Search Documents

By J Mauk, J Rowland

The Karangahake epithermal Au-Ag mine consists of two main lodes, the Maria and the Welcome/Crown hosted in Miocene andesites. Mineralisation is strongly constrained to major structures and is genetically linked to dynamic tectonic processes. Two main periods of faulting are represented in the deposit: 1. NE striking right-lateral/normal oblique linked spatially and temporally with the mineralising system, and 2. ESE striking right-lateral/normal oblique post-mineral faulting that displaces the lodes. Paleostress analyses performed on a limited kinematic data set indicate NW-SE extension during the formation of the vein system. Veins and lodes strike NNNE and accordingly contain a strike-slip component. The kinematics of vein formation at Karangahake is broadly consistent with that of other deposits within a NNE-trending belt of deposits. Oblique shear on deflecting structures will create zones of compression and dilation. Dilatant zones created on steep structures create fluid pathways potentially focussing large volumes of fluid from deep parts of the system into dynamic structures.

Jan 1, 2003

By Roger P. Ashley

The main problem in geochemical exploration for gold ore bodies in the 40 km2 hydrothermally altered area at Goldfield is to decide which of the many silicified ledges exposed are most likely to yield deposits with additional subsurface exploration. We conclude that the most efficient way to search for exploration targets is to collect rock samples from the ledges and analyze for the following elements in decreasing order of priority: gold, lead and silver, bismuth, and mercury. These elements form relict hypogene aureoles restricted to the ledges and are not appreciably redistributed during supergene leaching.

Jan 1, 1978

By J. M. Hong, H. K. Zheng, R. Hu, C. B. Zhou

The Jinping-I double curvature arch dam, located in the middle reach of the Yalong River and with a maximum height of 305 m, is the world highest dam of the same type that has been completed. Since the second and third periods of the reservoir impounding, after which the reservoir water level was raised by about 200 m, a significant amount of leakage was observed out of the drainage holes deployed in the lowest drainage tunnel at the left-bank abutment at EL. 1595 m, with a pressure of 0.3 MPa at one typical hole when it was blocked. In this study, a number of analyses including water quality analysis, digital borehole imaging, tunnel geological mapping and in-situ groundwater monitoring were performed to investigate the source of leaking, the leakage passages and the performance of the grouting curtains. An inverse modeling procedure combining the orthogonal design, finite element forward modeling of the transient seepage flow, artificial neural network and genetic algorithm was invoked to further evaluate the permeability of the foundation rocks whose permeability was underestimated in design, using the in-situ measurements of flow rate and piezometric head. The geological structures that lead to the leakage were identified and the seepage flow behaviors in the dam foundation and the left bank abutment were assessed. Given the connectivity nature of the sub-vertically oriented fractures that induce the leakage event, it is found that some of the drainage holes with relative larger amount of discharge could be closed or blocked for reducing the amount of leakage without remarkably increasing the pore water pressure in the foundation rocks.

Jan 1, 2015

By B. Boryczko, J. Norwisz, Jose Escobedo Bocardo, Z. Kolenda, A. Holda

"Classical thermodynamic analysis of any thermal and chemical process is usually based on the first law of thermodynamics. Such an approach is not sufficient when deeper understanding of the nature of each elementary process is required. The use of the first and second law of thermodynamics together is necessary to solve practical process more effectively. Enthalpy and exergy balances allow to enhance our understanding of thermal processes especially when cumulative consumption of energy and exergy is calculated. To ensure reliability of such an analysis the least squares method for adjustment of mass balances of principal chemical elements has been applied and described in detail. Numerical analysis has been carried out to compare two different processes of copper production – shaft furnace and flash smelting.IntroductionClassical thermodynamic analysis of any technological process is usually based on the First Law of Thermodynamics in the form of energy (enthalpy) balances. Such an approach is useful in engineering practice as it makes analysis easier in the global scale neglecting modeling of the elementary processes, allows calculation of the thermal efficiency and makes possible to control quality of the measurement results. Additionally, graphical presentation of the energy balance is simple in the form of Sankey diagram.In the case of aluminum electrolysis process, design of the new electrolyzer or its modernization is always based on the enthalpy balance.However, deeper thermodynamic analysis leads to the conclusion that such an approach is not sufficient. The First Law of Thermodynamics guarantees the exact equivalence of the various forms of energy (allowing all forms to be measured in the common unit such as joules) but it does not guarantee interconversibility. Thermal energy (heat) is in a peculiar and unique position, for whereas all other forms can be completely converted into thermal energy, the reverse process id impossible, only a portion of the heat can be converted into mechanical energy. Explanation comes from application of exergy balances. As we know exergy expresses the amount of mechanical work necessary to produce a material in its specified state from components common in the natural environment, in a reversible way, heat being exchanged only with environment [1]. Consumption of exergy connected with the fabrication of some considered product appears not only in the plant manufacturing the product, but also in all plants delivering raw materials for the final production process"

Jan 1, 2008

By W. R. Matizamhuka

"The consolidation of nano-sized composite materials presents a challenge using conventional hot pressing methods. Spark plasma sintering (SPS) technology has shown great promise in the successful sintering of nanoreinforced composite materials. This qualitative review seeks to impart knowledge gathered, and progress made over the years on the consolidation of nanocomposite materials using SPS technology. The review is aimed at introducing this technology to the South African science and engineering community. Emphasis is on improving the mechanical properties of structural ceramic nanocomposite materials, which over the years have shown great promise in a wide range of applications, including transport, energy, mining, and the environment. Although success has been achieved within the laboratory for research purposes, there are still great opportunities to commercialize the technology for the production of larger components with more complex shapes.IntroductionSince the pioneering work of Niihara and Nakahira (1991) over a decade ago there have been extensive attempts to harness the potential of nanostructural metals, ceramics, and composites in a number of applications (Niihara and Nakahira, 1991; Selaho et al., 1997; Sekino and Niihara, 1995; Khalil, 2012; Aalund, 2008). It is generally realized that reducing the grain size of materials to nanoscale offers a significant improvement in properties. Attempts to synthesize nanostructured compacts by conventional sintering methods have not succeeded owing to the uncontrollable high rates of grain growth driven by long dwelling times at the sintering temperatures and large powder surface areas (Sergueeva et al., 2009; Gua, Khora, and Chieng, 2004; Tang et al., 2009). Following the development of spark plasma sintering (SPS) technology, it is now possible to process nanocrystalline materials with controlled grain growth. SPS, also referred to as the field-assisted sintering technique (FAST) or pulsed electric current sintering (PECS), was developed with the aim of improving on the well-established hot pressing (HP) technology (Kessel and Hennicke, 2007;"

Jan 1, 2016

By Harry R. Nicholls

As part of the pre- and post - shot mine examination at Project GNOME , acceleration data were recorded underground from a series of chemical explosive shots . The cube root of the charge weight was used to scale acceleration and distance because charge weight was not constant . Regression analysis of particle acceleration - distance data gave the following propagation equation : A W1 /3 = 5.10 x 105 ( R / W¹ / 3 ) −2 .43 The quantity A W1 /3 is scaled particle acceleration expressed in g's - lbs¹ / 3 , and R/W1 /3 is scaled distance expressed in ft / lbs¹ /3 Data obtained from the nuclear explosion were scaled and fall within one standard deviation of the calculated propagation law for the smaller shots . Cube root scaling laws were adequate to group acceleration data from explosive charges varying by a factor of more than 1 x 10 in charge weight and over shot - to - gage distances varying from 100 to 46,000 feet . Data obtained from a series of small tests provided sufficient data from which reliable predictions of acceleration could be made for the large nuclear explosion .

Jan 1, 1964

The data about production in this county are exceedingly meager, and there are few reliable data about shipments. It is probable that consid¬erable amounts of coal from here moved north to Erie by both the Beaver and Erie. Canal and the Erie and Pittsburgh Railroad, and if so, they are included with Mercer County. The data in the early state reports are very inaccurate and are always much too low. Much of this coal was used in local furnaces and iron plants and not handled by railroads. There was some production in this county on the line of the Pittsburgh, Fort Wayne and Chicago Railroad, of which no record can be found. The estimated production is based on the number of mines reported as operating in the county at various dates and their probable output, as suggested occasionally in county histories. It is believed that these figures are below, rather than above, the actual figures, which can now never be obtained.

Jan 1, 1942

"Foreword by Emily SarverAssistant professor, Mining and Minerals Engineering, Virginia Tech, Blacksburg, VAThe Mineral Processing Division hosted its fifth Student Poster Contest during the 2014 SME Annual Meeting and Exhibit in Salt Lake City, UT – and, by all accounts, it was a huge success! This year, the contest more than doubled in numbers of individual entries and schools represented. A total of 30 students participated, including 23 graduates and 7 undergraduates, representing 13 US and international institutions: Colorado School of Mines, Michigan Tech, Missouri University of Science and Technology, Montana Tech, New Mexico Tech, South Dakota School of Mines, University of Kentucky, University of Utah, Virginia Tech, West Virginia University, Autonomous University of Chihuahua (Mexico), UNAL Medellin (Colombia), University of British Columbia (Canada). In addition to constructing their posters, students submitted abstracts and gave short oral presentations highlighting their research. Based on tallied scores from all three components of the contest, the judging panel selected 1st, 2nd and 3rd place winners at the undergraduate and graduate levels, which were announced during the MPD Luncheon on February 26.In the undergraduate division, University of Utah’s Lucas Pich was awarded the 1st place prize for his poster “Solid-liquid mixing studies in lab-scale flotation tank using electrical resistance tomography.” His extended abstract is included in this issue of Minerals & Metallurgical Processing. Joshua Chidester, also of Utah, won 2nd place for his poster presenting “Evaluation of detectors for radiotracer RTD measurement by MCNP.” And Lucas Rojas-Mendoza, of UNAL Medellin, took 3rd place for his poster on “Preg-robbing in Colombian gold ores.”In the graduate division, 1st place went to Caelen Anderson, of the Colorado School of Mines, who also placed in this contest in 2012 and 2013! The 2nd and 3rd place prizes were awarded to Jacob McDonald and Joseph Halt, respectively, both of Michigan Tech. Extended abstracts describing the work of these up-and-coming researchers are also included in this issue.The 2014 Contest was chaired by Emily Sarver (Virginia Tech) and Lisa Schlink (Freeport-McMoran Copper and Gold, Inc.). Aaron Noble (West Virginia University), David Perkins (Derrick Corporation) and Derek Novotny (Eriez) graciously served on the judging panel this year.Special thanks are extended to all sponsors of the 2014 MPD Student Poster Contest, and to all student participants. Please watch for upcoming details on the 2015 Contest. We look forward to seeing you in Denver!"

Jan 1, 2015

By C. F. Wingquist

As part of an ongoing study to determine how the wear of mining tools affects dust generation, the Bureau of Mines has measured bit tempera-ture rise during cutting of abrasive rock. Radial bit wear-flat tem-peratures generated by linear cutting in Berea Sandstone were measured as a function of cutting depth and speed. Depths of cut (DOC) were 1/8, 1/4, and 1/2 in, and cutting speeds were 10, 40, and 80 in/s, respectively. Temperature sensing was accomplished by emplacement of a miniature thermocouple into the center of the wear flat. Temperatures observed ranged from 2000 to 5000 C. Correlation between depth and temperature was weak. Temperature increased linearly with speed at 1/2-in DOC, but data taken at 1/8-and 1/4-in DOC produced inconclusive results. The results indicated that at least for deeper cuts (1/2 in), bit temperature, and therefore wear, can be reduced by lowering the cutting speed.

Jan 1, 1987

By E. Swartzman

"DURING 1951, experimental cleaning studies on both fines and larger sizes of certain Canadian coals were conducted on a relatively large scale in two pilot plants in the United States, large enough to be considered as small commercial units, and in one commercial plant in Canada.One of the pilot plants was a wet washer of a type which apparently has never been .used in Canada, nor has any Canadian coal been tested in it before. In the other pilot plant and in the commercial plant, dry cleaning equipment was used. The commercial plant is the first of its kind to be employed in Canada, and this type is used only to a limited extent in the United States.Fine-Coal Cleaning ExperimentsTest PlantsHydrotator and Hydrotator-Classifier combination pilot-plant with a capacity of about twenty tons per hour. This is a classifier type washer adapted for cleaning fine coal as well as certain intermediate sizes. The Hydrotator deals with that portion of a coal retained on approximately a 24-mesh Tyler sieve, whereas the Hydrotator-Classifier deals with the minus 24-mesh fines."

Jan 1, 1952

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By A. C. Stevenson

"The most common theory is that, since thyristors, diodes, and insulated gate bipolar transistors (IGBTs) are “solid state” they will live forever. This is not so. They have wear-out mechanisms (e.g. insulation) and other mechanical parts such as motor bearings. These wear-out phenomena can be easily calculated. In this paper we will look at some of the failures and the failure rate of thyristors in power converters to see what affects them and to see what improvements can be made. If converter failures do occur, some simple forensic engineering steps will show if this is the root cause of the problem.IntroductionLook at the general failure rate curve for thyristors, diodes, gate turn off devices (GTOs) and IGBTs shown in Figure 1. We see that there is an initial high failure rate due to manufacturing defects, application problems, and drive start-up stresses that lasts for a few weeks. This is followed by a long period of (hopefully) several years with a relatively low but very slowly rising failure rate. At the end of this period, the devices start to wear out and the failure rate suddenly starts to increase rapidly over a few months. This signals the end of life for the devices in the system. We will start by looking at this end of life area."

Jan 1, 2000

By D. Bessinger, J. Rabe, J. Zietsman, C. Coetzee, P. H. Lamont, J. Muller

The UCAR® CHILL-KOTE? freeze lining concept combines wall cooling with carbon and graphite refractories of higher thermal conductivities to ?chill? the refractory lining by transferring heat from the refractory lining. Effective sidewall water cooling, together with the efficiency of the heat dissipating conductive refractories, lowers the temperature of the lining to below that of the molten process materials. This causes a layer of slag and process metal to solidify or ?freeze? and form a protective ?skull? which completely coats the refractory hot face. Once formed, the slag skull insulates the refractories, reducing heat loss and protect the lining from erosion, chemical attack, thermal shock, and other stresses. The result: extended life and greatly improved refractory performance. The Ilmenite smelting process depends on the presence of a solidified slag skull to protect sidewall refractory material from chemical attach by molten slag. No known refractory material is able to withstand this corrosive material. To date, UCAR has not applied their Chill Kote ? technology in the ilmenite smelting industry. This paper revolves around the results obtained from conducting an ilmenite smelting campaign on a 500kW DC open-arc furnace with a UCAR designed refractory system. The purpose of this test was to establish the effects such a lining has on refractory wear and the reduction-smelting process. Proper thermo-couple management enabled the authors to monitor lining wear for the duration of the campaign. Prior to the pilot-scale campaign, modeling work was completed to evaluate the feasibility of applying UCAR® CHILL-KOTE? technology to ilmenite smelting furnaces. The successful operation of a pilot-scale furnace equipped with the UCAR® CHILL-KOTE? lining as well as concise modeling suggest that it should be a viable option to consider for an industrial-scale furnace.

Jan 1, 2007

By W. B. Weston

To mining people who have experienced the tremendous expansion of existing operations and the development of new properties over the last several years we do not have to point out the difficulties in hiring skilled equipment operators. To those of you who have opened operations in some of the more remote places in the world this is not just a difficulty. It is an impossibility. Your only recourse has been to try and train whatever manpower has been available. Depending upon your success in training, the next problem has been to keep them. On todays modern equipment, the skill of the operator remains as the greatest single variable affecting the performance of the machine. On a blast hole drill, for example, a skilled operator will get good production footage, acceptable bit life and minimal machine downtime The unskilled operator will not only fail to get the acceptable production footage but all too frequently this failure is coupled with low bit life, high repair costs and excessive machine downtime. Even between experienced operators, on identical machines, in the same kind of material we find significant variations in performance. It is, therefore, the skill of the operator, not just his experience, which makes the difference. The problem, as presented to us by our customers, has been to find a way for the unskilled man, with minimal training, to match the performance of the most skilled and experienced operator. The obvious answer is automation.

Jan 1, 1970

Case studies from four western states are used to illustrate the impact of the environmental compliance process on the mining industry. The case studies were not chosen as a statistically significant sample of all mining operations in the western United States but were chosen as representative of operations on both public and private lands and in locations that exhibited varying degrees of involvement by governmental units, non-governmental organizations and the general public. Basically, each case study was chosen because some aspect of their environmental compliance process helped to illustrate an interesting point in the regulatory process. The criteria used to select the case studies were: mines located in different jurisdictional areas, mines located in varying geological areas~ mines located in areas having different historical relationships with mining: and operations that are in production as well as those seeking an operating permit. The variety of such projects should provide the necessary foundation to evaluate the impacts of the environmental compliance process in each location.

Jan 1, 1994

By Saurav Kumar, Akshay Kumar, Vinayaka R. Kiragi, M. K. Banerjee, Amar Patnaik, Vinod Kumar

Today’s industrial technology offers to optimize and reutilize the resources available in terms of scum that remains after hot rolling in steel rerolling mills in Rajasthan, India. Vast reserves of low-grade coal exist and tons of mill scale are produced everyday after hot rolling in steel rerolling mills in Rajasthan, India. The present research work aimed to optimize the various parameters of solid-state reduction of mill scale using low-grade coal from Rajasthan, India. This study investigates the effect of reduction temperature (850–950 °C in steps of 50 °C), reduction time (60 to 180 min, in step of 60 min), mill scale size (800– 300 μm), and mill scale to coal ratio (1:1, 1:2 and 1:3) on achievable metallic iron percentage and its metallization. A higher percentage of iron content is obtained at a lower particle size of 300 μm. The structural analysis is carried out on 300 μm mill scales using XRD analysis, which shows the percentage of iron is approximately 63%, and metallization above 80% can be obtained under the reduction temperature at 900 °C for 180 min, for 1:3 ratio (mill scale to coal ratio). The chemical composition of the mill scale is obtained using X-ray fluorescence (XRF), and particle sizes as well as distribution of mill scale are determined by scanning electron microscopy (SEM). The elements present in the mill scale are also verified using EDS, which indicates the presence of a major portion of Fe, followed by Fe2O3, Si, and C, respectively.

Aug 14, 2020

By A Melkumyan, M Balamurali

Geological domains describe the mineralisation state and stratigraphic location of different geological regions of mines. They play a very important role at the geological modelling stage as weight percentage of chemical elements information within each geological domain is assumed to be correlated while information coming from different geological domains is considered uncorrelated. Having correct domain assignments to both the chemical assays and the 3D space of modelling is critical for building a reliable geological model of the mine.As standard practice significant effort is invested into the interpretation of the deposit and identification of the geological domains for the chemical assays and the 3D geological space. Despite these efforts, there are some chemical assays with ambiguous geological domain where the exploration assay domain and the block domain do not match. Incorrectly including a sample in the wrong domain can cause a large change in the predicted weight percentage of chemical elements estimation for that block. Therefore, the major challenge of grouping the spatially correlating weight percentage of chemical elements is how to determine which of these domains best fits these misclassified samples.This work proposes machine learning based autonomous technique for identifying to which geological domain (the exploration assay domain or the block domain) the misclassified sample belongs. The proposed methodology is based on Gaussian Process (GP) classification. The GP machine learning approach consists of training and inference stages. At the training stage the GP automatically learns the properties of different geological domains using the chemical assays with unambiguous domain assignment. Then, at the inference stage the GP makes predictions for the geological domains of the assays with ambiguous initial domain assignment.We tested the proposed technique by conducting a case study for an iron ore deposit located in Western Australia. The results demonstrate that the application of the proposed GP technique removes statistically significant deviations in the assay values in many regions: mineralised ore region, unmineralised region, highly weathered region and intrusive material that is highly variable. In this case study the proposed methodology autonomously identified the geological domains for more than 50 per cent of samples which are initially ambiguously classified. For the majority of the assays the GP predicted domain agrees with the geological domain assigned by the exploration assay.CITATION:Balamurali, M and Melkumyan, A, 2014. Automated identification of geological domains for exploration assays with ambiguous initial domain assignment in an iron ore deposit, in Proceedings Ninth International Mining Geology Conference 2014 , pp 99–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By G. G. Campbell

"HistoricalBARYTES was mined in Nova Scotia as early as 1874 from a deposit at Five Islands, on the north shore of Minas Basin. The first record of the presence of the mineral at the Walton site appears in a report by Selwyn in l893, who states: ""Barytes in considerable quantity occurs in veins in lime-stones at Walton and Pembroke"". The exact site of the present workings was marked •on a map published by Fletcher in 1905.The economic •possibilities of this deposit, however, were not recognized until 1940, at which time we were at war with Germany, who up to that time had supplied 50 per cent of the world's requirements.At that time the Nova Scotia Department of Mines, recognizing the need for certain strategic minerals, induced Canadian Industrial Minerals, Limited, to send prospectors into 'the area to look for manganese. No manganese deposits were found, but a deposit of barytes was directed to their attention, and exploration and development work on the occurrence was proceeded with.IntroductionThe south shore of Minas Basin between the Avon river at Windsor and the Stewiacke river at Maitland has long been known as a potential source of mineral wealth. It had attracted the attention of mineralogists and in the past had produced considerable tonnages of manganese ore and gypsum. Depletion of ore in surface and near surface deposits resulted in a dwindling production, until today only deposits of gypsum are worked."

Jan 1, 1952

By L. Godfrey, Z. Nontso, F. Magweregwede, B. Maphalala, S. Khan

The aim of this paper was to establish if mineral resource scarcity is a driver for South Africa to transition to a circular economy. The project objectives were achieved by investigating economically viable, and critical or strategic minerals remaining in South Africa, as well as resource scarcity, as a driver for South Africa to transition to a circular economy. The study found that some minerals in South Africa, such as iron ore, lead, manganese, gold, and cobalt have less than 50 years of economically viable mining remaining. At least 18 minerals can be classified indicatively as critical or strategic: aggregates, bauxite, chromite, cobalt, copper, gold, graphite, iron, limestone, lithium, manganese, nickel, phosphorous, platinum group metals, rare earth elements, silver, titanium, and vanadium. The classification was based on the minerals’ economic importance, supply risk, and potential use in the development and manufacturing of emerging technologies. The findings suggest that the scarcity of mineral resources is a critical driver for the country to transition to a circular economy. Other identified drivers include socio-economic factors, climate change commitments, and business objectives. All minerals are non-renewable resources and at risk of depletion, therefore sustainable extraction and use are critical. Priority should be directed at investigating circular economy opportunities and substitutes for commodities at risk of being depleted within the next 50 years. There is an opportunity for South Africa to transition from a minerals export-based model to one that promotes local mineral beneficiation and manufacturing of end products.

Mar 5, 2025

By M. M. Masood, G. Y. Raju, T. Verma

The inverse velocity method has proven to be an effective approach for predicting slope failures in surface mines by analysing displacement monitoring data. However, the accuracy of inverse velocity method predictions is significantly affected by instrumental noise and natural environmental variations, which influence the identification of different deformation stages. To enhance predictive accuracy, this study applies and evaluates three filtering techniques to velocity time series data: Exponential smoothing filter, short-term smoothing filter, long-term smoothing filter and also compares it to raw data (no filtering). A refined prediction framework, that is, filtered inverse velocity method analyser, is proposed to improve slope failure forecasting in surface mining operations. The results demonstrate that filter selection plays a crucial role in optimising failure time predictions, offering valuable insights for geotechnical monitoring and early warning systems in surface mines.

Sep 1, 2025