Search Documents

By Erik C. Westman

Knowledge of the orientation and relative magnitude of in-situ stresses at the mine scale is important for safe and efficient production from an underground mine. With this knowledge, stope location and scheduling can be optimized. Passive seismic tomography was used for imaging horizontal stress distribution at the mine scale. Microseismic measurements from the Creighton mine were used as input for the tomography calculations. The double-difference tomography algorithm was used, which provides the most precise results. The results clearly show a low velocity zone in the previously mined areas bounded by two high-velocity lobes located adjacent to the mined openings at locations consistent with those expected due to the horizontal stresses at the mine. The overarching goal of the research is to provide a tool that can augment both numerical modeling results and underground geotechnical measurements to allow the mine operator to produce in the safest and most efficient manner possible.

Jun 1, 2012

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibration limits for buildings with respect to ground vibrations from pile driving published in international standards are reviewed. At first, relevant vibration parameters are defined and the evaluation of vibration records is described. The sensitivity of structures to different vibration parameters (displacement, velocity and acceleration) is discussed. Most vibration standards relate to blasting activities, the dynamic characteristics of which can be significantly different to those from construction activities and in particular, pile driving. Several vibration standards are reviewed. The Swedish vibration standard is described in detail, as it is the only one accounting for several important factors, such as ground conditions, building material, and type of building foundation. Many standards limit the guidance to values based on the dominant vibration frequency and a wide scatter of frequency-dependent vibration limits exists. It is difficult to compare limiting values of ground vibrations proposed in different standards.1. INTRODUCTIONFor poor ground conditions, placing structures on piles is the most common foundation solution, while sheet piles are widely used to support deep excavations. Piles and sheet piles must often be installed in the close vicinity to buildings, structures or installations in the ground, which can be affected by ground movements and vibrations, (Massarsch and Fellenius, 2014). In many areas, environmental concerns with respect to noise and ground vibrations can restrict or even prohibit driving of piles or sheet piles or reduce the efficiency of installation. The design engineer must prescribe – often at an early stage of a project — the permissible levels of ground vibrations in order to minimize the potential risk of building damage. When seeking guidance from the literature, little or practically no applicable information can be found on how to assess permissible levels of ground vibrations."

Jan 1, 2014

By B. Ignasiak

Laboratory studies suggest that improvements of coke strength brought about by pre-heating caking coals before carbonization accrue from inadvertent oxidation rather than from other low-temperature changes in the coal mass. Controlled oxidation of highly caking coal, followed by laboratory carbonization, produces cokes which, in terms of a laboratory scale tumble test index, are equivalent to those obtained from prime metallurgical blends. Appropriately formulated blends of exhaustively oxidized and fresh caking coal similarly yield cokes with strength indices comparable to those of cokes made from the same coal after oxidation under optimum conditions.

Jan 1, 1979

By J P. Clark

Industrial minerals contribute about 50% of the NZ$1.2 billion generated annually by the minerals industry in New Zealand. The value is supplemented by a further NZ$500 million of minerals imported to supply our vital agricultural and industrial activity. As globalisation of the world's economy precedes, sources of minerals are being processed by fewer companies giving an ever-increasing control over global markets. If only to protect its primary production New Zealand needs to aggressively develop its mineral resources. The successful development of a deposit requires identification of the preferred market. While low-value aggregates dominate New Zealand industrial mineral production it is more specialised minerals supplied to the manufacturing and industrial sectors that provide more value per tonne. Minerals that have highly desirable intrinsic properties, or through value-added processing provide desirable properties, have the ability to fill niche markets both locally and overseas. Research and development towards enhancement or creation of desirable mineral properties could benefit New Zealand with both increased mineral potential and export of technological information. But, it is nearly always the market not the resource that dictates the viability of an industrial mineral and, with the globalisation of industrial mineral markets resulting in fewer but larger companies, any supplier must be ready to explore niche markets in order to compete on a more global basis.

Jan 1, 2000

By B. E. MacNab

During the past several years, Raymond Kaiser Engineers has prepared numerous studies concerning the technical and economic feasibility of coal exporting facilities in the western United States. Perhaps the most striking conclusion to be drawn from these efforts is that many people underestimate the complexity of the highly competitive, dynamic coal marketing system which includes coal loading terminals as an essential but relatively low-cost link in the energy production and delivery chain. The title of this paper, "The Status of Western United States Coal Ports - An Economic Assessment," should not delude anyone into thinking that the future of western U.S. coal- exporting ports has now congealed into a well- defined economic plan. As this paper will demonstrate, the situation is complex and more dynamic than ever and promises to remain so into the late 1980's.

Jan 1, 1982

By R. W. Thompkins

In order to evaluate the impact of air quality control on mine design, a few examples are given of cases in wh.ich ventilation has affected the economics of the total design problem. Principles for the drainage of gas contaminants are shown, and the contamination control problems created by differential pressures in complicated booster fan installations are discussed. The paper also deals with the use of advanced mathematics for solving some of the ventilation problems likely to be encountered.

Jan 1, 1967

By S Jahanshahi

In an earlier LCA study, the authors showed that the electricity consumption of the electric furnaces used in the production of the ferronickel and ferrochrome feedstocks made significant contributions towards the Gross Energy Requirement (GER) of stainless steel production, on a æcradle-to-gateÆ basis. Given the relatively low efficiencies associated with electrical power generation, substantial reductions in the GER for stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel and ferrochromium smelting stages.In view of these findings, a follow-up study was undertaken to investigate the likely environmental benefits of using bath smelting processes for the production of ferronickel and ferrochromium compared to the traditional rotary kiln-electric furnace processes, but still utilising the electric furnace process for stainless steel production. The METSIM process simulation software package was used to set up models of the two bath smelting processes and provide process energy requirements that were incorporated into the LCA. The environmental impacts considered in the LCA were greenhouse (Global Warming Potential, GWP) and acid rain gas (Acidification Potential, AP) emissions and solid waste emissions.The results of the study showed that the bath smelting route reduced the GER for ferronickel production by about 37 per cent over the traditional route, which translated to about a 21 per cent reduction in the GER for stainless steel. The corresponding reduction for ferrochromium was about half that for ferronickel, and when combined with the ferronickel result gave a 25 per cent reduction in the GER for stainless steel production. Similar reductions were also observed for the GWP and to a lesser extent the AP for both feedstocks, as all primary energy inputs were essentially fossil fuel based. Substantial reductions in solid waste emissions were also indicated for the direct use of ores in smelting. By utilising bath smelting processes for the production of the ferronickel and ferrochromium feedstocks, stainless steelÆs suitability for meeting many of the goals necessary for sustainable development, already recognised because of its particular properties, would be even further enhanced.

Jan 1, 2004

By Grégory Miette

The paper deals with a process that allows the recycling in a cupola of EAF dusts with 18 % Zn. It produces dusts with zinc grade higher than 50 - 55 % and commercial cast iron with less than 200 ppm Zn, 50 ppm Pb, 0.15 % S. The paper focuses mainly on lab tests made with the aim to develop an effective formulation of self reducing - melting pellets. With such a formulation, agglomerates develop a breaking load higher than 125 - 150 kg without any thermal treatment. Zinc and lead are volatilized in the cupola with yields higher than 95 % at 1200 OC, before any melting. Sulphur is transfemed into gas and slag. All these conditions allow to lower zinc, lead and sulphur grades below the cast iron specifications. Results of first bench scale tests performed at Fonderie Piret to validate the process will be presented.

Jan 1, 2002

By C. M. Mason

Bureau of Mines studies were made on the sensitivity of several ammonium nitrate-fuel oil (AN-FO) mixtures to bullet impact. The experimental work was done with one military rifle and two high-velocity sporting rifles with a variety of ammunition. For the three rifles used, the order of efficiency in initiating detonation in AN-FO mixtures was 220 Swift >300 Weatherby Magnum >30-&apos;06. The velocity of the bullet was found to be a decisive factor in the initiation. The sensitivity of various materials studied increased as follows: Clay-coated prills with 4 percent oil <fresh surfactant-coated prills with 4 or 6 percent oil <surfactant-coated prills with 4 or 6 percent oil and aged 270 days <crushed prills with 6 percent oil <very low-density, surfactant-coated prills (micronized), with 4 percent oil.

Jan 1, 1963

By J Hutchings

An essential component to the management of any process is the measurement of key parameters, used to monitor, control, and provide the feedback necessary for improvement. This paper discusses how data collection and analysis can provide a better understanding of the blasting process, as well as additional control and improved outcomes.The drill and blast process involves the generation and use of information at a number of levels. Comparison of historical parameters and results provides a starting point for the development of ongoing blast designs and a baseline against which future results can be compared. The collection of data during implementation provides a quality assurance/quality control (QA/QC) function where potential defects (such as under-drilled or over-charged holes) can be rectified prior to firing. Actual quantities and production rates allow the development of realistic plans and schedules, rather than using inaccurate estimates and targets that lead to unscheduled changes to equipment paths. Over?the past several years there have been a number of technological advances in data collection technology. Drill monitoring instrumentation on blasthole drills provides location information and feedback on rock properties as drilling occurs. Hand held ‘data logger’ technology has also overcome the challenges of working on the bench, such that blasthole measurements can be collected and forwarded directly to the explosive truck. Mine sites are becoming wireless network-enabled allowing the seamless data transfer from the field back to the office, in near real time, as that information is collected. Great strides have also been made in the development of drill and blast software systems which are more user friendly, and yet provide far greater capability to manage the quantity of data generated. The blasting process is critical to the overall mining process and the delivery of a successful blast outcome requires that the blasting process be ‘in control’. The measurement of key parameters can provide the data with which to measure and maintain control of blasting, and allows the validation of performance improvement measures and identification of improvement opportunities.

Nov 8, 2011

By Steve Axen

In situ mining is now considered an alternative mining method for some ore bodies. The in situ operation consists of a well field designed from reservoir properties and geological information; the wells for such a field are then drilled, cased, and cemented, using good designs and practices to eliminate future problems. Injection and production (recovery) systems are required to be corrosion resistant. Hand in hand with the mining operation is the metal extraction plant, the entire operation offering an environmentally acceptable method for metal recovery. Great opportunity exists in this field for mineral engineers; presently, they must borrow knowledge from other fields, since the schools have not yet addressed this specialty.

Jan 1, 1979

By F. Charette

The paper reviews the requirements of the instrumentation required to monitor mining excavations in a high stress environment, and the development plan to instrument the D-Bolt in such a fashion as to be able to follow the behaviour of the bolts in relationship to the ground movements and support performance. Recent field observations of D-Bolts under static and dynamic conditions are also presented. Also discussed is the assumed mechanical behaviour of the D-Bolt. D-Bolts are used in two (2) Canadian underground mines operating in high stress environments and tested in three (3) other operations.

Jun 1, 2012

By K. L. Fetters, F. M. Walters

ALL previous records were broken by the Iron and Steel Division, in the number of sessions, the number of papers, and the attendance. In addition to ten papers (all preprinted) on properties, structure, aid hardenability of, carbon and alloy steels, eight formal papers were presented on one or more phases of steelmaklng, and a symposium on the determination of hydrogen and nitrogen in steel. This last started at 2 p.m. and was going strong with more than a third of the audience still present at 6 p.m.

Jan 1, 1944

By Thomas W. Smelser

A full-scale geotechnical model of a 15-foot (4.6 m) wide coal mine entry in correlation with computer finite-element analysis (FEA) is being employed at the Bureau of Mines Spokane Research Center for basic research on roof-bolt support systems. Physical and computer modeling of various coal mine roof-bolt reinforcement systems will increase our basic knowledge of how roof supports function. This information, in correlation with computer FEA and underground verification tests, will provide a basis for establishing safer, more cost- effective roof control plans and help establish guidelines for employing fully grouted and conventional bolting systems. The basic rationale for the research, research approach, methods and equipment employed, results to date, and future research plans are described in this paper.

Jan 1, 1982

By B. R. Maas

Processing material at a consistent rate through the continuous countercurrent decantation (CCD) thickeners presented a major bottle neck to unlocking additional value from one of the post-flotation streams at the Kansanshi processing plant. The manual operation of the thickeners making up the CCD train resulted in frequent imbalances and process upsets across units. The automation of CCD trains is notoriously tricky as the available manipulated variables are outnumbered by the parameters requiring regulation. The implementation of an advanced, auction-based, control philosophy to manage the movement of both slurry and solution inventory through the train addressed this parameter imbalance and lead to the stabilisation of the circuit. Since the commissioning of this control strategy: an additional 7 200 dmt/day (+36% throughput) of material can reliably be processed through the train, the number of monthly downtime events has reduced, and a saving of $354 000/month in reagent cost has been achieved. INTRODUCTION CCD operation Agitated leaching is a common method used in hydrometallurgy to extract a metal from its host ore. The host ore is initially finely ground to liberate the surfaces of the valued minerals and improve the kinetics of the leaching process. The ore is then contacted in an agitated tank with a lixiviant to dissolve the desired metal into the aqueous phase. The resultant slurry from the leaching process comprises of a solution pregnant in the metal salt and a barren ore. The first purification step taken after leaching is to wash the pregnant liquor solution (PLS) from the depleted ore. On the industrial scale, a set of between two to ten thickeners arranged in a countercurrent configuration is often used to carry out this separation (Perry & Chilton, 1973). The slurry is introduced at the head of the train and a wash solution at the tail. The two streams are pumped through each thickener countercurrent to one other. At each stage the residual PLS in the slurry is mixed and diluted down with the countercurrent overflow solution from the downstream thickener. The diluted slurry is fed into the thickener where the solids separate out through gravity sedimentation. The settled solids are channelled towards the underflow of the thickener by a rake mechanism and pumped downstream to the next thickener in the train. The outcome is the recovery of a PLS from the overflow of the lead thickener and a slurry of washed solids from the underflow of the tails thickener.

Jan 1, 2019

By Sharpin P. C

The countercurrent gas-solid heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temperature distributions through the drier have been calculated. Although the calculations rest on several simplifying assumptions, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating conditions on the rate of drying of the briquettes which controls the strength of the char produced. The analysis shows why a limitation was reached in the improvement of char strength in the pilot plant in 1961 due to the performance of the drier and a prediction is made of a way in which the limitation could be overcome.

Jan 1, 1966

By J. F. Wright

During the last three years prospecting has been active in southeastern Manitoba and a number of interesting gold, nickel and copper deposits have been discovered within an area 90 miles north of the international boundary, and extending about 40 miles westerly from between mileage 60 and 110 on the Manitoba-Ontario boundary. As known at present, two-thirds of this area of 2,000 square miles is underlain by pre Cambrian granite and granite gneiss and is not likely to contain mineral deposits of economic importance. The remaining one-third is underlain by metamorphosed sediments and lavas (greenstones), penetrated by the granite and granite gneiss and, at various localities, cut by bosses, sills, or dykes of gabbro, diorite, granodiorite, and other types of intrusives. The nickel, copper, and gold mineralization accompanied or followed the intrusion of these different rock types. The gold deposits are limited in distribution, so far as known, to the northern part of this prospecting area and occur along Manigotagan and Wanipigow rivers. These deposits have recently been described in some detail, (3) and therefore only the copper and copper-nickel deposits of the southern part of this area, along Oiseau and Maskwa rivers, will be described in this paper.

Jan 1, 1925

By C. J. B. Dreyer

In terms of resources of amphibole asbestos only South Africa can be considered. There are only two asbestos producing fields, one in the Northern Cape Province producing only crocidolite and one in the Eastern Transvaal producing only amosite. The banded ironstone sequence in which amphibole asbestos occurs is discussed, and the genesis of the fibre is briefly reviewed. The properties and characteristics of amphibole asbestos are discussed and compared to those of chrysotile. Approximately 300,000 tonnes of amosite and crocidolite are produced annually. Crocidolite has a potential for a fivefold increase of production, which could be sustained beyond the year 2000. An estimate of the resources of the various producing fields in South Africa is made. Mining methods are reviewed and evaluation techniques discussed.

Jan 1, 1978

By Jie Li, Wenzhou Yu, Xuewei Lv

An efficient enrichment of primary silicon from the Al–Si melt can be beneficial for the Si purification and the cost reduction of the solvent refining process. In this paper, an alternating magnetic field was used to enhance the mass transfer and promote the crystal growth of primary silicon during the directional solidification of hypereutectic Al–Si alloy. The results show that the growth rate and morphologies of Si crystals changed continuously along the directional solidification direction. With the decreasing of Si content in the melt and the weakness of the electromagnetic stirring, the crystal growth rate of primary silicon gradually decreased and the Si morphologies changed from planetocellular ,cellulardendrite, and columnardendrite, respectively. This provides a deeper understanding of the Si crystal growth during the electromagnetic solidification, which will be good for achieving a high-efficiency enrichment of primary silicon in Al–Si melt.

Mar 1, 2018

By Reinaldo J. Villa, Joshua C. Adams

The I-395/SR-836/I-95 reconstruction project is an $818-million design-build construction effort that includes construction of viaduct, segmental and signature bridges in Miami leading into Miami Beach in Florida. Based on the load testing performed during the design phase, the design-build team determined that conventional driven pile and drilled shaft foundations were not feasible for support of segmental and signature bridges. Due to the weak limestone formation and successful use of auger cast-in-place (ACIP) piles in the Downtown Miami area on commercial developments, ACIP piles were selected as a foundation system to support bridges. This is the first time in history where the bridges will be supported by ACIP pile foundations in an interstate highway in the State of Florida. The design build-team worked closely with the Florida Department of Transportation to develop requirements for the load test program. The paper will provide an overview of the geotechnical data collected, results of dynamic/bi-directional load testing performed on test piles, data collected, installation of piles, and lessons learned. The load test program included a total of fifteen test piles with dynamic, bi-directional, and lateral load testing on 30 and 36-inch diameter ACIP piles and instrumented with thermal integrity profiling wires.

Sep 8, 2021