Search Documents

By Cristián Araya L.

A dynamic agglomeration, heap leaching, solvent extraction and electrowinning software, called NICO, has been developed in order to either design or simulate copper ore recovery plants. NICO contains a library of routines, each representing a unit operation or piece of equipment, which are assembled like a meccano to match almost any wet plant configuration. Routines include agglomeration or curing either in drums or belts, belt conveyors, heap stacking and reclaiming, heap leaching of oxide, sulfide or mixed copper ores, heap irrigation, drainage, ponds, mixer-settlers, filters, columns, coalescers, tanks, electrowinning cells, pumps, and all connections and related piping. All models are semi- phenomenological, i.e., they include all physical-chemical, mass, thermal, transport equations, which are required to represent as closely as possible the equipment or unit operation. However, operating experience has been incorporated into the model in order to make it simpler, faster and reliable. This experience has been tested in several plants in Chile since 1992. Site meteorological data is simulated also; in this way the model is responsive to weather conditions (temperature, solar radiation, ambient humidity, atmospheric pressure, wind velocity, etc). NICO has been used recently for design and optimization studies in copper plants in Chile like Radomiro Tomic, Collahuasi and Zaldivar. A user-friendly interface allows fast and comprehensive simulations. The entire plant is shown in a single graphic screen, so the user can see all the relevant information, and soft-keys are provided in order to change parameters on-line and watch their effect in final copper production in cathodes. Model also calculates and reports operating parameters, as well as estimated investments and operating costs.

Jan 1, 1999

By D. van Rensburg

Jointed rock slopes are generally stable, as there is no freedom of movement for blocks of rock. In an open- pit mining environment, blasting opens up space into which blocks of rock can fail, resulting in the common occurrence of slope failure. Prior to the blasting of a trim pattern, the immediate highwall is scaled, where loose rock material is removed by means of a mechanical scaler. As mining of the pit progresses, the height of the scaled highwall from the pit floor progressively increases. These highwalls are never scaled again for the remainder of the pit life, and time-dependant deterioration contributes to these highwalls becoming subject to rockfall and, sometimes, slope failure. This paper documents the development of a South African innovation, a remote-controlled mechanical highwall scaler, a world first for the mining industry. The scaler will enable open-pit highwalls to be scaled from crest to toe whenever the need arises. It will reduce the risk associated with highwalls and deliver on the Anglo American promise of producing safe, profitable platinum.

Jan 1, 2012

By Selwyn G. Blaylock

I.-THE HISTORY OF THE SYSTEM TO trace the history of the development of the Co-operative Committee System in The Consolidated Mining and Smelting Company of Canada, Limited, one must look backward about twenty years. In 1915 and 1916, the first years of the W ar to really affect Canadian life, there were sixteen hundred men working in the Trail plant. These men were, on the whole, a splendid body of men and pa trio tic to the core. They were almost one hundred percent organized, ninety-five percent of them be-longing to the Union of the Western Federation of Miners. Most of the tradesmen belonged to their craft unions as well. For example, there were ? local machinist, steel workers', electrician, boiler maker, bricklayer, and carpenter unions. The Company had always maintained an open-shop policy and refused to enforce membership in any union, but recognized the right of every man to belong to unions. The only exceptions have been the I.W.W. and the One Big Union. Both of these organizations have always been fought by the Company. By 1916, membership in the Western Federation being practically 100 per cent, the Company recognized this organization's authority to make agreements, and a wage and hour agreement was drawn up and signed by the Company and the local officials of the Union, and ratified and signed by the Head Office of the Union in Denver, Colorado. This agreement was for the duration of the war.

Jan 1, 1936

By Eric Forssberg, Mats Hallin

INTRODUCTION Evaluation and optimization of mineral processes has been going on since the the first plant started hundreds of years ago. A huge mass of knowledge has been collected since then. The main problem with this type of empirical knowledge of complex processes is that it is very difficult to formulate and document. The methods used for collecting the knowledge is not consistent but-varies with "he person" that does it. In the late 60's and early 70's efforts were made to use computer based techniques to evaluate process performance and to formulate process models for mineral processes. Models were developed, such as the flotation model by R. P. King (1973) which is still used to simulate flotation circuit behaviour. During the 70's. a number of mass balancing packages were developed together with process simulation packages. The industrial sector also made great efforts to develop and utilize computer based systems for process control and evaluation. The expert system that BOLIDEN created in 1974 at the Kristineberg plant was a remarkable achievement considering the hardware (CDC 3600) and the software tools (FORTRAN) available at that time. The main obstacle to successfully implement optimizing computer control of mineral processes was and still is the limited knowledge about the dynamics of complex processes. There are, however. many activities going on in this area today and it seems that the technology is very near a break through. Process evaluation is the most important tool to improve and maintain the optimal performance of a process. Today dedicated computer based techniques are used for fast and reliable screening of the processes. The stages in process evaluation consist of three basic steps: - Data acquisition, manually or by data logging. - Data refining, mass balancing and parameter calculation. - Data evaluation. The refined data can then be used for model construction/calibration and subsequently for process simulation. This paper describes two studies where the techniques mentioned above are used to evaluate and simulate

Jan 1, 1991

By S. I. Saif

The Key Anacon deposit lies about 6 miles northeast of the Brunswick NO.6 mine of Brunswick Mining and Smelting Corporation. Geological mapping, especially in the well-exposed Nepisiguit River section, geophysical data, and information from extensive underground and some surface drilling show that the rocks at Key Anacon are similar in many aspects of stratigraphy and structure to those of the Brunswick Mine area. They include narrow beds of fine acid volcanic material interpreted to be metatuff and volcanogenic metasediments. The massive sulphide ore body at Key Anacon lies immediately above these acidic rocks, in association with other chloritic, sideritic or magnetic iron-rich metasediments. The iron formation, which is similar to that associated with other orebodies in the district, is overlain by massive andesitic material. Four phases of structural deformation have been recognized in the Key Anacon area; they are similar in intensity and style to those of the Brunswick No. 6 mine area. The orebody lies in a zone of complex isoclinal folding along the flank of a major F2 fold (Key Anacon Syncline) and in general appears to be stratiform. The ore occurs in probable F2 parasitic folds, and this suggests a complicated structural geometry superimposed on the original beds. The general similarity of the mineralization at Key Anacon, together with its occurrence with other iron-rich metasediments between a footwall of acid volcanic material and overlying andesitic rocks, is suggestive of stratigraphic time-equivalence with the Brunswick zone . If so, the metavolcanics at Key Anacon might have been derived either from a center within the main volcanic pile to the west or from a smaller local center active at the same time. Alternatively, the Key Anacon ore could have been formed during a much older volcanic cycle. The solution to this aspect of the problem is the subject of a continuing study.

Jan 1, 1978

By Joe N. Magee

As part of the important program of promoting conservation and efficient utilization of petroleum, Bureau of Mines engineers are making studies of secondary oil-recovery projects throughout the United states and publishing reports setting forth the pertinent facts so that others may profit by the experience gained. This report presents the results of a study by engineers of the Bureau of Mines, stationed at Franklin, Pa., of secondary oil recovery in a part of the Cabin Creek field, Kanawha and Boone Counties, W. Va., where natural gas is injected into the reservoir to stimulate oil production. Most oil produced in the Appalachian region at present is obtained from stripper fields in which almost all natural energy has been dissipated. Secondary-recovery methods are used extensively in many oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering oil not produced by primary-production methods. The part of the Cabin Creek field reported in this study is shown in figure 1 and has been designated by the operator as project 4. In 1944 the developed area of the entire field was approximately 4,200 acres, and the area of project 4 was about 600 acres. In the developed area of the project the oil reservoir is in the Berea sandstone and occurs at 2,914 to 3,410 feet.

Jan 1, 1952

By D. P. Koistinen, K. E. Beu

THE application of the integrated intensity X-ray diffraction method to the measurement of retained austenite concentrations in hardened steels has been fully described.'-' In developing this particular method, the assumption was made that the samples used would have flat surfaces which were free from voids and in which austenite was homogeneously distributed. The original calculation procedure' was modified to include the constant factor G which relates the intensity of a given diffraction line to the concentration of the component giving rise to that line. In order to include A (0) in the constant factor G, it was further assumed that the geometrical conditions relating the X-ray beam, camera cylinder, and sample surface were precisely met.V has been demonstrated that these geometrical conditions can be met experimentally without difficulty in many cases;' however, for those samples which have irregular surfaces or where it is impossible to locate the sample in the proper position with respect to the X-ray beam and film cylinder, it is desirable to evaluate experimentally what effect these nonideal conditions have on the reliability of the austenite determination. This note decribes the results of such experiments. SAE 1095 bar stock was used throughout and all samples were heat-treated as follows: 1600°F for 1 hr in a neutral atmosphere, brine quench, and 300°F temper for 30 min. To control heat-treatment conditions as closely as possible, all samples were plated with 0.002 in. copper to protect the immediate surface from the heat-treating atmosphere. After heat treating, the samples were deplated electroly-tically so that only the copper was removed. The heat-treated surfaces thus obtained were nearly as bright and polished as the original surfaces before copper plating although no mechanical work was done on the samples after heat treating.

Jan 1, 1954

By Wesley T. Holmes II, Lloyd H. Banning

Electric - smelting studies were made on titaniferous materials obtained from the Klukwan and Snettisham , Alaska ; Choteau , Mont .; and Iron Mountain , Wyo . , deposits with the objective of determining the feasibility of producing pig iron and an enriched titania slag in one test series and pig iron alone in another test series . In addition , related studies were conducted to determine the amenability of Choteau crude ore to wet -magnetic separation and to determine the quality of steel that could be produced from the titaniferous pig iron . The continuous smelting tests were made in a three - phase , submerged - arc , electric furnace , and the laboratory steelmaking tests were made in a singlephase electric - arc furnace . A continuous , belt - type , wet - magnetic separator was used in conjunction with a ball mill and a spiral classifier in recovering titaniferous magnetite from the crude Choteau ore . Pig irons containing less than 0.05 percent phosphorus or sulfur were readily produced from the titaniferous materials ; iron recoveries ranged from 92 to 98 percent . The Choteau ore was ground to minus 65 - mesh to produce a concentrate containing 60 percent or more iron . The steel produced from the titaniferous pig iron was a high - quality product .

Jan 1, 1964

By H. J. McQueen

Pyro-reduction of ores to metal products developed markedly through the industrial revolution into the great depression. Nineteenth century resource and environmental sustainability were haphazardly improved by many process changes, although the motivation was primarily reduction in labor, feed stocks and fuel. Some notable achievements were coke and hot air for blast furnaces (later from waste heat stoves), puddling of wrought iron and steel ingot production with convertors advancing into oxygen use and continuous slab, billet and strip casting. Although advances in one sector were often counteracted by fall-backs in others, there was progress in that the resource consumption and pollution per unit of production was decreased. Improvements in the 2 decades following WW2 were mixed but popular notice of environmental hazards forced governments to legislate pollution controls and initiate steps in resource conservation. The energy crisis of the 1970’s saw an industrial energy-saving campaign and legislation of technology assessment procedures. Up until mid 18th Century, the training of iron masters depended on apprenticeship with some formalized knowledge from medieval books such as those of Biringuccio (1540) and Agricola (1556). The advances were very slow partly due to absence of scientific concepts of the smelting process. Nevertheless, some iron masters succeeded in improving the process and described procedures to instruct others. With the surge of steam power and the reverberatory puddling process for ductile wrought iron (WI), machinery changed from wood (iron strap reinforced) to WI machinery. With the clarification of the reduction and oxidation mechanisms by Cavendish and Lavoisier (~1780), productivity in iron production surged. The mechanical testing and microscopy of Kirkaldy (1862) spurred understanding of processing and properties of WI and steel. The various forms of C in steels were determined by chemists at the end of the 19th Century. It also became possible to control metal and slag chemistry in the open hearth furnace. But understanding of the transformations during heat treatment of steel only came in the first decades of the 20th Century.

Jan 1, 2012

By Williams DJ, Battino S

The rapid crushing technique for the measurement of gas content of coal consists of accelerating the rate of gas desorption from coal by crushing. This technique allows the determination of gas content in the space of hours rather than days or weeks as required for the traditional slow desorption technique. The crushing technique is used particularly when gas content determinations are urgently required for mine safety purposes. The method is now routinely used in underground coal mines of NSW and to a lesser extent in QLD. Despite the rapidity and efficiency of this method, concerns have been raised upon the reliability of the method to deliver accurate results. Experience in Australia has shown that there is in fact some discrepancy in results between gas laboratories using the rapid crush technique. The development of rapid crushing techniques for seam gas content measurements in Australia and the main causes of variability in the gas content test results were investigated. The gas laboratories participating in the gas content testing were CSIRO Division of Coal and Energy, BHP Technical Services and GeoGas Pty. Ltd.

Jan 1, 1998

By M. O. Holowaty, C. M. Squarcy

1750 to 1850: The scene shifts westward across the Alleghenys to the young town of Pittsburgh; charcoal gives way to mineral coal as furnaces grow larger and the blast is heated; above all, Pennsylvania iron is adding strength to the new Nation and building an empire in the West. TWO names are inseparably associated with the Pittsburgh iron industry-those of George Anschutz and John Hayden. The iron ore deposits of southeastern Pennsylvania were found and developed early in the 18th century, and several forges and furnaces were built and operated. It was only after the revolution that the iron men crossed the Susquehanna River, built furnaces in the neighborhood of ore deposits of Franklin County, then along the Juniata River and its valley. Juniata Iron found a ready market in the Pittsburgh area. However, difficulty in transporting it across the Allegheny Mountains induced iron mas¬ters to seek ore and plant locations in the Pittsburgh district. One of the first to reach this area was George Anschutz, who migrated to America in 1789 at the age of 36, reaching Pittsburgh in the fall of 1790. Anschutz immediately set out to organize an iron company in Pittsburgh, and was able to interest some residents in his project. After being informed of an iron ore deposit located only three miles out of town (on the site of the present 26th St. and the Allegheny River) he decided to build there his blast furnace and foundry plant. Total cost of the installation was $300. When the furnace was put in operation, Anschutz, now known as Red George, found that the ore deposit was only an insignificant one and would last no more than a few weeks. A new deposit was found on Roaring Run, in the southeastern corner of Armstrong County. Anschutz transported some of this ore to the mouth of Two Mile Run, where it was loaded on horse wagons and transported to the furnace. In this way, he operated off and on for several months, until the furnace was blown out in 1794. After working for a year as plant manager for John Probst at Langhorntown, he built the Hunting-

Jan 1, 1961

By J. F. Childs

"INTRODUCTION Comprehensive overviews of the world-class talc deposits and related prospects in Montana were published by Olson (1976) and by Berg (1979). Both of these compilations include detailed descriptions and maps of the talc deposits and occurrences and were followed by a regional map and summary descriptions of the talc deposits published by Van Gosen et al. (1998). More recent publications, descriptions and field guides for some of the deposits include Underwood et al. (2014), Cerino et al. (2007), and Cerino (2002). The present paper focuses on some of the more recent ideas regarding talc formation that have developed since the publication of the earlier overviews. Olson (1976) reported that talc production from the deposits in southwestern Montana was over 200,000 tons in 1974 and that talc production had doubled between 1969 and 1974. The last year for which the U.S. Geological Survey published production records for talc by state was 1993. Production in Montana in 1993 was 350,000 tonnes (Virta, 1994). Remaining reserves are substantial at all three of the producing mines in the district. Minerals Technologies Inc., the parent company of Barretts Minerals Inc., stated in its 2014 annual report that it has reserves of 2,791,000 tons of talc. Imerys stated in its financial report for 2014 that it had 19,638,000 tons of proven and probable talc reserves at its North American mines. Although the Imerys reserves were not reported by individual mines or states, a large proportion of the total reserves would likely consist of the reserves at the Yellowstone mine, located south of Ennis, Montana. Talc mined in southwestern Montana is of high purity and is the quality used in a wide variety of applications including paints, ceramics, plastics, rubber, coatings, agriculture, cosmetics, and pharmaceuticals. GEOLOGIC SYNOPSES FOR MAJOR MINES AND COMMENTS ON REGIONAL DISTRIBUTION OF TALC OCCURRENCES The general geology of southwestern Montana is shown in Figure 1along with the locations of the three producing talc deposits in the area and the extent of pre-Belt marbles that host all of the talc mines and prospects. The term “pre-Belt” is used in the present paper because zircon and other radiometric data developed in recent years indicates that the metamorphic rocks that form the crystalline basement for the middle Proterozoic Belt basin in the Dillon Tectonic Block of southwestern Montana includes both Archean and Paleoproterozoic rocks (O’Neill et al., 1996; Foster et al., 2006; McDonald et al., 2012). An envelope or “corridor” has been superimposed on the geology in Figure 1 which encompasses all of the talc deposits that have a significant resource. This “talc corridor” will be discussed in later sections of this report. The more important talc deposits are discussed in this report section."

Jan 1, 2016

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By R. M. Santmyers

"Quartz and silica not only occur in diversified forms in nature but find a multiplicity of uses in industry. The purpose of the present paper is to assemble brief summaries of the many widely differing industries engaged in the production and preparation of these minerals in their principal commercial forms. Due to the scope of the subject it was though advisable to divide the paper into three parts. Part I deals with the subject of quartz and silica in general. It also contains a flow sheet of silica from deposit to consumer (fig. 1). Part II covers the uses and other economic factors of quartz, quartzite, and sandstone, the varieties of silica found in consolidated form. Part III deals with sand and miscellaneous silicas such as tripoli and diatomite. A chart showing the major ramifications of these industries is presented herewith as an introduction to the more detailed discussion that follows.For a more intensive study of many branches of the quartz and silica industries the reader is referred especially to Bulletin 263 of the United States Bureau of Mines, Technology and Uses of Silica and Sand by W. M. Weigel. For annual statistics relative to silica and its products in the United States he is referred to the annual chapters of Mineral Resources of the United States, entitled ""Silica,"" ""Sand and Gravel,"" and ""Abrasives."" With respect to diatomite reference is made to Diatomite, by Paul Hatmaker, recently issued by the U. S. Bureau of Mines as Information Circular 6391. In preparing this paper the author has drawn freely from these sources as well as Marketing of Metals and Minerals, by J. E. Spurr and F. E. Wormser; Non-Metallic Minerals, Occurrence, Preparation and Utilization, by Raymond B. Ladoo; and Abrasives - Part I, Siliceous Abrasives, by V. L. Eardley-Wilmot, Report 573, Mines Brand, Department of Mines, Ottawa, 1927.Acknowledgment is also made to the Foote Mineral Co., which has published in Foote-Prints (vol. 2 of 1929 and vol. 1 of 1930), comprehensive reviews of the uses of crystal quartz in the optical industry and as piezo¬electric crystals.The various forms of silica have attracted attention from the earliest times, and the water-clear crystallized variety was known to the Greeks as""krystallos"" (clear ice), being supposed by them to have been formed from water by the intense cold of the Alps; hence the name ""crystal"" or more commonly ""rock crystal,"" applied to this variety. The name quartz is an old German word of uncertain origin used by G. Agricola in 1529.Silica or silica dioxide (Si02) either free or in combination with other elements constitutes 59.08 per cent of the lithosphere, and quartz alone represents fully 12 per cent` of all rocks. Next to the feldspar group quartz is the most abundant mineral in the earth's crust; and it appears in a greater number of varieties and modes of occurrence than any other mineral. Silica or quartz occurs in crystalline, cryptocrystalline, microcrystalline, and amorphous forms. The most common, however, is the crystalline form, which occurs as three minerals, quartz, tridymite, and crystobalite, and of these three tridymite and crystobalite are quite rare in nature."

Aug 1, 1931

By V. N. Mackiw, H. Veltman

"A process is described which permits the separate recovery of lead and zinc from complex low-grade sulphide concentrates such as are produced from the New Brunswick type of disseminated pyrite ores. This process calls for the preparation of a lead-zinc bulk concentrate from the original ore by flotation. The bulk concentrate is then oxidized under pressure in autoclaves in aqueous sulphuric acid solution, such as return electrolyte from zinc electrolysis. This yields a zinc sulphate solution and a residue containing lead sulphate, unaltered pyrite and elemental sulphur generated during the oxidation. After the oxidation, the leach slurry is briefly heated to above the melting point of elemental sulphur and then cooled. Thus, pellets containing pyrite and elemental sulphur are formed, and they are separated from the lead sulphate by screening and/or flotation. Laboratory tests have shown that about 95 per cent of the zinc and lead can be separately recovered from complex bulk concentrates. Process possibilities are discussed."

Jan 1, 1967

By C. C. Birch

Due to grade estimation uncertainty, two statistical errors can occur. The Type I error is where material is classified as ore and mined, despite the true value being below the break-even grade. This material is dilution. The Type II error is where the material is estimated to be below the cut-off grade and is classified as waste, although the true grade is actually above the break-even grade. This material is not mined and is lost. The uncertainty was assumed to follow a normal distribution in a previous study. For this study, estimated block values are compared to those determined after mining (the best estimate of the true grade). This actual data from four mines shows that the uncertainty follows a Laplace. There is no single solution regarding adjusting the cut-off grade away from the break-even grade, considering estimation uncertainty, that could be applied to all gold mines. However, adjusting the cut-off grade downwards (up to 22% for one mine) is noted when optimizing the profit considering grade uncertainties. This type of adjustment could open up significant mining areas and extend the life of the mine.

Jul 2, 2022

To develop a system which will effectively detect and extinguish fires in underground fueling areas while also providing a warning for nearby miners. Approach A system involving optical fire sensors. automatically-released dry chemical and aqueous film-forming fluid (AFFF) fire suppressants, and automatic alarms was designed from off-the-shelf, state-of-the-art components, and was in-mine tested at two mines in the two typical underground fueling area situations: fuel transfer areas and fuel storage areas. How It Works As mines become more mechanized, the number of fire hazards increases since fueling areas are more abundant. Fire hazards are especially serious in deep mines, since escape time is longer. To help solve this growing problem, the Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the National Fire Protection Association (NFPA), has developed and in-mine tested a cost-effective fueling area fire protection system. The system was designed to be rugged enough for reliable, long-term use, yet to utilize state-of-the-art, off-the-shelf components to maintain cost-effectiveness. The system consists of cross-zoned, ultraviolet flame sensors used for quick response to fire, and a dual-agent fire suppression subsystem. A dry chemical is used for fast fire -knockdown," and AFFF (or "light water") is used for long-term, fire-securing capability. The basic components of the system are shown in the schematic illustration.

Jan 1, 1982

By B Chi, A Mahanta, R A. M Maddever, O Dominguez

BHP Billiton, in collaboration with Sodern and CSIRO, has developed a downhole logging tool for measuring geochemistry in situ. The FastGradeTM 100 (alternatively, FG100), exploits pulsed fast and thermal neutron analysis (PFTNA) to analyse the rock. This method is based on the detection and measurement of characteristic gamma rays emitted from isotopes in the material that become briefly radioactive when they are bombarded with neutrons. The tool outputs raw spectra arising from three types of neutron interaction, namely, inelastic scattering, neutron capture and neutron activation, which occur in successive time-windows (Smith et al, 2015). The spectra contain peaks at specific energies that are characteristic of the different elements interacting with the neutrons, the gamma count of which is related to elemental concentration. BHP Billiton uses in-house data processing software to convert the measured spectra to elemental concentrations.Much work has been done to understand the tool response under a wide variety of environmental and operating conditions, including logging speed, borehole rugosity, the presence of cavities, water etc. Effort has also been directed at understanding and quantifying the current sources of error in our conventional assays due to sample collection, preparation, and laboratory instrumentation in order to use this information as a baseline to compare against the FastGradeTM 100 results.To date, the FastGradeTM 100 primary use has been as a verification tool (JORC, 2012). However, beyond this, it has considerable potential to improve productivity in both exploration and production environments due to its ability to provide geologists with assay results soon after a hole is drilled.This paper presents initial test work and tool performance, including accuracy and precision under various conditions. Results are illustrated by comparing tool measurements to assays from laboratory samples collected from both reverse circulation and diamond-drilled holes.CITATION:Chi, B, Maddever, R A M, Mahanta, A and Dominguez, O, 2017. Near real-time assay with downhole assay tool (FastGrade™ 100), in Proceedings Eighth World Conference on Sampling and Blending , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By J. Fujioka, Y. F. Gu, C. Cui, D. Ping, A. Sato, H. Harada

"A new kind of cast & wrought (C&W) Ni-Co base superalloys named as ""TMW alloys"" are developed recently for compressor or turbine disks of gas turbine engines in High Temperature Materials 21 Project at National Institute for Materials Science (NIMS) in Japan. These Ni-Co base superalloys combine the characters of two kinds of y- y' two-phase alloys (Ni-base and Co-18at%Ti alloys) and have higher tensile strength and creep resistance than C&W UNDIMET 720Li superalloy."

Jan 1, 2006

By A Hanna

Quarries around Auckland have reached or are reaching the ends of their lives, which raises issues about rehabilitation. Significant volumes of 'cleanfill' are generated by the City, particularly during phases of urban renewal and development. Emplacement of the fill in quarries removes the problem of fill disposal and provides an opportunity for restoration of the quarry site.There is a compatibility between quarrying and cleanfilling because at quarries:Truck routes are already established Neighbours are accustomed to the effects and appropriate buffer distances have been established Bringing fill into a site attracts aggregate sales and is very efficient. Fill originates from construction sites and ad-hoc excavations and therefore it is not surprising that sampling has shown the quality to be variable. Both Winstone and the Auckland Regional Council have surveyed undisturbed soils in the region to attempt to determine natural background levels of common contaminant substances. Comparison of these levels with delivered fill shows that a high proportion of delivered materials can be regarded as mildly contaminated. Therefore the term 'cleanfill' is, in the Auckland region at least, a misnomer and the term 'managed fill' has been adopted.Historically and presently the only control on quality of 'cleanfill' has been some visual inspection. This leaves the fill operator open to potential liability for creating a contaminated site. Implementation of controls at WinstoneÆs operations has progressed slowly, over some ten years. This is mainly due to the perception that mobility of contaminants within and out of the landfill will be very limited because of the near-neutral pH and abundance of clay minerals in the fill. The methods of control and results of environmental risk assessments at WinstoneÆs Puketutu Island Quarry will be briefly described.

Jan 1, 2002