Search Documents

By Edward (Ted) Dowey

City Water Tunnel No. 3 is being built in order to provide a redundant system for delivering 4,542,500 m3 (1.2 billion gallons) of water per day throughout the five boroughs of New York City. The present tunnels, City Tunnel No. 1 and 2 (Figure 1), were put in service in 1917 and 1936 respectively, and both have been in continuous service. Tunnels No. 1 and 2 can-not be shut down for inspection or repair until City Tunnel No. 3 has been completed. City Tunnel No. 3 has two stages (Figure 1).Stage One is 20.1 km (12.5 mi) long and is presently delivering drinking water to the boroughs of the Bronx and Manhattan. Stage Two consists of the Brooklyn-Queens Tunnel 17.7 km (11 mi) and the Manhattan Tunnel 14 km (9 mi). The Brooklyn-Queens leg is complete and is set to be put in service soon. The Manhattan Tunnel is being constructed and is the subject of this paper. The Manhattan Tunnel (Figure 1) is comprised of three legs: the north, south and east legs. The con-tract includes the excavation of 8,976 m (29,500 ft) of tunnel and the lining of 14,561 m (47,773 ft) of tunnel. The south tunnel, 5,705 m (18,720 ft), was excavated but not lined, under a previous contract. The tunnel ranges from 181 m (600 ft) to 152 m (500 ft) in depth in the bedrock under Manhattan. The tunnel contract also includes the construction of nine new shafts, 161 m (530 ft) average depth, and the completion of a tenth shaft (the previously built construction shaft). The Manhattan Tunnel contract was awarded to the sole bidder Schiavone/Shea/Frontier Kemper Joint Venture (SSF) for $668,532,680.00, on January 31, 2005. The Manhattan Tunnel was designed ?in house? by the New York City Department of Environmental Protection (DEP) and the construction management was provided by a combined staff of the DEP and a joint venture of Jenny Engineering and URS.

Jan 1, 2008

By S Henderson

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Microprobe analyses.of sphalerite grains from the Waitangi deposit mostly range from 0.8 to 1.5 mole % FeS, although one sample contains 9.5 mole % FeS. Arsenopyrite from Waitangi yields a range from 33.1 to 34.6 atomic As (%). There is no discernible correlation between the FeS content of sphalerite and gold grade in the Waitangi deposit suggesting that gold deposition is probably not controlled by changes in temperature and activity of sulphur aS2 that control the FeS content of sphalerite. The possible causes for gold deposition are thought to be boiling, mixing and changes in pH. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-ehalcopyrite samples yield a narrow range of d34SCDT values (-1.0 to 0.9 ë;n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source. However, the source of light sulphur in the late pyrite grains is not known. Preliminary fluid inclusion+studies indicate homogenisation temperatures between 173¦ and 284¦C and salinities of 0.23.0 NaCI equiv. wt % (uncorrected for C02). Vein quartz at Waitangi yields d18OSMOW values from 6.8 to 12.7 ë (n=23). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1-5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in d18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that d18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1993

By M. K. Jain, Z. T. Xu, M. Bruhis, V. Hegedekatte

"Strain rate and temperature dependent deformation conditions are present during elevated temperature forming of aluminum and other metallic materials. While many constitutive laws have been proposed to represent such deformation conditions, a closer investigation often reveals their limited applicability in terms of fit to the experimental data, and interpolation within and extrapolation outside of the range of experimental stress-strain curves. This is often because material-specific primary deformation mechanisms of temperature-dependent strain and strain rate hardening are poorly captured. In the present work, the Voce-Kocks constitutive model based on mechanics of dislocations storage and annihilation has been found to be suitable for many metallic materials. The model was modified to include the effect of temperature dependent shear modulus. The modified model is then employed to represent the experimental data obtained from uniaxial tensile tests on AA7075-O sheet at elevated temperatures and strain rates. Also, hot gas bulging tests were conducted to verify the applicability of this model. Further, finite element simulation of the hot gas bulge test was performed by incorporating the model as a user material subroutine. Good general agreement was observed between the experimental and FE model predicted results. Some sources of discrepancy in the prediction are also discussed.INTRODUCTION There has been much interest in light-weighting of automobiles from automotive related industries to reduce overall carbon footprint and increase energy efficiency of the vehicles. Aluminum alloys, and especially the medium-strength 5xxx and 6xxx series alloys, have been the primary focus in the last 3 decades to reach the above environmental goals (Huo, Hou, Zhang, & Zhang, 2016) whereas aerospace industry has traditionally focused on high strength 7xxx series aluminum (Al-Zn-Mg-Cu) alloys for structural components (Deng, Yin, & Huang, 2011). Recently, there has been much interest in high strength 7xxx series aluminum as a replacement for heavier steel automotive structural parts such as A-pillar, B-pillar, side impact beams etc. (Harrison & Luckey, 2014). This is both interesting and challenging since the above aluminum structural parts will need to not only meet impact safety standards but also possess sufficient formability for manufacturing such complex parts. Since the formability of high strength 7xxx series materials is quite poor at room temperature, much interest has focused on improving both formability and final part strength via high rate hot stamping, in-die quenching, and subsequent artificial ageing process steps (Kumar & Ross, 2016)."

Jan 1, 2018

By O. C. Blade, Elizabeth Hughes

Conservation in the utilization of any product is always subject to improvement if the composition and properties of the product are known. Petroleum is no exception, and knowledge of the characteristics of crude oils, even when given on the broad basis of routine type analyses has proved useful to chemists, engineers, and geologists in improving pro- duction and utilization of petroleum. For a quarter of a century the Bureau of Mines has sought to provide such information regarding crude oils and has analyzed many samples of petroleum by its standardized rou- tine method. Most of these analyses have been published, sometimes in special compilations, other times in connection with reports of research on petroleum. This report is a finding index for all analyses published up to January 1, 1948. The routine method used for all these analyses is basically the same as that described by Dean, et al.. Briefly, the procedure consists of testing by standard methods, small samples of a crude oil for gravity, sulfur, color, and viscosity, and of distilling a sample of the crude oil by a standardized procedure and determining certain properties in the sep- arated fractions and residuum. Careful records are made during the proce- dure, and the distillation data obtained are used to calculate the approx- imate amounts of products present in the sample such as percents of gas- oline, kerosine, gas oil, and lubricants. The data obtained are recorded on a standard analytical report form. An analysis of a sample of typical midcontinent crude oil is shown in table 1. Compilation of these analyses, sometimes in tabular form and usually for specific geographic areas, are published from time to time. Analyses are often shown in connection with other studies, such as engineering field reports. This bibliography is a compilation of references to 115 publications, which contain analyses of crude oils by the Bureau of Mines. References may be found to analyses of crude oils from the United States, Canada,

Jun 1, 1948

By D Olivier

De Beers' Finsch Mine is situated in the Northern Cape province, 170 km northwest of Kimberley. The concentrator facility, designed and constructed by Bateman Engineering, was commissioned in 1967 and upgraded in 1979 using diamond liberation and extraction technology available at the time of design. Since then significant advances in diamond processing and technology have been made and these -have been incorporated into the new main treatment plant and recovery plant flowsheets, making diamond liberation and recovery from the Pre-1979 dumps a viable economic option at Finsch."

Jan 1, 2010

By G. R. Leverant, M. Gell

The high- and low-cycle fatigue poperties of MAR-M200 directionally -solidified into columnar-grained and single crystal forms were determined at 1400" and 1700°F. These results were compared with the corresponding properties of conventionally -cast MAR-M200. The low-cycle fatigue lives of the columnar-grained and single crystal materials were similar at both temperatures and were one to two orders of magnitude greater than those of conventionally-cast material. The variations in the fatigue lives among the three forms of MAR-M200 were related to the more rapid rate of intergranular muck propagation compared to that of transgranular propagation. In conventionally-cast MAR-M200, cracks were initiated in grain boundaries and crack popagation occurred rapidly along an almost continuous grain boundary path. In the columnar-grained material, crack initiation occurred on short transverse segments of grain boundaries, but crack propagation was transgranular. The fatigue lives of columnar-grained and single crystal materials were approximately the same because most of the life in both materials was spent in trans-granular propagation. For the directionally -solidified materials, the number of cycles to failure, Nf, can be related to the total strain range, , by: heT = K where n and K are 0.16 and 0.044 at 1400'F and 0.29and 0.098 at 1700, respectively. In addition to intergranular crack initiation in the columnar-grained material, initiation also occurred at we-cracked MC carbides and micropores in both directionally-solidified materials. At 1400°F, fatigue life was reduced with increasing MC carbide size, but at 1700 there was no effect of carbide size. THE creep and stress-rupture properties of conventionally-cast nickel-base superalloys can be greatly improved by directional solidification into either single crystal or columnar-grained forms. The improvement in properties results from a reduction in intergranular cavitation and crack growth in the columnar-grained materials and the complete absence of this fracture mode in the single crystals. This paper describes the effect of grain boundaries on the elevated temperature fatigue properties of the nickel-base superalloy MAR-M200. The effect of cycling frequency on cracking arid fatigue life and the role of MC carbides and micropores on crack initiation are also emphasized. The fatigue properties of columnar-grained and single crystal MAR-M200 at room tem- perature,4,5 and the change in the mode of fatigue crack propagation with temperature6 have recently been described. I) EXPERIMENTAL PROCEDURE The material used in this study was the nickel-base superalloy MAR-M200, directionally-solidified into columnar-grained and single crystal forms. The columnar grains were approximately 0.5 mm in diam. The nominal composition of these materials in wt pct was 0.15C, 9Cr, 12.5W, loco, 5A1. 2Ti, lCb, 0.05Zr. 0.015B, bal Ni. They were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr. which resulted in 0.2 pct offset yield stresses of 150,000? 144,000, and 95,000 psi at room temperature? 1400°, and 1700°F, respectively. The corresponding elastic moduli parallel to the testing direction were 19.2. 15.0, and 12.5 x 106 psi, respectively. Specimen design, testing procedures and alloy mi-crostructure have been described previously and will only be summarized here. Following the 1600°F aging treatment. MAR-M200 contains an ordered, cuboidal, y' precipitate 0.3 1 on edge, which is coherent with the 1 matrix. The y' precipitate is quite stable; even after testing at 1700°F. the precipitate is only slightly enlarged and its corners somewhat rounded. The alloy also contains a small volume fraction of micropores, and MC carbides. some of which contain preexisting cracks5 formed during casting. These cracks are always parallel to the long dimension of the carbide. Measurement of MC carbide size has been described previously.5 Axial fatigue tests were conducted in air over a wide range of strain amplitudes in both the high - and low-cycle fatigue regions, with specimen lives varying from about 10' to 10' cycles. Low-cycle fatigue (LCF) tests were strain-controlled with strain varied between zero and a maximum tensile value at a frequency of about 2 cpm. High-cycle fatigue (HCF) tests were stress-controlled with the stress varied between 5000 psi and a maximum tensile value less than the yield stress at a frequency of either 10 cps or 0.033 cps (2 cpm). The temperature in the gage section was controlled to 52°F. Specimen axes were within 5 deg of the [001] growth axis of the single crystals and the common [001 ] growth axis of the columnar-grained material. Specimen gage sections were electro polished prior to testing. After the standard heat treatment, three specimens were coated with a typical aluminide coating applied as a slurry. An additional specimen was given the coating heat treatment without actually being coated. In all cases: specimens were reaged at 1600°F for 32 hr after receiving the coating heat treatment at 1975'F for 4 hr.

Jan 1, 1970

By Zhou Junwu, Han Long, Song Zhenguo, Sun Chuanyao

The deposit genesis, the ore property, and the mineral characteristics, which has a close relationship with the beneficiablity, could be regarded as the “Genetic Properties”, actually are the determining factors for beneficiation process development. However, in conventional concentrator’s process development and engineering, there have been lack of systematic research and test on those genetic properties, also lack of well-established collecting, statistics and analysis system for those huge amount of data such as the historical mineral processing technique research, process mineralogy study, practical operating and engineering data. Obviously it is far less than enough for profound integration combining modern IT together with traditional mineral processing technology, as a result there are a number of disadvantages in mineral processing R&D and engineering, such as long term, high cost, low efficiency as well as repetitive testwork not making full advantage of previous experiences. Aiming to make utmost of those Genetic Properties and overcome above disadvantages in mineral processing R&D and engineering, the concept of “Genetic Mineral Processing Engineering (GMPE)” is put forwarded, and the strategical study has been conducted on this regard, with the main focus on following aspects: a) Testing and extraction of the “Genetic Properties”; b) Establishment of data base and data warehouse of GMPE; c) Intelligent decision making system for beneficiation process; d) Verification testwork; e) Virtual concentrator. The technical route proposed is to firstly conduct research and test on those Genetic Properties mentioned above, based on that the specific data base will be set up and applied for intelligent process recommendation and simulation with a few verification testwork conducted in the meantime, finally achieve a fast, high efficiency and precise determination of technology and process for ore beneficiation. The systematic study on the three-in-one GMPE would make an innovative breakthrough in conventional mineral process testwork research and engineering methodology, and provide technical support for the concentrator’s design and upgrading.

Jan 1, 2018

By Bing Hu, Zhu-Cheng Huang, Guang-Bin Xia, Hu Peng, Hua Wang

"The temperature rising characteristics and reaction of the reduction of iron oxide pellets with anthracite fines were studied using a MW-L0316V microwave oven and Leica-DM-RXP polarizing microscope. The results show that iron oxide pellets and anthracite fines have good microwave absorbing properties, and high temperature and reducing atmosphere in a relatively short time for reduction of iron oxide pellets can be achieved. The reduction reaction, which follows the unreacted core model, is rapid and the metallization increases from 13.41% to 56.57% as the reduction end point temperature increases from 850oC to 950oC. The iron is formed, fine grain crystals of iron are transferred and the contraction of metal phase occurs firstly at the surface of pellets, which hinders the reduction reaction at the center of pellets. The rate of reduction reaction increases slowly as the reduction end point temperature increases from 950oC to 1050oC.IntroductionIron ore direct reduction can be divided into gas-based reduction and coal-based reduction. Owing to the effect of the resource and the related economic benefits [1, 2, 3, and 4], the development of gas-based direct reduction technology is restricted, but the development of coal-based direct reduction supported by the relevant industrial policy has very good prospects for application.As a source of clean energy, in China microwaves have been applied in many fields [5, 6, and 7]. Chen Jin studied the reduction of carbon pellets under microwaves, and has made some progress on reduction kinetics and reaction mechanisms. Other countries also have related research in this field [8 - 15], for example, Kotaro Ishizaki and Kazuhiro Nagata have done research on the reduction reaction of carbon magnetite heated by microwaves. The research shows that Fe3O4 is deoxidized to FeO at about 800oC, and FeO is deoxidized to Fe at 1000oC-1025oC. Due to the very good heat absorbing properties of iron oxide pellets and anthracite fines, the selective and rapid heating of microwaves can rapidly raise the temperature of pellets and anthracite, and the iron oxide pellets can be rapidly reduced. In order to provide enough theoretical basis for direct reduction by microwave heating, this paper studies the temperature rising characteristics, behavior of the reduction reaction and the changes of the iron oxide pellets and anthracite in the microwave field."

Jan 1, 2011

By Thomas T., Read

IT is difficult to judge how much influence the success attained during its first year, 1864-65, by the School of Mines at Columbia had on developments in education for the mineral industry elsewhere in the immediately subsequent years. The facts are as follows: 1. The Massachusetts Institute of Technology began giving instruction in February 1865, with a mining course included in its curriculum. 2. Early in 1865 the faculty of the Department of Science, Literature and the Arts of the University of Michigan requested permission from the Regents to establish "a course of study to be called the School of Mines . . . Also that the degree of Mining Engineering, be conferred on students who should complete the course of study prescribed in the same." A resolution authorizing this was adopted by the Regents on March 28, 1865. 3. Samuel Hooper endowed a Sturgis-Hooper professorship of geology at Harvard in 1865 with the intention of making it a nucleus of a new School of Practical Mining and Geology. 4. Yale appointed Alfred P. Rockwell professor of mining in 1865. 5. Lafayette College appointed Henry S. Osborn professor of mining and metallurgy in 1865. 6. Washington College (as Washington and Lee was then known), rising out of the ashes of Civil War destruction, made a fresh start in 1865, with Generalized as its president, and offered a mining course in the first catalogue thereafter published. 7. Lehigh University, founded in 1866, had a mining curriculum from its beginning. 8. Rensselaer Polytechnic began offering a curriculum in mining and metallurgical engineering in 1867. It would be natural to suppose that these events were a reaction, to the success of the school at Columbia, - and possibly they

Jan 1, 1941

By William Reisz

In our line of work,like many other professions, there may be times when circumstances or a series of events may arise, contributing toward unacceptable risk. When multiple parties are involved, there will almost inevitably be differences on how best to deal with these situations. Unless approached in an intelligent and these differences may often have the potential for costly and unexpected results.

Jan 1, 2014

By K Orth

The volcanic successions that host massive sulphide deposits are diverse in composition, facies types and facies relationships. They also show a variety of spatial and temporal relationships to mineralisation. In many examples, such as the Koongie Park Formation in Western Australia, the host succession includes more or less conformable syn-volcanic sills with peperitic contacts. Such sills can be an important source of heat for fluid circulation, influencing patterns of hydrothermal alteration and the location of co-eval and later mineralisation. The impact of syn-volcanic sills on the host succession depends in part on the initial porosity and permeability of the enclosing facies. The special properties of glassy pumice û being highly porous, permeable, and reactive û allow pumice-rich facies to preferentially focus hydrothermal fluid flow. However, the same properties promote early alteration and porosity reduction. Hence, the diagenetic and compaction history of pumiceous facies strongly influences their potential to host massive sulphide mineralisation. In contrast to pumice, dense glass has relatively low porosity, at least initially, and does not compact. Non-vesicular glass is a major component of submarine lavas, syn-volcanic intrusions and some volcaniclastic facies. However, especially in submarine settings, dense glass is commonly intensely perlitically fractured soon after eruption. The fractures greatly increase the porosity and permeability, locally accelerating diagenetic and hydrothermal alteration. In addition to false pyroclastic textures, altered perlite may exhibit false porphyritic textures. Silica- or feldspar-altered perlite kernels surrounded by intensely altered phyllosilicate domains can resemble phenocrysts in a fine grained groundmass.

Jan 1, 1999

By David S. Yang, Osamu Taki

The innovative Soil-Cement Mixing Wall Technique, developed independently in Japan, consists of mixing in-place soils with cement grout using multi-axis augers and mixing paddles to construct overlapping soil-cement columns. The applications of overlapped soil-cement columns include cutoff walls for groundwater control and structural diaphragm walls for excavation support. The special features of this technique include water tightness, versatile strength design, and efficient installation in subsurface materials varying from clayey soils to cobbles or soft rocks. Through the introduction of two recent subway projects in Japan, this paper presents the design parameters, construction procedure, quality control and performance of soil-cement wall for excavation support and groundwater control.

Jan 1, 1989

By Akihide Nagao

The behavior of impurity hydrogen that is contained in starting material or picked up during processing has been little investigated up to now. The hydrogen microprint technique is applied to determine the microscopic location of impurity hydrogen during deformation in aluminum without hydrogen charging. Three kinds of pure aluminum of 99.99% are prepared, in which hydrogen content is varied by changing the atmosphere when they are melted and heat-treated. After rolling, tensile specimens with a gage size of 4 x 4 rnm and 0.5 mm in thickness are stamped out from these three kinds of aluminum sheets. These specimens are covered with a liquid nuclear emulsion of silver bromide crystals, stretched by 5,10 and 15 percent plastic strain or fractured, developed and fixed. SEM micrographs reveal a number of silver particles on the slip lines and on the grain boundaries. Also shown is that the more hydrogen present in the specimen, the more silver grains appear on the slip limes and on the grain boundaries. Consequently, it is concluded that impurity hydrogen is transported to the surface with gliding dislocations during deformation.

Jan 1, 1998

By Julian S. Edwards, C. Frederick C. Pearson, Sevket Durucan

Information gained at the site investigation stage of the Carsington aqueduct project led the designers to suspect that methane might be encountered during tunnelling and therefore gas detection techniques, including emergency shutdown systems, were introduced. After construction, on completion of the excavation and lining of the tunnels, a survey showed that methane was entering the aqueduct dissolved in infiltrating groundwater. General body air concentrations were very low but on closure methane concentrations rose rapidly within the aqueduct. A research project has now been initiated to investigate the mechanism of methane generation and entry rate into the system, the results of which are being taken into account in the preparation of future operating procedures.

Jan 1, 1989

By Michael Arriagada, Ivan Arriagada

"As mines return to shafts to economically exploit deeper reserves, two methods mine owners use to minimize short term costs are: sinking shafts in phases and refurbishing old, existing shafts. While there may appear to be benefits to utilizing existing infrastructure, often this is not the case, resulting in missed deadlines and added costs. Similarly, if proper long term planning is not executed when sinking a shaft in phases, additional costs and downtime will be accrued. This paper will take an in depth look at both of these options with an eye towards optimizing costs, minimizing downtime, and facilitating construction. INTRODUCTION With the onset of mechanized mining and large capacity trucks, many mines turned away from shafts and began to use ramps to haul ore to surface. However, continual exploitation of mineral reserves located closer to surface, combined with the subsequent unearthing of additional resources at greater depths, forced mines to go deeper and deeper to extend the life and keep the operation running. In shallow mines, hauling ore by truck was an economical option. However, as mines get deeper, driving ramps takes additional time, and hauling over longer and longer distances becomes less economic, both in terms of cost and time. For this reason Mexico, in particular, has seen a jump in the number of shafts which have been put into production, as well as having a number of shafts in different stages of development and still more in the conceptual stages. Many of the shaft projects in Mexico are being designed in phases, with the hoist and equipment purchased capable of reaching the ultimate planned depth of the shaft, but with sinking operations stopping short at an intermediate depth. A loading pocket is then installed to start exploiting mineral at this depth sooner, with subsequent phases planned for a later date using either a rock pentice or bulkhead to separate the sinking operations from the active shaft above. Currently, we are directly involved in two such projects which are actively being deepened, as well as having seen various others already reach completion. If done properly with the long-term plan in mind, sinking in phases can be a very viable option, allowing for faster production while fully utilizing the equipment at various depths. However, there are many issues which can arise when sinking a shaft in phases that if not properly examined and planned for from the outset, have the potential to eliminate the gains hoped for when it was decided to sink in this manner."

Jan 1, 2019

By Seyyed Mehdi Radeghi Mehrjou

It is important to study structures and their retrofitting techniques in order to avoid earthquake-induced seismic damage within countries that are prone to earthquakes. Todays, micro piles are employed as useful structural components for seismic behavior improvement. The present study analyzes inclined micro piles subjected to seismic loading by using the three-dimensional finite difference method (FDM). FDM assumes an idealized three-dimensional soil-micro pile model to perform logical behavior evaluation in the event of an earthquake. Linear and elastic micro piles and elastoplastic soil were employed in this study. The Mohr-Coulomb criterion was employed in the failure control of the micro piles. The micro piles were subjected to the 1978 Tubas earthquake records. The numerical results were compared to experimental data. The comparison revealed good agreement between the numerical results and experimental data. The inclined micro piles were found to sufficiently enhance soil strength under seismic loading, inducing smaller displacements than vertical micro piles. Furthermore, the soil and inclined micro piles showed salient interaction.

Sep 1, 2022

By G. Chung, W. Petruk, D. Doyle

"A series of tests was conducted on Carol Lake iron ore, which contains about 38 wt % hematite and 19 wt % magnetite, to establish a flowsheet for high weight yield by spirals. A pilot plant was run in parallel with the IOC concentrator to simultaneously test two flowsheets on the same feed material. The IOC concentrator processes the ore by treating it directly in a spiral circuit, whereas the pilot plant used a laconite flowsheet which had a low intensity magnetic separator (LIMS) at the front of the circuit. The LIMS produced a non-magnetic (hematite-rich) product and a magnetic (magnetite-rich) product prior to treating the ore in two separate spiral circuits. The results from about 150 tests were evaluated by chemical assays and materials balancing techniques, and a selected test was evaluated by the image analysis and materials balancing technique.The image analysis and materials balancing evaluation showed that a higher hematite recovery was obtained by the hematite spiral circuit than by the IOC concentrator spiral circuit, and a slightly lower magnetite recovery by the magnetite spiral circuit than by the IOC concentrator spiral circuit. Furthermore the hematite recovery by hematite spirals was higher than the magnetite recovery by magnetite spirals. The better hematite recovery was achieved because a higher liberation is obtained for hematite than for magnetite, and the hematite in the Carol Lake ore has a narrower grain size range than magnetite. Consequently, better spiral control can be maintained when processing a hematite-rich spiral feed, than when processing a magnetite-rich spiral feed. Since the feed to the IOC concentrator spiral is a mixture of hematite and magnetite, an intermediate hematite recovery is obtained by the IOC concentrator. INTRODUCTIONA study of characteristics that affect recoveries of hematite and magnetite from the Carol Lake ores of the Iron Ore Company of Canada (IOC), was carried out in connection with a project on designing a flowsheet for maximum weight yields. A pilot plant using a taconite flowsheet was run in parallel with the existing IOC concentrator which uses a classical iron ore flowsheet. About 150 tests were run to compare iron recoveries and weight yields by the spirals in the two flowsheets. Better iron recoveries were indicated for the taconite flowsheet, but the results were not consistent and the reasons for the observed differences were not apparent. The material from one test (Test 61), which gave better iron recoveries for the taconite flowsheet, was evaluated by the image analysis and materials balancing technique. A suite of samples was taken from 5 points in the IOC concentrator and from 8 points in a pilot plant (taconite flowsheet). The samples were analyzed to compare the behaviours of the Carol Lake hematite and magnetite in the spirals of the two flowsheets. The results provided a sound basis for further tests in designing a high weight yield flow sheet."

Jan 1, 1993

By Lijuan Chen

During the detoxification of chromium-containing slag by Achromobacter sp. CH-1, anionic surfactant Sodium Dodecyl Sulphate(SDS) and its mixed systems with different Tween surfactants(Tween 20, Tween 60 and Tween 80) were used to promote the interaction between the bacteria and the chromiumcontaining slag and the rate of acid-soluble Cr( ? ) leached from the slag. The effects were evaluated by the surface tension, the pH of the leaching solution and the leaching rate of total Cr( ? ) from the slag. The results showed that the surfactants systems improved Cr(VI) leaching and its detoxification of chromium-containing slag. The mixed surfactants of SDS combined with Tween surfactant revealed better effectiveness of detoxification than SDS only. When the mass ratio of SDS to Tween 80 was 1:1, the rate of Cr( ? ) leached from the slag increased by 12%.

Jan 1, 2009

By Lee Ann Arrington-Webb

Thiele Kaolin Co. has invested much time and money in achieving and maintaining its IS0 9002 certification. Through a regimen of process control and documentation, routine audits and a commitment to quality management, this kaolin producer is a competitive pigment supplier in a worldwide market. Background In 1987, the International Organization for Standards developed the ISO 9000 quality management system. This series of standards is used as a means to ensure customers that a quality management system is in place. Certification of a company does not mean that an individual product is of high quality. Rather, it demonstrates a supplier's ability to meet its customers' product and service needs. It also shows that a company has documented records to assure product consistency. The ISO 9000 system was begun in England during the early 1980s. During the mid-1970s, the British manufacturing industry was experiencing low quality. In an attempt to boost quality standards, the British government established the BS 5750 standards system. In 1987, BS 5750 was incorporated into ISO 9000. The ISO 9000 series consists of three levels of certification. ISO 9001 is the model for quality assurance in "design/development, production, installation and servicing." This standard applies to companies that rely on research and development to bring products that frequently change to market. ISO 9002 involves "production and installation" only. This standard is relevant to industries that produce a specific product according to specifications - either their own or their customer's. ISO 9003 is the model in "final inspection and test." This standard is the least detailed of the 9000 series. It is also the most applicable to companies that purchase, inspect or sort and resell. The quality system requirements for certification are outlined in the 18 elements of ISO 9002. These include: 4.1 - Management responsibility. 4.2 - Quality systems. 4.3 - Contract review. 4.4 - Design control. 4.5 - Document and data control. 4.6 - Purchasing. 4.7 - Control of customer-supplied product. 4.8 - Product identification and traceability. 4.9 - Process control. 4.10 - Inspection and testing. 4.11- Control of inspection, measuring and test equipment. 4.12 - Inspection and test status. 4.13 - Control of nonconforming product. 4.14 - Corrective and preventive action. 4.15 - Handling, storage, packaging, preservation and delivery. 4.16 - Control of quality records. 4.17 - Internal quality audits. 4.18 -Training. Continuous improvement, though implied in maintaining these requirements, could potentially be included in the quality system requirements in the next revision. The ISO 9000 requirements and documentation system is shown in the hierarchy pyramid (Fig. 1). A company's quality policy serves as the top of the pyra-

Jan 1, 1997

By Charles L. Harnes

A mineral pigment is a colored substance dug from the ground, which after treatment can be mixed with a drying oil to form a paint. Not all colored earths, however, can be made into satisfactory pigment. Much depends upon the attractiveness and uniformity of the color and the ease of purification. Mineral pigments are distinguished from chemical pigments by a difference in origin and treatment. Chemical pigments are not found ready-made in the earth but must be synthesized or otherwise obtained from other compounds or elements; for example, cadmium yellow, a chemical pigment, is precipitated from a solution of cadmium chloride, hydrochloric acid, and sodium sulfide.

Jan 1, 1942