Search Documents

By Albert L. Toenges

This paper is the third of a series4/ that describes some methods and practices of mining coal mechanically where operations are conducted on more than one shift. The mining of coal by means of mechanical devices has emphasized the need for continued study of the relationship, of these devices to existing physical conditions and to planning of the operations for increased safety and economy. The purpose of this investigation is to stud the operations of different types of mechanization used in mines under various systems of mining and physical conditions to reach conclusions as to the safest and most economical methods and practices of mining. Physical conditions very in different and in the same mining districts and determine, together with economical conditions, the systems of mining and the types of mechanical loading equipment used. The information presented in this paper

Jan 1, 1941

By C. H. Kats, E. G. Meiter, J. J. Bloomfield

"INTRODUCTION.Street manholes for underground power and signal circuits, and for sewers vary in size from small openings that a workman can enter, to large central vaults. As the gas hazards in manholes are similar to those in mines, the mine safety committee of the Bureau of Mines was asked whether the miners' flame safety lamp is a practicable device for indicating inflammable gases in manholes.The coal miner detects firedamp (methane or CH4) with his flame safety lamp by observing the luminous can or the increased length of flame that appears when 1.5 per cent or more of the combustible gas is present. The lamp flame also warns him of lack of oxygen by going out when the oxygen becomes less than 16 to L7 per cent. A tentative rule regarding the proposed use of safety lamps at manholes has been suggested previously as follows: ""Testing for gas: Do not enter manholes until you have .assured yourself that the manholes are free from dangerous gases, by testing with an approved safety lamp, by ventilation, or by other adequate methods."" The Bureau's committee recommended that miners' flame safety lamps are not suitable,testing in manholes because hydrogen gas may be formed therein. The flame safety lamps approved by the Bureau of Mines for use in aseous mines are safe in presence of methane and while not tested against the members of the paraffin hydrocarbon series (CnH2n+2) higher than methane they been have been used therein; the lamps should not be used in hydrogen or acetylene they can initiate explosions in presence of these gases."

Oct 1, 1925

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

By Geoff Matthews, David S. Wong, Linda Wright, Pretesh Patel, Mark Dorreen

This paper examines the development of the new EnPot heat exchanger technology for aluminium smelters and the potential impact it could have on the sustainability and economics of primary aluminium production. The EnPot technology can be used to help the aluminium smelting industry be part of the solution to accommodate increased intermittency in our future renewable energy generation, post COP 21. The EnPot system provides for the first time, dynamic control of the heat balance of aluminium smelting pots across the potline, so that energy consumption and aluminium production can be increased or decreased by as much as plus or minus 30% almost instantaneously. This enables a new way of thinking to emerge when considering the relationship the aluminium smelter plays in connection to the power grid. The EnPot technology provides smelters with the means to free up power back to the grid, transforming the smelter from only an end user of power into a ‘virtual battery’ for the electricity network. This fundamentally changes the way electricity is consumed by the smelter and is a concept already being tested by several smelters.

Mar 1, 2017

By James F. O?Neil

Brown iron ore deposits in Quitman County, Ga., were investigated by the Federal Bureau of Mines in cooperation with the State of Georgia, Department of Commerce, and the University of Alabama. Ninety-one holes were drilled, having an aggregate footage of 2,188 feet; seventy-one holes penetrated 248 feet of iron mineralization. Average thickness of the ore zone was 3.5 feet under an average thickness of 14.7 feet of overburden. The drilling developed inferred reserves containing nearly 30 million long tons of crude ore with an average analysis of 28 percent iron plus minor quantities of manganese. Test work done by the Bureau on the crude ore samples indicated that they would upgrade by current lug washer practice, with the use of a 1i8-inch screen, and yield 4.4 million dry long tons of concentrate with an average analysis of 52.1 percent iron plus manganese. The weight recovery obtained was 14.7 percent. Research studies made by the Bureau showed that the weight recovery would be increased by changing the screen size without any appreciable sacrifice of grade. The average weight recovery was increased to 18 percent with a 10-mesh screen and 22.8 percent with a 20-mesh screen. Screen tests studies indicated that there was no appreciable interlocking of the iron and manganese minerals and the clay and silica waste particles of the materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size.

Jan 1, 1965

By W. L. Acherman

Molybdenum, tungsten, and vanadium were found by the Bureau of Mines to possess generally superior chemical and galvanic corrosion properties in many aqueous corrosive media at temperatures up to the boiling point. The corrosion resistance of vanadium in certain solutions was further improved by alloying it with such metals as columbium, tantalum, and titanium. was susceptible to a type of crevice corrosion in mercuric chloride solutions, but no other instances of crevice corrosion were encountered. With few exceptions, molybdenum, tungsten, and vanadium were not adversely affected when coupled with dissimilar metals in galvanic corrosion experiments; in some cases one or both members of a couple were protected by contact. When exposed to aqueous ammonia spray at 60° C, all three metals were attacked, but they were moderately resistant in spray environments of substitute ocean water and ammonium dihydrogen phosphate.

Jan 1, 1966

By J. R. Long

The investigations described herein are concerned with a portion of a systematic research, by the Federal Bureau of Mines on ductile titanium. The Bureau's work on the metal has resulted in development of a semi commercial process for the preparation of titanium and has also made available significant information on the fabrication and physical properties of this new strong, light, corrosion-resistant metal. Considerable interest has been aroused by this work, and a number of other laboratories have begun similar investigations. However, the necessity for Consolidating titanium by normal powder metallurgy methods presents difficulties in producing commercial forms and shapes on a large scale. This investigation was therefore undertaken for the purpose of improving the technique for consolidation of titanium powder into solid nonporous metal.

Jan 1, 1949

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union and the United States are summarized. Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1978

By G. A. Kordosky

Solution mining followed by solvent extraction-electrowinning (SX-EW) is one possible way to economically extract copper from ore bodies which cannot otherwise be profitably exploited. Published costs for the unit processes of SX and EW are out of date especially in view of the newer reagents now available and the newer circuit configurations, This paper updates the costs for SX-EW in 1985 dollars and also discusses some of the trade-offs which must be made when designing an SX-W plant.

Jan 1, 1986

By Joshua Hoffman

The recruitment and retention of future talent into the explosives industry is becoming increasingly important. Student chapters help with this effort but what are they doing and are there things they could learn from each other? This paper discusses the University of Kentucky Student Chapter's efforts to grow membership, retain its recruits, and integrate them into the explosives industry. Several social and professional events during which the students are able to meet and network with members of their future industry are introduced. The special relationship that has been fostered between the University of Kentucky and Missouri University of Science and Technology is discussed. Professional development initiatives which are critical for a student to become vested in the industry are shared in this paper. These opportunities which range from internships to research positions allow a person to get a better understanding of the explosives industry and find the niche that best suits them. Many of the student chapters are closely connected with engineering programs. While this makes sense and both entities benefit from these arrangements there is a trend of job placement primarily in the engineering industry. By providing these students with the chance to learn more about the explosives industry and get hands on experience more of these future engineers and professionals can be retained after their graduation.

Jan 1, 2013

By C. A. Young

In-situ Fourier transform infrared/internal reflection spectroscopy (FT ?IR/IRS) has been extended to study oleate adsorption at a calcite surface. The birefringent and transmission limitations of calcite were overcome by using an appropriately designed optical setup and a near-infrared (NIR) spectrometer. An adsorption isotherm was determined at pH 9.2 and room temperature. Comparison with the fluorite/oleate adsorption isotherm determined by the same technique indicates that oleate abstraction by calcite can be as much as one order of magnitude larger than that by fluorite. Nevertheless, the hydrophobicity of the fluorite/oleate surface is greater for equivalent adsorption densities as indicated by contact angle measurements and flotation results. The monolayer region has been confirmed to be chemisorbed oleate at both calcite and fluorite surfaces. Furthermore, multichannel laser Raman spectroscopy (MLRS) showed that chemisorbed oleate at the fluorite surface undergoes a double-bond reaction with oxygen to form an epoxide/polyether complex. Such a reaction, however, could not be detected at the calcite surface. These phenomena are discussed in terms of the intrinsic surface properties of the mineral systems as well as the adsorption density and the cross-linking/polymerization reaction of the adsorbed oleate film.

Jan 1, 1993

By Steven K. Ruggieri

Increased coal production on longwalls has brought with it higher levels of dust generation. Most U.S. longwall mining operators have difficulty complying with Federal dust standards, which are stricter than European standards. Longwall operators faced with a longwall that is "out of compliance" have implemented a variety of practices designed to reduce dust levels. Mining conditions and other important variables, however, can cause fluctuations in dust levels that may overshadow the performance of a new dust control technique. This can result in the continued use of an ineffective technique or lead to the abandonment of an effective dust control technique. No single technique can keep a longwall in compliance. Maintaining compliance requires a fundamental approach to dust control -- proper application and continued use of effective dust control techniques.

Jan 1, 1983

By E. M. Wilde

Through the USGS's National Coal Availability program, coal resource appraisals have been completed for three 7.5-minute quadrangles (Willow Crossing, Colstrip East, Colstrip SW) in the Powder River Basin area of southeastern Montana. Available coal reserves (original reserves minus tonnages affected by current restrictions) vary from 44 to 70 percent of the original reserves. Major restrictions impacting each area also vary. In each area, one or two beds contain most of the reserves, but up to eleven beds contain available coal. The main beds in completed studies are the Knobloch, Rosebud, Sawyer and Flowers-Goodale. Three additional areas (six 7.5-minute quadrangles) are in preparation.

Jan 1, 2001

By J. S. Hansen

In support of its objective to conserve mineral resources by minimizing premature failure of materials, the Bureau of Mines conducted a cooperative study with the U.S. Department of Energy on the erosion and abrasion resistance of hard materials for valves in coal conversion systems. This report describes a newly developed erosion-testing apparatus and presents data on the erosion resistance of over 200 materials. Erosion resistance of most metals was comparatively low. In contrast, ceramics and cermets such as B4C, WC, SiC, Si3N4, and TiB2, when fabricated to minimize porosity, displayed greater than five times the erosion resistance of metals. Coatings such as boron diffused into Mo and WC, chemical-vapor-deposited TiCN, and electrodeposited TiB2 were highly erosion resistant if applied in thicknesses ranging from 60 to 75 µm. Erosion resistance of cemented carbides was inversely related to metal binder content.

Jan 1, 1979

By N. Syna

The selection and preparation of activated carbon suitable for specific application can often involve exhaustive adsorbent preparation and testing. This work examined an emerging technique based on modelling the correlation of observed adsorption capacity to the carbon characteristics as a means of decoupling the roles of carbon textural and surface chemical properties. The insights to these specific roles are then used in tailor-making adsorbents and in establishing the optimal carbon properties for specific application. In this study, a series of activated carbons prepared from bagasse by physical and chemical techniques and commercially available carbons were used in developing the models. These carbons were tested for the adsorption of thiourea-gold (I) chloride complexes. Thiourea is an important alternative gold lixiviant with the potential to address current ecological and safety concerns in the extraction of gold. A four-component model, which correlated the adsorption gold capacity to carbon textural and surface chemical properties, was proposed. The model fit was assessed using multi-linear regression and a partial F-test. This was followed by goodness of fit test achieved through r2, adjusted?r2 and mean square error (MSE) values. The results suggest the adsorption of the gold-thiourea complex is strongly influenced by the internal surface area and pH of the carbon. Tailor-made activated carbon from bagasse showed adsorption gold capacities of up to 198 mgAu/g adsorbent, demonstrating the potential of bagasse as a precursor for gold adsorbents and of this empirical modelling approach in developing adsorbents for metal recovery.

Jan 1, 2014

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021

By Y. He

Early research showed that the separation of particles based upon their density was not possible in steadily rising air streams. The terminal velocities of moving spheres are determined by their aerodynamic characteristics. This prevents particle separation by density in standard air classifiers. Passive pulsing air classifiers have accelerated airflow in certain regions, which achieves density-dominant separation. Numerical simulation of airflow within passive pulsing air classifiers was done to estimate airflow patterns near a damper. Analysis of those results shows the significant acceleration of the airflow above the damper. Laboratory trial separations have shown that passive pulsing classifiers are superior to standard air classifiers. Keywords: pulsing airflow, passive, simulation of airflow models, acceleration effect, density

Jan 1, 2005

By Farzaneh Abedini, Narain Hariharan, Lucas C. McFarlane, Nikolas A. Romaniuk, Tiffany Thayne

The use of dewatered mine tailings as backfill material (commonly referred to as ‘paste’ backfill), is the most practiced form of backfill in Canada providing significant environmental benefits by reducing the size of external tailings facilities and improved economics through enhanced resource recovery. Paste backfill operations reuse filtered mine tailings with a cementitious binder and water to create a slurry that is hydraulically transported to refill underground stopes, later forming a structural network of cemented tailings in the mine stopes. Unlike typical structural applications that utilize General Use (GU) Portland cement; modern paste backfill operations maximize strength performance by blending Portland cement with ground granulated blast furnace slag (GGBFS) or other supplementary cementitious materials (SCMs). GGBFS and other SCMs offer key performance benefits and carbon reductions; however, the availability of these SCMs is rapidly dwindling in today’s carbon-constrained economy. This paper examines the development of an alternative binder system that provides similar performance and carbon reduction to that of GGBFS for mine backfill operations. The binder utilizes the chemical reaction between a reactive source of aluminosilicates and available calcium from calcium oxide or calcium hydroxide to replace between 50 to 100% of GGBFS. The performance of the binder is examined with insights into the hydration mechanisms that generate mechanical strength in the cemented paste network. Paste backfill slurries require precise engineering to create a material that maintains flowability during pipeline transport and generates enough strength to meet operational targets once placed in the stopes. Engineering of such slurries requires large amounts of water to be added to the binder-tailings matrix, far exceeding the typical water to binder ratios used in concrete mix designs. This characteristic of paste backfill warrants great emphasis on understanding the hydration mechanisms of the binder used in the paste backfill system. GU cement is typically composed of 50-70% tricalcium silicate and 15-30% dicalcium silicate.  The hydration mechanisms of these compounds consume 4 to 6 units of water to mineralize into calcium silicate hydrate cemented phases that result in compressive strength development. Cementitious aluminate and aluminosilicate phases make up 5-20% of GU cement and aid in secondary performance characteristics such as set time. Certain calcium aluminate hydrate phases such as monocarboaluminate and ettringite mineralize 10 to 32 units of water into their crystalline structure. Hydration products such as ettringite are traditionally avoided in construction applications due to their propensity for volumetric expansion after cement setting, leading to micro-fissures and subsequent strength degradation (known as ‘sulfate attack’). This paper proposes that such hydration products benefit the strength development in paste backfill slurries with the aforementioned characteristics due to their greater potential to mineralize free water. The newly developed calcium aluminosilicate binder is designed to replace 50-100% GGBFS or other SCMs used in paste backfill systems and meet operational strength requirements by providing exceptional hydration characteristics through cementitious reactions. Additionally, the aluminosilicates used have a minimal carbon footprint and a secure supply outlook, thereby allowing mine operators access to a low-carbon binder option throughout the mine’s lifespan.

May 4, 2025

By R. B. Moore

The story of helium is one of the romances of science . Probably nothing , except perhaps radium , compares with it in human interest . Helium is one of the best examples of a discovery in pure science that has wide commercial application . In 1868 , an eclipse of the sun was visible in India , several scientific men who were in India making observations of the eclipse turned a spectroscope for the first time on the solar chromosphere - that part of the atmosphere of the sun , about 10,000 miles deep , which merges into the corona . A bright yellow line was observed and was thought at first to be due to sodium . Janssen showed , however , that this line was not just the same as either the D or D₂ line of sodium, although it was extremely close to these lines , hence he suggested that the new line have the designation D₂ . Frankland and Lockyer decided that Dz was due to an element in the sun not previously discovered on the earth , and suggested for it the name "Helium" from the Greek work " Helios " the sun . For several years nothing more was done in connection with this element . In 1894 , Sir William Ransay , in conjunction with Lord Rayleigh , made his memorable discovery of argon in the atmosphere , which was announced at the British Association meeting in the same year . After this discovery , Ramsay looked for other sources of the element . Through Sir Henry Miers , he learned that Dr. W. F. Hillebrand , of the United States Geological Survey , had obtained an inert gas from certain uranium minerals , which gas he had decided was nitrogen . Ramsay believed that part of it might be argon ; he obtained from Hillebrand for experimentation , a sample of the mineral , cleveite , one of the uranium minerals , and after extracting gas from the mineral and purifying it , he ran it into a spectrum tube . The lines obtained ' were , however , different from those of argon; among them was the bright yellow line noted by Janssen . Thus was terrestrial heliun discovered .

Jun 1, 1922

By K. Saberyan

A technique is described for the solvent extraction of zirconium. In this method, zirconium has been extracted quantitatively from 0.005 M sodium salicylate solution at pH 2.5 - 3 using 0.01 M triphenylphosphine oxide dissolved in toluene as an extractant. Zirconium has also been recovered quantitatively from 0.2 M potassium thiocyanate solution, but extractions in nitric and hydrochloric acids (as media) were negligible. The resulting extracted metal ion has been stripped with sulfuric acid (0.5 M) and determined with inductively coupled plasma atomic emission spectrometry. This method has been applied successfully to achieve 95% recovery of zirconium from zircon concentrate.

Jan 1, 2010