generation of waste and promote cleaner production. Gas emissions such as SO2 and arsenic from smelters and process wastewater are the major problems at this stage. The environmental impact assessment of gas emissions in all six largest smelters namely Chuquicamata, Caletones, Potrenllos, Ventanas, Paipote and Chagres led to design a "decontamination plan." The implementation of this plan resulted in (i) the installation of sulfuric acid plants for SO2 abatement and (ii) the installation of electrostatic precipitators to remove arsenic oxides condensed from cooling gases. The aim of this paper is (i) to describe the type of waste associated to the various stages of the metallurgical processes and (ii) review the main abatement technologies used in medium and large size companies.

Jan 1, 1999

By A. H. Tousley, L. H. Gee

Until comparatively recently, the gypsum industry has been slow to change, often clinging to old processing methods developed a generation ago. Now, however, a highly competitive market has forced gypsum companies to concentrate on devising methods to reduce material and operating costs and improve product quality. In one such effort, Kaiser Engineers recently designed and constructed two modern gypsum plants for Kaiser Gypsum Co., Inc., incorporating centralized control, automatic sequence starting, mill amperage control of the roller milling systems, automatic calcining in kettles, and rapid mechanical stucco cooling. Fig. 1 shows the control panel for the calcining departments at wallboard plants located in Jacksonville, Fla., and Delanco, N. J. In each instance the calcining department (commonly known as the "mill") sets the basis for the quality control for the entire gypsum plant.

Jan 12, 1966