Search Documents

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By J. D. Wright

This paper describes current milling practice at Endako Mines Ltd., a molybdenum producer in central British Columbia. The various steps in the crushing, grinding and flotation of the ore are outlined, with emphasis on the metallurgy of the latter operation. Tailings disposal and concentrate assaying methods are also described.

Jan 1, 1969

By J. A. Sanchidrián, P. Segarra, S. Gómez

Blasting is a common activity in mining that can cause significant damage in the remaining rock mass. The most commonly used method for predicting vibrations is the Swedish or Holmberg-Persson approach. It is a simple and fast method that uses empirical formulation to estimate the vibration levels based on the explosive charge weight, distance to the source, and other parameters. However, it has limited accuracy and does not consider the effect of free surfaces or other boundary conditions. On the other hand, recently developed methods as the full-field solution (FFS) can provide more accurate predictions of vibrations due to excitations provoked by cylindrical columns of explosive, but the inclusion of free surfaces in analytical methods is a challenging problem. This paper presents a new approach that includes free surfaces in the FFS to predict vibrations analytically in the near-field. The main obstacle to including free surfaces in the FFS was the belief that the solution was non-decoupleable in P- and SV-waves separately. The Heelan's approach was previously used to decouple them, but it only provides valid radiation patterns in the far-field and does not account for intrinsic attenuation. In this paper, we address this problem successfully, allowing for the inclusion of free surfaces in the FFS.

Jan 1, 2024

By M. G. Dellow, D. W. Hendriks

"In early 1988 the decision was made by Noranda Minerals Inc. to install pressure filters at the GECO mill to replace the vacuum disk filters and bunker-C fired rotary kiln dryers. Two filters were installed, one for copper concentrate and one for zinc concentrate. Completion of the project was scheduled for the third quarter of 1989. The filters were made operational in October 1989. Some work remains to be done yet on loadout conveyors for total project completion. Capital expenditures for the project have been approximately $2,700,000 to date. The paper describes the selection criteria for the filter, the installation, startup and associated problems.1. INTRODUCTIONThe filter model chosen for the project was the Verti-Press model VP-50-6(7) (Figures1 ,2 and 3) by Filtra Systems of Farmington Michigan, USA. The decision to purchase the Filtra Systems filter was based on gaining familiarity with a different, mechanically simpler pressure filter than the Larox design and to a lesser extent a necessity for repairs to the the disc filter, rotary kiln dryer system used at the GECO operation for its' copper and zinc concentrates. The fact that it is manufactured in North America was an important consideration. The same basic principles of pressure filtration as the Larox machine are used but the implementation is quite different and somewhat simplified with some interesting innovations. 2 filters were installed to allow direct and immediate comparison of the same machine on both fine and coarse materials. Copper concentrate is reground for cleaning on the flotation circuit while zinc is not. Screen analysis of composited samples of concentrates for 1988 indicated that expected copper concentrate would be approximately 66% minus 400 mesh and zinc 50% minus 400 mesh (Tables 1 & 2).The filter is composed of six horizontal chamber module layered vertically and held together in a frame by 1 O large bolts; torqued down to 4000 ft-lbs. 6 individual belts are used; each with its own drive system. The belts themselves are of a 3 piece design with a filter cloth portion, a support belt and a rubberized intermediate portion. They are held together with steel clipper lacings. A basic description (1) of the filter operation is as follows. ""The horizontal filler chamber is closed by hydraulically pressurizing seals across each end of the filter chamber to 200 psi. The feed pump then pumps slurry into the filter chamber. Suspended solids are retained on the filter belt and the filtered solution drains into a lower drip tray and flows from the filter by gravity. At the end of the filtration or feed cycle, a rubber diaphragm in the filter chamber is pressurized hydraulically to 100 psi pressure. This removes all free liquid from the filter chamber and the filter cake. After the diaphragms are retracted the filter cake is blown with compressed air to remove any residual cake moisture. The seals are then retracted and the belt is advanced to discharge the filter cakes. During the cake discharge the belts are washed with a spray header located at the drive end of the filter. The belt assemblies move one (1) complete revolution during the cake discharge cycle. The cycle automatically repeats until the filter is shut down by the operator."

Jan 1, 1990

By Michael MacMillan

AI is already changing how mining companies are seen, judged, and trusted. This paper discusses “reputation engineering,” a structured way to build trust in a world where AI systems summarize and evaluate everything a company says publicly. Using mining examples, emerging AI search trends, and real communication work, the paper explains why the next 12–18 months are a crucial window for action. It also provides a practical framework to help mining companies improve their visibility, accuracy, and consistency across both human and machine channels.

Feb 22, 2026

By R. N. Love, L. Goldman

"INTRODUCTION When tannin is present in a boiler water, it causes certain difficulties in many analytical testing procedures because of its colloidal action in interfering with the removal of suspended matter by filtration and also because of the color it imparts to the boiler water.For example, in any test for phosphate in boiler water the first step is to filter out of the sample all sludge and suspended solids. Calcium phosphate in the sludge would give high results if not completely removed. If tannin is present in the sample, the sludge and suspended matter tend to pass through the filter paper so that it is difficult to remove it all. It may even be that tannin makes some of the suspended material in the sample completely nonfilterable. If this is true, it would be necessary to destroy or remove the tannin from the sample before filtering to get complete removal of calcium phosphate from the sample. In addition, if the test used is a colorimetric one, the tannin causes interference by its own color.As the calorimetric phosphate test is so convenient for control purposes and the use of tannin for boiler water treatment has become common, it has become necessary to develop suitable methods for employing the colorimetric phosphate test for boiler waters containing tannin. In this paper three different methods for doing this arc described and studied."

Oct 1, 1946

By Youzhen Zhang

The drilling boom is the key component of a roof bolter, and it has significant impact on the performance, safety, and reliability of the overall working device. In this paper, the experimental modal parameters of a drilling boom at low frequencies are identified with the Laplace wavelet correlation filtering method. Based on the obtained experimental parameters, a finite element model of the drilling boom is revised using an optimization algorithm to improve its accuracy. The dynamics of the drilling boom are analyzed through its modal and harmonic response. As a result, an improvement for the drilling boom is proposed to fix the weak links and enhance the dynamic performance.

Jan 1, 2012

By Joseph Hamuyuni, Fiseha Tesfaye, Daniel Lindberg

E-waste management through traditional methods such as disposing in landfills, burning in incinerators or exporting abroad for disposal are no longer options due to the strict environmental regulations. Fortunately, the presence of valuable metals in the e-waste and increasing demand for the metals as well as complexities of the currently available primary raw materials make recycling an attractive and viable option both environmentally and economically. Moreover, it is efficient in terms of resource management by closing the loop of metals. Consequently, urban mining such as the recovery of precious metals from e-waste streams through sustainable recycling processes have emerged. The sustainable recycling practices address the scarcity of primary resources and reduce consumption of energy for metals production while managing environmental issues related to hazardous materials from the e-waste streams. In this paper, valuable metals recoveries from e-waste streams through pyrometallurgical and hydrometallurgical processes are critically reviewed. And, innovative ideas for different steps of the thermochemical processes in the valuable metals and energy recovery from the e-waste streams are discussed.

Mar 1, 2017

By D Jeffery, R Whittering, G Lane

Most aspects of process design are best addressed via bench scale or pilot plant scale test work. However, as experience is gained, fundamental or indicative data can provide more than adequate information to manage the risk associated with some process aspects of concentrator design.Historical precedence exists where minimal design test work has resulted in successful projects. On many occasions benchmarking, sometimes supported by fundamental data such as mineralogy, has been used to successfully develop effective process plant outcomes. Of course, this style of approach is most common with æfast trackÆ projects and often comes with the usual surprises that result from inadequate geometallurgy to define the project cash flow.This paper explores the risks and opportunities associated with the various facets of process development and design for a base metals concentrator. The paper is intended to provide guidance to project managers rather than address the technical aspects of process engineering.CITATION:Lane, G, Whittering, R and Jeffery, D, 2012. Benchmarking versus test work - How should you manage process risk?, in Proceedings Project Evaluation 2012 , pp 49-52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By Best W. N.

Discussion of the paper of W. N. BEST, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1527 to 1537. WILLIAM A. WILLIAMS, San Francisco, Cal.-I would like to ask whether .Mr. Best ever had any experience with an oil burner that used neither air nor steam? W. N. BEST, New York, N. Y.-Yes. This type is commonly known as the "mechanical spray burner" and uses oil heated under high pressure to above its vaporizing point. These burners are not as efficient as the atomizing type for the following reasons: 1. They produce a round flame which; as with any other type of burner, must pass over a flat surface. A round flame cannot fit a flat surface. 2. They do not evenly distribute the heat, resulting in localized heat. 3. The outlet through which the fuel passes is very small; so all gravities of oil, especially oil containing sand, cannot be burned. 4. Their construction is such that they must be cleaned frequently, as the residuum in the fuel clogs the burner. 5. The oil opening being small, the capacity of each burner is small, so that many burners must be used in a boiler or furnace. (The fewer burners there are, the more accurately they can be regulated.) In marine boilers, these burners are largely used, because they do not require either steam or air for atomization. However, there are other methods by which this objection to other types can be eliminated, such as by the use of a rotary blower and steam turbine engine, the exhaust front the engine passing into the engine condenser, thus obviating loss of water. Mechanical burners are rarely used in shops. I know of but one power plant using them. With mechanical burners, the fuel must be maintained at a high pressure. On board naval vessels, some mechanical burners demand an oil pressure of from 100 to 6001b. It is advisable to reduce the pressure as much as possible, as fractured pipes or fittings are particularly dangerous, for the heated oil escapes as a vapor. In such cases there is liability of an explosion caused by spontaneous combustion.

Jan 12, 1915

Geological hazards such as faulting, basement ridges, and zones of "thin" (< 6 m) coal have a major impact on mining economics of underground operations in Huntly Coalfield. Experience has shown that drillhole-based investigations do not yield sufficiently detailed models of the coal seam to allow management of the planning risks associated with these hazards. Consequently, operational performance is affected by unplanned costs associated with lower productivity, loss of coal reserves, and expensive strata control remedies in problem ground conditions. Huntly Coalfield is a challenging environment for acquisition of good quality seismic reflection data due to the very thick (10-85m) weathering layer. Since 1994, successful acquisition of 2D and 3D data has been achieved through a combination of careful testing of technical parameters and experimental trials prior to committing to production recording. High resolution seismic reflection (HRSR) is proving to be an investigations technique which generates accurate and reliable models of the coal seam and associated structures, such as normal faults and topography of the surface on which the coal seam rests. The HRSR technique has been applied and developed in the Okowhao Sector where Huntly East Mine is developing and extracting coal reserves. Results of a recent 3D survey demonstrate that this technique is capable of revolutionising risk management in mine planning for underground mines in structurally complicated coal deposits.

Jan 1, 1997

By M. Shriwas, F. Calizaya

"Controlled recirculation may be considered as a beneficial means in mines of cold climate, where heating of air is required, and in deep or extensive mines, where cooling of air is required. Controlled recirculation can be designed by proper sizing of the booster fans with respect to main fan. Intuitively, it seems that the buildup of methane at the face will cease when a steady state condition is attained, and also that, at that same time, the maximum concentration at the face will remain same as in the return air. This supposition is proved by mathematical analysis that considers uniform mixing of methane in air in successive cycles of recirculation. This study includes two scenarios to show the effect of controlled recirculation on methane concentration in a sample network. Firstly, when recirculation crosscut exists near the working face; secondly, when recirculation crosscut exists away from the working face. The later scenario shows lesser buildup of methane concentration than the former one. INTRODUCTION The controlled recirculation is designed purposefully to allow a partial fraction of used air that increases the air velocity due to increased quantity of air and consequently allows effective dilution of contaminants to improve local ventilation condition at the working face. It can be designed by proper sizing of booster fan with respect to main fan in a ventilation network. Controlled recirculation may be categorized as crosscut, in-line or combined system based upon the configuration of the booster fan locations in a district ventilation network. Research on controlled recirculation has shown numerous benefits of controlled recirculation especially in deep or extensive underground mines, where further heating or cooling is required (Calizaya 1990; McPherson 1993 and Jones, 1987). However, fear of buildup of concentration has misled the mining communities to view the controlled recirculation as a hazard and deprived the mining industry to derive benefits from recirculation. Intuitively, it seems that the buildup of methane at the face will cease when a steady state condition is attained, and also that, at that same time, the maximum concentration at the face will remain same as in the return air. This supposition is proved by mathematical analysis that considers uniform mixing of methane in air in successive cycles of recirculation. This study includes two scenarios to show the effect of controlled recirculation on methane concentration in a sample network. Firstly, when recirculation crosscut exists near the working face; secondly, when recirculation crosscut exists away from the working face. The later scenario result shows the less buildup of methane concentration than former scenario result."

Jan 1, 2016

By F. G. BREYER

ZINC metallurgists continue to follow with keen interest reports of successful results from the continuous retort plants at Palmerton, Pa., and Meadowbrook. W. Va. The new process had already demonstrated its ability to reduce the lead content of the metal and to effect savings in labor and fuel. The past year has shown that the retorts themselves can he built to last long enough so that the retort cost per ton of metal is lower than in past practice with small horizontal re- torts. A number of the latest type of retorts are reported to have been in continuous operation for over 18 months without a failure and are said to be still in good condition. This seems a complete answer to the last question which remained before continuous zinc smelting could he pronounced commercially practicable.

Jan 1, 1932

By N. J. Themelis

In the last two decades, the Outokumpu flash smelting process has become the dominant new technology for copper smelting and has? also been applied to the smelting of other metal sulfides. The application of oxygen enrichment and improvements in concentrate burner and furnace design have resulted in ever increasing smelting rates per unit volume of the reaction shaft. This paper examines the. rate phenomena taking place in the reaction shaft of the Outokumpu furnace and compares information obtained from a mathematical model of heat and mass transfer rates to results obtained in pi1ot tests conducted at Pori, Finland, and to actual performance of a number of flash smelters around the world. 2?

Jan 1, 1985

By G. W. Grove

The wearing of self-contained oxygen breathing apparatus, although relatively safe if proper precautions are taken, is dangerous if defective apparatus -is worn, if men with inadequate training, experience, and physical requirements are used, or if improper procedure is followed. This is proved by the fact that at least 26 men are known to have lost their lives while wearing-oxygen breathing apparatus since its introduction in this country about 35 years ago. Self-contained oxygen breathing apparatus, commonly called "mine rescue apparatus" and sometimes improperly referred to as "oxygen helmets," is the only equipment that can be used for respiratory protection against poisonous mine gases, regardless of concentration or against an atmosphere containing little or no oxygen.3/ Apparatus of this type was introduced in this country in 1907, and since that time it has been widely used in conducting rescue and recovery work after mine fires and explosions and in some other work. All oxygen breathing apparatus used in this country before 1918 was imported from Europe, and although this equipment provided safer, more rapid means of conducting recovery work after mine disasters, there were many mechanical deficiencies in the apparatus which resulted in the death of some of the wearers. This led to the research and experimental work by the Bureau of Mines that resulted in the development and manufacture of more reliable and efficient types of apparatus in this country.

Jan 1, 1944

By Foster Fraas

Calculations based on data related to the electrostatic precipitator illustrate the variation in the electric forces on a particle with change in position in the ionized field. The feeble forces in some separators are explained by the low field intensity at midpoint locations between the electrodes. When the particles are in contact with the exterior surface of a rotating cylindrical electrode, a high field intensity at the electrode surface combined with the image charge results in large electric forces. The permissible feed velocity increases as the square root of the electrode diameter, providing high values in efficiency and feed rate capacity, particularly in surface-to-mass ratio separations such as are encountered in secondary materials recycling operations.

Jan 1, 1971

By G. L. Neumann

Owing to the need for additional sources of supply of both zinc and lead following World War II, the Bureau of Mines investigated many abandoned lead-zinc mines in the eastern United States. A series of shallow veins in south-western St. Lawrence County has long been a subject of speculation. These veins, which average about 4 feet in width and cut across the bedding of the country rock at right angles, are filled with calcite-carrying galena and sphalerite. The deposits have been worked sporadically during the last 115 years. From 1837 to 1852 the Coal Hill, the North, and the Victoria mines near the village of Rossie were at their peak of activity. Other calcite veins were prospected and a small production was realized. The Bureau of Mines began diamond drilling May 1, 1950, under the general supervision of McHenry Mosier, chief, Mining Branch, Bureau of Mines, Region VIII, and under the immediate supervision of the author) who was project engineer, following the preliminary examination by Robert S. Sanford. A total of 3,870.2 feet was drilled in 18 holes on four of the numerous deposits scattered over Macomb and Rossie townships. Drilling was completed September 21, 1950.

Jan 1, 1952

By N Weatherstone

A consistent and reliable international approach to public reporting of a mining companyÆs main assets, its Mineral Resources and Mineral Reserves, has become of increasing importance in recent years with the rapid globalisation of the mining industry. Through the efforts of the Committee for Mineral Reserves International Reporting Standards (CRIRSCO), a committee representing national resource/reserve reporting committees in Australia, South Africa, UK/Ireland/Western Europe, Canada, USA and Chile, the reporting standards in most æwesternÆ countries use almost identical resource and reserve definitions and are generally around 90 - 95 per cent compatible. New codes based on the CRIRSCO model are being developed or considered in other countries, including Peru and the Philippines. This unified approach has provided the mining industry, regulators and investors with a common framework to report and interpret mineral resource and reserve estimates, thereby facilitating funding to the mining industry through improved investor understanding and confidence. The common reporting standards are reflected in the CRIRSCO International Template, available on CRIRSCOÆs web site, a document that is kept æliveÆ by reflecting the best of the most recently published CRIRSCO-type national standards. In a significant exception to this unified industry approach, the USA Securities and Exchange Commission (SEC) requires adherence to its own standard, only partly compatible with CRIRSCO-type standards, with adverse and costly implications for companies listed in the USA. A major industry submission was presented to SEC in April 2005 which, if accepted, would bring about considerable compatibility of CRIRSCO and SEC standards. The UN Economic Commission for Europe (UN-ECE) has, since 1992, been developing its Framework Classification (UNFC) as a single global system for harmonising all existing national and international resource/reserve reporting systems, covering both government and industry requirements and both the hydrocarbon and solid minerals sectors. While few mining companies report their resources and reserves using the UNFC, the system is accepted or is being examined as a basis for reporting by some governments, including those of Russia, China and India. The UN-ECE agreed in 1999 to incorporate CRIRSCO definitions into the UNFC for those categories of resources and reserves used for market-related reporting, but a more recent edition of the UNFC removed or changed the definitions, requiring re-engagement by CRIRSCO to ensure compatibility. Since 2005, CRIRSCO and the Society of Petroleum Engineers (SPE) have been involved in discussions with the International Accounting Standards Board (IASB), which plans to develop a new Accounting Standard for the Extractive Industries as part of its International Financial Reporting Standards. At the request of the IASB, CRIRSCO and SPE have been examining any potential for convergence of resource/reserve definitions between the mining and hydrocarbon industries. Each of these systems is described in this paper and high level comparisons made.

Jan 1, 2006

By P. E. Fitzgerald

ACIDIZING, as the terns is used in the petroleum production industry, involves the use of hydrochloric acid in predominantly limestone formations, resulting in the lowering of resistance offered to the flow of oil and gas through the oil-bearing formation, usually with resultant increased production. A number of articles have been written on the chemical treatment of oil and gas wells; a bibliography of these works will appear in Volume 123 of the Institute's TRANSACTIONS (1937), and a few other references are appended to this paper.

Jan 1, 1937