Search Documents

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

The flow field and coal combustion process in a pilot-scale iron ore pelletizing kiln is simulated using a computational fluid dynamics (CFD) model. The objective of the work is to investigate how the thermal effects from the flame affect the flow field. As expected, the combustion process with the resulting temperature rise and volume expansion leads to an increase of the velocity in the kiln. Apart from that, the overall flow field looks similar regardless of whether combustion is present or not. The flow field though affects the combustion process by controlling the mixing rates of fuel and air, governing the flame propagation. This shows the importance of correctly predicting the flow field in this type of kiln, with a large amount of process gas circulating, in order to optimize the combustion process. The results also justify the use of down-scaled, geometrically similar, water models to investigate kiln aerodynamics in general and mixing properties in particular. Even if the heat release from the flame is neglected, valuable conclusions regarding the flow field can still be drawn.

Apr 20, 2021

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By F. D. Everett

The exploration work on a seleniferous tuff deposit near Lysite, Wyo., was confined chiefly to an area of approximately 1 square mile selected on the basis of prior examination and sampling work by the Bureau of Mines. This area was superficially explored by digging and sampling over 2,000 feet of trenches and 15 test pits. The surface sampling indicated that the deposit might contain a multimillion-ton reserve of easy-to-mine volcanic tuff assaying more than 0.01 percent Se. Later, 11 holes, ranging in depth from 57 to 135 feet and totaling 929.4 feet, were drilled under contract using a dry rotary drill. Samples for assay were cut at 5-foot intervals or at noticeable physical changes in the formation being drilled. Of the 206 samples assayed from the drilling, only 8 contained more than 0.005 percent selenium, and 2 of these assayed as high as 0.012 percent Se. Chemical analyses of samples obtained from six holes drilled by the Nugget Coal & Timber Co. to the south of the area explored by the Bureau of Mines showed that no selenium-bearing formations were encountered in that work. Two of 72 samples taken from 42 validation pits dug by claim holders contained more than 0.005 percent selenium. The exploratory work established that the selenium mineralization is erratically distributed in small irregular bodies and is not confined to any one tuff bed. Because of the lack of correlation between the infrequent showing of low-grade tuff, neither the extent nor grade of the reserves could be calculated.

Jan 1, 1957

By N J. Goodman

The HIsmelt technology was developed and proven in Western Australia (WA) after more than 30 years and several billion dollars of research and development. The HIsmelt technology was transferred to China and is now successfully operating at the Molong plant in Shandong Province, China using WA iron ore fines as the major feedstock. Several more plants are under construction in China, and the technology has been approved by the Chinese Government as an environmentally acceptable alternative to the blast furnace. The unique flexibility of the HIsmelt process offers multiple pathways to decarbonise the production of steel in the near future. These pathways include:  Use of sustainably grown biomass converted to Biochar to replace coal as the reductant.  Pre-reduction of iron ore fines using hydrogen or biomass to direct reduced iron (DRI) powder.  Capture of carbon dioxide from the HIsmelt off gas and geo-sequestration underground. These pathways are highly suitable for the Australian iron ore industry as they utilise:  The large areas of land and long growing season available in Australia for the production of large tonnages of sustainably grown biomass.  Coarse iron ore fines directly without the need for fine grinding and pelletising.  Existing oil, gas and other underground gas reservoirs to store carbon dioxide. The HIsmelt technology will allow Australia to transition from ‘Asia’s quarry’ to Asia’s supplier of low cost, low carbon and high quality metallics that are required to produce ‘green’ steel with net zero carbon dioxide emissions. In addition, HIsmelt pig iron can be converted locally into steel via electricarc or basic-oxygen steelmaking furnaces to supply all of Australia’s demand for green steel.

Nov 8, 2021

By C. H. Benedict

Largest and most important of the milling plants under construction during the year is the Morenci plant of the Phelps Dodge Corp., in Arizona, where plans are being rushed for production in 1942. Grate mills will be used for fine-grinding, and in the pilot plant, classifiers of the spiral type have the preference for the closed- circuit work. The flotation units will be chiefly of the pneumatic type, with some mechanical units as auxiliaries. The Fagergren, Pan American, and Agitair machines were left in the competition as the year closed. If the absence of European markets for finished products has dislocated the mining industry, fortunately the lack of raw materials required in the beneficiation of ores has not been serious. except possibly as to the inability to import flint grinding pebbles. Some of the less important gold mines still use pebbles for grinding as is also the practice in the comminution of nonmetallics used in various industries. T the Calumet & Hecla in the Lake A Superior copper district pebbles have been used exclusively in open- circuit grinding in the Hardinge mills treating the

Jan 1, 1941

By Harry E. Tufft

Data were obtained by the writer from a number of the large coul-mine operators in Illinois, on the consumption and cost of timber used in their mines and the quality of the timber now being used as compared with former years. This information supplemented by comparative date for previous years published in bulletins of the filinois Coal Mining Investigation series, and other sources, is presented below. This survey is part of a cooperative study with the . S. Forest Service, of the mine timber situation, with particular regard to the economies to be derived by better selection, preparation, and storage of timber, and especially treatment with preservatives to prolong the life. Geo. S. Rice, chief mining engineer of the J. S. Bureau of Mines, under whose general direction the work was done, gave valuable advice and criticism. R. B. Miller, State Forester, contributed helpful data which he had recent- ly obtained in an independent study of the mine-timber situation in Illinois.

Apr 1, 1923

By Robert G. Ditchburn

The NW caldera hydrothermal vent field at Brothers volcano, of the Kermadec-Tonga arc, has associated massive sulfide mineralization. This includes an abundance of black smoker chimneys that contain significant concentrations of copper, lead, zinc and gold (de Ronde et al., 2005; de Ronde et al, 2010, under review). [ ] The oldest volcanic massive sulphide (VMS) samples recovered so far from Brothers have been dated using radiometric methods at GNS Science and found to be c. 1000 years old. By contrast, a volcanic cone that has formed in the southern part of the caldera has no associated VMS. Only elemental sulphur and Fe-oxide crusts are present here, samples of which have been analysed for their trace elements. From d34S values of sulfates and native sulfur, and the volume of gas (dominated by CO2 and H2S) discharging at the cone site, elements being deposited here are considered more directly magmatic in origin (de Ronde et al., 2005; 2010 under review). It has been discovered that deep-seated changes in volcanic activity at Brothers affect the NW caldera and cone site simultaneously, though the mineralogy at each site is so very different. Thus, the cone site is being studied to determine if elements being deposited there can be used as predictors of potential future VMS mineralisation as similar sites have been found at other volcanoes along the Kermadec arc and elsewhere. The frequency of these deep-seated magmatic events is considered important in the formation of Cu-Au-rich mineralization along arcs. The analysis of Fe within resulting hydrothermal plumes (surveyed by surface vessels), and trace elements in rock and mineral samples, are used to help determine the influence of magmatic contributions to the hydrothermal system. To verify that plumes are a reliable proxy for hydrothermal events depositing iron on the seafloor, Fe-oxide crusts from Brothers volcano cone have been dated to see if their emplacement coincides with highly Fe-enriched plumes in the water column. The radiometric dating techniques developed for barite-rich VMS, i.e. using 228Ra and 226Ra, were unsuitable for the Fe-oxide crusts because 210Pb was the only isotope detected by gamma spectrometry. Therefore, new techniques using 210Pb, 10Be and arsenic have been established.

Jan 1, 2010

By Lucien Eaton

INCREASED mining activity during the past year has brought to light changes in mining practice and advances in technique, born and incubated in the period of depression from which the mining industry is now emerging. Although the tendency toward large output from individual mines has continued, a salutary trend is evident toward greater efficiency at small mines, in which the gold mines of Canada have led the way. Improvement in excavating machinery and washing plants for small placers has continued, and knowledge of the possibilities and limitations of this kind of equipment has increased. Greater portability through sectionalization has been the keynote. Power, shovels and draglines mounted on caterpillar treads move from one deposit to another under their own power, and floating washing plants mounted on pontoons can be taken down, moved, and set up again by a small crew of men in only a few days.

Jan 1, 1937

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By G. W. Govier

The origin and limitations of the conventional and empirical equation for the interpretation of the results of back pressure tests on gas wells are discussed. Difficulties in data interpretation arise from many causes, including Jack of flow stabilization, uncertainties in connection with the friction calculation, and the effect of turbulence near the sand face in the reservoir. A procedure is developed to ac-count for the turbulence effect. This is based upon the theoretical equation for laminar steady state flow and current knowledge of turbulent steady state flow. The procedure involves the expression of the equation for combined laminar-turbulent steady state flow in terms of a turbulence contribution factor. This factor. is shown to be dependent mainly upon the flow rate per unit of pay thickness and the reservoir permeability. The method of interpretation permits the use of judgment based upon the theory and present day under-standing of laminar-turbulent flow and is considered an improved method

Jan 1, 1961

By S. Chai

Waste dumps are widely used to discharge stripped mine wastes in open pit mining methods. As mining progresses, the height of the waste dumps will increase gradually, which may induce sliding failure once the height exceeds a critical value. Therefore, estimation of the maximum dumping height is crucial to the life-cycle use of a waste dump. However, published information about the maximum height of mine waste dumps are extremely rare. In this study, the maximum dumping height is estimated based on the strength-reduction technique by numerical simulations. The influences of dump geometry and properties on the maximum height are investigated. The results show that the maximum dump height decreases as the dump slope inclination angle α or the unit weight of dump materials γ increases, but decreases when the shear parameters of dump materials (cohesion c and internal friction angle ϕ) increase. The maximum height starts to increase with the ground inclination β when shear failure occurs at the interface between the dump and the base. Furthermore the effects of the dump width B, Young’s modulus E, and Poisson’s ratio μ of dump materials on the maximum height are almost insignificant. Good agreement was found between numerical results available in the literature and those obtained in this study.

Oct 1, 2022

By Ray Y. Lin, Sunil G. Warrier

"Low cost processing of metal matrix composites is an essential requirement for this class of materials to be acceptable in commercial application. In an effort to reduce the cost of processing of metal matrix composites, an infrared pressureless liquid infiltration technique has been developed. The salient features of infrared infiltration are that it is rapid, simple and a low cost process. The rapid processing capability causes very little oxide formation on the alloy resulting in both improved wetting and flow characteristics and reduced oxygen contamination in the composite. Thus, vacuum is normally not required. Using infrared inflltration, aluminum and titanium matrix composites have been prepared under an ambient argon atmosphere. Reinforcements in these composites include carbon fibers, silicon carbide Nicalon fibers and Textron's SCS fibers. Microstructural and mechanical test results indicate that completely consolidated composites with good fiber distribution, limited interfacial reaction and high mechanical properties can be manufactured by this process. IntroductionAluminum and titanium matrix composites reinforced with ceramic reinforcements are strong candidates for numerous applications in the aerospace and automotive industries. Aluminum matrix composites are commonly fabricated by either solid state vacuum hot pressing, liquid state pressure infiltration or squeeze casting [1]. Although liquid state pressure infiltration and squeeze casting has significant advantages over solid state processes, the requirement for pressure makes these composites uneconomical for large scale industrial application. Titanium matrix composites are primarily fabricated by solid state diffusion bonding [2]. Pressureless liquid infiltration can significantly reduce the cost of fabrication in both the composite systems. However, during pressureless infiltration processes, several complications concerning the wetting characteristics and chemical compatibility arise."

Jan 1, 1994

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

By Cleo G. Rall

The value of brine analyses in the study of petroleum-engineering problems was recognized early in the history of petroleum. The Bureau of Mines before 1928 had indicated in several reports.3/ ways in which analyses might be used. Because of the confusion resulting from attempts to correlate the work of different chemists using greatly varying methods of analysis and systems of computation and expression of results, a paper presenting the methods used by the Bureau of Mines was prepared and published in 1928. This system of determining the characteristic constituents of oil-field waters and of calculating and reporting results has been widely adopted by the petroleum industry. The earliest and most obvious use of water analyses is determination of the source of water infiltrating into petroleum and natural-gas wells. For this purpose it is necessary that an analysis of the connate water of the formation from which the oil is produced be available and that an analysis of the contaminated water be made. By comparing these analyses with those of connate waters from formations higher in the structure, the formation from which the infiltrating water comes may be identified.

Jan 1, 1953

By L. H. Banning

Recent dry-top electric smelting tests at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., indicate that a high-titanium slag and a good grade of pig iron can be produced from alluvial Idaho ilmenite. A total of 120 tons of concentrates were smelted during this investigation, to yield an average of 0.5 ton of slag and 0.3 ton of pig iron per ton of ilmenite. Power consumption averaged 1,400 kv.-hr. per ton of ilmenite, at a feed rate of 400 to 500 pounds per hour, when operating at an electrical energy input of 290 to 370 kilowatts. The optimum operating voltage appeared to be 110 volts, phase-to-phase. Graphite electrode consumption averaged 15.6 pounds per ton of ilmenite smelted. Magnesite furnace refractory withstood the corrosive action of the hot metal and slag better than carbon refractory.

Jan 1, 1955

By M. Mathiba

High CO2 fluxes associated with reclaimed coal mine spoils pose an environmental hazard where such sites are used for building. CO2 concentrations in excess of 25% have been reported in homes constructed on or down gradient of such spoils. The objective of this study was to investigate the effect of a mitigation trench used at one mine site on CO2 fluxes across the trench using chamber?based trace gas measurement. LI8100 automated CO2 flux system was used to measure CO2 fluxes from 32 sample points located across a deep mitigation trench on June 8 and 9. The maximum recorded fluxes were 7.29 and 8.18 µmol/m2/s, with averages of 4.15 and 5.50 µmol/m2/s, up and down-dip respectively. These preliminary results show CO2 flux is higher up-hill than down-hill at 95% significant level. This work shows that flux measurement can be used to investigate CO2 migration on reclaimed mine land. Further work is necessary to allow geostatistical modeling of the spatial variability of CO2 fluxes over reclaimed coal mine spoils. Knowledge gained would assist mining practitioners and regulators in reclamation planning for envisaged post-mining land uses.

Jan 1, 2010

A composite iron ore-reductant pellet is a mixture of fine iron ore and fines of coal/char/coke, bonded at essentially room temperature with sufficient green strength for subsequent handling. In ironmaking, these pellets offer the advantage of fast reduction, utilisation of fines, non-coking coal and coke breeze. The composite pellet-based alternative ironmaking processes constitute a promising route for ironmaking in future. The present paper is a brief review of kinetics and mechanism of reduction of iron oxides into iron and other associated reactions, when these pellets are heated to high temperature. It would draw significantly from investigations conducted by the author and his co-workers.

Jan 1, 1999

By T Isaksson, J Anderson

The procurement process for underground construction contracts, in particular those contacts involving tunnel boring machines (TBMs), is subject to many complex and inter-related variables, including national and local politics, public policy, community involvement and media attention û as well as strict environmental and legal requirements. Other restrictions include the time available to adequately investigate geotechnical conditions and viable technical options to determine the best construction methodologies û including selection of tunnel boring machine characteristics and, those construction means and methods suitable for the specific geotechnical and environmental conditions. The latter are, most often, quite imperfectly understood. æGetting it rightÆ implies that an optimal configuration û of machine type, characteristics and associated methodologies û can be found and successfully implemented for a particular project. æFrom the beginningÆ implies that the lack of time issue can be successfully resolved. Within an international context this paper highlights a number of issues of concern which relate to tunnel procurement systems and the ways in which certain key processes are managed during planning, design and construction. The authors argue that there is considerable room for improvement in the way tunnelling projects are undertaken and an approach is discussed which has the potential for substantial gains in cost and schedule and reduction of risk. Savings, however, may only be fully realised if the new methods can be fully implemented by all parties involved. This, we believe, will require the rejection of ætraditionalÆ forms of management and procurement with associated changes in the roles and responsibilities of owner, engineer and contractor. Additionally, risk identification, assessment and mitigation are essential cost and schedule control process which have, to this point, been underutilised by the underground construction industry.

Jan 1, 1999

By R. A. Pallanch

This paper, which describes the milling practice at the Midvale concentrator, is one of a series being prepared by the Bureau of Mines. The Midvale concentrator, a custom lead-zinc selective flotation plant, is in Salt Lake County, Utah, on a flat site several hundred yards east of the Jordan River and about 200 yards south of the Denver & Rio Grande Western Railroad tracks leading to Bingham Canyon. The site is at an elevation of about 50 feet above the river, the highest available location, thus allowing maximum storage of tailings.

Jan 1, 1931

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011