Search Documents

By Seppo] [Kreula

Outokumpu Oy has acquired considerable experience with on-stream X-ray fluorescence analyzers and with computer control of flotation processes over several years. It became evident at the outset of this work that a reliable and accurate on-stream analyzer was more than a collection of different pieces of hardware linked together. Extensive work was done to develop an integral analyzer system, beginning with process samples through the spectrometer to report typewriters, recorders and the control computer. To date, over ten Courier-300 analyzer systems based on this development have been installed world-wide, several of which provide the key information for successful computer control systems. Computer control of flotation processes has been under development at the Pyhäsalmi concentrator since 1968. Two different control strategies have been implemented. The copper flotation is controlled by means of a mathematical model and economic criteria, whereas the "evolutionary operation principle" is applied to the zinc flotation. The computer control system installed at' the Vuonos-mine has been developed according to the same guidelines. In order to consolidate this wide experience, a flotation computer control system, Proscon-100, was developed by Outokumpu Oy, and the first system was installed at Kotalahti in 1972. In addition to the technological experience, enough information has also been gathered to illustrate the economical, benefits accruing through the use of these advanced tools of automation.

Jan 1, 1973

By D. Harrington

The greatly extended use of the underground trolley-locomotive system for hauling coal without doubt was one of the most important factors in the rapid progress of coal mining and the increased production of coal in American coal mines during the period 1910-20. Much of the superior efficiency of production of our underground coal and metal lines should also be credited to the trolley locomotive system. The trend to mechanization of mines during the past 15 years, mere particularly the past 5 years, with higher production per man employed and greatly accelerated advancement of working places, has required increased use of trolley locomotives, necessitating larger equipment, higher speeds, and more 'frequent turn over of pit cars. This is re¬flected in increased size of locomotives and the use of larger mine ears (some with a capacity up to or over 10 tons); moreover, heavier rails and larger-size trolley wires have boon or ought to have boon installed. Trolley-locomotive haulage has proved to be rapid; economical, efficient, and productive; nevertheless; in spite of these advantages, so-many hazardous features and, unsafe conditions are involved and the price paid in life and property is so high as to justify the statement that the system should be scrapped if it cannot be operated under reasonably safe conditions. Since bare trolloy wires were introduced into underground mines, they have boon responsible for the death of hundreds of diners, property damage totaling millions of dollars, an indeterminate loss of tonnage through the abandonment of mines or parts of mines, and loss of time after disasters caused by fires or explosions originated by the trolley haulage system.

Jan 1, 1945

By Evgueni Jak

Recent advances in analytical, experimental techniques, and computer-based theoretical modelling of fundamental properties and elemental processes, provide new opportunities to develop the next level of whole-of-reactor pyrometallurgical furnace models. These models have the potential to significantly improve the prediction of, and adding value to, industrial operations. In non-ferrous smelting, the starting point of these models is the development of multicomponent thermodynamic databases for gas-slag-matte-speiss-metal-solids phases supported by systematic experimental research. The whole-of-reactor-models additionally should take into account kinetic processes taking place at micro- and macro- scales, and other key factors. Examples of applications of the latest research tools and modelling approaches to analysis of industrial flash and top submerged lance (TSL) sulphide smelting processes are presented. Different levels of industrial modelling are discussed from elemental local reactions, through general and more detailed whole-of-reactor-models, to plant sections and further to whole plant operation models. Some principles for development of pyrometallurgical reactor models are discussed.

By Albert E. Long

THIS GLOSSARY is published lay the Bureau of Mines as a contribution too the mining literature to fill a long-felt need for a compilation of the terms used by the diamond-drilling industry. The first step toward preparation of the glossary was taken in October 1955 when the Diamond Core Drill Manufacturers Association (DCDMA) proposed that the Bureau of Mines undertake the cons compilation and publication of a glossary of the terms used by the diamond-drilling industry. The work was authorized in July 1956, and a preliminary draft of the glossary was completed in may 1958. Copies of the draft were submitted for review to members of the DCDMA and appropriate personnel of the Bureau of Mines. The final draft, incorporating the many helpful suggestions of the reviewers representing both the diamond-drilling industry and the Bureau of Mines, was completed in March 1959.

Jan 1, 1960

By J. D. Miller

"It is now possible to use 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles which range in size from 150 mm to 1 mm at a voxel resolution of about 150 microns. This is quite a significant advance in X-ray tomography technology and should be useful for plant-site coarse particle characterization (size, shape, composition, density, texture, grain exposure, mineral liberation) with a response time of minutes after receiving the sample. Applications in the mineral industries are discussed including the coal industry, aggregate industry, metal mining and the processing of industrial minerals. INTRODUCTION Plant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants, and mineral processing plants is needed to improve plant capacity, product quality, and/or process efficiency. Not much on-line coarse particle characterization is done at these plants. Some limited information regarding particle size is obtained on-line from reflected light images using systems such as the OPSA, Split, and WipFrag analyzers. Even laboratory analysis of coarse particles has been difficult because of the large amount of sample required to insure statistical significance of the results. During the past decades laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage [1, 2]. 3D X-ray tomographic analysis had its origin in the medical services industry; it is used to provide internal images of the human body and now has also been developed for non-medical applications [3]. Figure 1 shows a schematic diagram for the cone-beam geometry micro-CT system. In our case X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a three-dimensional image is reconstructed from the collected set of projection images. With the availability of automated high speed X-ray tomography [4] it now seems possible to do plant-site particle characterization at a sampling rate of about 3 kg/min for particles which range in size from 150 mm to 1 mm at a voxel resolution of about 150 microns. This is quite a significant advance in X-ray tomography technology and should be useful for plant-site particle characterization (size, shape, composition, density, texture, grain exposure, mineral liberation) with a response time of minutes after receiving the sample. Applications in the mineral industries are discussed including the coal industry, aggregate industry, metal mining, and the processing of industrial minerals"

Jan 1, 2016

By A. B. Hooker, P. G. Guest, E. J. Gleim

"From time to time the United States Bureau of Mines has received reports of gas explosions alleged to have been caused by correctly assembled flame safety lamps. In most of the mines where the explosions occurred the lamp was in use at a working face where the velocity of the ventilating current would be relatively low. The inference has been that the lamp was correctly assembled but that the gauze became sufficiently overheated to ignite the surrounding atmosphere.As part of its routine investigation of flame safety lamps the Bureau of Mines subjects each lamp to a test in still and moving atmospheres to determine its safety. Heretofore, as long as the lam, successfully passed this and other tests no determinations as to the margin between success and failure were made; hence, in attempting to answer inquiries concerning the reported explosions it was found desirable to be able to give actual gauze temperatures as a measure of the comparative safety of lamps under various conditions. The previous laboratory tests of flame lamps in still mixtures were made in a chamber or ""gallery"" of relatively small volume where the lamps might have been subject more or less to the smothering effect of the combustion products. It was therefore decided to make a special series of tests to obtain the gauze temperatures of both bonneted and unbonneted lamps in still and low velocity mixtures, using a larger gallery to offset any smothering effect.These tests are believed to represent the first attempt at measuring gauze temperatures by means of themocouples. The results will not only be of interest but will also be helpful to many in determining the status of flame safety lamps relative to gas ignitions in mines."

Feb 1, 1929

By J. Boisvert, E. Daniels, C. Deutsch

"INTRODUCTION Conventional mine planning is performed on a single resource model at a selective mining unit (SMU) scale deemed appropriate for the deposit and mining method. Estimation methods such as kriging and inverse distance, commonly used to construct a single model, are susceptible to histogram smoothing (Rossi & Deutsch, 2014). This can be mitigated by limiting the number of composites per estimate, therefore correctly reproducing the distribution of estimates (Boisvert & Deutsch, 2012). Search limiting techniques remedy histogram smoothing at the cost of introducing a problematic conditional bias (Isaaks, 1999) and introduces even greater spatial smoothing. Localization is an alternative, offering histogram reproduction through post processing of more robust probabilistic modeling techniques. A single localized model at the SMU scale is desirable. The correct histogram can be reproduced and a single model allows for the use of conventional mine planning and resource evaluation techniques. Despite the advertized benefits of localization, the necessary reliance on a larger panel scale as a middle step in the localization process yields unsightly “edge-effect” artifacts (Boisvert & Deutsch, 2012). Two approaches to artifact reduction are presented here. The first is a straight forward optimization approach designed to minimize an objective function that penalizes artifacts including panel edge discontinuities to generate a model free of panel edge-effects. The second approach redefines a panel in a less conventional fashion as a randomly chosen set of SMUs throughout the domain. This method produces a model void of any regular panel shape resulting in an artifact free model. Artifact reduction minimizes the obvious “edge-effect” issues of localization but local precision issues described by Boisvert & Deutsch (2012) persist. Localization is not a replacement for quantified uncertainty for comprehensive risk analysis and resource evaluation. LOCALIZATION Initially developed with Uniform Conditioning in mind, localization collapses a distribution of local uncertainty at a panel scale to an SMU scale model for mine planning (Abzalov, 2006). This process has been extended to Indicator Kriging (Hardke, 2011), Sequential Gaussian Simulation (Boisvert & Deutsch, 2012) and MultiGaussian Kriging (Daniels and Deutsch, 2014). The localization process is performed in a similar fashion regardless of which technique is chosen to create the prior model of uncertainty. Methodology There are three scales of importance considered in the localization process. The point scale, otherwise known as the data scale, is the smallest and is the scale at which experimental data is collected. The SMU or block scale is the familiar scale at which mine planning and resource evaluation takes place. Lastly, the panel scale is larger and contains a number of SMUs. Each of the three scales is illustrated in Figure 1."

Jan 1, 2015

By Luca Tommasi

Danieli complemented its wide range of production plants for the iron and steel industry with a further step upstream into iron ore pelletizing and beneficiation. Danieli has engineered and constructed a state of the art and fully automated pilot plant facility – pot grate and sinter box – at Altos Hornos de Mexico S.A. (AHMSA) Pelletizing Plant, Monclova, Mexico. Installation and commissioning were completed in October 2009. Key features of the pot grate include the avoidance of the need for operator intervention during the test, automatic system preheat, absence of dead time, heat recuperation system with an air/air heat exchanger, oxygen control in preheating and firing with zirconia oxygen analyzer, possibility to test deep beds up to 625 mm. A series of projects have been accomplished by AHMSA availing of the pot grate facility with the aim to enhance pellet plant productivity and to reduce operating costs. The results obtained by use of Danieli pot grate combined with the experience and skill of plant operators has shown significant technical and economical benefits thus fully justifying the initial investment made by AHMSA and confirming the importance of having an in-house testing facility in order to optimize industrial plant operations.

Aug 16, 2017

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By David Kress

Mill crushing drive systems are essential to cement producers. With the increased emphasis on operating efficiency, it is vital that these systems be dependable and reliable. No one needs the costs or headaches associated with unscheduled downtime or inefficient machinery operation. A reliable drive system starts with the proper selection of the ring, or girth, gear and continues through proper maintenance. Ideally, selecting the right girth gear brings together the gear manufacturer, the system designer and the end user. The gear manufacturer must know the details of the application, the demands that will be placed on the gear and the nature of the equipment to be driven. Similarly, the user and the system designer must be familiar with the variables that affect gear drive performance and service. For example, an application that places a torque load on the drive in excess of its rated capacity will result in gear tooth distress and, in severe cases, breakage.

Jan 1, 2000

By P. Moreno

ABSTRACT: The Maras salt terraces, located between Cuzco and Urubamba in the Andes (southern Peru), are living examples of traditional Incan salt production, where present-day artisanal miners produce salt from shallow pans by solar evaporation. In these terraces, natural spring water, eight to nine times saltier than seawater, is used to produce the salt. The field observations and chemical analyses show that the poorly crystalline traditional salt is finer in particle size and contains impurities such as dolomite and gypsum. These differences are the result of shallow pond depth, contamination from wall erosion, and the nonsequential mode of salt crystallization.

Jan 1, 2011

By D. H. Rubisov

The neural networks modelling approach is one of the most elegant black-box type methods to model industrial processes. In this paper, this approach is applied to model the performance of the CEZ zinc electrowinning plant. The model that was built was found to exhibit an excellent predictive ability for voltage and current density. The model was also used to investigate the sensitivity of the process to various key variables such as temperature, current density, zinc and sulphuric acid concentration, etc. Optimal regimes for zinc production were identified from the power consumption standpoint.

Jan 1, 1996

By C W. Davis

Every diesel engine emits approximately 100 million nano diesel particles (nDP) per cubic centimetre of raw exhaust. Each nDP has a diameter of between 50 and 70 nano metres or 1/100th the size of red blood cells (diameter of between 6 and 8 microns). When inhaled, some nDP pass through the lungs and penetrate all body tissue [1]. Europe and North America have recognised and are addressing the long term health problems posed by nano diesel particulate matter (nDPM) across their societies [2.3]. Australia has been slow to recognise the issue, at both a societal and mining industry level. There are chronic health effects for every underground miner and serious legal issues for mining companies with increasingly stringent Occupational Health and Safety legislation being implemented at a state level across Australia. This paper will review progress within Australian society and more particularly the underground hard rock mining industry, particularly in Western Australia (WA).

Mar 15, 2021

By P. J. Adams

Environmental regulations require means for controlling emissions of SO2 NOx and particulate when burning coal. The combustion of coal in limestone fluidized beds is one of the most promising techniques for the necessary reduction in emissions. Fluidized-bed firing, furthermore, offers potential economies in capital equipment. The world's largest steam generator applying fluidized-bed techniques was built under the sponsorship of ERDA and installed in Rivesville, West Virginia. This paper describes the design and discusses the start-up and development difficulties which were experienced during the period from initial operation to current readiness for commercial operation. Other developments leading to utility and industrial fluidized-bed steam generating equipment are reviewed. The future potential of this promising technique is discussed.

Jan 1, 1979

By L. O. Bacon

This Bureau of Mines report summarizes the results of laboratory work in the design of instrumentation for obtaining the dynamic tensile strength of rock at minimum loading. Minimum loading is defined as the lowest tensile loading by pulse reflection to cause fracturing. The instrumentation for obtaining dynamic tensile strengths of rock cores evolved into the use of a compressed-air pellet gun to impact one end of a rock core, suspended by wires, at increasing increments of air pressure. Maximum strain was measured on most or all of the impacts, and the strain at fracture of the core was obtained by extrapolating the pellet velocity-strain curve to the pellet velocity at fracture. Stress at tensile fracture was obtained from the maximum s train, and the dynamic Young's modulus was calculated from the rod velocity by using simple rod theory.

Jan 1, 1962

By W. C. Joughin

The science of soil mechanics is 100 years old, and rock mechanics is about 80 years old. While methods of analysis and design have been developed and have evolved over time, these are relatively young sciences. The rapid increases in computing power and new technologies have enabled more sophisticated modelling and monitoring. However, there are still many aspects of soil and rock mechanics that are not well understood. Geotechnical failures, which have major consequences, still occur. These consequences may include environmental damage, major production holdups and associated loss of revenue, damage to infrastructure, and loss of life. High-consequence events, which are rare, are more difficult to anticipate and to design for, because by their nature they involve extraordinary circumstances or conditions, often geological in nature. The risks are usually mitigated by conservative designs and monitoring. Detailed geotechnical investigations help us to understand the natural variability of soil and rock masses and identify unusual or unexpected conditions. Investigating and researching major geotechnical failures is essential to enable these unusual circumstances to be anticipated. In the past, severe unanticipated events may have been treated as natural events or ‘acts of God’. However, society now has much greater expectations and it is essential to have policies and procedures in place that enable appropriate management of these rare, high-consequence risks. A good example is the Global Industry Standard on Tailings Management (GISTM), which was introduced after the catastrophic dam collapse at Vale’s Corrego de Feijao mine in Brumadinho, Brazil. The address will explain the concepts of uncertainty and variability, and how they should be taken into account in geotechnical design. The challenges facing geotechnical engineers, mine owners, and managers will be discussed. referencing a number of real case studies.

Sep 6, 2023

By D. E. Shanks

As part of its goal to help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is investigating a fused-salt electrolytic procedure for producing zinc metal. A previous report described preliminary, small-scale work on the fused-salt electrolysis of ZnC12. The present report covers a more detailed investigation of the properties of ZnC12-alkali metal chloride electrolyte systems in relation to the production of zinc metal and also discusses electrolysis in largescale, internally heated cells. The effect of composition on bath stability, current efficiency, cell voltage, and liquidus temperature was determined for the ZnCla-NaC1-KC1, ZnC12-NaC1-LiC1, and ZnC12-KC1-LiC1 electrolyte systems. An electrolyte com-posed of 38 mole-pct ZnC12, 31 mole-pct NaC1, and 31 mole-pct KC1 gave the best overall results. Sludge (ZnO) formation in the ZnC12-NaC1-KC1, ZnC12-KC1-LiC1, and ZnC12-KC1 systems was investigated during prolonged electrolysis. The ZnC12-KC1-NaC1 electrolyte showed the least sludge formation. A 1,500-amp cell was operated using the ZnC12-NaC1-KC1 electrolyte at 500° C. Zinc metal was produced at the rate of 4.0 lb/hr with a current efficiency of 95 pct.

Jan 1, 1979

By I. H. Warren, Forward F. A

The reduction of aqueous slurries of uranyl carbonate at elevated temperature with compressed hydrogen m the presence of metal catalysts and certain organic promoters has been shown. to yield uranium dioxide. The reduction takes place in a sequence of steps. The purity and sintering properties of the dioxide make it of interest as a starting material for fuel element production. Simple control can be exercised over the surface area and oxygen/uranium ratio of the product during reduction. URANIUM dioxide for fueling atomic power reactors 1s conventionally produced as a powder by simultaneously decomposing and reducing ammonium diuranate with hydrogen in a furnace at high temperature. Fuel elements are then generally made from this powder by compacting and sintering ( 1). In order that elements approaching theoretical density may be obtained,

Jan 1, 1961

"An innovative concept is proposed whereby the operating power for haul trucks in certain areas of an underground mine are reduced in order to lower ventilation costs. Airflow that must be provided for diesel-powered equipment in most jurisdictions are regulated based on engine peak power capability and engine emissions, both of which can be lowered by artificially reducing the capacity of the engine through the engine control unit. Advances in asset tracking and ventilation on demand enable this methodology and this study demonstrates that it could represent significant value for mine operators. An examination of haul truck duty cycle indicates that de-rating of engine operating power based on the truck’s location in the mine can enable a step change in ventilation rates, often with no material impact on working conditions. Methods for implementation and estimate of cost savings will be defined.INTRODUCTION Ventilation of underground workings remains a significant operating cost burden for modern mine operators. In particular, ventilation rates for underground diesel mining equipment are often defined by local regulatory bodies and are assumed to present minimal opportunity for optimization or savings, at least until battery propulsion systems can be adopted. Commonly, the quantity of air flow required is defined by the peak rated engine output power of diesel equipment. For example, Ontario Regulation 854 SS 183.1 (3) states that “The flow of air must be at least 0.06 cubic metres per second for each kilowatt of power of the diesel-powered equipment operating in the workplace”. Jurisdictions that define air flow using the prescribed CANMET or MSHA ratings use peak engine emissions to calculate air flow required for dilution ventilation. These approaches are similar in that the maximum power capability of a vehicle’s engine is used to define the ventilation rate in all areas where it travels, regardless of what power output is actually used in any of those areas. Examination of the duty cycle of a typical underground haul truck identifies a large variance in the power output of the vehicle depending on its location in the mine and the activities undertaken at these locations. For example, travel on a mining sub-level requires a fraction of the truck’s peak power due to the minimal grade and significantly reduced travel speed. So if we can reliably reduce the peak engine power capacity and engine emissions in areas where peak power is not required, we can logically cut the ventilation rates for those areas."

Jan 1, 2017

Many mining companies aim to integrate sustainability principles into their new projects. There is an intention for improvement, but frequently this results in little more than 'business as usual' projects that retrospectively categorise controls for environmental and social risks as sustainability initiatives as part of a public relations exercise. The successful implementation of sustainability requires a change of mind-set and behaviours at an organisational and personal level. In addition, sustainability incorporates a very wide range of interests and technical disciplines. One of the key challenges is in understanding how and when to pull these diverse threads together within a project or organisational process. This paper will explore a number of themes: What does it mean to implement a project in accordance with sustainability principles? How far beyond 'business as usual' is it reasonable to go, and what is the business case for this? Why do the intentions for sustainability sometimes fail and how can we prevent this happening in future? People are instrumental in delivering sustainability; how do we embed sustainability thinking into their behaviours and decision-making? The approaches that have been taken to integrating sustainability in design; what has and has not worked and some of the barriers to integrating sustainability into design? The authors will discuss these themes drawing on case studies from URS' experience in integrating sustainability into large projects. The authors will discuss the need for: a strategic approach which provides a simple framework for tactical decision-making and the consequences of taking tactical decisions in the absence of this framework, alignment of the project team and promotion of a culture of innovation, a shift from a risk/compliance mentality to an opportunity identification mindset, and a systematic approach to integrating sustainability into project design processes.

Jun 1, 2010