Search Documents

By N Dube, K L. Sandvik, C Mutevhe

Trojan Nickel Mine is the largest producer of Ni, Cu and Co in Zimbabwe. The mine has operated a nickel flotation concentrator and base metal refinery continuously since 1969, creating 28 million tonnes of sulfide bearing tailings, five million tonnes of permanent waste rock and about seven million tonnes of smelter slag. Exposure of the sulfide bearing minerals renders them susceptible to oxidation in the presence of water and oxygen, resulting in acidic solutions with elevated concentrations of total dissolved solids, sulfate, metals and residual flotation chemicals in various waters draining from the mine site. These pollutants pose a direct threat to the environment and human health, and understanding their deportment and behaviour in the various waste streams is essential in the mineÆs environmental objectives to prevent or minimise adverse impacts arising from its operations. A geochemical assessment of the pollutants was carried out to compute a mass balance between the major sources of pollution and the distribution and fate of pollutants in waste streams from the mine site. Waste rock, tailings, surface water, ground water and sediments were sampled, tested and analysed. Mineral composition and water chemistry data show that geochemical reactions are responsible for the release of pollutants from waste rock, tailings and plant spills. Drainage from the mine area is near neutral due to buffering by magnesium carbonates in the fine fraction of the tailings. The natural wetlands that exist downstream of the waste rock and tailings dams are effective in reducing metal loadings to water courses. However, solutes and heavy metals are occasionally released to surface and ground water, when their concentrations peak during the dry season. The results demonstrate the necessity to understand the natural chemical processes that characterise the distribution of pollutants in nature and how such knowledge can be used to develop cost effective methods to remediate pollution in the natural environment.

Jan 1, 2006

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

By A. J. Monhemius

This paper reviews the history of modern iron-control processes in hydrometallurgy. Attention is paid to processes developed in the electrolytic zinc industry for removal of iron from zinc sulfate leach liquors and the problems faced by the industry in the safe disposal of the iron residues produced by these processes. Past lessons learned are projected onto current efforts to develop hydrometallurgical processes for treatment of copper sulfide concentrates. It is argued that any attempt to create a \u201chydrometallurgical copper smelter\u201d will fail, unless methods are developed that can recover iron in a form that can be directly used by the steel or pigment industries.

Jan 1, 2017

By J. P. Barkley

"The accompanying tabulation gives the results of a series of operating tests on two types of small stokers. One was an inclined, natural-draft, moving-grate, overfeed ""hand-stoker"" fired and manipulated by hand; the other was. a horizontal, forced-draft, stationary-grate, underfeed, mechanical unit-stoker operated by an electric motor. These were installed as shown by the accompanying sketches (figs. 1 and 2) under horizontal return tubular boilers of a nominal rating of 150 bl.h.p. each.The steam load carried by these boilers was a rather typical heating load. It was fairly constant and of about 30 bl.h.p. throughout the summer months, with small variation between day and night. During the winter months the daily variations were dependent upon the outside temperature. The boilers were banked a considerable part of the night.As noted in the table, two kinds of coal were used. The size of one kind was run-of-mine and the other 11/4 inch nut and clack. These coals from two different mines of the New River district both caked considerably during burning, the nut and slack more than the other. Analyses of the coal were as follows:"

Jun 1, 1929

By Andreas Zielonka

To meet the increasing demands of the quality and long term stability of technical systems also the applied materials have to full fill higher standards. This is of special importance where the function of a whole system depends on the reliability of the used materials for example for connector systems in automotive, computer and other electronic equipment?s. In most cases for connector systems electro deposited top layers are applied. To improve the quality of the applied layers new electro deposited systems are developed. One important field of research are the development of composite materials as dispersion coatings and multilayer systems. Multilayers are systems with a high number of single inter-layers of different metals or alloys with the wide chance of the alloy composition. As gold is one of the most important contact material for high quality connector systems it is used as basis for the development of multilayer systems. For the electrodeposition of multilayers two different methods can be applied, the single and the dual plating process. As in the dual plating process two different electrolytes are used, the single plating process allows the formation of multilayers from one electrolyte. In the presented research results cobalt and nickel are used besides gold for the formation of the multilayers. The properties of the layers can be influenced in a wide range by the change of electrolyte composition and the process parameters as current density, current waveform, temperature, hydro-dynamic conditions at the electrode surface and by the number and thickness of the inter layers of the deposited materials. The paper describes the fundamentals of the electro deposition of multilayer systems. For the investigation of the properties of the multilayers different techniques are applied. One of the most important parameter are the thickness of the total layer and of the applied sublayers. The thickness of the sublayers can be varied between a few nanometers up to micrometers. The wear resistance, the contact resistance and the plug-in forces are measured as these parameters are important for the technical application of such layers. For the description of the structure composition and surface properties the sample where also investigated by scanning electron microscopy (SEM), energy dispersive x-ray-analyses (EDX) and glow discharge optical spectroscopy (GDOS). The paper shows that the deposition of gold based multilayers is possible and that the properties of such systems can be varied in a wide range what opens new fields of applications of such materials.

Oct 1, 2003

By W. Miola, R. V. Ramaoi

"The MSHA prescribed method for the determination of quartz in airborne respirable-dust samples from underground coal mines is the P-7 method, a combination of /ow-temperature, radio-frequency ashing (LTA) and infra7 red analysis (IR). There is no prescribed procedure for quartz analysis in bulk samples of coal and host rock. Dispersive infrared (IR), Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) methods are most commonly used for the analysis of quartz in powders. Several aspects of the experimental procedures, such as the preparation of the analysis sample from bulk samples, ashing techniques, scanning procedures, peak measurement location, calibration techniques, sample amounts, size consist and data interpretation, affect the results from each of the methods differently. Significant differences in analytical results obtained from X-ray diffraction (XRD) and infrared spectroscopy (IR) on the same samples are reported. All studies point to the need for reliable quartz analysis methods.In a recent research program, a procedure for preparing bulk-coal and host-rock samples for quantitative quartz analysis was developed. Further, the results from X-ray diffractometry and infrared spectroscopy for quartz content on identical samples were compared. Calibrations with pure and mixed standards were used to assess the influence of particle-size distribution, matrix and calibration on the analytical results. In this paper, several issues concerning the measurement of quartz in the samples of coal, host-rock and airborne respirable dust from mines are outlined and quantified. IntroductionThe literature on coal-mine airborne-dust control has identified a need for a better understanding of the sources, mechanisms and amounts of quartz in mine airborne respirable dust (Althouse, 1984; Jankowski, Nesbit and Kissel, 1985; Ramani 1988; Qin, 1988; Bhaskar and Xu, 1990; Bhaskar and Li, 1992; Ramani, Qin and Miola, 1991 ). To understand the quartz content in the source materials, bulk samples of coal and host rock must be analyzed. Establishing an analysis procedure for determining the quartz content in bulk-coal and host-rock samples is necessary for identifying the sources of quartz in mines; for establishing the relationships between the quartz contained in the source and in the airborne dust; and for controlling the content of quartz in the mined product and in the airborne respirable dust."

Dec 1, 1996

By A. T. Coumbe

This compilation of statistics covering competitive fuels consumed for heating of residential and commercial buildings is in response to numerous requests for data of this nature to show the relative changes in the demands for the different fuels in recent years. The figures presented cover the amounts of various fuels ant electric energy reported as used for heating dwellings and commercial buildings. However, the totals for gaseous fuels and electricity necessarily include amounts consumed for both cooking and lighting purposes, as these associated household uses could not be readily broken out. [ ] SOURCES OF FUEL AND POWER STATISTICS Liquid fuel: Mineral Market Reports of the Bureau of Mines covering annual Pales of fuel oil and kerosine. The fuel oil figures include grades 1 to h, reported as sold for space heating. Kerosine and grade 1 fuel oil delivered as range oil ore also included. Gaseous fuel: "Gas Facts" published by the Bureau of statistics of the American Gas Association. Thin source was used as It is believed that the data shown are representative of the actual market

Jan 1, 1953

By R. J. Hundhausen

The Takilma-Waldo copper district in Josephine County, Oreg., was studied by the Bureau of Mines from September 1950 to April 1.951 and from December 1953 to April 1954. Funds for the investigation were provided by the Bureau of Mines and the California-Oregon Power Co., Medford, Oreg., on a cooperative basis. The copper mines in the district are credited with a total production of ore worth $1,700,000. Since 1933 the mines have been unproductive and, except for minor exploration, largely inactive. The history of the district indicates that the copper deposits were mined principally during periods of high metal prices.

Jan 1, 1956

By D. B. McGilvra

This paper, describing the mining practices and methods at the Black Rock mine, is one of a series of similar papers on mining methods in the various mines of the United States being prepared by the Bureau of Mines. The Black Rock mine is located in the northeast corner of the Butte district, about 3 miles from the center of the town of Butte, and is owned and operated by the Butte & Superior Mining Co.

Jan 1, 1930

By J. A. Murray

Maintaining satisfactory air quality in electro-winning tankhouses has been problematic and costly, particularly as plant operating current densities have increased. Conventional approaches, including the use of beads, hollow spheres, surfactants and coalescer devices, have not proved completely effective, requiring that powerful ventilation systems be installed. As workplace and environmental regulations become more stringent, containment of the acid mist at its source is more attractive. An electrode cap system based on this approach has been developed and tested in two commercial copper electrowinning tankhouses. The design, development, installation and cost of the new electrode cap system are described.

Jan 1, 1996

By Wilbur A. Haley

The demand on the nation's reserves of high-quality coals suitable for metallurgical purposes is resulting in the rapid depletion of some of the thicker coal beds. These beds are thick enough to permit the use of modern mechanized mining equipment. Many of the thin beds are not being mined at present. In limited areas where the coal is less than 36 inches thick some beds are mined by various conveyor methods. Usually, the room-and-pillar system or some modification of it is used, and often no attempt is made to extract pillars. Consequently, an appreciable quantity of a valuable resource is lost. Many steel companies and coal operators consider reserves of low-and medium-volatile coking coals to be critical, especially in areas where the thin beds are not being mined by modern mining methods. To improve recovery and to promote more-extensive mining in thin beds, methods and devices that are new to American coal mining but applicable to the mining of thin coal beds should be tried. As one of the functions of the Bituminous Coal Mining Section of the Bureau of Mines is to promote improved mining practices and efficiency in the interest of conservation, research in that line is necessary. In 1945 coal planers were observed in operation in Germany by a Bureau engineer member of Solid Fuels Mission to Germany. Planer designs and history of early developments and operations were published. In 1949 an improved planer was again studied by Bureau engineers, and its adaptability to certain conditions in the United States, especially thin beds of friable coal, was considered practicable. After the war the planer was improved, in design and for several years has been operating successfully in the Ruhr. Because of the conviction that the device would be successful, both from the standpoint of conservation and operational prodl1ctivity, under certain conditions in the United States, the Bureau of Mines, through the Bituminous Coal Mining Section, entered into a cooperative agreement with the Coal Division of Eastern Gas & Fuel Associates and Mining Progress, Inc. The purpose of the agreement was to conduct an experiment in modified longwall mining, using a new-type German-built coal plow or planer, known as the Loebbe Habel, supplied by Mining Progress, Inc. The experiment was made to determine if this type of mining equipment operated on a longwall face could be adapted to some of the thinner American coal beds. Such an experiment also would afford many opportunities to study the possibilities and principles of this type of equipment as well as the many factors involved in the mechanical mining of a longwall face.

Jan 1, 1952

By John Murray, Daniel Ebin, Robert Gould

The Atlanta Plane Train project at Hartsfield-Jackson Atlanta International Airport employed the progressive design-build approach. This provided opportunities for collaboration between the design-builder, design engineer, and owner and the implementation of innovative design and construction approaches. The innovations have reduced risks, allowed for adjustments during design to accommodate new challenges, and provided open-book cost and schedule evaluations. The progressive design-build approach has also allowed for pricing of work to occur in phases—capturing the design/construction challenges as the project evolves and when they are more clearly defined. While this has allowed for pricing to be performed with better project understanding and therefore less contingency, the associated time frame for approvals has required careful consideration to avoid impacts to the schedule. This paper discusses the benefits and challenges of the progressive design-build approach.

Dec 1, 2022

By Zhijing Zhang

Sodium borosilicate is the basic composition of coating materials, Vycor and Pyrex glasses. In the present study, viscosities of Na2O-Si02-B2O3 ternary melts were measured under various compositions and temperatures. Experiments were carried out using rotary viscometer and graphite components. Our experimental results were compared with those in literature. Based on present experimental results, the previous structure based viscosity model was modified. The predicted viscosity results are in excellent agreement with the present experimental data in the temperature range with molten state samples. The fitting ranges of the model cover the composition of XB2O3 from 0.1 to 0.6 combined with xSio2 / xNa2O = 0.5, 1,2 and 5 respectively.

Jan 1, 1998

By R. B. Anderson, N. J. Sherren

The mining equipment at the Scully Mine, Wabush, consists of approximately twenty-five large haulage units, eight large dozer-loader applications and seventy other related pieces of service and maintenance equipment. This equipment is operating in sub-Arctic conditions. This pa-per presents a description of the tire maintenance procedures in use here and discusses the tire troubles that are being encountered and the methods of dealing with them.

Jan 1, 1969

By J. S. Marsh

AN incomplete statistical analysis performed wearily on the morning after Thursday, Feb. 12, indicates that the unavoidable items of conversation among steelmen were the current shortage of sleeping time and the "Normandie." No analysis is needed, however, to be certain that many thousands of valuable words were uttered, both in and out of technical sessions, concerning matters of deep interest to members of the Iron and Steel Division. The opening session consisted mostly of papers that have appeared, or will appear shortly, in Metals Technology. One, however, that was not finished in time to be printed in any form, but that aroused great interest, was by E. L. Ramsey and L. G. Graper (Wisconsin Steel Works). Its subject was the production of high-sulphur steel by treatment with sulphur dioxide derived from anhydrous sodium sulphite or bisulphite added to the ladle or to the mold. The sulphide distribution in the finished steel is such that increased machinability and longer tool life result. Both items are of obvious importance in these days of mighty production.

Jan 1, 1942

Agenda ?Trends in Wireless Technology ?Success and Opportunities ?Improving plants efficiency ?Improving plants reliability ?Improving plants safety and security ?Wireless Ecosystem ?Lessons Learnt / Recommendations Why Wireless? ?Lower cost (no wiring cost) ?Flexibility (no wire) ?Standards-compliant wireless devices major factor enabling growth:?Standard WLAN (IEEE 802.11)?Wireless field I/Os (IEEE 802.11, ISA100.11 and WirelessHART) ??Wireless adoption will become a milestone that will rival the introduction of Fieldbus and the distributed control system (DCS) in its importance.? ARC Advisory Group

May 1, 2009

This paper presents the results of an investigation of the stability of the mass flow rates and average pellet size in the different streams of an industrial-scale balling circuit. The variables in this study include water content, drum speed and fresh feed rate. It was found that both the mass flow rates and pellet diameter are greatly disturbed when a change, positive or negative, in any of the variables takes place. For most of these disturbances to be damped don, a period of one hour or so is required. When a disturbance in the feed rate was made, the transient period extended to more than one and half hours (the duration of the experiment). It was observed that there is an interaction between the drum speed and moisture needed for producing an acceptable green ball product. The moisture content of the product pellets was found to be a function of the pellet size, with the larger pellets retaining a higher moisture content.

Jan 1, 1980

Reliable sampling practices are the key to optimising the market value of a mining or chemical companyÆs stock. As a result, reliable sampling standards are needed. However, current standards on sampling present the æuniversalÆ Pierre GyÆs Sampling Theory in an ambiguous way. For example, the Total Sampling Error is divided into its basic components only in informative annexes, when it should clearly be the main body of the standard. Sampling standards are presently loaded with statistical concepts that actually belong in the annexes. Furthermore, many non-probabilistic sampling procedures are still mentioned which do not belong in a standard. The objective is not to criticise existing sampling standards, but to suggest better ones. Sections on the Sampling Theory should divide the Total Sampling Error into a sum of its nine basic components. Then, and only then, should they be addressed one at the time. Sections for establishing a sampling protocol should address the in situ Nugget Effect, the Fundamental Error, the Grouping and Segregation Error, the Long Range Quality Fluctuation Error, and the Periodic Quality Fluctuation Error. Sections for sampling methods, mechanical sampling, manual sampling, grab sampling, sampling of trucks, railroad cars, bags, and drums should be part of the critically important practical implementation of a recommended sampling protocol, called Sampling Correctness. It includes the increment Delimitation Error, the increment Extraction Error, the Weighting Error, and the Preparation Errors. Unless these errors are addressed one at a time, in an unambiguous way, the standard will remain ineffective in solving sampling problems for the industry. Therefore, a strategy is needed to create better standards required at the early stages of new projects, both by manufacturers of sampling equipment and by engineering firms. A logical sequence of important points that cannot be ignored in any sampling standard is presented. An analysis of the practical use of the words sampling uncertainty versus sampling error is recalled. Finally, as a practical example, an in-depth analysis of the correctness of cross-belt samplers is presented, and emphasis is placed on the correct ways to perform bias-tests for mechanical sampling systems.

Jan 1, 2005

By Robert B. McElwaine

"The demand for barite has increased greatly in the last 10 years, especially during World War II. Depletion of oil reserves and subsequent increase in deep drilling created a heavy demand by the oil industry for barite to be used as drilling mud. The great increase in demand for barite gave impetus to the development of a, deposit of impure barite near, Magnet Cove in Hot Spring County, Ark.The critical condition of the national barite supply early in 1944 led the War Production Board to recommend that the Bureau of Mines attempt to prove the existence of a large reserve tonnage of barite in the Magnet Cove area and arch for new deposits. To carry out this program, the Bureau explored on newly reported. Barite deposits in southern Montgomery County, Ark. The Gap Mountain, Fancy Hill, and Sulphur Mountain barite deposits were investigated. Eight diamond core-drill holes and 1,336 linear feet of surface trenching were completed, and barite samples obtained were analyzed, A study of the Montgomery County barnse district indicates that the lenticular bodies of barite replace a favorable host rock near the base of the Stanley shale formation. Barite is exposed along the side of anticlinal mountains where erosion has truncated the beds on the limbs of the associated synclines. An appreciable amount of barite suitable for commercial use has been indicated by trenching and core drilling. The Gap Mountain and Fancy Hill deposits are controlled by the Magnet Cove Barium Corp. and Baroid Sales Division of National Load Co., respectively. The ore is similar to that of the Magnet Cove area and is amenable to concentration by a flotation process. Mining of these deposits had not been begun by the time the Bureau completed its exploration project."

Nov 1, 1946

By Botao Lin, Yan Jin, Hongjuan You, Jingjun Pan, Huiwen Pang, Mian Chen, Sen Chen

"Steam Assisted Gravity Drainage (SAGD) has become the mainstream technology for ultra-heavy oil recovery in Xinjiang oilfield, the success of which depends heavily on shortening of preheating period as well as forming homogeneous and highly permeable zone in land-facies oilsands layer. Towards this aim a special hydraulic fracturing process is required, which is accomplished through controlled water injection to a pair of horizontal wells in order to create homogenously distributed microcracks in the zone between the two wells. The associated mechanical response, however, is unclear for land-facies Karamay oilsands that is loose in texture. In this regard, this research utilizes a triaxial test system on cylindrical specimens extracted from field-collected oilsands cores. Isotropically consolidated drained triaxial compression tests are conducted on both saturated and unsaturated specimens so as to investigate the mechanical response of oilsands at different spots relative to the wellbore. Moreover, acoustic emission and fast pulse-decay permeability are performed to monitor fracture development and permeability evolution. Based on these experimental studies, the mechanism of dilation in oilsands is comprehensively analyzed. The findings reveal distinctive behavior between the saturated and unsaturated specimens as respect to dilation, porosity/volumetric evolution and change of permeability. It is also found that shear bands can be created upon shearing on triaxial specimens, rendering porosity or volumetric strain the factor that is more proper for evaluation of stimulation efficiency in the field.INTRODUCTIONXinjiang oilfield is widely known for its abundant deposit of heavy and ultra-heavy oil that has been estimated to be several hundred million tons. The ultra-heavy oil deposit located in Fengcheng region of Karamay at the northwestern part of the Junggar Basin, Xinjiang, China, has over 360 million tons of resource (Yuan et al. 2013). The resource is deposited in depths from 180 to 450 m and has viscosity over 100, 000 mPa•s at a temperature of 50ºC, bringing technical challenges to recovery activities."

Jan 1, 2015