Search Documents

By Karl A. Higgins

In August 2004, the long-awaited National Harbor project in the DC metro area sprang to life with the design of Gaylord National Resort and Convention Center. When the project was in its final stages of construction in 2007, it was noted as largest building development of the east Coast and the 4th largest Building project in the U.S. The final construction costs were above $900M and it served as the catalyst for the overall National Harbor development which added another $1B in construction costs over the next few years. The Gaylord Hotel is supported by approximately 150,000 linear-feet of driven precast concrete piling, one of a handful of major DC area projects in the early 2000s that were supported by this pile type. The project overall was a success, but the fast-paced construction schedule created significant challenges to the designers and contractors. Piling installation was the first major building construction task, and it did not start out well. While the test piles were installed without damage, when production pile driving began in the summer of 2005, pile head and body breakage soon became evident. Typical of most highprofile projects, there are many stakeholders involved and an equal number of opinions on why the piles were breaking. The financial and contractual implications of starting the project off awkwardly were evident to all. The pile driving criteria was scrutinized by the contractor, and the engineer’s had reservations about the size and type of the hammers used for pile driving. Ultimately, it was proven the leading cause of pile breakage was neither the pile driving criteria nor equipment, rather the pile materials themselves. The author of this paper is also the Geotechnical Engineer of Record for Gaylord National and many of the adjacent National Harbor buildings including the recently completed MGM casino. About 100 piles were damaged during Gaylord’s construction some requiring multiple piles for replacements. Over the past decade or so, rumors on the causes of the pile breakage have spread in the market, with some alleging this pile type is not compatible with the geologic setting. I have purposely avoided writing this case-study due to the controversy surrounding the subject, but now some 15 years later it seems appropriate to do so considering DFI’s annual conference location. This will be a fact-based assessment of pile breakage at Gaylord and will also include a comparison to the neighboring buildings where far fewer driven piles were damaged, once a more appropriate concrete mix design was required. The pre-cast supplier is no longer in business.

By V. C. Rogers

ALTHOUGH surveying at mining properties is fundamentally the same regardless of the method of mining, at Climax, due to the nature of the ground, the policy of advance development work, and extremes in climatic conditions, surveying practice has had to be revised to meet the specialized conditions of this particular type of mining operation. The company's mine is one of the largest underground properties in the United States. It has proved ore reserves of 275,000,000 tons, 60,000,000 tons of which have been broken. To date, 109,000 ft. of development drifting have been driven, as well as 40,926 ft. of development raising, 10,000 ft. of ventilation drifting and raising, 16,000 ft. of exploration drifting, and 206,000 ft. of diamond drilling. Normal production varies between 1.2,000 and 15,000 tons daily. Development work proceeds at a rate of 11/2 tons developed for every ton milled and with a development of 18,000 to 20,000 tons per day, the following crew is required to take care of mine and surface engineering

Jan 1, 1946

By M. J. Kovalik

Lower Sunnyside seam coal from Utah was blended with various proportions of char and high-temperature coke to improve the quality of the coke obtained from carbonizing this coal. The Hanson 5-pound carbonizer was used as a "screening test" for the larger scale Bureau of Mines-American Gas Association (BM-AGA) tests, which were correlated with industrial production. Eighteen carbonization tests were made in the BM-AGA 13-inch retort, with a coal charge of about 90 pounds; the cokes were evaluated by the standard ASTM tumbler test. Carbonization of blends containing char and coke breeze yielded less fissured and blockier cokes of significantly higher ASTM I-inch tumbler indices as compared with the value for the straight Sunnyside coal. It was found that the simultaneous addition of char and coke breeze yielded stronger cokes than that obtained by the addition of either one of these additives. Addition of a small proportion of Pocahontas No. 3 or Sewell coal to an optimum blend improved the resulting coke strength further.

Jan 1, 1969

By John R. Zelonka

Models made by encasing strain-gage networks in epoxy are described and evaluated. With this technique relatively complex models can be constructed in which any number of gages can be located and alined precisely. Although the gages are an integral part of the model matrix, they create no important mechanical or thermal stresses. Model construction techniques and experimental data proved reproducible and reliable. In addition, the sGlution obtained with these models to the problem of the state of stress around a circular hole in a plate subject to a plane stress condition was in agreement with theoretical, photoelastic, and finite-element solutions.

Jan 1, 1970

By W. W. Stephens

As part of the Bureau of Mines program directed toward more effective utilization of the mineral resources of the United States, a number of processes for production of sponge iron have been investigated. The use of sponge iron as a raw material for production of steels and other ferrous alloys offers several possible advantages over the conventional pig-iron and scrap process, especially for utilization of the smeller, widely distributed iron-ore deposits of the western United States. Although considerable information has been made available on various processes for production of sponge iron, little information 118.6 been published heretofore on the problems and costs involved in melting the sponge iron for production of steel. The present Paper reports the results of tests conducted at the Bureau of Nines pilot plant at Redding, Calif. in which several different types of sponge iron Were used as charge material for production of steel in a 4-ton-capacity basic arc furnace.

Jan 1, 1949

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined. Conductivity hard was 98.26 per cent. After a 10-min. heating at 200°C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. Materials and Methods The work was done on high grade electrolytic copper, 99.942 per cent. copper plus silver, silver 0.0008 per cent. It was hot-rolled to >/4 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire 'were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

By John T. Wizzard, R. P. Killmeyer, B. S. Gottfried

The Coal Preparation Branch of the Pittsburgh Energy Technology Center has developed a computer program to calculate the performance characteristics of coal washing devices. This program uses specific gravity analyses of the clean coal and refuse streams as input, and generates dependent and independent performance criteria for the washer. Partition curves are internally represented in a functional form by a Weibull function. Performance criteria generated by this computer program are compared to manually calculated performance criteria for air tables, Dynawhirlpools, Baum jigs, hydrocyclones, and dense medium cyclones. The comparisons show that the computer program gives results in close agreement with the hand- calculated values while greatly reducing the amount of time involved in performing the analyses.

Jan 1, 1983

By M. D. Kaizer

PETROBRAS started its Oil Shale process development in 1953, the PETROSIX process which was developed and tailored to Irati Oil Shale formation. Since 1991, the industrial plant called MI (Industrial Module) has been operating, producing more than 20 million barrels of oil. In order to continue the oil shale exploration, a new shale mine is been opening. This article reports the planed measures taking in order to limit the environmental impacts and to return the land as close as possible to the original condition, as well as with the disposition of the process waste and the city garbage. It shows that the remediation process starts during the mining activities and continues after the mine exploration. Another characteristic of the Petrosix process, the pyrolysis of tires will be focused.

Jan 1, 2014

By Jan C. Still

The Haines-Klukwan-Porcupine subarea of the Juneau Mining District (JMD) is located in the northern portion of the JMD and consists of the land between the Alaska-British Columbia boundary, the Chilkoot Valley, Glacier Bay National Park boundary, and extending south to the Davidson Glacier and the Chilkat Peninsula and Islands (fig A-I). This area was studied as part of the larger JMD study in a cooperative effort between the Alaska Division of Geological and Geophysical Surveys (ADGGS) and the Bureau during 1985 to 1988. Prior to this, during 1984, the ADGGS and the Bureau cooperated in a study of the Porcupine mining area and during 1981 to 1983 conducted separate studies in the area. Field work was conducted by foot, boat, truck, and helicopter. Figure A-I shows the Haines-Klukwan-Porcupine sub-area and shows the areas covered by previous Bureau and ADGGS studies. PHYSIOGRAPHY AND CLIMATE The physiography of the subarea ranges from gentle to rugged. Glaciers formed the major features in the sub-area and left "U" shaped steep walled valleys and rugged mountains. The Chilkat, Chilkoot, Klehini, Tsirku, and Takhin are the major rivers in the subarea. The higher mountains are glacier clad and some valleys still harbor glaciers that reach the valley floors. Lush forests and dense brush predominate up to timberline at about the 2,000-foot elevation. Low point in the subarea is at sea level in the area around Haines while the high point is 7,434 feet at: Mount Henry Clay in the Porcupine mining area.

Jan 1, 2012

By John A. Gann

THE Iron and Steel Division has shared in the general increased activity of the industry. The fall meeting at Chicago was not only well attended but particularly characterized by the virility and scope of the discussions at the various sessions. The program for the February meeting indicates a similar interest in technological developments. The Blast-Furnace Committee continues to have the hearty support of the industry with discussions of such a nature as to be of real help to the operator as well ass the technologist. The work of the Open-Hearth Committee continues to be outstanding, with ever increasing attendance and ever mounting interest in the meetings. Formation of a conference on the physical chemistry of steelmaking has given those interested in this phase of work an organization allowing the same

Jan 1, 1936

By Pertti Koukkari, Nagendra Tripathi, Karri Penttilä, Justin Salmine

ChemSheet is a thermodynamic multi‐phase multi‐component simulation software, which is used as an Add‐in in Microsoft Excel. In ChemSheet, the unique Constrained Gibbs free energy method can be used to include dynamic constraints and reaction rates of kinetically slow reactions, yet retaining full consistency of the multiphase thermodynamic model. With appropriate data, ChemSheet models can be used to simulate reactors and processes in all fields of thermochemistry. The presentation will cover off‐line modeling of Cu‐flash smelters and advanced thermochemical simulation coupled with on‐line process control of Cu‐Ni smelting. The presentation will describe an off‐line model of Cu‐smelter based on critically assessed properties of the Al-Ca-Cu-Fe-O-S-Si –system (slag, matte and liquid metal) by using the quasichemical model. A four‐stage reactor model (shaft, settler, uptake and bath) is used for optimizing process parameters and feed particle distribution. As a second example, an advanced thermochemical model of a Ni-Cu sulphide smelting plant will be given. The on‐line model covers the operation of treating Ni-Cu-S concentrate via roasters, electric furnace and converters, producing a high grade Bessemer matte product for further refining. The model integrates the thermochemistry of the roasters and electric furnace, and predicts important process parameters such as degree of sulphur elimination in the fluid‐bed roasters, matte grade, iron metallization, slag losses and the iron to silica ratio in the electric furnace slag. Both models can be used to assist process engineers and operators in calculating the addition rates of coke, flux and air for different feed scenarios.

Jan 1, 2014

By A. J. Strazisar

The Bureau of Mines conducted a laboratory investigation to study the effectiveness of low-pressure steam and water spray in suppressing respirable dust at the tips of a saw-type cutting wheel. Suppression efficiencies were found to be proportional to the amount of the water or steam applied at the cutter tips. For equivalent water output rates, a maximum efficiency of approximately 80 percent was reached for both steam and water spray. Results from the steam and water spray tests showed an increase in suppression efficiency with an increase in particle size of 1 to 8 micrometers. The data indicate no advantages for using steam as a dust suppressant.

Jan 1, 1972

By Ling Wu

The development of pyrometallurgical technologies has been focused on new smelting reactors, but the proposal for new converting reactors has been substantially lower. Up to today about 80% of copper matte is treated by the traditional P-S converters which have the weakness of pollutant fugitive emissions. Therefore, the continuously converting processes for treating molten matte have been studied and developed. In July 2017 the "oxygen-rich side blowing smelting + multi-lances top converting & fire refining" continuous copper treating process was commissioned. This process was designed by ENFI and YanTai GuoRun Copper Smelter. In this process, oxygen rich side blow technology is adopted for smelting, which is a new type of side blowing smelting furnace to produce high-grade copper matte. The converting adopts the horizontal multi-lances top-blowing continuously converting process, which eliminates the transportation of molten melt and the SO2 fugitive emission. The intermediate products of this process, copper matte and blister copper is fed into the furnaces respectively through launders. This new process is more advanced, more reliable and more environmentally friendly. Until now, this process in the GuoRun copper smelter is operating smoothly. An increasing number of projects which use this process are under design and construction in China. INTRODUCTION At present, there are many advanced smelting technologies for copper concentrate, such as oxygen bottom blowing smelting, flash smelting, top lance smelting (including ISA and Ausmelt furnaces smelting), side blowing smelting, Mitsubishi smelting, etc. At the same time, there are many copper matte converting technologies such as oxygen bottom blowing continuous converting, flash converting, Ausmelt top lance converting, horizontal multi-lances top blowing converting, Mitsubishi converting, P-S converter converting, etc. The final blister copper fire refining technology mostly adopts rotary anode furnace. Therefore, in the process of processing and extracting the copper from concentrate to produce anodes, there are dozens of technology combinations. Among them, the non-continuous converting technologies for molten or cold matte are often adopted in the converting process. The traditional P-S converting technology had been utilized for over one hundred years, with a mature, reliable and simple operation, also has advantages in the secondary scrap smelting of a wide range of quality. However, due to its batch operation, frequent roll in and out, poor sealing, considerable air infiltration, needs for ladles for molten phases transportation and other characteristics, the technology has a serious pollution problem due to fugitive SO2. At the same time, in the cold matte converting technology, the molten matte needs to be cooled and then processed. The sensible heat of the molten matte cannot be recovered, and the preparation process is needed in the process. Therefore, both energy consumption and investment are relatively higher.

Jan 1, 2019

By Manca PP, Lassandro R, Caranassios A, Massacci G, Ciccu R

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables on tool performance (cutting rate and bead wear) has been Elucidated.

Jan 1, 1992

By César Ugaz, Jorge Cardenas

Mitigating the vibrations resulting from a blasting rocks is one of the most common challenges that Peruvian mining has, since if this impact is not mitigated it can generate discomfort and altercations with neighboring communities and also puts the continuity of the mining project at risk. In that sense, we must establish control parameters to mitigate these effects as much as possible. As a starting point we must establish areas of interest that in this context would be the communities near the mine; first stage to carry out constant monitoring at these points, the registration of vibrations and noise is vital for the success of this control, with this information we can establish predictive models, the registration of elemental waves and the evaluation of human perception. In a second stage, this information allows us to make decisions in engineering such as the selection of delay times, elaboration of detonation sequence schemes, maximum amount of operating load per delay window, as well as the use of special load designs (Decks). There is a fear that these controls generate negative impacts to the process, referring to fragmentation, dig rate, throughput, etc. Since we limit the explosive load necessary for the results we need. To avoid this we use "Decks" type load designs under a sequencing between these under time calculations by elemental waves, which generate a reduction in vibrations up to 50%, also complying with strict regulations without affecting the power factors to comply with our performance indicators. Finally, in a third stage we must carry out a constant evaluation of results according to the progress of the mine.

Jan 26, 2026

By Michael J. Messel

OF the various minerals that occur in fibrous form known as asbestos, chrysotile is the variety most in demand for commercial uses, and, last year, over 683,000 tons of the various grades were produced in Canada and United States, exclusive of African and Russian production, which figures are uncertain. Production has not been able to keep up with the increased demand, and an acute shortage exists. Canada, Russia, and Africa are still the most important producers. However, Russia consumes most of its production at home and exports very little. The United States consumes over 60 pct of the total production and produces only about 4 pct of the total from deposits in Vermont and small quantities from Arizona. This paper will review mainly, some of the more recent developments concerned with the extraction and processing of this fibrous mineral for various industrial uses, such as textiles, insulation, building materials and brake linings.

Jan 1, 1949

By Mario Samamé Boggio

El presente trabajo describe el período de la Colonia dentro de la historia minera peruana. Dentro de esta época no se utilizó método alguno para su explotación y no hubo un adecuado manejo de recursos y energías. Posteriormente se describe la mita, expansión (Huancavelica, Huantajaya, Laicacota, Hualyacoc), así como se describe las minas de plata, oro, metalurgia colonial y la misión Nordenflicht.

Sep 1, 1983

By AIME AIME

THE following paragraphs comprise such information as the Secretary has been able to obtain concerning the members and associates whose deaths have been reported. Further particulars or corrections of errors, and biographical data concerning deceased members or associates not already noticed in this way, are solicited. [SECRETARY'S NOTE.-All of these notices have been revised, and some of then have been more or less completely prepared, by me. To those which contain more particularly the expression of my personal feeling, my initials have been appended. The labor of preparing or editing these paragraphs has been in many respects both welcome and interesting, on the one hand, and sorrowful, on the other. In going through the list, I have repeatedly felt like one who, visiting the Morgue, suddenly comes upon the pale face of a dear friend, of whose death lie was not aware ; and, even when this fact was known to me, the work of recording it has brought upon me a flood of recollections, almost preventing the discharge of that official duty. The list for 1907 seems to me to he peculiarly sad, comprising, as it does, so many sudden deaths by violence or accident, so many veterans, removed too soon, and so many young men whose early departure impoverishes the future, even more than the present. Probably, this feeling on my part is largely due to the circumstance that the increased membership of the Institute necessarily in¬volves an increase of the annual death-list. Probably, also, it is connected with the circumstance that during the first years of the history of the Institute-say from 1871 to 1880-it was joined by men of all ages, and that the death-rate is consequently now above the average which would result from the normal annual addition, principally of young men. And finally, I must admit that, as one of the original members of the Institute, and practically connected with it for nearly thirty-seven years as Acting President, President or Secretary, I am peculiarly impressed and depressed by the successive deaths of those who were my associates in the years of its early struggles and triumphs. I do not wish to inflict upon my younger colleagues the melancholy reflections of an increasingly lonesome old man. In fact, my prevailing mood concerning the Institute is not at all melancholy, but triumphant and hopeful. If I may be permitted to preach at all, I would enforce, from the texts given below, a moral which many of them declare so forcibly as to preclude the necessity of expository enforcements-namely, the duty of every one of us, old or young, to give to his brethren, as he goes along, and without waiting for some future occasion for a comprehensive and monumental contribution to technical literature, the results of his observation and experience. When I look at this list of names, my personal sorrow over many of them is drowned in my professional reflection as to each and all-How much has died with

Jan 1, 1908

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1940 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal Mining, B-Milling and Concen-tration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which was issued quarterly in 1940 but will be issued every other month in 1941. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysical Methods of Exploration are issued as separate pamphlets. An Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CONTRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute accord-ing to their registration by classes. CONTRIBUTIONS and other TECHNICAL PUBLICA-TIONS will be sent upon request. A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page; minimum charge, 25¢. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1.25 domestic, $1.35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2.50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7.80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum domestic, $6.60 foreign (metal mining, milling and concentration, Industrial Minerals Divi-sion, and mining geology papers.) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6.60 foreign. Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY is mailed each month. A member is entitled to one volume a year on his membership and he may purchase for $2.50 one copy of a volume not already received; additional copies of the same volume, $5. Nonmembers may pur-chase the volumes listed, at $5 each, plus 60 cents for Canadian or foreign postage. Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 50¢ each to members; to nonmembers 506 current issue and $1 each, back issues. Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4.00 foreign.

Jan 1, 1940

By B. McHenry, A. E. Wraith, P. J. Mackey

The Wallaroo smelter on the Yorke Peninsula, South Australia commenced smelting operations in 1861 treating ores from the nearby Moonta and Kadina mines. The plant expanded and modernized on several occasions and was a leader in the successful introduction of new technology to improve operations. It operated continuously until 1923 when local mines became exhausted; in the closing stages of the 19th century it was the largest copper smelter in the world outside of those in Swansea, Wales. In 1892 a small electrolytic refinery was established at Wallaroo, the first in Australia, based on principles developed by Elkington at Pembrey, Wales in 1869. The Wallaroo refinery was specifically built to recover gold and silver from copper produced by smelting gold-containing feed materials shipped from Western Australia. This first venture into electrolytic refining was replaced in 1903 by a somewhat larger refinery which, although modest in size for its time, with a capacity of about 1000 tonnes of cathode copper per year, was very productive in precious metals. Anode copper was produced by an updated version of the reverberatory-based Welsh process until 1910 when barrel-type pneumatic converters were introduced based on American practice; subsequently, anodes were cast by tapping the precious-metals rich "bottoms" portion of converter copper as produced at about one-fifth into the copper blow. The present paper describes the Wallaroo refinery, its anode supply and products, supported by initial observations on a sample of a Wallaroo cathode held in the collection of the South Australia Museum, Adelaide SA, Australia. INTRODUCTION Australia ranked 6th in the world for copper mine production in 2018, with an output of 918,000 tonnes of mined copper, after Chile, Peru, Congo, China and the USA; about 40% of Australian mined copper was smelted in the country. Interestingly, the world ranking of Australia in mined copper has, with a few variations, remained about the same for more than 100 years – of interest, it was also the 6th largest country for copper production at 21,089 tonnes in 1899. At that time, all or most of the copper was smelted in the country (Mackey, 2016). Copper was first discovered in Australia in 1842 in South Australia not far from Adelaide; additional copper discoveries in the region soon followed. At first, copper ore was shipped to Swansea, Wales for smelting (Bampton, 2003). However, in addition to the long, 150 day one-way sea passage, it seems Welsh smelters preferred higher grade of ores – these aspects and likely a mood in the new colony to be independent of Swansea (Evans, 2014) evidently encouraged local smelting at the mine sites using small, Welsh-type reverberatory furnaces fired with hardwood as fuel and operated by Welsh and Cornish migrants. The first large copper smelter in Australia commenced in 1848 at Bremer, near Callington some 60 km east of Adelaide. With larger discoveries on Yorke Peninsula, the Wallaroo copper smelter at Wallaroo Bay on the west coast of the peninsula commenced operations in 1861 (Bell & McCarthy, 2008). Thus began one of the most successful, and in its day, one of the most advanced and innovative plants in Australia if not the world. In the late 1860s, it was considered one of the largest copper smelters in the world (Bell & McCarthy, 2008)

Jan 1, 2019