Search Documents

By Leopoldo Gutierrez

Eight oil sand ores with the bitumen content ranging between 3.6 and 15 wt.% and the fines content (-44 micrometers size fraction) between 9 and 69 vol.% were subjected to the standard alkali extraction test used to measure the degree of oxidation of metallurgical coals. The results showed that there is a strong correlation between the absorbance of extracted solutions at a wavelength of 520 nm and the ratio of the fines content to the bitumen content. The latter factor is directly relevant to assessing the extractability of bitumen from oil sand ores. Bitumen extraction tests showed that the bitumen recovery decreased from 90 % to 30 % when the absorbance at 520 nm increased from 0.23 to 0.64. A comparison of the UV/visible spectra of solutions obtained from the alkali extraction tests with solutions of Aldrich Humic Acids suggest that low bitumen/high fines oil sand ores release substantial amounts of organic matter very similar, if not identical, to humic acids. In contrast, high-bitumen and low-fines ores do not release as much of the organic matter, and UV spectra of these leached substances are quite different from those of humic acids. Overall, the results show that chemical composition of bitumen in the tested ores varies greatly with ore type and oxidation, and that the alkali extraction test is a promising technique to quickly assess the extractability of bitumen from a given ore type.

Sep 1, 2012

By Narasimha Mangadoddy, Balraju Vadlakonda

"Bubble size distribution, bubble rise velocity and gas and solids hold-up are the key major hydrodynamic parameters that are extensively used for column flotation design and performance evaluation. The distribution characteristics of mean gas hold-up is studied using electrical resistance tomography (ERT) coupled with pressure transducers (PT) in column flotation. The ERT technique facilitates non-invasive and nonintrusive visualization of different flow regimes even in the presence of particles in a column flotation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas hold-up and its radial distribution has been analysed for both two-phase and three phase flows. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the three-phase flow hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, are employed to explore the influence of parameters in two phase flow in column flotation. Mean gas and solids hold-up values extracted from ERT have been critically analysed for the column operating in various flow regimes. Gas hold-ups and solid hold-ups results using ERT are in very good agreement with conventional estimation and correlations obtained using pressure transmitter methods. Meanwhile, the results show that the gas hold-ups in the centre region increase constantly with an increase in the superficial gas velocity, whereas solid hold-ups distribution is very heterogeneous for high gas velocity. Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the 'inside' flow behaviour of gas –liquid–solid three phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is perhaps the most significant technological innovation in flotation machinery and its successful introduction in mineral processing plants. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker & Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena, Biswal, Das, & Reddy, 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on performance of column flotation (Finch, J.A.;Dobby, 1991). Many techniques have been developed that could be used to experimentally analyse the hydrodynamics of column flotation. Tomography techniques are well sound to investigate the hydrodynamics for process equipment. Among that, Electrical resistance tomography (ERT) has been used in various industrial investigations for visualization of the concentration profiles and characteristics of the fluid dynamics in gas–liquid two-phase systems (Wang, Dickin, & Mann, 1999; Williams, R.A; Wang, 2000). ERT is an imaging technique to analyse the internal flow behavior non-intrusively. ERT provide very useful tools for measuring and monitoring of column flotation process on line. Due to its high speed capability, low cost measurement, robust sensors, ERT is considered to be the most powerful tool among other tomography techniques such as positron emission tomography (PET), magnetic resonance imaging (MRI), optical and infrared tomography. Application of ERT has extended in process systems due to its improved speed of data acquisition, sensitivity, flexibility and noise immunity. In multiphase flow of bubble columns, gas hold-up and solid hold-up are explored by using the coupling of ERT and difference pressure method (Jin, Han, Yang, & He, 2010)."

Jan 1, 2016

By D. R. Rathburn

Jan 1, 1962

By M. J. Sanzotti

This paper examines the potential for controlling longwall-induced subsidence by pneumatically backstowing the void created by mining with waste rock, and having the process scheduled as a unit operation of the mining activity. Based on a review of background literature, interviews with representatives of various mining companies, public-interest groups, and state and federal regulatory agencies, a hypothetical case-study evaluation of pneumatic stowing in a southwestern Pennsylvania mine site was conducted. The study indicated that current stowing technology cannot keep pace with the production potential of U.S. longwall systems. Further, at the case-study mine site, concomitant stowing would reduce subsidence by only 50% of that incurred during full longwall caving, the longwall coal production rate would decrease from 4000 tons per shift in the non-stowing case to 1500 tons in the stowing case, and a preliminary cost analysis reveals that pneumatic stowing would add $5.25 to $10.50 to the operating cost of producing a ton of coal at the case-study site.

Jan 1, 1995

By Arno C. Fieldner

Coal for coke production is fundamentally necessary for the manufacture of pig iron , and pig iron must be had for making steel - a vital element in our modern industrial economy . In both World Wars , special effort by Government and industry was required to meet the emergency of greatly increased demands . In the first World War , lack of coke - oven capacity , rather than lack of coking coals , was the principal problem ; but in the second World War both oven capacity and coking -coal mining capacity were pushed to the utmost . Because of inadequate supply , it became necessary to allocate a part of the production of these coals from other fuel use to coke production . This was done by the Solid Fuels Administration . These experiences raised a question , during and after the war, as to the nature and amount of the minable reserves of coking coal suitable for the manufacture of metallurgical coke ; and to what extent the lower -rank and lowergrade coals could be utilized by improving preparation and by appropriately blonding different coals . Obviously , much investigation and research are required to find answers to these questions . Somo work was done by Governmental and industrial agencies during the war , and , fortunately , more has been undertaken since the close of It is the purpose of this paper to review briefly our fuel reserves , with special reference to coking coal , and to discuss the problems of utiliz . ing progressively poorer coking coals as the reserves of high - quality coals approach depletion .

Mar 1, 1950

By A. J. Kraemer

This report on the physical and chemical properties of typical crude oils of California is the eighth in a series which will cover the producing districts of the United States, and is supplementary to Serial 2595 of the Bureau of Mines, which includes discussion of results, summary tables, and selected typical analyses of California crudes. The present report contains additional individual analyses of crude, oils from the fields of Fresno, Kern, Los Angeles, Orange, and Ventura Counties.

Jan 1, 1924

By Zhijing Zhang

The management of hazardous wastes is important in a society which is increasingly concerned with environmental issues. Incinerators such as the slagging rotary kiln are widely used in the treatment of hazardous wastes. However, in order to assure a smooth operation of the rotary kiln, the melt should have both a low melting point and high fluidity. In this study, the fluidity of various hazardous waste rotary kiln slags was measured in terms of length of flow using the crucible test technique. It was found that the slags have melting points ranging from 1372 to 1424°C while their fluidities varied from 61-102 mm. The effect of addition of oxides on the fluidity of a slag containing 47 wt% SiO2 was also investigated. For this slag, additions of SiO2 (up to 56 wt%), FeO and Na20 increased fluidity, whereas the addition of CaO and A1203 resulted in lower fluidity values.

Jan 1, 2002

By HOWARND N. EAVENSON

THE year 1930 resembled the preceding one in the coal industry in continuing the era of falling prices and 'of the abandonment of unprofitable mines. Practically all coal prices fell, and in the steam sizes during the last half of the year this was particularly true, due to the small industrial demand. No new mines of any size were opened in the bituminous coal industry, but there was a steady increase in the number of cleaning plants of all kinds built in all fields. It is estimated that at least nine million tons per year were added to the previous total of washed coal. The largest washing plant started during the year was that of the Buckeye Coal Co., at Nemacolin, Pa., with a capacity of 650 tons per hour. Fig. 1 shows - the mixing-bin, conveyor galleries, washing-plant and skip hoist, and Fig. 2 the 120-ft. Dorr thickener for collecting the 48-mesh material from the wash water. Dryers are used for drying the steam coal product. The following statement by J. R. Campbell shows the effect of cleaning on Pittsburgh coal in Greene County: "With the advent of the 650-t.p.h. efficient washing plant in Greene County at the Nemacolin mine of the Buckeye Coal Co., it has undoubtedly been demonstrated that the potential coking-metallurgical coals of the county can be brought within the pale of the highest grade high-volatile coals for steel manufacture. A few months' operation indicates that 9% per cent ash in the raw coal can be easily reduced to under 7 per cent ash in the washed coal and the sulfur from 1.60 per cent in the run of mine to 1.20 per cent sulfur in the washed coal.

Jan 1, 1931

By K. G. Baxter, D. G. Dixon

The Sepon process plant utilises an autoclave to oxidize a flotation concentrate containing pyrite, residual copper minerals, and sulphur. The concentrate is produced from the residue of a preceding atmospheric copper leaching circuit. The function of the autoclave is to provide iron and acid for that atmospheric copper leaching circuit. The key issues in the operation of the autoclave are to maximise the production of acid and ferric ions and to avoid scaling issues related to sulphur balling in the autoclave. Scale control in the autoclave was examined using various dispersants and residue recycle without success. Operation of the autoclave at high temperature and high acidity addressed the scale issue through rapid oxidation of the sulphur and produced a ferric sulphate precipitate in the residue that could be re-leached to provide ferric iron. This paper presents the development steps followed, through batch and continuous piloting that resulted in an autoclave circuit design that addressed the above process requirements. Following definition of the process design basis, modelling of the autoclave operation was carried out to assist with engineering design. The model included thermodynamics and kinetics of oxidation of pyrite, elemental sulphur and covellite and also considered gas/liquid mixing, oxygen solubility as a function of temperature and solution composition, ferrous to ferric oxidation, gangue reactions with acid and precipitation/re-dissolution of basic ferric sulphate and alunite.

Jan 1, 2004

By Raphael Victor

The construction and modification of tunnels brings a requirement for precise measurement of convergence and divergence to safeguard the structure, maintain safety and provide the assurance needed to maintain efficient progress. Established methods include manual measurement using tape extensometers and automated methods using photogrammetry and automated total stations. Drawbacks include the need for frequent access, power supply, cabling, and cost. The paper describes how the development of reliable optical displacement sensors (ODS) has changed the landscape. ODS sensors are connected to a long-range wireless mesh communications network via a solar-powered gateway outside the tunnel, with data instantly transmitted to the internet. A sensor and its reflector target can be installed in 20 minutes and is maintenance free for a decade. Tunnel movement is measured to sub-millimeter precision with repeatability of ±0.15 mm. Integration of a triaxial tilt sensor allows slope distance to be converted to horizontal and vertical changes and allows rotational movement to be determined. Applications include new-build and long-term structural health monitoring. Case studies will be given, including the refurbishment of rail tunnels in Spain where the ODS measured movement during track lowering in a situation where no other automated system was considered viable.

Jun 13, 2023

By A T. Job, P R. McAree

There is significant value at stake in the mining industry from the implementation of new technologies that support the enhanced profitability and sustainability of mines. However, in order to realise this value, new technology must be implemented in a way that is both effective and sustainable. The industry has a mixed history for technology implementation that provides fertile ground for understanding what is necessary for innovation to deliver value. This paper describes early stage research investigating why this is so, with the aim of improving how to deliver value. Several case studies are provided covering both successful and unsuccessful technology interventions. The paper identifies the common factors that emerge from the case studies, and offers a path forward for further research in this area.CITATION:Job, A T and McAree, P R, 2017. Three case studies on the implementation of new technology in the mining industry, in Proceedings Iron Ore 2017, pp 407–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R. L. Loofbourow

Reasons for reexamining underground mining include: 1. The assurance that more deep deposits of useful minerals will be found. 2. The existence of deeply covered deposits of industrial minerals near large markets where quarries are becoming depleted or are lacking. 3. Surface property values, zoning and other limitations on open pit mining. 4. Expectation that underground space will be increasingly used for transportation, power plants, storage and similar purposes. 5. The improvements which have been made in underground mining. During the last three or four decades many changes and improvements have been made underground. All underground construction and mining has benefitted to some extent but the effect on the productivity of labor employed with some methods- has changed little and the use of these methods has declined. Productivity of labor in other methods has increased substantially. The relative usefulness of mining methods has changed and a vital industry, bituminous coal, has been returned to health. In this paper, consideration is limited to nine methods used with high productivity during the period under review. These methods are not necessarily better than others but they may be considered the prime methods in the sense that, in our economy, many, low grade ores, coal and the principal industrial minerals could hardly be produced by less productive means.2 Although most of the examples cited are from mining as such., the first four methods discussed can be used for the construction of stable excavations of various' shapes in sound rock.

Jan 1, 1967

By Muhammad Tawalbeh

The calculated temperature history of a single particle of MgCl2 hydrates when it came in contact with fused salt electrolyte at 650 °C was determined using the measured heat transfer coefficient for the molten salt bath at 650 °C. The calculations revealed that the entire interior of the particle reached the temperature required for the formation of MgOHCI from hydrated MgCl2 in less than 2 seconds. This was much less than the time required for dissolution of the prills as observed in experiments. It is very likely that the formation of MgOHCI during prill dehydration and dissolution is a result of hydrolysis in the interior of the prills.

Jan 1, 2004

By C. E. Wicks, F. E. Block, F. D. Stevenson

The vapor pressures of tungsten (VI ) chloride ( WC1 ) and hafnium ( IV ) iodide ( HFI ) were measured by a metal diaphragm technique . Vapor pressure values were obtained to permit calculation of the thermodynamic properties of the vaporization processes of the compounds . The vapor pressure data of WC16 are represented by the following equations for the liquid , B - solid , and a- solid over the temperature intervals indicated : - log P = 8.194 3,253 /T Liquid , 281.5 ° to 325 ° C : B - solid 230.0 ° to 281.5 ° C : log P a - solid 185.0 ° to 230.0 ° C : log Pam *** = 8.794 - 3,588 / T = 9.615 - 3,996 /T where T is the absolute temperature in degrees Kelvin . The heats of vaporization and sublimation are 14.9 , 16.4 , and 18.3 kcal / g mole , respectively . The entropy of vaporization at the normal boiling point , 330 ° C , was 24.3 eu . The fusion temperature , 281.5 ° C , and transition temperatures , 230.0 ° and 185 ° C , were found by thermal analysis .

Jan 1, 1964

By S. Dominguez, E. Gebrehiwot, S. Richardson, S. Sandoval

Copper electrowinning/electrorefining (EW/ER) is powered by direct current (DC) rectifiers that typically generate 30,000 to 70,000 amps and a bus-bus voltage of 200 to 500 volts DC. Tankhouses are designed so that DC current flows through “cell lines” which contain individual EW/ER cells electrically connected in series. Electrolyte composed of copper sulfate and sulfuric acid in water forms the “liquid conductor” that connects the metallic conductors in this circuit. In this setting, stray current is a DC current that strays from and therefore bypasses the tankhouse circuit by finding a path to ground, often through the electrolyte in pipelines that feed into and discharge from the cells, or through dried electrolyte (i.e. sulfate), which is also electrically conductive. Tankhouse workers can be exposed to shock hazards if they become part of a stray current path to ground. This presentation details examples of stray current shock hazards in electrolytic tankhouses and provides voltage and amperage measurements associated with stray current in these examples. A review of critical safety controls in EW/ER tankhouses that will mitigate the risk of employee shock from stray current is also provided. INTRODUCTION Electrolytic tankhouses are designed to deliver relatively large amperages of DC current to a series of electrolytic cells in which copper is plated out of solution using the classic anode-cathode pair geometry within each cell. Electrolyte is the “liquid conductor” that transfers current in between the metallic conductors of the cell. The metallic conductors include inter-cell copper bus bars and the anodes and cathodes themselves. It is sometimes forgotten that electrolyte as a conductor is capable of delivering DC current outside the designed circuit of a tankhouse. Stray current is a DC current that strays from the tankhouse electrical circuit by finding a path to follow other than the designed path. Safety becomes a concern when there is a risk of an employee becoming part of an accidental stray current path, thereby suffering an electrical shock. In 2016, Freeport-McMoRan (FMI) suffered a fatality at one of its copper electrowinning tankhouses. The forensic analysis concluded that stray current from the tankhouse rectifier contributed to the fatality. An employee accidentally fell into contact with a metal flange at the end of an HDPE pipe that was collecting cell overflow electrolyte from the tankhouse. DC current passed through the employee to ground, creating a shock that was judged to contribute to his death. The situation was exasperated because the employee was unconscious, and therefore was exposed to the stray current for several minutes before being found. In addition, the employee’s clothing was saturated with liquid, and the employee was found kneeling in puddled liquid on the ground. FMI immediately began an investigation into the root cause of the stray current that was measured at the scene. Sufficient electrolyte had accumulated in the HDPE pipe such that a continuous path was formed between it and electrolyte that was continuously overflowing from energized electrowinning cells. The metal flange on the pipe was the metallic conductor that carried the current to the employee from the electrolyte inside the pipe. Current then flowed through the employee to ground. Because of this incident, FMI undertook an extensive review of the hazards of stray current in EW/ER. FMI’s tankhouse workforce received a Tankhouse Electrical Safety training course developed in- house to insure worker understanding of stray current hazards. Tankhouse design changes were implemented to better insulate workers from stray current. Personal protective equipment (PPE) standards were also reviewed and changes made.

Jan 1, 2019

By D Pienaar, B McFadzean, C T. O’Connor

Collector and frother molecules in sulfide mineral flotation are thought to have separate roles in the flotation process, where the collector selectively hydrophobizes the mineral surface and the frother adsorbs onto the bubble surface, inhibiting bubble coalescence. Molecular interactions have been observed between these molecules which allow them to co-adsorb at each of the respective interfaces, improving pulp phase recovery. This study investigated the molecular interactions between sodium diethyl dithiophosphate (SDEDTP) and hexanol, and the mechanism by which these interactions improve the recovery of galena. In this study each of the respective interfaces were investigated for the adsorption of SDEDTP. The adsorption of SDEDTP on galena was measured by UV-Vis spectrophotometry and isothermal titration calorimetry. At the air-water interface foam stability and pulp bubble coalescence was used to quantitatively discern if there are interactions between SDEDTP and hexanol. Microflotation and induction time experiments were performed to determine the effect of SDEDTP, hexanol and their mixtures on mineral recovery and bubble-particle attachment. The results of all these tests were collated to determine if SDEDTP-hexanol mixtures synergistically improve sulfide mineral recovery. It was found that SDEDTP reduced bubble coalescence in the pulp demonstrating activity at the airwater interface. Together SDEDTP and hexanol synergistically enhanced foam stability. This indicated that there are attractive molecular interactions between these reagents. Even though DTP did not adsorb onto galena, DTP-frother mixtures synergistically improved the recovery and attachment probability of this mineral. Adsorption studies with aeration showed that DTP in the presence of a frother transfers from the air-water interface to the galena mineral-water interface during bubble-particle collision. It was proposed that the transfer of hexanol through the thin film enhanced the kinetics of film thinning between the bubble and the particle by destabilising the thin film thus improving pulp phase mineral recovery.

Aug 24, 2022

By E Oktay, I Yusufoglu, C Kahruman

Powder and spherical pellets of MoO2 were oxidised under controlled conditions in the temperature range 674-791 K at oxygen partial pressures of 8.1-30.4 kPa. Weight increase during the reaction was determined by thermogravimetric analysis. It was concluded that the reaction is 0.6th order with respect to oxygen concentation and that the activation energy is 148 kJ/mole. In experiments conducted with powder, fast transfer of reaction heat to the gas phase created isothermal conditions, but the temperature of pellets rose by a maximum of 54 K at 674 K and 105 K at 791 K. The rise in temperature caused structural changes such as sintering and crack formation, which had a considerable effect on the reaction rate. The findings should be taken into account in the design of equipment and choice of operating conditions for roasting MoS2

Jun 21, 1905

By R. C. Burton

One of the major problems encountered with recirculatory breathing apparatus presently used by mine rescue teams is that the inspired air becomes uncomfortably, and often dangerously, hot. This is also true with self-rescuers. It is well known that man can tolerate very high dry-bulb temperatures if the wet-bulb temperature is low, but not vice- versa. The maximum tolerable, wet-bulb temperature is about 42 °C (108 °F). A continuously inhaled wet-bulb temperature above this value can cause irreversible damage to the throat and lung tissue, and wet-bulb temperatures close to it cause extreme discomfort (1) and seriously retard the capability of the man to perform useful work. A theoretical analysis, combined with experimental results, has shown that it is the carbon dioxide absorbent that is the major cause of high wet-bulb temperatures of the inspired air in the Siebe Gorman Proto 4, and in the Draeger BG 174 apparatus, both of which are used by rescue teams on South African mines (2). In the Proto 4 apparatus, the absorbent for the carbon dioxide is soda lime (calcium hydroxide). The German Draeger BG 174 also uses this absorbent but under arduous conditions such as in hot environments (50 °C, 122 °F), the use of an alkali absorbent cartridge is recommended which consists mainly of caustic soda (sodium hydroxide). Lithium hydroxide is used in some apparatus in the United States. It is clear that different absorbents will produce different quantities of heat and moisture for a given rate of absorption of carbon dioxide. The proportion of this heat and moisture which is transferred to the user depends upon how much can be removed from the recirculating air between the absorbent and the mouthpiece. This paper discusses the present methods of heat removal and describes the design and test results of a prototype evaporative cooler.

Jan 1, 1980

By Larry D. Patts

Section 317(e) of the Federal Coal Mine Health & Safety Act of 1969 directed the Secretary of the Interior to prepare standards under which all working places in a mine shall be illuminated by permissible lighting while persons are working in such places. Section 317(e) further provides that such working places shall be illuminated within 18 months after such standards are promulgated. In accordance with this section of the Act, there was published in the Federal Register for December 91, 1970, a notice of proposed rulemaking which prescribed the illumination to be provided in the working places of underground coal mines. In light of written comments, suggestions, and objections to this proposed rulemaking, the proposedstandards were withdrawn and reproposed in the Federal Register for Wednesday, October 27,-19h. In light of further comments, suggestions, and objections, a public hearing was held on April 4, 1974, and standards were again reproposed and published in the Federal Register for April 1, 1976. Promulgation of the final lighting standards took place on October 1, 1976, which means that the underground coal mining industry must comply with face illumination requirements by April 1, 1978. As mentioned previously, the first proposed rulemaking for illumination of underground coal mines was published in the Federal Register on October 27. 1971. In early 1972, Consolidation Coal Company (Consol) and the United States Bureau of Mines agreed to a cooperative study of underground face illumination: Consol felt that expertise is this field would become increasingly important. Consol's initial efforts in illumination were aimed at investigating practical lighting systems for underground face equipment. We were concerned with installing unobtrusive lights which provided sufficient face illumination for safety, but at the same time were readily maintainable, electrically reliable, and physically sheltered from damage. We believe that our initial lighting systems did provide sufficient face lighting for safety, but because only prototype components were available for field testing, the resultant poor system reliability and maintainability necessitated drastic improvement before face lighting could become practical. Final Lighting Standards Deem Early Lighting Installations Out Of Compliance On April 1, 1976, the Federal Register contained the final version of the illumination standards (as they were later promulgated in October). When these illumination regulations and measurement techniques were defined and measuring instruments were available, Consol checked their lighting systems underground and determined that the systems were not in compliance with these final illumination standards. More Lighting Hardware Added In An Attempt To Achieve Compliance. After determining that all of our face lighting systems were not in compliance, we began adding additional lighting hardware in order to meet compliance with published regulations. Unfortunately, to date, we have not been able to meet compliance with practical lighting systems. We have determined from our field installations that the required additional lighting hardware, (to meet compliance) with its increased vulnerability and decreased reliability, renders the lighting systems impractical, if not impossible, to reasonably maintain. Our attempts to provide 0.06 footlamberts have also produced adverse operator reaction to the glare and to illumination systems in general. BCOA Members Ask MESA To Demonstrate Practicability Of Compliance With Regulations Industry concern about meeting the impending lighting regulations was mounting, and in May of 1976 a meeting between MESA and BCOA members was held to discuss lighting compliance problems. At this meeting, BCOA offered to work cooperatively with MESA in testing the practicability of various lighting systems mounted on underground mining equipment. Field tests were to be conducted by United States Steel Corporation, American Electric Power Service Corporation, and Consolidation Coal Company. The purpose of this underground field testing was to develop capability to provide adequate face illumination in a safe, workable manner which would not detract from efficiency of operation. BCOA members involved in this cooperative study were to submit necessary machine drawings, sketches, etc. to MESA in order that MESA could perform a "black-box" study and specify the type and location of luminaires to be installed on the test machines. MESA was confident that they could specify lighting systems that would be in compliance and would be practical so as not to detract from efficiency of operation. Consol was first to install lighting hardware under the BCOA/MESA cooperative agreement. As per MESA specifications, Control Products HgV luminaires were installed on a Joy 2BT-2H boring machine at the Williams Mine of Northern West Virginia Region. As of mid-October, 1976, Consol had approximately eight weeks operating experience with the lighting system on this boring machine underground and had drawn the following conclusions: The lighting system installed at Williams Mine (1) does not meet compliance with lighting standards as originally proposed by MESA, (2) does not provide illumination in a safe workable manner, and (3) will detract from efficiency of the mining operation due to operational delays. Although Consol has rearranged lights on this boring machine in an attempt to reduce operator objections, a practical lighting system which is "in compliance" has not been arrived at as of this writing.

Jan 1, 1979

By A. Haxhiaj, E. Haxhiaj

"The paper has as a studying object the issue of effective management of gasses’ heating and dusts in reductive melting process in lead (Pb) metallurgy. It also analyses the issue related to the usage and recycling of dusts and gasses in all pyro-metallurgical processes of technical lead production. The paper contains the analysis of technological process of separation of humidity, gasses, and dusts of valuable remainders in “Trepça” plant. Paper has the results of theoreticalexperimental studying, analytical and graphical of gasses thermal balance depending on height and composition of load, and the coke quantity on load for reductive melt in “Water-Jacket” furnaces. With thermal balance, having into consideration all parameters of heat in entry and exit depending on aforementioned factors we aimed to optimize the parameters of the process, keeping the attention to the minimization of energy consumption, and the overall influence on environment.1. IntroductionThe upper part of the furnace which is the study point of this paper lies from the reactions zone of Water-Jacket furnace and it also includes the furnace neck. In this zone has been elaborated the zonal material balance referenced third in the row. The separation of humidity, dusts, gases and lead with gases depends on many parameters like temperature, load composition, and height of load inserted in the furnace, and also the height of preheating zone in Water-jacket furnace. Lead oxidizes in reaction zone of the furnace and exhales with gases like dusts and small particles after which falls in worthy storage of Trepça plant and has negative effects in environment, and economic stability of reductive melting process of Water-jacket furnace. Thermal balance of gases in this zone depends on many factors; height and load composition, coke quantity in a load. The calculation has been done as the standard methodology of thermal calculation is done; moreover, by using a computer for mathematical models which enables very accurate results. We must emphasize that acquired and used heat in reaction zone and melted materials is calculated in others studies, so their influence in preheating zone is assumed."

Jan 1, 2010