Search Documents

By P. Schloth, H. van Swygenhoven, N. Chobaut, J-M. Drezet

"In the current trend toward thicker aluminium plates, a major concern is the stress build-up during quenching which causes distortions during machining. Indeed, cooling rates are not high enough, especially at the core of such thick plates, to prevent any precipitation and quench induced precipitates lower the hardening potential. Multi-scale modelling is required when predicting macro-scale stresses after quenching for thick heat treatable aluminium components. The reason is the instantaneous strong coupling between phase precipitation at the nano-scale and material hardening due to precipitation or softening owing to solute depletion at the microscale. For thick parts, quenching intensities decrease when going from the skin to the core of the component, thus introducing a gradient of nanostructure and consequently a gradient of mechanical properties. In addition, large thermally induced deformations lead to high macroscale residual stresses although part of them is relaxed by plastic deformation. These stresses have been measured in water quenched thick plates of 7040 and 7449 aluminium alloys using neutron diffraction and layer removal techniques and the results when compared with a thermomechanical finite element model of quenching highlight the influence of precipitation.IntroductionIn the processing route of heat-treatable aluminium alloys (AA), a critical step is quenching from the solutionizing temperature. High cooling rates are desired, as they avoid formation of coarse precipitates, which reduce mechanical properties. Fast quenching, however, cannot be achieved in the centre of thick components, where the quenching rate can be more than one order of magnitude lower than at the surface. The existence of a thermal gradient between core and surface leads to a differential thermal deformation which is accommodated by elastic and plastic deformation to comply with the compatibility of deformation. Whenever the material yields, especially at high temperature when the yield strength is low, residual stress remains after quenching due to the irreversibility of plastic deformation. After quenching, the plates are in a state of residual stress that causes unacceptable distortions during machining and may reduce service life drastically. Since stress relaxation is negligible during ageing treatments [1 ], agehardened aluminium parts are usually stress relieved prior to ageing. This is typically achieved by applying plastic deformation: stretching from 1.5 to 3 % in the rolling direction (L) can reduce the internal stresses by a factor of approximately 10 [2, 3]. However, complex geometries or thicker components like thick sheets require other approaches. Reducing the quenching rate by using boiling water for instance leads to lower residual stresses [1, 4]."

Jan 1, 2013

By C. L. Brown

Coal has been transported by belt conveyors in mines for many years; however, only since the beginning of the general mechanization period have complete transportation system of this type been employed. Aside from my complete belt-conveyor transportation systems, belt conveyors are frequently used in conjunction with other transportation. Many early installations, for the most part, were made without standards as a guide. As a result, some States have outlined certain requirements based more or less on experience following mine fires. Correlation of these regulations should result in more uniformity in connection with standardization of regulations. The National Electrical manufacturers Association has published standards for mining-belt-conveyor installations2/ that should be helpful to the coal-mining industry generally. Bureau of Mines Schedule 2F3/ requires certain controls for permissible-belt- conveyor drives, and similar requirements are listed in Bureau of Mines bulletin 514.4/ Committees of the American Mining Congress have prepared much valuable information concerning operation of belt conveyors, and a subcommittee on fire-resistant belting has been active. 5/

Jan 1, 1956

By Marco Sonnenschein

Belt conveyors for tunnelling are industry standard and key to high performance of TBM drives. Conveyors reduce traffic in the tunnel and increase safety in the tunnelling process. This paper will illustrate the state of the art of tunnel belt applications in very long and curvy tunnels like the Coxwell Bypass Tunnel Project in Toronto, Canada.

Jun 23, 2024

By D. Chakravarty, B. Samanta, D. Ghosh

Autonomous robots are useful for 3D underground mine mapping to avoid human exposure to hazardous spaces. To prepare a precise mine map, a self-navigating robot must navigate an arduous path, avoiding obstacles and sensing the environment. A prototype laboratory-scale robot was built and evaluated through a mock-up in a test mine gallery. It was outfitted with a 2D laser scanner, a stereo camera for obstacle avoidance, and a high-precision, laser-based imaging and digitizing system for collecting 3D point cloud data. Various algorithms were used for scan matching to facilitate simultaneous localization of the robot for mapping.

Jan 1, 2014

By Robert J. Timko

This U.S. Bureau of Mines study examined spontaneous heating episodes in coal mine pillars in an active underground coal mine. The information obtained from these incidents was then analyzed to learn which sampling methods provided the earliest indication of pillar heating. The objective of this study was to discover if the location of future events of pillar spontaneous heating could be inferred from the available information. The spontaneous heating-prone area in this evaluation involved pillars located just inby the mine portals. Several detection methods were used to determine gas levels outside as well as inside the affected pillars. It was hoped that, by incorporating external and internal sampling methods into an organized pro-gram, locations undergoing spontaneous heating could be determined more readily. This study found that by drilling small-diameter boreholes into the pillars, then obtaining gas samples from the affected pillars, the ability to locate early spontaneous heating episodes was improved. However, the ability to accurately predict future spontaneous heating events remains in question.

Jan 1, 2010

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels.This paper analyses the reasons for the inadequate level of pro-active plant maintenance practice in industry today, and presents a number of important criteria in selecting appropriate solutions to this problem. A case study of a specific real-time, remote equipment management application is presented."

Jan 1, 2003

By Kenneth L. Bickel

During an underground mine fire, the importance of controlling the spread of smoke and toxic gases with suitable ventilation structures has been proven. However, under certain conditions, control of the propagation of the fire itself may be even more critical in insuring a safe mine evacuation. Fire doors offer the means for accomplishing both objectives. In 1978, the Bureau of Mines initiated research to evaluate the state of fire-door technology and develop and test a fire door suitable for large openings (10 by 12 ft or larger) in noncoal underground mines. This report discusses current fire-door technology in the context of the underground mine environment and the design, fabrication, lab testing, and in-mine field testing of a mineworthy fire door. This door has a 1.5-h fire resistance rating and limits temperature rise across the door to 2500 F during the first 30 min of fire exposure.

Jan 1, 1987

By E. B. Nelson, B. W. Gandrud, B. M. Bird

"The Lewisburg No. 2 mine of the Sloss-Sheffield Steel & Iron Company is located in Jefferson County, Alabama, about 7 miles due north of Birmingham. At this point the coal from the Mary Lee seam when coked in by-product ovens yields an excellent quality of metallurgical coke suitable for use in the iron blast furnace; it is also an excellent steam coal. In mining, all three benches are worked. Coarse impurities are largely gobbed by the miners underground.In addition to giving the data obtained from screen-sizing and float-and-sink tests of a representative sample of the raw coal, this report presents the results of slotted-screen tests to show the proportions of flaky particles in selected sizes, and the results of tests to show how much coal is liberated from impurities by crushing the coarsest sizes. These data have been obtained in connection with an extensive study of coal-washing now being conducted by the U. S. Bureau of Mines and the University of Alabama, with U. cooperation of the different operators of Alabama. As the work progresses other reports will follow containing furtner data on the washability both of the Mary Lee seam and of other seams in Alabama and giving the results obtained in preparing these coals by various methods.Although a great amount of investigative work on the preparation of the Mary Lee scam was previously carried on by the various coal companies of the district, comparatively little of this information has been published. In governmental publications three references have been found. Forbes5 gives a number of sections with proximate and ultimate analyses of face samples taken in the mines. Gandrud and Britton'' show sections of this seam at Flat Creek and New Castle; they also give the specific gravity and ash contents of the partings of coal and impurities. In their paper Yancey and Fraser7 include washability studies and washing data from the Sayreton mine of the Republic Iron & Steel Co."

Jun 1, 1930

By O. A. Carson

Introduction Although the equilibrium conditions of the copper-tin alloys have been the subject of a ?great amount of research, the equilibrium diagram is still in doubt. The first systematic investigation of the series was made in 1894 by Le Chatelier, who published a freezing-point curve. In 1895, Roberts-Austen and Stansfield published the complete liquidus and partial solidus curves, which they modified somewhat in 1897. Their liquidus as given in 1897 is essentially that accepted today (Figure 3). Haycock and Neville also published a liquid us curve in 1897. In 1898, William Campbell published a series of micrographs showing the changes in microstructure which accompanied the thermal changes of Stansfield? s diagram. The classic work on the bronze series was published by Heycock and Neville in 1903. Their diagram was based on both thermal and microscopic evidence, and is the first for this series of alloys which can be considered nearly complete. Further, it was the first bronze diagram in which any attempt was made to apply the phase rule in the interpretation of the thermal and microscopic results. That portion of Heycock and Neville's diagram covered by the present work is reproduced in Figure 7.

Jan 1, 1929

By Michael Forrest, John Roadifer, Glen Gorski

"The Calaveras Dam Replacement Project (CDRP) requires large disposal sites to store excess excavated materials that could not be utilized for dam construction. Because of access restrictions during design, the disposal site rockfill toe dike area at the edge of the reservoir could not be explored to evaluate soil conditions. As such, the site had to be explored as part of the construction contract. Exploration revealed very soft clay and loose silty sand up to 40 feet thick that would not be able to support the rockfill dike at the toe of a large disposal site fill. Several alternatives were evaluated to stabilize these soils. Based on constructability, cost and risk considerations, cement deep soil mixing (CDSM) was selected as the preferred method of soil stabilization. The challenge was to design and construct the CDSM stabilization to minimize construction delays. A joint effort by the design engineer, construction manager and contractor achieved CDSM stabilization in about three months, from design through completion of construction. A rigorous quality control program included compression testing of both wet grab and cored soil cement samples to demonstrate that specified strength requirements were being achieved.INTRODUCTIONDisposal Site 3 (Figure 1) is one of the primary CDRP disposal sites having a height of 240 feet and a storage capacity of about 2,500,000 cubic yards. An approximately 40-foot-high rockfill dike at the base of the disposal site provides an erosion resistant toe for the disposal site. The rectangular foundation area shown in red was not able to be investigated during design because of access restrictions."

Jan 1, 2015

By R Nicholson, N D. Cox, N W. A Lambert

"This paper reports on the long-term operation of a particle density meter (PDM) at the Bloomfield coal handling and preparation plant (CHPP). This unit has been operating continuously for over three years, providing real-time data to the operators to allow the monitoring of flotation circuit performance. PDM outputs include slurry density, solids concentration on both mass and volumetric basis, and particle density. Knowing the average particle density of a stream allows for the optimisation of the process in real-time.The calibration of the solids concentration measurement device proved very difficult as the factory calibration techniques and existing laboratory analysis did not give accurate or reliable results. The solids concentration device had to be re-engineered and a new calibration method developed that gave accurate and repeatable results. Independent verification of samples taken from the PDM was undertaken as part of the trial process.The operational reliability of the PDM was a major point of investigation. The initial installation of the unit revealed issues with large, misplaced material of up to 20 mm periodically entering the unit, leading to feed blockages. The presence of these misplaced, oversized particles in the flotation circuit was resolved by installing innovative automatic back flush systems on the PDM.From a plant perspective the PDM has been an invaluable instrument that has enabled irregularities in the flotation circuit performance to be identified, which sampling had not and could not readily identify. This was achieved by close monitoring of real-time tailings composition on a minute by minute basis over short and extended periods. Variations in the tailings stream with respect to particle density and solids concentration were traced back to other issues in the plant. In addition, the PDM has allowed cell optimisation with respect to reagent dose rate to be improved. The PDM with real-time feedback can negate the need for large sampling campaigns and analysis during plant optimisation programs.Citation:Lambert, N, Cox, N and Nicholson, R, 2016. Particle Density Meter, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 245–250 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Darin Cotton, Tim Burgess, Tim Martin

"As the leading US supplier of roof control drills, J. H. Fletcher and Company® has encountered an extensive set of roof strata challenges and has overcome various drilling issues by varying machine parameters and working with customers and tool manufacturers to develop solutions. Every mine wants to drill and install roof bolts as fast as possible with maximum safety at the lowest possible installation cost for their conditions. In most circumstances, the intuitive method of higher speeds and pressures can actually have a detrimental effect on the roof drill safety and performance.This paper will outline recent tests carried out at several different coal mines in the Eastern United States. The tests focused on optimizing the drilling parameters of feed pressure, feed rate, rotation speed, and drill torque.The drill feed, rotation speed, and rotation torque, as well as the type of bit selected, have a definite impact on the performance of the roof drill including drilling speed, safety, and tool life. The drilling process can be improved while also improving operator safety and reducing bolt installation costs by maintaining the appropriate roof drill settings for the specific strata conditions.The advantages of improving the drilling process includes increased bit life, increased drill steel life, reduced hanging drill steels, reduced clogging of the vacuum system, decreased whipping drill steel potential, reduced noise generation, and increased cutting size which reduces fine dust generation and dust collection system servicing.INTRODUCTIONIn recent times, the economic pressures that coal producers are facing have created an increased emphasis on controlling operating costs. Several coal operators have pointed out their dissatisfaction with low bit life, and there is a renewed interest in improving tool life and machine performance as part of an overall cost control strategy. Operators are looking for ways to reduce tooling cost, maintenance costs, and drill downtime without decreasing drill performance. This renewed interest in reducing operating costs, along with the ongoing desire to improve safety, created a perfect environment to take a fresh look at the existing fleet of machines to see what could be accomplished. The goal was to take a practical approach to reviewing machine parameters to determine what changes could be made. The emphasis was on changes that would be feasible to roll out to an entire fleet of machines in a short period of time with minimal capital expenditure. The thought process was that significant improvements could be made by simply tuning up the machine parameters to provide a more efficient and safer bolting process."

Jan 1, 2015

By Martin Hertzberg

In this Bureau of Mines study, an equation is derived for the limit burning velocity for divergent, spherical propagation from an ignition kernel of radius, r: (Su)e = ( ) . For flame propagation into a preexisting, stretching velocity gradient of magnitude dv/dx, the limit velocity is (Su)e = (a dv/dx)1/2. These formulations are shown to be equivalent to the fluid dynamic concepts of Damkoh1er, Kar10-vitz, and Markstein. Existing data for the b10woff limits of flames are shown to give excellent agreement with those concepts provided that proper account is taken of two dilution effects: composition dilution caused by entrainment and velocity gradient dilution caused by flow expansion. Approximate flow-field solutions are also derived for the unburned gas motion above an upward propagating, spherical flame kernel in buoyancy-induced flows. It is shown that;, the upward hemisphere propagates toward a stagnation plane in a counterflow configuration involving the balance between the combustion force, which accelerates the cold gas upward, and the buoyancy force that accelerates the cold gas downward. The position of the stagnation plane above the upward propagating hemisphere is related to the ratio of the buoyant velocity, vb, to the burning velocity, Suo Extinction of the upward propagating wave occurs by flame stretch in that counterflow configuration when n = Vb/Su begins to exceed the expansion ratio, Pu/Pb' and the wave is blown off by its own buoyancy-induced flow field.

Jan 1, 1984

By Michael. H. Moys, Clayton Bhondayi

An electro-resistive measuring technique developed by the authors was used to study the effects of superficial gas velocity and froth height on froth phase bubble sizes as a function of height above the pulp-froth interface. Flotation tests and the bubble size measurement were carried out in a laboratory mechanical flotation cell that was operated in a pseudo-steady state mode using primary rougher tailings slurry from Lonmin Platinum as feed. The values of intra-bubble impact distances (IIDs) which are the estimates for froth phase bubble sizes obtained from the measurements indicated that as superficial gas velocity was increased, the values of IIDs decreased for the two froth depths tested. Increasing froth height at fixed gas rate resulted in an increase in IID values especially close to the froth surface. Changing froth height and gas rate alters froth residence times; longer froth residence times mean more time for bubbles to coalesce hence larger values of IIDs and vice-versa.

Jan 1, 2014

By Christopher Gammons

In developing countries throughout the world, gold ores are being processed by mercury amal-gamation, a technique long banned in the U.S. - unless a retort operation is used for mercury recovery - due to mercury toxicity and its effects on the environment. Amalgamation is a simple process that involves contacting a ground, slurried concentrate or ore with mercury in a slightly agitated vessel, usually for several hours, The amalgamated mercury is separated by gravity and then filtered through a fine cloth to collect the gold amalgam as a sponge, which is then fired to remove the final remnants of mercury and produce high quality gold. However, in Peru and other developing countries in South America and throughout the world, tailings are simply discarded into uncontrolled drainages and ponds and the sponge is fired in the open air. Clearly, in this case, environmental friendly and, to make matters worse, is typically conducted by family members of all ages without proper protection. Furthermore, the technique is inefficient, yielding approximately 50% gold recovery. For the past two years, faculty members from Montana Tech in Butte, MT, USA and the Universidad Nactonal del Altiplano in Puno, Peru have teamed to study the La Rinconada Mine Complex located in southern Peru approximately 100 kilometers north of Lake Titicaca and 25 kilometers west of Bolivia. The mining complex is over 5,000 meters above sea level and exists at the foot of a receding glacier in the Andes Mountains. A suite of soil and water samples collected in 2001 documented extensive Hg contamination in the Rinconada area [1]. The present paper summa¬rizes a follow-up investigation in July-2002, in which water samples were collected at numerous locations along the 200 km length of the Rio Ramis, from the Rinconada mine com¬plex to Lake Titicaca, In addition, we report new results of Hg analyses of fish from Lake Titi¬caca, The results of this study have relevance to safety and health concerns for the miners as well as people in downstream communities.

Jan 1, 2003

By John J. Mulligan

Since 1941 the Federal Bureau of Mines has been conducting an intermit-tent program of placer and lode investigations to evaluate the potential tin resources of the western Seward Peninsula tin belt. Previous investigations were made in the Potato, Cape, Brooks (Lost River), and Ear Mountain areas. As part of this program the Bureau made a reconnaissance of reportedly tin-bearing stream gravels in areas adjacent to the previously worked tin deposits at Lost River and Potato Mountain. The objective of the reconnaissance was to determine if additional areas might be favorable for lode or placer exploration. The work was begun late in the fall of 1956 and completed during the following summer. The streams sampled were the Lost River and York Creek in the Brooks Mountain area and the Anikovik River and Kigezruk and Baituk Creeks in the York area. Samples were obtained by churn-drilling methods employing conventional placer-evaluation procedures. Holes were drilled at wide intervals at sites chosen as being representative of drainage areas rather than of individual gravel deposits. Minor to trace amounts of tin were found in the gravels of all these streams, but the highest grade was 0.35 pound of tin per cubic yard in the gravels of Lost River below the mouth of Tin Creek. Small amounts of gold were found on Baituk Creek and in one hole on the Anikovik River; the highest grade did not exceed 10 cents per cubic yard. Traces of scheelite and barite were found on York Creek, chromite was encountered in one hole on the Anikovik River, and minor amounts of titanium minerals (probably derived from basaltic intrusives) were found in the York area.

Jan 1, 1959

By Walter E. Lewis

This circular presents the method of making tests and apparent results of comparing performance of tungsten carbide insert bits and steel detachable bits by the Cleveland-Cliffs Iron Co. at the company's mines on the Marquette iron range of Michigan. The mines are at Ishpeming and Negaunee, Mich., and include the Cliffs Chaft, Mather "A", Cambria-Jackson, and Mather "B". There are four general characteristic types of high-grade iron ore on the Marquette range. B. H. Boyum2/ classifies the Cliffs Shaft as "hard-ore" and the Cambria-Jackson and Mather "A" as "soft-ore" types of deposit. Shaft sinking through Jasper, slate, and graywacke was in progress at this writing at the Mather "B", with completion at 3,100-foot depth in August 1949. The many different kinds of rock and ore at the mines of the Cleveland- Cliffs Iron Co. and the experimental work being carried on with carbide in- sert bits make it possible to compare, generally, the carbide insert and steel detachable bit. The type of "hard ore" at the Cliffs Shaft mine re- quired close study of the possible use of the insert tit, and their records are more complete than those of the "soft-ore" mines. History and development of tungsten carbide tips inserted in rock drill bits have been covered by R. W. Adamson, C. H. Vivian, R. C. Sullivan,5/ and others. Tungsten carbide insert rock bits have only recently been introduced to the domestic mining industry. Although unusual performance records are being reported at operations employing the insert bits, the general adaptability of the tool to all rock types and the advantages to be gained by using carbide insert tits remains to be demonstrated. Insert-bit performance is being observed at numerous mines and quarries throughout the United States The several mining operations at the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., is one site where exhaustive comparative tests of insert and conventional steel detachable bits are currently in progress. Results to date are sufficiently impressive to be of general interest to the mining

Mar 1, 1950

By Gilbert R. Tallard

"Pouring deep foundations by the tremie pipe method is nowadays such a common process that it has becomes an unspecified practice. Means and methods are almost entirely at the contactor’s discretion. A variety of practices are permitted and seldom associated with the discovery of abnormalities and areas of random defects in concrete. This writer wishes to call the attention of stakeholders to the initiation details of the tremie pour operation.KEYWORDSINTRODUCTIONThe advent of slurry as a means of shoring an excavation of relatively small cross section but of possibly great depth has become part of state of the art in foundations construction, with the substitution of said slurry by concrete to provide the structural end product element through the use of tremie pipes. In appearance, there is nothing more simple than pouring concrete into a tremie pipe through a hopper after the basic work has been done i.e. the excavation or drilling, the cleaning of the slurry, the placement of the reinforcing cage, then the tremie concrete pour is almost a reward for a successful achievement. Force of habit has removed the awareness on the process fundamentals for initiating the pour; a variety of practices used call for a review and a reassessment as a means of reducing construction defects that may result from flawed practices, and and especially we are pouring deeper holes. This writer intends to address this issue focusing both on the drilled shaft and the diaphragm wall industries.TREMIE PIPES AND HOPPERSA tremie pipe diameter needs to be sufficiently large to allow the rapid descent of concrete with a minimum of friction loss and avoiding possible bridging in relation to aggregate size. Impervious joints between pipe sections are essential to prevent slurry “raining” over the concrete which can cause concrete segregation pockets and possibly plug the pipe with damaging consequences. That tremie pipes be long enough to reach the bottom may be self-evident but poorly written specifications can be erratic on that subject and seldom specific in terms of inches. A standard pipe of 10 inches is well accepted throughout the foundations industry; double O rings and spline joints are common and function well if properly maintained. However the practice to cover the joint with the ineffable duct tape indicates that all is not always well with this detail. Also, spline cables may shear in case of very long tremie pipes causing the separation of the tremie pipe requiring a restart in midstream with another probable source of inter mixing of concrete and slurry with subsequent defects."

Jan 1, 2017

By Richard I. Barnhisel

At the Sinclair Study Site it was found that the deeper the soil the greater the yield of corn, soybeans, wheat, alfalfa, and timothy. Yields at this location were generally lower than those at the Alston Surface Mine. At Alston the non-prime land treatments generally produced greater yields for all crops than did the prime farmland treatments, however, the intermediate soil thickness, 20 cm topsoil over 40 cm of subsoil, gave the best yields, provided it's subsoil had been limed. From a chemical point of view, acidic spoils do not need to be buried by 120 cm or 4 feet of soil, provided adequate lime is applied to these spoils as a barrier prior to placement of good quality topsoil and only forage crops are to be grown. The burial depth must be increased to as much as 75 cm when grain crops such as corn or soybeans are to be grown. This response to burial depth appears to be related to water storage needed by the crop and not due to toxic effects of the spoils. A conventional farm tractor-mounted subsoiler increased yields of soybeans and corn the first one or two years, but the effect was diminished with time. Subsoiling did not produce significant increases for alfalfa or wheat. However, ripping with a bulldozer produced significant yield responses, especially for corn and soybeans, that have lasted for at least three years. The ripping effectively reduced the bulk density at least within the zones through which the ripper had passed. Liming the upper 20 cm of subsoil significantly increased yields of alfalfa, corn, and soybeans. There also appeared to be an interaction between this lime treatment and soil depth. Yields of some grain and forage crops may be high enough to meet target levels for bond release for prime farmland. Based on the present study, one should not expect corn yields to be high enough to meet bond release. This statement should not be considered final since the experiment is not complete.

Jan 1, 1983

By Meisam Ghiasi, Mohammadreza Khalesi, Mahmoud Abdollahy

In the current research, isothermal experiments of kinetic analysis were performed at different temperatures (800–1050 °C) and particle sizes (885 to 10,763 μm) to investigate the calcination kinetics of high-purity limestone. Thermal analyses were carried out in a zirconia crucible, 1 cm in height, for different temperatures and particle sizes. The reaction rate coefficients were varied in the 2.2 × 10−5-1.62 × 10−3-m0.6.s−1 range. Moreover, various isothermal kinetic analysis methods were applied to assess the decomposition mechanism and the calcination function governing the process. The modified shrinking core model was found as the best representation of the high-purity limestone kinetic data. The activation energy was evaluated using the Arrhenius curve, and an average value of 86 kJ.mol−1 was obtained.

Sep 15, 2020