Search Documents

By Summers D. A.

A mining machine has been designed and fabricated to mine coal from room and pillar operations combining high pressure waterjet cutting and mechanical fragmentation. Waterjets are used to slot the coal face with an advancing plow wedge then breaking out larger coal pieces. The machine has the following advantages: - simply built around a disassembled longwall chock and gathering arm loader apron; - few moving parts which are simply and inexpensively maintained; provides immediate roof support in the face working area; - coal produced is larger, with resulting lower preparation cost; - no dust is generated; - risk of spark generation is virtually eliminated.

Jan 1, 1992

By Paul W. Billwiller

Introduction In 1937, the Britannia Mining and Smelting Company, Limited, was carrying on an extensive exploratory diamond-drilling programme. Most of this drilling was done on the 4100 level, the lowest working level in the mine. One of the exploratory diamond-drill holes, at approximately 12,500 feet from the portal of the tunnel, encountered heavily mineralized stringers of chalcopyrite and sphalerite in silicified grey schist. The mineralization was encountered just to the hanging-wall of the green mottled schist at a point 350 feet south of the 4100 tunnel. To delimit this new orebody, drifts and cross-cuts were driven on 3500, 3800, and 4100 levels to the hanging-wall in the area of the projected mineralization. On the 3500 level, the top of the mineralized zone was encountered. The zone was thoroughly explored by drifting and diamond drilling. The mineralization, however, was not sufficiently concentrated to be of commercial grade. On the 3800 level, the zone was found to consist of disconnected stringers of chalcopyrite and pyrite. Drifting was continued to the west and a long lens-shaped area of grey schist containing fairly heavy stringers of chalcopyrite was delimited. This lens later proved to be very close to the top of the commercial mineralization of the No. 8 orebody. On the 4100 level, a diagonal cross-cut was driven to the footwall of the downward projection of the mineralized zone. Diamond-drill holes from this cross-cut indicated a zone of heavy mineralization. A drift was driven off the cross-cut parallel to the zone and some distance to the footwall of it. Further diamond drilling disclosed a mineralized zone approximately 300 feet long and 35 feet wide containing sphalerite, chalcopyrite, and pyrite. The foregoing development work indicated a fairly large lens of mineralization of sufficient concentration to be classed as ore between the 4100 and 3800 levels. To explore this mineralization at depth, long diamond drill holes, dipping at minus 57° and minus 80°, were planned from some point to the hanging-wall of the orebody. The 4100 level was not suitable for small development headings, due to wider gauge track and larger cars than on the levels above. Therefore, a raise was driven from the diagonal cross-cut on the 4100 level to a point some 70 feet above and just inside the footwall of the orebody. From the top of the raise, drifts were expanded east and west to delimit the ore zone. In addition, a long cross-cut was driven 350 feet to the hanging-wall, and drifts were opened east and west from the end of the cross-cut to provide diamond-drill stations for the exploration of the orebody at depth.

Jan 1, 1946

By William C. Miller

This report describes investigations by the Bureau of Mines designed to establish the noise level and spectrum of various types of pneumatic rock drills and to furnish information that would be useful in conducting sound measurements in mining environments and in reducing the noise generated in pneumatic drilling. These investigations show that (1) the noise generated by the drills in the frequencies below 100 cps is caused by the impact of the piston and drill steel, in the frequency range between 100 and 2,000 cps by the exhausting of air from the ports, and in the frequencies above 2,000 cps by the resonant frequencies of steel drill parts and of drill steel; (2) satisfactory instruments and instrumentation systems are available for field and laboratory measurements; (3) reliable sound measurements can be made in mining environments; and (4) devices can be developed that will abate the noise.

Jan 1, 1963

By C. Thomas Hillman

This Bureau of Mines report describes an investigation of factors influencing economic viability of a proposed system to mine and process manganese nodules. The system consists of hydraulic dredging and ammonia leach processing designed to recover three metals: nickel, copper, and cobalt. A ferromanganese recovery plant is a considered option. Annual capacity is 3 million dry metric tons (t) nodules. Aftertax rates of return (ROR's) of only 7.38 and 6.63 pct are predicted for three-and four-metal base scenarios, respectively. Sensitivity analyses indicate that variations in commodity prices, metal recoveries, and deposit grades produce similar incremental changes in ROR. Estimated cumulative effects of price variations are greatest. While three-metal operations generally yield higher predicted returns, potential increases in manganese price and process recovery could make four-metal operations most profitable. Maximum variations in both capital costs and three-metal operating costs result in ROR changes of about 25 pct. In contrast, four-metal ROR's exhibit variations to 70 pct. Even so only a best case analysis, utilizing favorable variations in all categories tested, generated ROR's approaching a level thought necessary to trigger company interest. Consequently, it is concluded that nodule mining will not take place in the foreseeable future without significant financial incentives.

Jan 1, 1985

By H. J. McQueen

Before 1950, hot working was simply deforming above the recrystallization point and gave a soft product compared to cold working. From 1960 onwards, improved testing in compression and torsion (stress, strain rate, temperature, quenching) provided valid specimens for microstructural analysis by polarized optical and transmission electron microscopy (TEM). Indeed, TEM was essential to uncovering the hot working mechanisms because it could distinguish between cold and hot substructures (dynamic recovery) in either initial or new grains (dynamic recrystallization). Over the years, teams at Concordia, McGill and UBC obtained NSERC support for students and equipment. CANMET built up a hot forming group having capabilities from high-rate cam-plastometer compression to rolling of experimental alloy billets; this was combined with latest metallographic instruments for fundamental research. Al alloys of every class (2000, 3000, 5000, 7000, 8000) were studied to understand the effects of solutes, precipitates, dispersoids and composites. The complex flow patterns in extrusion were clarified and modeled by finite element methods. Physical simulations of rolling schedules (up to 20 passes and reductions of 98%) by torsion provided evidence of microstructure development during both the passes and the softening intervals, thus clarifying development of texture in different alloys. The results frequently appeared in proceedings of Light Metals symposia and Canadian Metallurgical Quarterly

Jan 1, 2011

By Martin Hertzberg

In this Bureau of Mines study, an equation is derived for the limit burning velocity for divergent, spherical propagation from an ignition kernel of radius, r: (Su)e = ( ) . For flame propagation into a preexisting, stretching velocity gradient of magnitude dv/dx, the limit velocity is (Su)e = (a dv/dx)1/2. These formulations are shown to be equivalent to the fluid dynamic concepts of Damkoh1er, Kar10-vitz, and Markstein. Existing data for the b10woff limits of flames are shown to give excellent agreement with those concepts provided that proper account is taken of two dilution effects: composition dilution caused by entrainment and velocity gradient dilution caused by flow expansion. Approximate flow-field solutions are also derived for the unburned gas motion above an upward propagating, spherical flame kernel in buoyancy-induced flows. It is shown that;, the upward hemisphere propagates toward a stagnation plane in a counterflow configuration involving the balance between the combustion force, which accelerates the cold gas upward, and the buoyancy force that accelerates the cold gas downward. The position of the stagnation plane above the upward propagating hemisphere is related to the ratio of the buoyant velocity, vb, to the burning velocity, Suo Extinction of the upward propagating wave occurs by flame stretch in that counterflow configuration when n = Vb/Su begins to exceed the expansion ratio, Pu/Pb' and the wave is blown off by its own buoyancy-induced flow field.

Jan 1, 1984

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By R Blin, R Walde, R Belli, D Inaudi

A fiber optic distributed sensing system allows the monitoring of parameters useful to determine the short- and long-term behaviour of the structure in response to the external actions, including, eg seismic activities as well as long-term phenomena such as seepage, tunneling, sinkholes, and other geo-structural movements. Monitoring of large retaining structures with such a system provides direct strain/deformation and temperature measurements on the broad interior area with an arrangement of several sensing cable lines, enabling early detection, localisation and sizing of subsurface damages. Measurements are provided every meter along the entire sensing cable, this is particularly important in such cases where the location of defects and damages cannot be predicted. Fiber optic distributed sensing cables are generally available for retrofit installation inside the dam structure using trenches on the downstream face or laid during construction below the geomembrane liner within the bedding sand layer. Mapping the cable route enables exact correlation between a linear coordinate on the cable length and a position in the dam. Cable installation is envisaged to be carried out during further raising of the embankment; additional cable sections are plugged to the previously installed cables and measured with the existing measurement system, requiring only an update of the mapping. The measurement system is placed remotely from the sensing area since a section of sensing cable can be used to link to the sensing area at the storage facility several kilometers away. The system is available for on-line, 24/7 real-time operational data management. Such fiber optic distributed sensing systems allow storage facilities to be monitored with long, accurate, continuous and precise data for geotechnical diagnostic purposes. This contribution will introduce the principles, benefits, and limitations of this technology.

Jul 1, 2021

By S. H. Ash

THE MAGNITUDE of the anthracite industry's drainage problem in the Northern field of Pennsylvania is realized when it is known that, for the 8-year period 1944-51, all pumping plants in this region pumped an average volume of 112.5 billion gallons of water from the mines to the surface each year. This is over 214,000 gallons per minute pumped against an average hydrostatic head of 400 feet each year for that period (12).4 By comparison, Lake Wallenpaupack, the largest artificial body of water lying wholly in Pennsylvania, contains 71 billion gallons of water in its 24-square-mile area; the average volume of water pumped from the mines in the Northern field each year during the 8-year period was 58 percent more than the volume impounded in Lake Wallenpaupack. The natural configuration of the drainage area overlying the Northern field subdivides the total area into two major drainage areas-the Lackawanna River drainage area and the Susquehanna River drainage area overlying the Wyoming Basin. Although the 169-square-mile drainage area overlying the Wyoming Basin is slightly less than half that of the Lackawanna River drainage area (10), the total volume of water pumped to the surface from mines in the Wyoming Basin is 21 percent more than the total volume pumped to the surface from mines in the Lackawanna Basin. From this, it is apparent that the Susquehanna River and the pervious deposits in the buried valley over which it flows in its course across the coal measures of Wyoming Valley is the greatest single source of mine water affecting mines in this area. Because of its relatively flat terrain, the wide flood plain of Wyoming Valley does not facilitate rapid runoff; consequently, much of the surface water seeps directly into the buried-valley deposits and eventually into the mine workings.

Jan 1, 1953

By W. E. Crandall

The Star-Morning mine is a. 1000-ton-per-day lead-zinc producer located in the easterly part of the Coeur d'Alene Mining District of North Idaho. The property includes both the Star and Morning mines which are located on the westerly and easterly portions of the same complex of veins. The mine is 70% owned by the Bunker Hill Company (Gulf Resources, Inc.) of Kellogg, Idaho, 30% owned by Hecla Mining Company, and operated by Hecla Mining Company with head-quarters in Wallace, Idaho. One of the characteristics of mines in the Coeur d'Alene District is that many of the ore bodies extend to very great depths. The Star is no exception, but rather a leading example. The complex of near vertical veins and ore shoots extend some 7000 feet below the surface at present, with a maximum strike length of about 4000 feet. Ore has been mined on 20 separate veins and ore structures. More than 50 miles of headings have been driven and nearly 23 million tons of ore mined since the Morning mine started in.189S. The problems of mining at such depths are formidable temperature on the bottom level is 1100 F and high humidity problem. Pressure from the sheer weight of rock is as high foot. This paper will deal with providing a new access to the deeper levels of the mine and the installation of a hoist and related items to service these levels. By the time development had reached the 7100 level (Figure 1), it became apparent that a different 'hoisting system was going to be necessary if we were going to continue to mine at a profit. The main shaft extended to the 4000 level at which point a ?:3100"'foot winze shaft provided access to the 7100 level. The two hoists were limited to handling 3-ton payloads at 1200 to 1500 feet per minute. Some ores are still produced from above the 4000 level but as these ore reserves become depleted the hoisting of the desired tonnage (1000+/day-) from the lower levels of the mine would exceed the capacity of the existing hoisting system. A decision was made to sink a new vertical shaft at a point well in the south wall of the ore bodies where strong rocks and a minimum of faulting was expected and to purchase and install a new hoist capable of hoisting over 7000 feet. This new' shaft, designated as the No. 4 Shaft, was planned to reach 2000 feet below the 7100 level which was the deepest level at that time. The hoist would be in-stalled on the ,main 2000 Adit level which is used as an access and haulage level to the concentrator and surface plant in Burke.

Jan 1, 1971

By Arnold C. Love

This report discusses current research by the U.S. Bureau of Mines on the effects of whole-body vibration (WBV) and shock on underground mobile equipment operators. The highlights of a comprehensive literature review of WBV, shock, and seating are presented. Factors discussed include health and physiological effects, comfort, performance, and fatigue. Vibration data were collected from shuttle cars and ramcars at several underground coal mines in Pennsylvania, Ohio, and Illinois. The data were formatted so that they could be used to drive the Bureau's motion platform, and to compare them with ANSI S3-1979, Guide for the Evaluation of Human Exposure to Whole-Body Vibration. Human subject testing in the Bureau's vibration research laboratory evaluated the effects of two different seat angles and of the presence or absence of vibration and of foam padding on heart rate, blood pressure, and subjective discomfort. Only vibration significantly increased heart rate and systolic and mean blood pressures. Vibration and a steel seat had a significant effect on subjective discomfort. The apparatus used for these tests and the experimental procedures are described in detail. Recommendations are made for additional research on the exposure of underground mining machine operators to WBV and shock.

Jan 1, 2010

By P. R. Jones

A computer program was written for the design of a shell and tube type heat exchanger on a price optimum basis. The program was designed to meet the following requirements: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; and (4) no change in phase. Price optimum design was obtained for four standard tube sizes and standard pitch. Pressure drop both inside and outside were computed and the nearest standard shells having at least the required area were listed. With this information, the estimator can select the heat exchanger best suited for the need. The program was made adaptable to various fluids and to various tube sizes and spacing by reading in much of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1967

By T. S. Kagogo

The factors affecting haul truck tyre performance and the effectiveness of the management system at Rossing Uranium Mine were investigated with the aim of increasing tyre performance in terms of running hours until failure. The main objectives were to identify the types of tyre failure, their causes and cost implications, and evaluate the effectiveness of the management system. A site severity survey, weight study, and TKPH studies were conducted to determine the pit conditions, and an analysis of failed tyres carried out. The results showed that tyre performance at the mine has declined from 2009 to date, and the increase in lost value amounted to R5.7 million in 2012 alone. The main cause of tyre failure is loose rocks in the pit. The present management system in the load and haul department is not effective enough due to operational constraints it is facing.

Jan 1, 2014

By J R. M Hutcheson

Advocate Mines Limited came into initial production on June 30, 1963, with an annual capacity in excess of 60,000 tons of high-quality chrysotile asbestos fihres, thus strengthening Canada's position in world production. The history of this development is traced from discovery through initial exploration, financing, orebody delineation and evaluation, pilot-plant production and product evaluation, construction of the plant, construction of deep?-sea shipping facilities, provision for a closed shipping season, and provision for the remoteness and for the lack of services, through to realization of full production capacity. The many unique aspects of the project are given special attention, particularly in the light of the first year of full-capacity operation. The marketing of the products in a highly competitive world market is reviewed, with special emphasis on product evaluation, quality control and the shipping of high-quality products to consumers throughout the world. C ANADA'S newest asbestos producer, Advocate Mines Limited, is located at the north end of the Burlington Peninsula, White Bay District, Newfound-

Jan 1, 1965

By D. A. Baker, E. A. Gyawu, K. Awuah-Offei

Several underground coal mining disasters, such as Upper Big Branch in 2010, have revealed technological and organizational shortcomings related to self-escape. Efforts to address these gaps have primarily been top-down, that is, identified and implemented by upper management or external governing bodies. In contrast, this study employs a novel miner-centered approach to identify perceived technological boundaries to self-escape. Using a semi-structured, scenario-based survey, we elicit direct feedback from miners about current, emerging, and hypothetical technologies aimed at improving self-escape during mine emergencies. The results show a general high usefulness rating across all 21 technologies in the survey. Miners who work underground (both outby and working face miners) appear to give higher usefulness ratings overall than miners on the surface and other locations. This work will be directly applied to a series of proof of concept and prototype studies on self-contained self-rescuers (SCSRs), refuge alternatives (RA), and communication devises aimed at improving self-escape technologies through miner-centered research and design.

Mar 2, 2022

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By David R. Delling

Introduction In 1967, Tenneco acquired Kern County Land Co. The primary reason for the acquisition was to obtain Kern's agricultural, manufacturing, and oil interests. Included in the Kern portfolio were the core of Tenneco's present sodium leases in Sweetwater County, WY. This lease base has been ex¬panded and now consists of 62 km2 (24 sq miles). Beneath this property lies more than 500 Mt (550 million st) of economic trona ore. Following the Kern acquisition, Tenneco continued exploration and feasibility studies concerning the trona leases. The effort was accelerated in 1976. Tenneco was attracted to trona because of the favorable lease position it held, the growth rate of the Wyoming industry during the 1960s and 1970s, and the prospects for a long-term, stable business enterprise. The reserve picture was certainly attractive to a company long accustomed to the never-ending struggle to replace oil and gas reserves. In 1978, Wyoming was a boom area that had experienced rapid growth for a number of years. Unemployment was very low and vacant housing nonexistent. The prospects for soda ash were somewhat different in the 1970s than now. But it was recognized even then that a new producer would have a challenging task to compete in this business. Tenneco knew the capital burden required to build a grassroots facility during inflationary time, would have to be offset elsewhere Since labor and energy are the dominant direct costs in mining trona and producing soda ash these factors have always received a great deal of attention. Contracting and permits Environmental monitoring on the site began in late 1977. With the already mentioned considerations in mind, engineering began by mid-1978. Brown & Root Inc. was selected as the general contractor for the project. S. A. Scott & Co. was the engineering subcontractor for the mine shafts, hoists, ventilation system, and miscellaneous mine facilities. Frontier-Kemper was awarded the contract for sinking the two mine shafts. Acquisition of numerous federal, state, and local permits occupied all of 1978 and 1979. The Wyoming Industrial Siting Permit, which addresses socioeconomic issues, drew the most public interest. Siting issues were all satisfactorily resolved by negotiating reasonable stipulations with various local governmental units, school districts, and the like. Site location The Green River project location is not truly remote. It is located within 5 km (3 miles) of Interstate 80 and only about 32 km (20 miles) west of the city of Green River. Nevertheless, a substantial investment had to be made in communication and utility links to the site. These included: • A 14-km (8.5-mile) rail spur connecting with the Union Pacific Railroad at Bryan, WY. This spur has four bridge structures including one crossing Interstate 80. Most soda ash is shipped by rail, and coal is received over this line as well. • A paved 5-km (3-mile) roadway connecting to Interstate 80. • A powerline extension of about 27 km (16.5 miles), along with two new substations. • A 24-km (15-mile) waterline connecting the plant to a pump station on the Green River. The site is located on gently sloping terrain at an elevation of about 2.1 km (6800 ft). Ground conditions are good for construction. Weathered bedrock lies near the surface in most places. Geology The general geology of the Green River Basin has been well described previously. Tenneco's ore is in several superimposed evaporate beds. But the bulk of it is present in Bed 17, located about 457 m

Jan 10, 1985

By John D. Ridge

Here are summarized 162 papers, published between 1933 and 1967, that deal with various aspects of ore genesis. Emphasis is placed on additions to, or modifications of, ore-formation theory, no matter what type of deposit is discussed. More space is given to papers on the formation of base-metal sulfides solely because more papers are written on this subject. The final conclusion is reached that a chemically and geologically sound theory for the genesis of ore deposits can be built around the concept of concentration of ore e’ements in a magmatically produced ore fluid and around such surface processes as may act to concentrate economically valuable materials from rocks of any origin exposed at the surface.

Jan 1, 1968

By Francois Reizine

Infrared sensors will include scanning detectors and positioning sensors. The focus will be on 1, 2, and 4-color wavelength pyrometer systems which allow the accurate measurement of emissivity and, consequently, of the true temperature even in the presence of scale, slag, and fumes. Such sensors are being used in blast furnaces, BOF's, and galvanizing lines. Laser sensors will be presented using different principles of physics, mainly time-of-flight, pulsed infrared lasers for level measurement and dimensional measurement; triangulation lasers for width and thickness measurements; and laser Doppler velocimeters for velocity and length measurements, including mass flow, elongation, and tension control, cut-to-length applications. These sensors and systems are based on state-of-the-art technical developments to improve productivity and quality and reduce maintenance and downtime.

Jan 1, 2001